43f2f10444
Sky2 driver will oops referencing bad memory if used on a dual port card. The problem is accessing past end of MIB counter space. Applies for both 2.6.17 and 2.6.16 (with fuzz) Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
3422 lines
90 KiB
C
3422 lines
90 KiB
C
/*
|
|
* New driver for Marvell Yukon 2 chipset.
|
|
* Based on earlier sk98lin, and skge driver.
|
|
*
|
|
* This driver intentionally does not support all the features
|
|
* of the original driver such as link fail-over and link management because
|
|
* those should be done at higher levels.
|
|
*
|
|
* Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
|
|
#include <linux/config.h>
|
|
#include <linux/crc32.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/version.h>
|
|
#include <linux/module.h>
|
|
#include <linux/netdevice.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/etherdevice.h>
|
|
#include <linux/ethtool.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/ip.h>
|
|
#include <linux/tcp.h>
|
|
#include <linux/in.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/workqueue.h>
|
|
#include <linux/if_vlan.h>
|
|
#include <linux/prefetch.h>
|
|
#include <linux/mii.h>
|
|
|
|
#include <asm/irq.h>
|
|
|
|
#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
|
|
#define SKY2_VLAN_TAG_USED 1
|
|
#endif
|
|
|
|
#include "sky2.h"
|
|
|
|
#define DRV_NAME "sky2"
|
|
#define DRV_VERSION "1.1"
|
|
#define PFX DRV_NAME " "
|
|
|
|
/*
|
|
* The Yukon II chipset takes 64 bit command blocks (called list elements)
|
|
* that are organized into three (receive, transmit, status) different rings
|
|
* similar to Tigon3. A transmit can require several elements;
|
|
* a receive requires one (or two if using 64 bit dma).
|
|
*/
|
|
|
|
#define RX_LE_SIZE 512
|
|
#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
|
|
#define RX_MAX_PENDING (RX_LE_SIZE/2 - 2)
|
|
#define RX_DEF_PENDING RX_MAX_PENDING
|
|
#define RX_SKB_ALIGN 8
|
|
|
|
#define TX_RING_SIZE 512
|
|
#define TX_DEF_PENDING (TX_RING_SIZE - 1)
|
|
#define TX_MIN_PENDING 64
|
|
#define MAX_SKB_TX_LE (4 + (sizeof(dma_addr_t)/sizeof(u32))*MAX_SKB_FRAGS)
|
|
|
|
#define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
|
|
#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
|
|
#define ETH_JUMBO_MTU 9000
|
|
#define TX_WATCHDOG (5 * HZ)
|
|
#define NAPI_WEIGHT 64
|
|
#define PHY_RETRIES 1000
|
|
|
|
static const u32 default_msg =
|
|
NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
|
|
| NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR
|
|
| NETIF_MSG_IFUP | NETIF_MSG_IFDOWN;
|
|
|
|
static int debug = -1; /* defaults above */
|
|
module_param(debug, int, 0);
|
|
MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
|
|
|
|
static int copybreak __read_mostly = 256;
|
|
module_param(copybreak, int, 0);
|
|
MODULE_PARM_DESC(copybreak, "Receive copy threshold");
|
|
|
|
static int disable_msi = 0;
|
|
module_param(disable_msi, int, 0);
|
|
MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)");
|
|
|
|
static const struct pci_device_id sky2_id_table[] = {
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) },
|
|
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) },
|
|
{ 0 }
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(pci, sky2_id_table);
|
|
|
|
/* Avoid conditionals by using array */
|
|
static const unsigned txqaddr[] = { Q_XA1, Q_XA2 };
|
|
static const unsigned rxqaddr[] = { Q_R1, Q_R2 };
|
|
|
|
/* This driver supports yukon2 chipset only */
|
|
static const char *yukon2_name[] = {
|
|
"XL", /* 0xb3 */
|
|
"EC Ultra", /* 0xb4 */
|
|
"UNKNOWN", /* 0xb5 */
|
|
"EC", /* 0xb6 */
|
|
"FE", /* 0xb7 */
|
|
};
|
|
|
|
/* Access to external PHY */
|
|
static int gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val)
|
|
{
|
|
int i;
|
|
|
|
gma_write16(hw, port, GM_SMI_DATA, val);
|
|
gma_write16(hw, port, GM_SMI_CTRL,
|
|
GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg));
|
|
|
|
for (i = 0; i < PHY_RETRIES; i++) {
|
|
if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
|
|
return 0;
|
|
udelay(1);
|
|
}
|
|
|
|
printk(KERN_WARNING PFX "%s: phy write timeout\n", hw->dev[port]->name);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val)
|
|
{
|
|
int i;
|
|
|
|
gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV)
|
|
| GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
|
|
|
|
for (i = 0; i < PHY_RETRIES; i++) {
|
|
if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL) {
|
|
*val = gma_read16(hw, port, GM_SMI_DATA);
|
|
return 0;
|
|
}
|
|
|
|
udelay(1);
|
|
}
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
|
|
{
|
|
u16 v;
|
|
|
|
if (__gm_phy_read(hw, port, reg, &v) != 0)
|
|
printk(KERN_WARNING PFX "%s: phy read timeout\n", hw->dev[port]->name);
|
|
return v;
|
|
}
|
|
|
|
static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
|
|
{
|
|
u16 power_control;
|
|
u32 reg1;
|
|
int vaux;
|
|
int ret = 0;
|
|
|
|
pr_debug("sky2_set_power_state %d\n", state);
|
|
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
|
|
|
|
power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_PMC);
|
|
vaux = (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
|
|
(power_control & PCI_PM_CAP_PME_D3cold);
|
|
|
|
power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL);
|
|
|
|
power_control |= PCI_PM_CTRL_PME_STATUS;
|
|
power_control &= ~(PCI_PM_CTRL_STATE_MASK);
|
|
|
|
switch (state) {
|
|
case PCI_D0:
|
|
/* switch power to VCC (WA for VAUX problem) */
|
|
sky2_write8(hw, B0_POWER_CTRL,
|
|
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
|
|
|
|
/* disable Core Clock Division, */
|
|
sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
|
|
/* enable bits are inverted */
|
|
sky2_write8(hw, B2_Y2_CLK_GATE,
|
|
Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
|
|
Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
|
|
Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
|
|
else
|
|
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
|
|
|
|
/* Turn off phy power saving */
|
|
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
|
|
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
|
|
|
|
/* looks like this XL is back asswards .. */
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) {
|
|
reg1 |= PCI_Y2_PHY1_COMA;
|
|
if (hw->ports > 1)
|
|
reg1 |= PCI_Y2_PHY2_COMA;
|
|
}
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
|
|
sky2_pci_write32(hw, PCI_DEV_REG3, 0);
|
|
reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
|
|
reg1 &= P_ASPM_CONTROL_MSK;
|
|
sky2_pci_write32(hw, PCI_DEV_REG4, reg1);
|
|
sky2_pci_write32(hw, PCI_DEV_REG5, 0);
|
|
}
|
|
|
|
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
|
|
|
|
break;
|
|
|
|
case PCI_D3hot:
|
|
case PCI_D3cold:
|
|
/* Turn on phy power saving */
|
|
reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
|
|
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
|
|
else
|
|
reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
|
|
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
|
|
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
|
|
else
|
|
/* enable bits are inverted */
|
|
sky2_write8(hw, B2_Y2_CLK_GATE,
|
|
Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
|
|
Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
|
|
Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
|
|
|
|
/* switch power to VAUX */
|
|
if (vaux && state != PCI_D3cold)
|
|
sky2_write8(hw, B0_POWER_CTRL,
|
|
(PC_VAUX_ENA | PC_VCC_ENA |
|
|
PC_VAUX_ON | PC_VCC_OFF));
|
|
break;
|
|
default:
|
|
printk(KERN_ERR PFX "Unknown power state %d\n", state);
|
|
ret = -1;
|
|
}
|
|
|
|
sky2_pci_write16(hw, hw->pm_cap + PCI_PM_CTRL, power_control);
|
|
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
|
|
return ret;
|
|
}
|
|
|
|
static void sky2_phy_reset(struct sky2_hw *hw, unsigned port)
|
|
{
|
|
u16 reg;
|
|
|
|
/* disable all GMAC IRQ's */
|
|
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
|
|
/* disable PHY IRQs */
|
|
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
|
|
|
|
gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
|
|
gma_write16(hw, port, GM_MC_ADDR_H2, 0);
|
|
gma_write16(hw, port, GM_MC_ADDR_H3, 0);
|
|
gma_write16(hw, port, GM_MC_ADDR_H4, 0);
|
|
|
|
reg = gma_read16(hw, port, GM_RX_CTRL);
|
|
reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA;
|
|
gma_write16(hw, port, GM_RX_CTRL, reg);
|
|
}
|
|
|
|
static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
|
|
u16 ctrl, ct1000, adv, pg, ledctrl, ledover;
|
|
|
|
if (sky2->autoneg == AUTONEG_ENABLE && hw->chip_id != CHIP_ID_YUKON_XL) {
|
|
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
|
|
|
|
ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
|
|
PHY_M_EC_MAC_S_MSK);
|
|
ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC)
|
|
ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA;
|
|
else
|
|
ectrl |= PHY_M_EC_M_DSC(2) | PHY_M_EC_S_DSC(3);
|
|
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
|
|
}
|
|
|
|
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
|
|
if (hw->copper) {
|
|
if (hw->chip_id == CHIP_ID_YUKON_FE) {
|
|
/* enable automatic crossover */
|
|
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
|
|
} else {
|
|
/* disable energy detect */
|
|
ctrl &= ~PHY_M_PC_EN_DET_MSK;
|
|
|
|
/* enable automatic crossover */
|
|
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
|
|
|
|
if (sky2->autoneg == AUTONEG_ENABLE &&
|
|
hw->chip_id == CHIP_ID_YUKON_XL) {
|
|
ctrl &= ~PHY_M_PC_DSC_MSK;
|
|
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
|
|
}
|
|
}
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
|
|
} else {
|
|
/* workaround for deviation #4.88 (CRC errors) */
|
|
/* disable Automatic Crossover */
|
|
|
|
ctrl &= ~PHY_M_PC_MDIX_MSK;
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL) {
|
|
/* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
|
|
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
|
|
ctrl &= ~PHY_M_MAC_MD_MSK;
|
|
ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
|
|
|
|
/* select page 1 to access Fiber registers */
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
|
|
}
|
|
}
|
|
|
|
ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
|
|
if (sky2->autoneg == AUTONEG_DISABLE)
|
|
ctrl &= ~PHY_CT_ANE;
|
|
else
|
|
ctrl |= PHY_CT_ANE;
|
|
|
|
ctrl |= PHY_CT_RESET;
|
|
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
|
|
|
|
ctrl = 0;
|
|
ct1000 = 0;
|
|
adv = PHY_AN_CSMA;
|
|
|
|
if (sky2->autoneg == AUTONEG_ENABLE) {
|
|
if (hw->copper) {
|
|
if (sky2->advertising & ADVERTISED_1000baseT_Full)
|
|
ct1000 |= PHY_M_1000C_AFD;
|
|
if (sky2->advertising & ADVERTISED_1000baseT_Half)
|
|
ct1000 |= PHY_M_1000C_AHD;
|
|
if (sky2->advertising & ADVERTISED_100baseT_Full)
|
|
adv |= PHY_M_AN_100_FD;
|
|
if (sky2->advertising & ADVERTISED_100baseT_Half)
|
|
adv |= PHY_M_AN_100_HD;
|
|
if (sky2->advertising & ADVERTISED_10baseT_Full)
|
|
adv |= PHY_M_AN_10_FD;
|
|
if (sky2->advertising & ADVERTISED_10baseT_Half)
|
|
adv |= PHY_M_AN_10_HD;
|
|
} else /* special defines for FIBER (88E1011S only) */
|
|
adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
|
|
|
|
/* Set Flow-control capabilities */
|
|
if (sky2->tx_pause && sky2->rx_pause)
|
|
adv |= PHY_AN_PAUSE_CAP; /* symmetric */
|
|
else if (sky2->rx_pause && !sky2->tx_pause)
|
|
adv |= PHY_AN_PAUSE_ASYM | PHY_AN_PAUSE_CAP;
|
|
else if (!sky2->rx_pause && sky2->tx_pause)
|
|
adv |= PHY_AN_PAUSE_ASYM; /* local */
|
|
|
|
/* Restart Auto-negotiation */
|
|
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
|
|
} else {
|
|
/* forced speed/duplex settings */
|
|
ct1000 = PHY_M_1000C_MSE;
|
|
|
|
if (sky2->duplex == DUPLEX_FULL)
|
|
ctrl |= PHY_CT_DUP_MD;
|
|
|
|
switch (sky2->speed) {
|
|
case SPEED_1000:
|
|
ctrl |= PHY_CT_SP1000;
|
|
break;
|
|
case SPEED_100:
|
|
ctrl |= PHY_CT_SP100;
|
|
break;
|
|
}
|
|
|
|
ctrl |= PHY_CT_RESET;
|
|
}
|
|
|
|
if (hw->chip_id != CHIP_ID_YUKON_FE)
|
|
gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
|
|
|
|
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
|
|
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
|
|
|
|
/* Setup Phy LED's */
|
|
ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
|
|
ledover = 0;
|
|
|
|
switch (hw->chip_id) {
|
|
case CHIP_ID_YUKON_FE:
|
|
/* on 88E3082 these bits are at 11..9 (shifted left) */
|
|
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
|
|
|
|
ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR);
|
|
|
|
/* delete ACT LED control bits */
|
|
ctrl &= ~PHY_M_FELP_LED1_MSK;
|
|
/* change ACT LED control to blink mode */
|
|
ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL);
|
|
gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl);
|
|
break;
|
|
|
|
case CHIP_ID_YUKON_XL:
|
|
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
|
|
|
|
/* select page 3 to access LED control register */
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
|
|
|
|
/* set LED Function Control register */
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
|
|
PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
|
|
PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
|
|
PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
|
|
|
|
/* set Polarity Control register */
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_STAT,
|
|
(PHY_M_POLC_LS1_P_MIX(4) |
|
|
PHY_M_POLC_IS0_P_MIX(4) |
|
|
PHY_M_POLC_LOS_CTRL(2) |
|
|
PHY_M_POLC_INIT_CTRL(2) |
|
|
PHY_M_POLC_STA1_CTRL(2) |
|
|
PHY_M_POLC_STA0_CTRL(2)));
|
|
|
|
/* restore page register */
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
|
|
break;
|
|
|
|
default:
|
|
/* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
|
|
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
|
|
/* turn off the Rx LED (LED_RX) */
|
|
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
|
|
}
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
|
|
/* apply fixes in PHY AFE */
|
|
gm_phy_write(hw, port, 22, 255);
|
|
/* increase differential signal amplitude in 10BASE-T */
|
|
gm_phy_write(hw, port, 24, 0xaa99);
|
|
gm_phy_write(hw, port, 23, 0x2011);
|
|
|
|
/* fix for IEEE A/B Symmetry failure in 1000BASE-T */
|
|
gm_phy_write(hw, port, 24, 0xa204);
|
|
gm_phy_write(hw, port, 23, 0x2002);
|
|
|
|
/* set page register to 0 */
|
|
gm_phy_write(hw, port, 22, 0);
|
|
} else {
|
|
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
|
|
|
|
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
|
|
/* turn on 100 Mbps LED (LED_LINK100) */
|
|
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
|
|
}
|
|
|
|
if (ledover)
|
|
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
|
|
|
|
}
|
|
/* Enable phy interrupt on auto-negotiation complete (or link up) */
|
|
if (sky2->autoneg == AUTONEG_ENABLE)
|
|
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
|
|
else
|
|
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
|
|
}
|
|
|
|
/* Force a renegotiation */
|
|
static void sky2_phy_reinit(struct sky2_port *sky2)
|
|
{
|
|
spin_lock_bh(&sky2->phy_lock);
|
|
sky2_phy_init(sky2->hw, sky2->port);
|
|
spin_unlock_bh(&sky2->phy_lock);
|
|
}
|
|
|
|
static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
|
|
u16 reg;
|
|
int i;
|
|
const u8 *addr = hw->dev[port]->dev_addr;
|
|
|
|
sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
|
|
sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR|GPC_ENA_PAUSE);
|
|
|
|
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) {
|
|
/* WA DEV_472 -- looks like crossed wires on port 2 */
|
|
/* clear GMAC 1 Control reset */
|
|
sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR);
|
|
do {
|
|
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET);
|
|
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR);
|
|
} while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL ||
|
|
gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 ||
|
|
gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
|
|
}
|
|
|
|
if (sky2->autoneg == AUTONEG_DISABLE) {
|
|
reg = gma_read16(hw, port, GM_GP_CTRL);
|
|
reg |= GM_GPCR_AU_ALL_DIS;
|
|
gma_write16(hw, port, GM_GP_CTRL, reg);
|
|
gma_read16(hw, port, GM_GP_CTRL);
|
|
|
|
switch (sky2->speed) {
|
|
case SPEED_1000:
|
|
reg &= ~GM_GPCR_SPEED_100;
|
|
reg |= GM_GPCR_SPEED_1000;
|
|
break;
|
|
case SPEED_100:
|
|
reg &= ~GM_GPCR_SPEED_1000;
|
|
reg |= GM_GPCR_SPEED_100;
|
|
break;
|
|
case SPEED_10:
|
|
reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
|
|
break;
|
|
}
|
|
|
|
if (sky2->duplex == DUPLEX_FULL)
|
|
reg |= GM_GPCR_DUP_FULL;
|
|
} else
|
|
reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
|
|
|
|
if (!sky2->tx_pause && !sky2->rx_pause) {
|
|
sky2_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
|
|
reg |=
|
|
GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
|
|
} else if (sky2->tx_pause && !sky2->rx_pause) {
|
|
/* disable Rx flow-control */
|
|
reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
|
|
}
|
|
|
|
gma_write16(hw, port, GM_GP_CTRL, reg);
|
|
|
|
sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
|
|
|
|
spin_lock_bh(&sky2->phy_lock);
|
|
sky2_phy_init(hw, port);
|
|
spin_unlock_bh(&sky2->phy_lock);
|
|
|
|
/* MIB clear */
|
|
reg = gma_read16(hw, port, GM_PHY_ADDR);
|
|
gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
|
|
|
|
for (i = GM_MIB_CNT_BASE; i <= GM_MIB_CNT_END; i += 4)
|
|
gma_read16(hw, port, i);
|
|
gma_write16(hw, port, GM_PHY_ADDR, reg);
|
|
|
|
/* transmit control */
|
|
gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
|
|
|
|
/* receive control reg: unicast + multicast + no FCS */
|
|
gma_write16(hw, port, GM_RX_CTRL,
|
|
GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
|
|
|
|
/* transmit flow control */
|
|
gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
|
|
|
|
/* transmit parameter */
|
|
gma_write16(hw, port, GM_TX_PARAM,
|
|
TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
|
|
TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
|
|
TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) |
|
|
TX_BACK_OFF_LIM(TX_BOF_LIM_DEF));
|
|
|
|
/* serial mode register */
|
|
reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
|
|
GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
|
|
|
|
if (hw->dev[port]->mtu > ETH_DATA_LEN)
|
|
reg |= GM_SMOD_JUMBO_ENA;
|
|
|
|
gma_write16(hw, port, GM_SERIAL_MODE, reg);
|
|
|
|
/* virtual address for data */
|
|
gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
|
|
|
|
/* physical address: used for pause frames */
|
|
gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
|
|
|
|
/* ignore counter overflows */
|
|
gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
|
|
gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
|
|
gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
|
|
|
|
/* Configure Rx MAC FIFO */
|
|
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
|
|
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T),
|
|
GMF_OPER_ON | GMF_RX_F_FL_ON);
|
|
|
|
/* Flush Rx MAC FIFO on any flow control or error */
|
|
sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR);
|
|
|
|
/* Set threshold to 0xa (64 bytes)
|
|
* ASF disabled so no need to do WA dev #4.30
|
|
*/
|
|
sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
|
|
|
|
/* Configure Tx MAC FIFO */
|
|
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
|
|
sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
|
|
sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
|
|
sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
|
|
if (hw->dev[port]->mtu > ETH_DATA_LEN) {
|
|
/* set Tx GMAC FIFO Almost Empty Threshold */
|
|
sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), 0x180);
|
|
/* Disable Store & Forward mode for TX */
|
|
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS);
|
|
}
|
|
}
|
|
|
|
}
|
|
|
|
/* Assign Ram Buffer allocation.
|
|
* start and end are in units of 4k bytes
|
|
* ram registers are in units of 64bit words
|
|
*/
|
|
static void sky2_ramset(struct sky2_hw *hw, u16 q, u8 startk, u8 endk)
|
|
{
|
|
u32 start, end;
|
|
|
|
start = startk * 4096/8;
|
|
end = (endk * 4096/8) - 1;
|
|
|
|
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
|
|
sky2_write32(hw, RB_ADDR(q, RB_START), start);
|
|
sky2_write32(hw, RB_ADDR(q, RB_END), end);
|
|
sky2_write32(hw, RB_ADDR(q, RB_WP), start);
|
|
sky2_write32(hw, RB_ADDR(q, RB_RP), start);
|
|
|
|
if (q == Q_R1 || q == Q_R2) {
|
|
u32 space = (endk - startk) * 4096/8;
|
|
u32 tp = space - space/4;
|
|
|
|
/* On receive queue's set the thresholds
|
|
* give receiver priority when > 3/4 full
|
|
* send pause when down to 2K
|
|
*/
|
|
sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp);
|
|
sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2);
|
|
|
|
tp = space - 2048/8;
|
|
sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp);
|
|
sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4);
|
|
} else {
|
|
/* Enable store & forward on Tx queue's because
|
|
* Tx FIFO is only 1K on Yukon
|
|
*/
|
|
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
|
|
}
|
|
|
|
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
|
|
sky2_read8(hw, RB_ADDR(q, RB_CTRL));
|
|
}
|
|
|
|
/* Setup Bus Memory Interface */
|
|
static void sky2_qset(struct sky2_hw *hw, u16 q)
|
|
{
|
|
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET);
|
|
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT);
|
|
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON);
|
|
sky2_write32(hw, Q_ADDR(q, Q_WM), BMU_WM_DEFAULT);
|
|
}
|
|
|
|
/* Setup prefetch unit registers. This is the interface between
|
|
* hardware and driver list elements
|
|
*/
|
|
static void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr,
|
|
u64 addr, u32 last)
|
|
{
|
|
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
|
|
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR);
|
|
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), addr >> 32);
|
|
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), (u32) addr);
|
|
sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last);
|
|
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON);
|
|
|
|
sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL));
|
|
}
|
|
|
|
static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod;
|
|
|
|
sky2->tx_prod = (sky2->tx_prod + 1) % TX_RING_SIZE;
|
|
return le;
|
|
}
|
|
|
|
/* Update chip's next pointer */
|
|
static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx)
|
|
{
|
|
wmb();
|
|
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
|
|
mmiowb();
|
|
}
|
|
|
|
|
|
static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put;
|
|
sky2->rx_put = (sky2->rx_put + 1) % RX_LE_SIZE;
|
|
return le;
|
|
}
|
|
|
|
/* Return high part of DMA address (could be 32 or 64 bit) */
|
|
static inline u32 high32(dma_addr_t a)
|
|
{
|
|
return sizeof(a) > sizeof(u32) ? (a >> 16) >> 16 : 0;
|
|
}
|
|
|
|
/* Build description to hardware about buffer */
|
|
static void sky2_rx_add(struct sky2_port *sky2, dma_addr_t map)
|
|
{
|
|
struct sky2_rx_le *le;
|
|
u32 hi = high32(map);
|
|
u16 len = sky2->rx_bufsize;
|
|
|
|
if (sky2->rx_addr64 != hi) {
|
|
le = sky2_next_rx(sky2);
|
|
le->addr = cpu_to_le32(hi);
|
|
le->ctrl = 0;
|
|
le->opcode = OP_ADDR64 | HW_OWNER;
|
|
sky2->rx_addr64 = high32(map + len);
|
|
}
|
|
|
|
le = sky2_next_rx(sky2);
|
|
le->addr = cpu_to_le32((u32) map);
|
|
le->length = cpu_to_le16(len);
|
|
le->ctrl = 0;
|
|
le->opcode = OP_PACKET | HW_OWNER;
|
|
}
|
|
|
|
|
|
/* Tell chip where to start receive checksum.
|
|
* Actually has two checksums, but set both same to avoid possible byte
|
|
* order problems.
|
|
*/
|
|
static void rx_set_checksum(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_rx_le *le;
|
|
|
|
le = sky2_next_rx(sky2);
|
|
le->addr = (ETH_HLEN << 16) | ETH_HLEN;
|
|
le->ctrl = 0;
|
|
le->opcode = OP_TCPSTART | HW_OWNER;
|
|
|
|
sky2_write32(sky2->hw,
|
|
Q_ADDR(rxqaddr[sky2->port], Q_CSR),
|
|
sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
|
|
|
|
}
|
|
|
|
/*
|
|
* The RX Stop command will not work for Yukon-2 if the BMU does not
|
|
* reach the end of packet and since we can't make sure that we have
|
|
* incoming data, we must reset the BMU while it is not doing a DMA
|
|
* transfer. Since it is possible that the RX path is still active,
|
|
* the RX RAM buffer will be stopped first, so any possible incoming
|
|
* data will not trigger a DMA. After the RAM buffer is stopped, the
|
|
* BMU is polled until any DMA in progress is ended and only then it
|
|
* will be reset.
|
|
*/
|
|
static void sky2_rx_stop(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned rxq = rxqaddr[sky2->port];
|
|
int i;
|
|
|
|
/* disable the RAM Buffer receive queue */
|
|
sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD);
|
|
|
|
for (i = 0; i < 0xffff; i++)
|
|
if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL))
|
|
== sky2_read8(hw, RB_ADDR(rxq, Q_RL)))
|
|
goto stopped;
|
|
|
|
printk(KERN_WARNING PFX "%s: receiver stop failed\n",
|
|
sky2->netdev->name);
|
|
stopped:
|
|
sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST);
|
|
|
|
/* reset the Rx prefetch unit */
|
|
sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
|
|
}
|
|
|
|
/* Clean out receive buffer area, assumes receiver hardware stopped */
|
|
static void sky2_rx_clean(struct sky2_port *sky2)
|
|
{
|
|
unsigned i;
|
|
|
|
memset(sky2->rx_le, 0, RX_LE_BYTES);
|
|
for (i = 0; i < sky2->rx_pending; i++) {
|
|
struct ring_info *re = sky2->rx_ring + i;
|
|
|
|
if (re->skb) {
|
|
pci_unmap_single(sky2->hw->pdev,
|
|
re->mapaddr, sky2->rx_bufsize,
|
|
PCI_DMA_FROMDEVICE);
|
|
kfree_skb(re->skb);
|
|
re->skb = NULL;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Basic MII support */
|
|
static int sky2_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
|
|
{
|
|
struct mii_ioctl_data *data = if_mii(ifr);
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
int err = -EOPNOTSUPP;
|
|
|
|
if (!netif_running(dev))
|
|
return -ENODEV; /* Phy still in reset */
|
|
|
|
switch (cmd) {
|
|
case SIOCGMIIPHY:
|
|
data->phy_id = PHY_ADDR_MARV;
|
|
|
|
/* fallthru */
|
|
case SIOCGMIIREG: {
|
|
u16 val = 0;
|
|
|
|
spin_lock_bh(&sky2->phy_lock);
|
|
err = __gm_phy_read(hw, sky2->port, data->reg_num & 0x1f, &val);
|
|
spin_unlock_bh(&sky2->phy_lock);
|
|
|
|
data->val_out = val;
|
|
break;
|
|
}
|
|
|
|
case SIOCSMIIREG:
|
|
if (!capable(CAP_NET_ADMIN))
|
|
return -EPERM;
|
|
|
|
spin_lock_bh(&sky2->phy_lock);
|
|
err = gm_phy_write(hw, sky2->port, data->reg_num & 0x1f,
|
|
data->val_in);
|
|
spin_unlock_bh(&sky2->phy_lock);
|
|
break;
|
|
}
|
|
return err;
|
|
}
|
|
|
|
#ifdef SKY2_VLAN_TAG_USED
|
|
static void sky2_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
u16 port = sky2->port;
|
|
|
|
spin_lock_bh(&sky2->tx_lock);
|
|
|
|
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_ON);
|
|
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_ON);
|
|
sky2->vlgrp = grp;
|
|
|
|
spin_unlock_bh(&sky2->tx_lock);
|
|
}
|
|
|
|
static void sky2_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
u16 port = sky2->port;
|
|
|
|
spin_lock_bh(&sky2->tx_lock);
|
|
|
|
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_OFF);
|
|
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_OFF);
|
|
if (sky2->vlgrp)
|
|
sky2->vlgrp->vlan_devices[vid] = NULL;
|
|
|
|
spin_unlock_bh(&sky2->tx_lock);
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* It appears the hardware has a bug in the FIFO logic that
|
|
* cause it to hang if the FIFO gets overrun and the receive buffer
|
|
* is not aligned. ALso alloc_skb() won't align properly if slab
|
|
* debugging is enabled.
|
|
*/
|
|
static inline struct sk_buff *sky2_alloc_skb(unsigned int size, gfp_t gfp_mask)
|
|
{
|
|
struct sk_buff *skb;
|
|
|
|
skb = alloc_skb(size + RX_SKB_ALIGN, gfp_mask);
|
|
if (likely(skb)) {
|
|
unsigned long p = (unsigned long) skb->data;
|
|
skb_reserve(skb,
|
|
((p + RX_SKB_ALIGN - 1) & ~(RX_SKB_ALIGN - 1)) - p);
|
|
}
|
|
|
|
return skb;
|
|
}
|
|
|
|
/*
|
|
* Allocate and setup receiver buffer pool.
|
|
* In case of 64 bit dma, there are 2X as many list elements
|
|
* available as ring entries
|
|
* and need to reserve one list element so we don't wrap around.
|
|
*/
|
|
static int sky2_rx_start(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned rxq = rxqaddr[sky2->port];
|
|
int i;
|
|
|
|
sky2->rx_put = sky2->rx_next = 0;
|
|
sky2_qset(hw, rxq);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
|
|
/* MAC Rx RAM Read is controlled by hardware */
|
|
sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
|
|
}
|
|
|
|
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
|
|
|
|
rx_set_checksum(sky2);
|
|
for (i = 0; i < sky2->rx_pending; i++) {
|
|
struct ring_info *re = sky2->rx_ring + i;
|
|
|
|
re->skb = sky2_alloc_skb(sky2->rx_bufsize, GFP_KERNEL);
|
|
if (!re->skb)
|
|
goto nomem;
|
|
|
|
re->mapaddr = pci_map_single(hw->pdev, re->skb->data,
|
|
sky2->rx_bufsize, PCI_DMA_FROMDEVICE);
|
|
sky2_rx_add(sky2, re->mapaddr);
|
|
}
|
|
|
|
/* Truncate oversize frames */
|
|
sky2_write16(hw, SK_REG(sky2->port, RX_GMF_TR_THR), sky2->rx_bufsize - 8);
|
|
sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON);
|
|
|
|
/* Tell chip about available buffers */
|
|
sky2_write16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX), sky2->rx_put);
|
|
return 0;
|
|
nomem:
|
|
sky2_rx_clean(sky2);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
/* Bring up network interface. */
|
|
static int sky2_up(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
u32 ramsize, rxspace, imask;
|
|
int err = -ENOMEM;
|
|
|
|
if (netif_msg_ifup(sky2))
|
|
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
|
|
|
|
/* must be power of 2 */
|
|
sky2->tx_le = pci_alloc_consistent(hw->pdev,
|
|
TX_RING_SIZE *
|
|
sizeof(struct sky2_tx_le),
|
|
&sky2->tx_le_map);
|
|
if (!sky2->tx_le)
|
|
goto err_out;
|
|
|
|
sky2->tx_ring = kcalloc(TX_RING_SIZE, sizeof(struct tx_ring_info),
|
|
GFP_KERNEL);
|
|
if (!sky2->tx_ring)
|
|
goto err_out;
|
|
sky2->tx_prod = sky2->tx_cons = 0;
|
|
|
|
sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES,
|
|
&sky2->rx_le_map);
|
|
if (!sky2->rx_le)
|
|
goto err_out;
|
|
memset(sky2->rx_le, 0, RX_LE_BYTES);
|
|
|
|
sky2->rx_ring = kcalloc(sky2->rx_pending, sizeof(struct ring_info),
|
|
GFP_KERNEL);
|
|
if (!sky2->rx_ring)
|
|
goto err_out;
|
|
|
|
sky2_mac_init(hw, port);
|
|
|
|
/* Determine available ram buffer space (in 4K blocks).
|
|
* Note: not sure about the FE setting below yet
|
|
*/
|
|
if (hw->chip_id == CHIP_ID_YUKON_FE)
|
|
ramsize = 4;
|
|
else
|
|
ramsize = sky2_read8(hw, B2_E_0);
|
|
|
|
/* Give transmitter one third (rounded up) */
|
|
rxspace = ramsize - (ramsize + 2) / 3;
|
|
|
|
sky2_ramset(hw, rxqaddr[port], 0, rxspace);
|
|
sky2_ramset(hw, txqaddr[port], rxspace, ramsize);
|
|
|
|
/* Make sure SyncQ is disabled */
|
|
sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
|
|
RB_RST_SET);
|
|
|
|
sky2_qset(hw, txqaddr[port]);
|
|
|
|
/* Set almost empty threshold */
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
|
|
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
|
|
|
|
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
|
|
TX_RING_SIZE - 1);
|
|
|
|
err = sky2_rx_start(sky2);
|
|
if (err)
|
|
goto err_out;
|
|
|
|
/* Enable interrupts from phy/mac for port */
|
|
imask = sky2_read32(hw, B0_IMSK);
|
|
imask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
|
|
sky2_write32(hw, B0_IMSK, imask);
|
|
|
|
return 0;
|
|
|
|
err_out:
|
|
if (sky2->rx_le) {
|
|
pci_free_consistent(hw->pdev, RX_LE_BYTES,
|
|
sky2->rx_le, sky2->rx_le_map);
|
|
sky2->rx_le = NULL;
|
|
}
|
|
if (sky2->tx_le) {
|
|
pci_free_consistent(hw->pdev,
|
|
TX_RING_SIZE * sizeof(struct sky2_tx_le),
|
|
sky2->tx_le, sky2->tx_le_map);
|
|
sky2->tx_le = NULL;
|
|
}
|
|
kfree(sky2->tx_ring);
|
|
kfree(sky2->rx_ring);
|
|
|
|
sky2->tx_ring = NULL;
|
|
sky2->rx_ring = NULL;
|
|
return err;
|
|
}
|
|
|
|
/* Modular subtraction in ring */
|
|
static inline int tx_dist(unsigned tail, unsigned head)
|
|
{
|
|
return (head - tail) % TX_RING_SIZE;
|
|
}
|
|
|
|
/* Number of list elements available for next tx */
|
|
static inline int tx_avail(const struct sky2_port *sky2)
|
|
{
|
|
return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod);
|
|
}
|
|
|
|
/* Estimate of number of transmit list elements required */
|
|
static unsigned tx_le_req(const struct sk_buff *skb)
|
|
{
|
|
unsigned count;
|
|
|
|
count = sizeof(dma_addr_t) / sizeof(u32);
|
|
count += skb_shinfo(skb)->nr_frags * count;
|
|
|
|
if (skb_shinfo(skb)->tso_size)
|
|
++count;
|
|
|
|
if (skb->ip_summed == CHECKSUM_HW)
|
|
++count;
|
|
|
|
return count;
|
|
}
|
|
|
|
/*
|
|
* Put one packet in ring for transmit.
|
|
* A single packet can generate multiple list elements, and
|
|
* the number of ring elements will probably be less than the number
|
|
* of list elements used.
|
|
*
|
|
* No BH disabling for tx_lock here (like tg3)
|
|
*/
|
|
static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
struct sky2_tx_le *le = NULL;
|
|
struct tx_ring_info *re;
|
|
unsigned i, len;
|
|
int avail;
|
|
dma_addr_t mapping;
|
|
u32 addr64;
|
|
u16 mss;
|
|
u8 ctrl;
|
|
|
|
/* No BH disabling for tx_lock here. We are running in BH disabled
|
|
* context and TX reclaim runs via poll inside of a software
|
|
* interrupt, and no related locks in IRQ processing.
|
|
*/
|
|
if (!spin_trylock(&sky2->tx_lock))
|
|
return NETDEV_TX_LOCKED;
|
|
|
|
if (unlikely(tx_avail(sky2) < tx_le_req(skb))) {
|
|
/* There is a known but harmless race with lockless tx
|
|
* and netif_stop_queue.
|
|
*/
|
|
if (!netif_queue_stopped(dev)) {
|
|
netif_stop_queue(dev);
|
|
if (net_ratelimit())
|
|
printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
|
|
dev->name);
|
|
}
|
|
spin_unlock(&sky2->tx_lock);
|
|
|
|
return NETDEV_TX_BUSY;
|
|
}
|
|
|
|
if (unlikely(netif_msg_tx_queued(sky2)))
|
|
printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n",
|
|
dev->name, sky2->tx_prod, skb->len);
|
|
|
|
len = skb_headlen(skb);
|
|
mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
|
|
addr64 = high32(mapping);
|
|
|
|
re = sky2->tx_ring + sky2->tx_prod;
|
|
|
|
/* Send high bits if changed or crosses boundary */
|
|
if (addr64 != sky2->tx_addr64 || high32(mapping + len) != sky2->tx_addr64) {
|
|
le = get_tx_le(sky2);
|
|
le->tx.addr = cpu_to_le32(addr64);
|
|
le->ctrl = 0;
|
|
le->opcode = OP_ADDR64 | HW_OWNER;
|
|
sky2->tx_addr64 = high32(mapping + len);
|
|
}
|
|
|
|
/* Check for TCP Segmentation Offload */
|
|
mss = skb_shinfo(skb)->tso_size;
|
|
if (mss != 0) {
|
|
/* just drop the packet if non-linear expansion fails */
|
|
if (skb_header_cloned(skb) &&
|
|
pskb_expand_head(skb, 0, 0, GFP_ATOMIC)) {
|
|
dev_kfree_skb(skb);
|
|
goto out_unlock;
|
|
}
|
|
|
|
mss += ((skb->h.th->doff - 5) * 4); /* TCP options */
|
|
mss += (skb->nh.iph->ihl * 4) + sizeof(struct tcphdr);
|
|
mss += ETH_HLEN;
|
|
}
|
|
|
|
if (mss != sky2->tx_last_mss) {
|
|
le = get_tx_le(sky2);
|
|
le->tx.tso.size = cpu_to_le16(mss);
|
|
le->tx.tso.rsvd = 0;
|
|
le->opcode = OP_LRGLEN | HW_OWNER;
|
|
le->ctrl = 0;
|
|
sky2->tx_last_mss = mss;
|
|
}
|
|
|
|
ctrl = 0;
|
|
#ifdef SKY2_VLAN_TAG_USED
|
|
/* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */
|
|
if (sky2->vlgrp && vlan_tx_tag_present(skb)) {
|
|
if (!le) {
|
|
le = get_tx_le(sky2);
|
|
le->tx.addr = 0;
|
|
le->opcode = OP_VLAN|HW_OWNER;
|
|
le->ctrl = 0;
|
|
} else
|
|
le->opcode |= OP_VLAN;
|
|
le->length = cpu_to_be16(vlan_tx_tag_get(skb));
|
|
ctrl |= INS_VLAN;
|
|
}
|
|
#endif
|
|
|
|
/* Handle TCP checksum offload */
|
|
if (skb->ip_summed == CHECKSUM_HW) {
|
|
u16 hdr = skb->h.raw - skb->data;
|
|
u16 offset = hdr + skb->csum;
|
|
|
|
ctrl = CALSUM | WR_SUM | INIT_SUM | LOCK_SUM;
|
|
if (skb->nh.iph->protocol == IPPROTO_UDP)
|
|
ctrl |= UDPTCP;
|
|
|
|
le = get_tx_le(sky2);
|
|
le->tx.csum.start = cpu_to_le16(hdr);
|
|
le->tx.csum.offset = cpu_to_le16(offset);
|
|
le->length = 0; /* initial checksum value */
|
|
le->ctrl = 1; /* one packet */
|
|
le->opcode = OP_TCPLISW | HW_OWNER;
|
|
}
|
|
|
|
le = get_tx_le(sky2);
|
|
le->tx.addr = cpu_to_le32((u32) mapping);
|
|
le->length = cpu_to_le16(len);
|
|
le->ctrl = ctrl;
|
|
le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER);
|
|
|
|
/* Record the transmit mapping info */
|
|
re->skb = skb;
|
|
pci_unmap_addr_set(re, mapaddr, mapping);
|
|
|
|
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
|
|
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
|
|
struct tx_ring_info *fre;
|
|
|
|
mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
|
|
frag->size, PCI_DMA_TODEVICE);
|
|
addr64 = high32(mapping);
|
|
if (addr64 != sky2->tx_addr64) {
|
|
le = get_tx_le(sky2);
|
|
le->tx.addr = cpu_to_le32(addr64);
|
|
le->ctrl = 0;
|
|
le->opcode = OP_ADDR64 | HW_OWNER;
|
|
sky2->tx_addr64 = addr64;
|
|
}
|
|
|
|
le = get_tx_le(sky2);
|
|
le->tx.addr = cpu_to_le32((u32) mapping);
|
|
le->length = cpu_to_le16(frag->size);
|
|
le->ctrl = ctrl;
|
|
le->opcode = OP_BUFFER | HW_OWNER;
|
|
|
|
fre = sky2->tx_ring
|
|
+ ((re - sky2->tx_ring) + i + 1) % TX_RING_SIZE;
|
|
pci_unmap_addr_set(fre, mapaddr, mapping);
|
|
}
|
|
|
|
re->idx = sky2->tx_prod;
|
|
le->ctrl |= EOP;
|
|
|
|
avail = tx_avail(sky2);
|
|
if (mss != 0 || avail < TX_MIN_PENDING) {
|
|
le->ctrl |= FRC_STAT;
|
|
if (avail <= MAX_SKB_TX_LE)
|
|
netif_stop_queue(dev);
|
|
}
|
|
|
|
sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod);
|
|
|
|
out_unlock:
|
|
spin_unlock(&sky2->tx_lock);
|
|
|
|
dev->trans_start = jiffies;
|
|
return NETDEV_TX_OK;
|
|
}
|
|
|
|
/*
|
|
* Free ring elements from starting at tx_cons until "done"
|
|
*
|
|
* NB: the hardware will tell us about partial completion of multi-part
|
|
* buffers; these are deferred until completion.
|
|
*/
|
|
static void sky2_tx_complete(struct sky2_port *sky2, u16 done)
|
|
{
|
|
struct net_device *dev = sky2->netdev;
|
|
struct pci_dev *pdev = sky2->hw->pdev;
|
|
u16 nxt, put;
|
|
unsigned i;
|
|
|
|
BUG_ON(done >= TX_RING_SIZE);
|
|
|
|
if (unlikely(netif_msg_tx_done(sky2)))
|
|
printk(KERN_DEBUG "%s: tx done, up to %u\n",
|
|
dev->name, done);
|
|
|
|
for (put = sky2->tx_cons; put != done; put = nxt) {
|
|
struct tx_ring_info *re = sky2->tx_ring + put;
|
|
struct sk_buff *skb = re->skb;
|
|
|
|
nxt = re->idx;
|
|
BUG_ON(nxt >= TX_RING_SIZE);
|
|
prefetch(sky2->tx_ring + nxt);
|
|
|
|
/* Check for partial status */
|
|
if (tx_dist(put, done) < tx_dist(put, nxt))
|
|
break;
|
|
|
|
skb = re->skb;
|
|
pci_unmap_single(pdev, pci_unmap_addr(re, mapaddr),
|
|
skb_headlen(skb), PCI_DMA_TODEVICE);
|
|
|
|
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
|
|
struct tx_ring_info *fre;
|
|
fre = sky2->tx_ring + (put + i + 1) % TX_RING_SIZE;
|
|
pci_unmap_page(pdev, pci_unmap_addr(fre, mapaddr),
|
|
skb_shinfo(skb)->frags[i].size,
|
|
PCI_DMA_TODEVICE);
|
|
}
|
|
|
|
dev_kfree_skb(skb);
|
|
}
|
|
|
|
sky2->tx_cons = put;
|
|
if (tx_avail(sky2) > MAX_SKB_TX_LE)
|
|
netif_wake_queue(dev);
|
|
}
|
|
|
|
/* Cleanup all untransmitted buffers, assume transmitter not running */
|
|
static void sky2_tx_clean(struct sky2_port *sky2)
|
|
{
|
|
spin_lock_bh(&sky2->tx_lock);
|
|
sky2_tx_complete(sky2, sky2->tx_prod);
|
|
spin_unlock_bh(&sky2->tx_lock);
|
|
}
|
|
|
|
/* Network shutdown */
|
|
static int sky2_down(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
u16 ctrl;
|
|
u32 imask;
|
|
|
|
/* Never really got started! */
|
|
if (!sky2->tx_le)
|
|
return 0;
|
|
|
|
if (netif_msg_ifdown(sky2))
|
|
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
|
|
|
|
/* Stop more packets from being queued */
|
|
netif_stop_queue(dev);
|
|
|
|
sky2_phy_reset(hw, port);
|
|
|
|
/* Stop transmitter */
|
|
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
|
|
sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR));
|
|
|
|
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
|
|
RB_RST_SET | RB_DIS_OP_MD);
|
|
|
|
ctrl = gma_read16(hw, port, GM_GP_CTRL);
|
|
ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA);
|
|
gma_write16(hw, port, GM_GP_CTRL, ctrl);
|
|
|
|
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
|
|
|
|
/* Workaround shared GMAC reset */
|
|
if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
|
|
&& port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
|
|
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
|
|
|
|
/* Disable Force Sync bit and Enable Alloc bit */
|
|
sky2_write8(hw, SK_REG(port, TXA_CTRL),
|
|
TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
|
|
|
|
/* Stop Interval Timer and Limit Counter of Tx Arbiter */
|
|
sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L);
|
|
sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L);
|
|
|
|
/* Reset the PCI FIFO of the async Tx queue */
|
|
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR),
|
|
BMU_RST_SET | BMU_FIFO_RST);
|
|
|
|
/* Reset the Tx prefetch units */
|
|
sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL),
|
|
PREF_UNIT_RST_SET);
|
|
|
|
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
|
|
|
|
sky2_rx_stop(sky2);
|
|
|
|
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
|
|
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
|
|
|
|
/* Disable port IRQ */
|
|
imask = sky2_read32(hw, B0_IMSK);
|
|
imask &= ~(sky2->port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
|
|
sky2_write32(hw, B0_IMSK, imask);
|
|
|
|
/* turn off LED's */
|
|
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
|
|
|
|
synchronize_irq(hw->pdev->irq);
|
|
|
|
sky2_tx_clean(sky2);
|
|
sky2_rx_clean(sky2);
|
|
|
|
pci_free_consistent(hw->pdev, RX_LE_BYTES,
|
|
sky2->rx_le, sky2->rx_le_map);
|
|
kfree(sky2->rx_ring);
|
|
|
|
pci_free_consistent(hw->pdev,
|
|
TX_RING_SIZE * sizeof(struct sky2_tx_le),
|
|
sky2->tx_le, sky2->tx_le_map);
|
|
kfree(sky2->tx_ring);
|
|
|
|
sky2->tx_le = NULL;
|
|
sky2->rx_le = NULL;
|
|
|
|
sky2->rx_ring = NULL;
|
|
sky2->tx_ring = NULL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
|
|
{
|
|
if (!hw->copper)
|
|
return SPEED_1000;
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_FE)
|
|
return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10;
|
|
|
|
switch (aux & PHY_M_PS_SPEED_MSK) {
|
|
case PHY_M_PS_SPEED_1000:
|
|
return SPEED_1000;
|
|
case PHY_M_PS_SPEED_100:
|
|
return SPEED_100;
|
|
default:
|
|
return SPEED_10;
|
|
}
|
|
}
|
|
|
|
static void sky2_link_up(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
u16 reg;
|
|
|
|
/* Enable Transmit FIFO Underrun */
|
|
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
|
|
|
|
reg = gma_read16(hw, port, GM_GP_CTRL);
|
|
if (sky2->autoneg == AUTONEG_DISABLE) {
|
|
reg |= GM_GPCR_AU_ALL_DIS;
|
|
|
|
/* Is write/read necessary? Copied from sky2_mac_init */
|
|
gma_write16(hw, port, GM_GP_CTRL, reg);
|
|
gma_read16(hw, port, GM_GP_CTRL);
|
|
|
|
switch (sky2->speed) {
|
|
case SPEED_1000:
|
|
reg &= ~GM_GPCR_SPEED_100;
|
|
reg |= GM_GPCR_SPEED_1000;
|
|
break;
|
|
case SPEED_100:
|
|
reg &= ~GM_GPCR_SPEED_1000;
|
|
reg |= GM_GPCR_SPEED_100;
|
|
break;
|
|
case SPEED_10:
|
|
reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
|
|
break;
|
|
}
|
|
} else
|
|
reg &= ~GM_GPCR_AU_ALL_DIS;
|
|
|
|
if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
|
|
reg |= GM_GPCR_DUP_FULL;
|
|
|
|
/* enable Rx/Tx */
|
|
reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
|
|
gma_write16(hw, port, GM_GP_CTRL, reg);
|
|
gma_read16(hw, port, GM_GP_CTRL);
|
|
|
|
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
|
|
|
|
netif_carrier_on(sky2->netdev);
|
|
netif_wake_queue(sky2->netdev);
|
|
|
|
/* Turn on link LED */
|
|
sky2_write8(hw, SK_REG(port, LNK_LED_REG),
|
|
LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL) {
|
|
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
|
|
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
|
|
PHY_M_LEDC_INIT_CTRL(sky2->speed ==
|
|
SPEED_10 ? 7 : 0) |
|
|
PHY_M_LEDC_STA1_CTRL(sky2->speed ==
|
|
SPEED_100 ? 7 : 0) |
|
|
PHY_M_LEDC_STA0_CTRL(sky2->speed ==
|
|
SPEED_1000 ? 7 : 0));
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
|
|
}
|
|
|
|
if (netif_msg_link(sky2))
|
|
printk(KERN_INFO PFX
|
|
"%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
|
|
sky2->netdev->name, sky2->speed,
|
|
sky2->duplex == DUPLEX_FULL ? "full" : "half",
|
|
(sky2->tx_pause && sky2->rx_pause) ? "both" :
|
|
sky2->tx_pause ? "tx" : sky2->rx_pause ? "rx" : "none");
|
|
}
|
|
|
|
static void sky2_link_down(struct sky2_port *sky2)
|
|
{
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
u16 reg;
|
|
|
|
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
|
|
|
|
reg = gma_read16(hw, port, GM_GP_CTRL);
|
|
reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
|
|
gma_write16(hw, port, GM_GP_CTRL, reg);
|
|
gma_read16(hw, port, GM_GP_CTRL); /* PCI post */
|
|
|
|
if (sky2->rx_pause && !sky2->tx_pause) {
|
|
/* restore Asymmetric Pause bit */
|
|
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
|
|
gm_phy_read(hw, port, PHY_MARV_AUNE_ADV)
|
|
| PHY_M_AN_ASP);
|
|
}
|
|
|
|
netif_carrier_off(sky2->netdev);
|
|
netif_stop_queue(sky2->netdev);
|
|
|
|
/* Turn on link LED */
|
|
sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
|
|
|
|
if (netif_msg_link(sky2))
|
|
printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name);
|
|
sky2_phy_init(hw, port);
|
|
}
|
|
|
|
static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
|
|
{
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
u16 lpa;
|
|
|
|
lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
|
|
|
|
if (lpa & PHY_M_AN_RF) {
|
|
printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
|
|
return -1;
|
|
}
|
|
|
|
if (hw->chip_id != CHIP_ID_YUKON_FE &&
|
|
gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
|
|
printk(KERN_ERR PFX "%s: master/slave fault",
|
|
sky2->netdev->name);
|
|
return -1;
|
|
}
|
|
|
|
if (!(aux & PHY_M_PS_SPDUP_RES)) {
|
|
printk(KERN_ERR PFX "%s: speed/duplex mismatch",
|
|
sky2->netdev->name);
|
|
return -1;
|
|
}
|
|
|
|
sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
|
|
|
|
sky2->speed = sky2_phy_speed(hw, aux);
|
|
|
|
/* Pause bits are offset (9..8) */
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL)
|
|
aux >>= 6;
|
|
|
|
sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
|
|
sky2->tx_pause = (aux & PHY_M_PS_TX_P_EN) != 0;
|
|
|
|
if ((sky2->tx_pause || sky2->rx_pause)
|
|
&& !(sky2->speed < SPEED_1000 && sky2->duplex == DUPLEX_HALF))
|
|
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
|
|
else
|
|
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Interrupt from PHY */
|
|
static void sky2_phy_intr(struct sky2_hw *hw, unsigned port)
|
|
{
|
|
struct net_device *dev = hw->dev[port];
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
u16 istatus, phystat;
|
|
|
|
spin_lock(&sky2->phy_lock);
|
|
istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT);
|
|
phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
|
|
|
|
if (!netif_running(dev))
|
|
goto out;
|
|
|
|
if (netif_msg_intr(sky2))
|
|
printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
|
|
sky2->netdev->name, istatus, phystat);
|
|
|
|
if (istatus & PHY_M_IS_AN_COMPL) {
|
|
if (sky2_autoneg_done(sky2, phystat) == 0)
|
|
sky2_link_up(sky2);
|
|
goto out;
|
|
}
|
|
|
|
if (istatus & PHY_M_IS_LSP_CHANGE)
|
|
sky2->speed = sky2_phy_speed(hw, phystat);
|
|
|
|
if (istatus & PHY_M_IS_DUP_CHANGE)
|
|
sky2->duplex =
|
|
(phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
|
|
|
|
if (istatus & PHY_M_IS_LST_CHANGE) {
|
|
if (phystat & PHY_M_PS_LINK_UP)
|
|
sky2_link_up(sky2);
|
|
else
|
|
sky2_link_down(sky2);
|
|
}
|
|
out:
|
|
spin_unlock(&sky2->phy_lock);
|
|
}
|
|
|
|
|
|
/* Transmit timeout is only called if we are running, carries is up
|
|
* and tx queue is full (stopped).
|
|
*/
|
|
static void sky2_tx_timeout(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned txq = txqaddr[sky2->port];
|
|
u16 report, done;
|
|
|
|
if (netif_msg_timer(sky2))
|
|
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
|
|
|
|
report = sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX);
|
|
done = sky2_read16(hw, Q_ADDR(txq, Q_DONE));
|
|
|
|
printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n",
|
|
dev->name,
|
|
sky2->tx_cons, sky2->tx_prod, report, done);
|
|
|
|
if (report != done) {
|
|
printk(KERN_INFO PFX "status burst pending (irq moderation?)\n");
|
|
|
|
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
|
|
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
|
|
} else if (report != sky2->tx_cons) {
|
|
printk(KERN_INFO PFX "status report lost?\n");
|
|
|
|
spin_lock_bh(&sky2->tx_lock);
|
|
sky2_tx_complete(sky2, report);
|
|
spin_unlock_bh(&sky2->tx_lock);
|
|
} else {
|
|
printk(KERN_INFO PFX "hardware hung? flushing\n");
|
|
|
|
sky2_write32(hw, Q_ADDR(txq, Q_CSR), BMU_STOP);
|
|
sky2_write32(hw, Y2_QADDR(txq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
|
|
|
|
sky2_tx_clean(sky2);
|
|
|
|
sky2_qset(hw, txq);
|
|
sky2_prefetch_init(hw, txq, sky2->tx_le_map, TX_RING_SIZE - 1);
|
|
}
|
|
}
|
|
|
|
|
|
#define roundup(x, y) ((((x)+((y)-1))/(y))*(y))
|
|
/* Want receive buffer size to be multiple of 64 bits
|
|
* and incl room for vlan and truncation
|
|
*/
|
|
static inline unsigned sky2_buf_size(int mtu)
|
|
{
|
|
return roundup(mtu + ETH_HLEN + VLAN_HLEN, 8) + 8;
|
|
}
|
|
|
|
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
int err;
|
|
u16 ctl, mode;
|
|
u32 imask;
|
|
|
|
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
|
|
return -EINVAL;
|
|
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U && new_mtu > ETH_DATA_LEN)
|
|
return -EINVAL;
|
|
|
|
if (!netif_running(dev)) {
|
|
dev->mtu = new_mtu;
|
|
return 0;
|
|
}
|
|
|
|
imask = sky2_read32(hw, B0_IMSK);
|
|
sky2_write32(hw, B0_IMSK, 0);
|
|
|
|
dev->trans_start = jiffies; /* prevent tx timeout */
|
|
netif_stop_queue(dev);
|
|
netif_poll_disable(hw->dev[0]);
|
|
|
|
synchronize_irq(hw->pdev->irq);
|
|
|
|
ctl = gma_read16(hw, sky2->port, GM_GP_CTRL);
|
|
gma_write16(hw, sky2->port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA);
|
|
sky2_rx_stop(sky2);
|
|
sky2_rx_clean(sky2);
|
|
|
|
dev->mtu = new_mtu;
|
|
sky2->rx_bufsize = sky2_buf_size(new_mtu);
|
|
mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
|
|
GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
|
|
|
|
if (dev->mtu > ETH_DATA_LEN)
|
|
mode |= GM_SMOD_JUMBO_ENA;
|
|
|
|
gma_write16(hw, sky2->port, GM_SERIAL_MODE, mode);
|
|
|
|
sky2_write8(hw, RB_ADDR(rxqaddr[sky2->port], RB_CTRL), RB_ENA_OP_MD);
|
|
|
|
err = sky2_rx_start(sky2);
|
|
sky2_write32(hw, B0_IMSK, imask);
|
|
|
|
if (err)
|
|
dev_close(dev);
|
|
else {
|
|
gma_write16(hw, sky2->port, GM_GP_CTRL, ctl);
|
|
|
|
netif_poll_enable(hw->dev[0]);
|
|
netif_wake_queue(dev);
|
|
}
|
|
|
|
return err;
|
|
}
|
|
|
|
/*
|
|
* Receive one packet.
|
|
* For small packets or errors, just reuse existing skb.
|
|
* For larger packets, get new buffer.
|
|
*/
|
|
static struct sk_buff *sky2_receive(struct sky2_port *sky2,
|
|
u16 length, u32 status)
|
|
{
|
|
struct ring_info *re = sky2->rx_ring + sky2->rx_next;
|
|
struct sk_buff *skb = NULL;
|
|
|
|
if (unlikely(netif_msg_rx_status(sky2)))
|
|
printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
|
|
sky2->netdev->name, sky2->rx_next, status, length);
|
|
|
|
sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
|
|
prefetch(sky2->rx_ring + sky2->rx_next);
|
|
|
|
if (status & GMR_FS_ANY_ERR)
|
|
goto error;
|
|
|
|
if (!(status & GMR_FS_RX_OK))
|
|
goto resubmit;
|
|
|
|
if (length > sky2->netdev->mtu + ETH_HLEN)
|
|
goto oversize;
|
|
|
|
if (length < copybreak) {
|
|
skb = alloc_skb(length + 2, GFP_ATOMIC);
|
|
if (!skb)
|
|
goto resubmit;
|
|
|
|
skb_reserve(skb, 2);
|
|
pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->mapaddr,
|
|
length, PCI_DMA_FROMDEVICE);
|
|
memcpy(skb->data, re->skb->data, length);
|
|
skb->ip_summed = re->skb->ip_summed;
|
|
skb->csum = re->skb->csum;
|
|
pci_dma_sync_single_for_device(sky2->hw->pdev, re->mapaddr,
|
|
length, PCI_DMA_FROMDEVICE);
|
|
} else {
|
|
struct sk_buff *nskb;
|
|
|
|
nskb = sky2_alloc_skb(sky2->rx_bufsize, GFP_ATOMIC);
|
|
if (!nskb)
|
|
goto resubmit;
|
|
|
|
skb = re->skb;
|
|
re->skb = nskb;
|
|
pci_unmap_single(sky2->hw->pdev, re->mapaddr,
|
|
sky2->rx_bufsize, PCI_DMA_FROMDEVICE);
|
|
prefetch(skb->data);
|
|
|
|
re->mapaddr = pci_map_single(sky2->hw->pdev, nskb->data,
|
|
sky2->rx_bufsize, PCI_DMA_FROMDEVICE);
|
|
}
|
|
|
|
skb_put(skb, length);
|
|
resubmit:
|
|
re->skb->ip_summed = CHECKSUM_NONE;
|
|
sky2_rx_add(sky2, re->mapaddr);
|
|
|
|
/* Tell receiver about new buffers. */
|
|
sky2_put_idx(sky2->hw, rxqaddr[sky2->port], sky2->rx_put);
|
|
|
|
return skb;
|
|
|
|
oversize:
|
|
++sky2->net_stats.rx_over_errors;
|
|
goto resubmit;
|
|
|
|
error:
|
|
++sky2->net_stats.rx_errors;
|
|
|
|
if (netif_msg_rx_err(sky2) && net_ratelimit())
|
|
printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
|
|
sky2->netdev->name, status, length);
|
|
|
|
if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
|
|
sky2->net_stats.rx_length_errors++;
|
|
if (status & GMR_FS_FRAGMENT)
|
|
sky2->net_stats.rx_frame_errors++;
|
|
if (status & GMR_FS_CRC_ERR)
|
|
sky2->net_stats.rx_crc_errors++;
|
|
if (status & GMR_FS_RX_FF_OV)
|
|
sky2->net_stats.rx_fifo_errors++;
|
|
|
|
goto resubmit;
|
|
}
|
|
|
|
/* Transmit complete */
|
|
static inline void sky2_tx_done(struct net_device *dev, u16 last)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
if (netif_running(dev)) {
|
|
spin_lock(&sky2->tx_lock);
|
|
sky2_tx_complete(sky2, last);
|
|
spin_unlock(&sky2->tx_lock);
|
|
}
|
|
}
|
|
|
|
/* Process status response ring */
|
|
static int sky2_status_intr(struct sky2_hw *hw, int to_do)
|
|
{
|
|
int work_done = 0;
|
|
|
|
rmb();
|
|
|
|
for(;;) {
|
|
struct sky2_status_le *le = hw->st_le + hw->st_idx;
|
|
struct net_device *dev;
|
|
struct sky2_port *sky2;
|
|
struct sk_buff *skb;
|
|
u32 status;
|
|
u16 length;
|
|
u8 link, opcode;
|
|
|
|
opcode = le->opcode;
|
|
if (!opcode)
|
|
break;
|
|
opcode &= ~HW_OWNER;
|
|
|
|
hw->st_idx = (hw->st_idx + 1) % STATUS_RING_SIZE;
|
|
le->opcode = 0;
|
|
|
|
link = le->link;
|
|
BUG_ON(link >= 2);
|
|
dev = hw->dev[link];
|
|
|
|
sky2 = netdev_priv(dev);
|
|
length = le->length;
|
|
status = le->status;
|
|
|
|
switch (opcode) {
|
|
case OP_RXSTAT:
|
|
skb = sky2_receive(sky2, length, status);
|
|
if (!skb)
|
|
break;
|
|
|
|
skb->dev = dev;
|
|
skb->protocol = eth_type_trans(skb, dev);
|
|
dev->last_rx = jiffies;
|
|
|
|
#ifdef SKY2_VLAN_TAG_USED
|
|
if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
|
|
vlan_hwaccel_receive_skb(skb,
|
|
sky2->vlgrp,
|
|
be16_to_cpu(sky2->rx_tag));
|
|
} else
|
|
#endif
|
|
netif_receive_skb(skb);
|
|
|
|
if (++work_done >= to_do)
|
|
goto exit_loop;
|
|
break;
|
|
|
|
#ifdef SKY2_VLAN_TAG_USED
|
|
case OP_RXVLAN:
|
|
sky2->rx_tag = length;
|
|
break;
|
|
|
|
case OP_RXCHKSVLAN:
|
|
sky2->rx_tag = length;
|
|
/* fall through */
|
|
#endif
|
|
case OP_RXCHKS:
|
|
skb = sky2->rx_ring[sky2->rx_next].skb;
|
|
skb->ip_summed = CHECKSUM_HW;
|
|
skb->csum = le16_to_cpu(status);
|
|
break;
|
|
|
|
case OP_TXINDEXLE:
|
|
/* TX index reports status for both ports */
|
|
sky2_tx_done(hw->dev[0], status & 0xffff);
|
|
if (hw->dev[1])
|
|
sky2_tx_done(hw->dev[1],
|
|
((status >> 24) & 0xff)
|
|
| (u16)(length & 0xf) << 8);
|
|
break;
|
|
|
|
default:
|
|
if (net_ratelimit())
|
|
printk(KERN_WARNING PFX
|
|
"unknown status opcode 0x%x\n", opcode);
|
|
break;
|
|
}
|
|
}
|
|
|
|
exit_loop:
|
|
return work_done;
|
|
}
|
|
|
|
static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status)
|
|
{
|
|
struct net_device *dev = hw->dev[port];
|
|
|
|
if (net_ratelimit())
|
|
printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
|
|
dev->name, status);
|
|
|
|
if (status & Y2_IS_PAR_RD1) {
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: ram data read parity error\n",
|
|
dev->name);
|
|
/* Clear IRQ */
|
|
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR);
|
|
}
|
|
|
|
if (status & Y2_IS_PAR_WR1) {
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: ram data write parity error\n",
|
|
dev->name);
|
|
|
|
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR);
|
|
}
|
|
|
|
if (status & Y2_IS_PAR_MAC1) {
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
|
|
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE);
|
|
}
|
|
|
|
if (status & Y2_IS_PAR_RX1) {
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
|
|
sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR);
|
|
}
|
|
|
|
if (status & Y2_IS_TCP_TXA1) {
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: TCP segmentation error\n",
|
|
dev->name);
|
|
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP);
|
|
}
|
|
}
|
|
|
|
static void sky2_hw_intr(struct sky2_hw *hw)
|
|
{
|
|
u32 status = sky2_read32(hw, B0_HWE_ISRC);
|
|
|
|
if (status & Y2_IS_TIST_OV)
|
|
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
|
|
|
|
if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
|
|
u16 pci_err;
|
|
|
|
pci_err = sky2_pci_read16(hw, PCI_STATUS);
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
|
|
pci_name(hw->pdev), pci_err);
|
|
|
|
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
|
|
sky2_pci_write16(hw, PCI_STATUS,
|
|
pci_err | PCI_STATUS_ERROR_BITS);
|
|
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
|
|
}
|
|
|
|
if (status & Y2_IS_PCI_EXP) {
|
|
/* PCI-Express uncorrectable Error occurred */
|
|
u32 pex_err;
|
|
|
|
pex_err = sky2_pci_read32(hw, PEX_UNC_ERR_STAT);
|
|
|
|
if (net_ratelimit())
|
|
printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
|
|
pci_name(hw->pdev), pex_err);
|
|
|
|
/* clear the interrupt */
|
|
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
|
|
sky2_pci_write32(hw, PEX_UNC_ERR_STAT,
|
|
0xffffffffUL);
|
|
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
|
|
|
|
if (pex_err & PEX_FATAL_ERRORS) {
|
|
u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK);
|
|
hwmsk &= ~Y2_IS_PCI_EXP;
|
|
sky2_write32(hw, B0_HWE_IMSK, hwmsk);
|
|
}
|
|
}
|
|
|
|
if (status & Y2_HWE_L1_MASK)
|
|
sky2_hw_error(hw, 0, status);
|
|
status >>= 8;
|
|
if (status & Y2_HWE_L1_MASK)
|
|
sky2_hw_error(hw, 1, status);
|
|
}
|
|
|
|
static void sky2_mac_intr(struct sky2_hw *hw, unsigned port)
|
|
{
|
|
struct net_device *dev = hw->dev[port];
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
|
|
|
|
if (netif_msg_intr(sky2))
|
|
printk(KERN_INFO PFX "%s: mac interrupt status 0x%x\n",
|
|
dev->name, status);
|
|
|
|
if (status & GM_IS_RX_FF_OR) {
|
|
++sky2->net_stats.rx_fifo_errors;
|
|
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
|
|
}
|
|
|
|
if (status & GM_IS_TX_FF_UR) {
|
|
++sky2->net_stats.tx_fifo_errors;
|
|
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
|
|
}
|
|
}
|
|
|
|
/* This should never happen it is a fatal situation */
|
|
static void sky2_descriptor_error(struct sky2_hw *hw, unsigned port,
|
|
const char *rxtx, u32 mask)
|
|
{
|
|
struct net_device *dev = hw->dev[port];
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
u32 imask;
|
|
|
|
printk(KERN_ERR PFX "%s: %s descriptor error (hardware problem)\n",
|
|
dev ? dev->name : "<not registered>", rxtx);
|
|
|
|
imask = sky2_read32(hw, B0_IMSK);
|
|
imask &= ~mask;
|
|
sky2_write32(hw, B0_IMSK, imask);
|
|
|
|
if (dev) {
|
|
spin_lock(&sky2->phy_lock);
|
|
sky2_link_down(sky2);
|
|
spin_unlock(&sky2->phy_lock);
|
|
}
|
|
}
|
|
|
|
static int sky2_poll(struct net_device *dev0, int *budget)
|
|
{
|
|
struct sky2_hw *hw = ((struct sky2_port *) netdev_priv(dev0))->hw;
|
|
int work_limit = min(dev0->quota, *budget);
|
|
int work_done = 0;
|
|
u32 status = sky2_read32(hw, B0_Y2_SP_EISR);
|
|
|
|
if (unlikely(status & ~Y2_IS_STAT_BMU)) {
|
|
if (status & Y2_IS_HW_ERR)
|
|
sky2_hw_intr(hw);
|
|
|
|
if (status & Y2_IS_IRQ_PHY1)
|
|
sky2_phy_intr(hw, 0);
|
|
|
|
if (status & Y2_IS_IRQ_PHY2)
|
|
sky2_phy_intr(hw, 1);
|
|
|
|
if (status & Y2_IS_IRQ_MAC1)
|
|
sky2_mac_intr(hw, 0);
|
|
|
|
if (status & Y2_IS_IRQ_MAC2)
|
|
sky2_mac_intr(hw, 1);
|
|
|
|
if (status & Y2_IS_CHK_RX1)
|
|
sky2_descriptor_error(hw, 0, "receive", Y2_IS_CHK_RX1);
|
|
|
|
if (status & Y2_IS_CHK_RX2)
|
|
sky2_descriptor_error(hw, 1, "receive", Y2_IS_CHK_RX2);
|
|
|
|
if (status & Y2_IS_CHK_TXA1)
|
|
sky2_descriptor_error(hw, 0, "transmit", Y2_IS_CHK_TXA1);
|
|
|
|
if (status & Y2_IS_CHK_TXA2)
|
|
sky2_descriptor_error(hw, 1, "transmit", Y2_IS_CHK_TXA2);
|
|
}
|
|
|
|
if (status & Y2_IS_STAT_BMU) {
|
|
work_done = sky2_status_intr(hw, work_limit);
|
|
*budget -= work_done;
|
|
dev0->quota -= work_done;
|
|
|
|
if (work_done >= work_limit)
|
|
return 1;
|
|
|
|
sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
|
|
}
|
|
|
|
netif_rx_complete(dev0);
|
|
|
|
status = sky2_read32(hw, B0_Y2_SP_LISR);
|
|
return 0;
|
|
}
|
|
|
|
static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
|
|
{
|
|
struct sky2_hw *hw = dev_id;
|
|
struct net_device *dev0 = hw->dev[0];
|
|
u32 status;
|
|
|
|
/* Reading this mask interrupts as side effect */
|
|
status = sky2_read32(hw, B0_Y2_SP_ISRC2);
|
|
if (status == 0 || status == ~0)
|
|
return IRQ_NONE;
|
|
|
|
prefetch(&hw->st_le[hw->st_idx]);
|
|
if (likely(__netif_rx_schedule_prep(dev0)))
|
|
__netif_rx_schedule(dev0);
|
|
else
|
|
printk(KERN_DEBUG PFX "irq race detected\n");
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
static void sky2_netpoll(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
sky2_intr(sky2->hw->pdev->irq, sky2->hw, NULL);
|
|
}
|
|
#endif
|
|
|
|
/* Chip internal frequency for clock calculations */
|
|
static inline u32 sky2_mhz(const struct sky2_hw *hw)
|
|
{
|
|
switch (hw->chip_id) {
|
|
case CHIP_ID_YUKON_EC:
|
|
case CHIP_ID_YUKON_EC_U:
|
|
return 125; /* 125 Mhz */
|
|
case CHIP_ID_YUKON_FE:
|
|
return 100; /* 100 Mhz */
|
|
default: /* YUKON_XL */
|
|
return 156; /* 156 Mhz */
|
|
}
|
|
}
|
|
|
|
static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us)
|
|
{
|
|
return sky2_mhz(hw) * us;
|
|
}
|
|
|
|
static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk)
|
|
{
|
|
return clk / sky2_mhz(hw);
|
|
}
|
|
|
|
|
|
static int sky2_reset(struct sky2_hw *hw)
|
|
{
|
|
u16 status;
|
|
u8 t8, pmd_type;
|
|
int i;
|
|
|
|
sky2_write8(hw, B0_CTST, CS_RST_CLR);
|
|
|
|
hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
|
|
if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
|
|
printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
|
|
pci_name(hw->pdev), hw->chip_id);
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
|
|
|
|
/* This rev is really old, and requires untested workarounds */
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == CHIP_REV_YU_EC_A1) {
|
|
printk(KERN_ERR PFX "%s: unsupported revision Yukon-%s (0x%x) rev %d\n",
|
|
pci_name(hw->pdev), yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
|
|
hw->chip_id, hw->chip_rev);
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
/* This chip is new and not tested yet */
|
|
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
|
|
pr_info(PFX "%s: is a version of Yukon 2 chipset that has not been tested yet.\n",
|
|
pci_name(hw->pdev));
|
|
pr_info("Please report success/failure to maintainer <shemminger@osdl.org>\n");
|
|
}
|
|
|
|
/* disable ASF */
|
|
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
|
|
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
|
|
sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
|
|
}
|
|
|
|
/* do a SW reset */
|
|
sky2_write8(hw, B0_CTST, CS_RST_SET);
|
|
sky2_write8(hw, B0_CTST, CS_RST_CLR);
|
|
|
|
/* clear PCI errors, if any */
|
|
status = sky2_pci_read16(hw, PCI_STATUS);
|
|
|
|
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
|
|
sky2_pci_write16(hw, PCI_STATUS, status | PCI_STATUS_ERROR_BITS);
|
|
|
|
|
|
sky2_write8(hw, B0_CTST, CS_MRST_CLR);
|
|
|
|
/* clear any PEX errors */
|
|
if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP))
|
|
sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
|
|
|
|
|
|
pmd_type = sky2_read8(hw, B2_PMD_TYP);
|
|
hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
|
|
|
|
hw->ports = 1;
|
|
t8 = sky2_read8(hw, B2_Y2_HW_RES);
|
|
if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
|
|
if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC))
|
|
++hw->ports;
|
|
}
|
|
|
|
sky2_set_power_state(hw, PCI_D0);
|
|
|
|
for (i = 0; i < hw->ports; i++) {
|
|
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
|
|
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
|
|
}
|
|
|
|
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
|
|
|
|
/* Clear I2C IRQ noise */
|
|
sky2_write32(hw, B2_I2C_IRQ, 1);
|
|
|
|
/* turn off hardware timer (unused) */
|
|
sky2_write8(hw, B2_TI_CTRL, TIM_STOP);
|
|
sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
|
|
|
|
sky2_write8(hw, B0_Y2LED, LED_STAT_ON);
|
|
|
|
/* Turn off descriptor polling */
|
|
sky2_write32(hw, B28_DPT_CTRL, DPT_STOP);
|
|
|
|
/* Turn off receive timestamp */
|
|
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP);
|
|
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
|
|
|
|
/* enable the Tx Arbiters */
|
|
for (i = 0; i < hw->ports; i++)
|
|
sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB);
|
|
|
|
/* Initialize ram interface */
|
|
for (i = 0; i < hw->ports; i++) {
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR);
|
|
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53);
|
|
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53);
|
|
}
|
|
|
|
sky2_write32(hw, B0_HWE_IMSK, Y2_HWE_ALL_MASK);
|
|
|
|
for (i = 0; i < hw->ports; i++)
|
|
sky2_phy_reset(hw, i);
|
|
|
|
memset(hw->st_le, 0, STATUS_LE_BYTES);
|
|
hw->st_idx = 0;
|
|
|
|
sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET);
|
|
sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR);
|
|
|
|
sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma);
|
|
sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32);
|
|
|
|
/* Set the list last index */
|
|
sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1);
|
|
|
|
sky2_write16(hw, STAT_TX_IDX_TH, 10);
|
|
sky2_write8(hw, STAT_FIFO_WM, 16);
|
|
|
|
/* set Status-FIFO ISR watermark */
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0)
|
|
sky2_write8(hw, STAT_FIFO_ISR_WM, 4);
|
|
else
|
|
sky2_write8(hw, STAT_FIFO_ISR_WM, 16);
|
|
|
|
sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000));
|
|
sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20));
|
|
sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100));
|
|
|
|
/* enable status unit */
|
|
sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON);
|
|
|
|
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
|
|
sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
|
|
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static u32 sky2_supported_modes(const struct sky2_hw *hw)
|
|
{
|
|
u32 modes;
|
|
if (hw->copper) {
|
|
modes = SUPPORTED_10baseT_Half
|
|
| SUPPORTED_10baseT_Full
|
|
| SUPPORTED_100baseT_Half
|
|
| SUPPORTED_100baseT_Full
|
|
| SUPPORTED_Autoneg | SUPPORTED_TP;
|
|
|
|
if (hw->chip_id != CHIP_ID_YUKON_FE)
|
|
modes |= SUPPORTED_1000baseT_Half
|
|
| SUPPORTED_1000baseT_Full;
|
|
} else
|
|
modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
|
|
| SUPPORTED_Autoneg;
|
|
return modes;
|
|
}
|
|
|
|
static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
|
|
ecmd->transceiver = XCVR_INTERNAL;
|
|
ecmd->supported = sky2_supported_modes(hw);
|
|
ecmd->phy_address = PHY_ADDR_MARV;
|
|
if (hw->copper) {
|
|
ecmd->supported = SUPPORTED_10baseT_Half
|
|
| SUPPORTED_10baseT_Full
|
|
| SUPPORTED_100baseT_Half
|
|
| SUPPORTED_100baseT_Full
|
|
| SUPPORTED_1000baseT_Half
|
|
| SUPPORTED_1000baseT_Full
|
|
| SUPPORTED_Autoneg | SUPPORTED_TP;
|
|
ecmd->port = PORT_TP;
|
|
} else
|
|
ecmd->port = PORT_FIBRE;
|
|
|
|
ecmd->advertising = sky2->advertising;
|
|
ecmd->autoneg = sky2->autoneg;
|
|
ecmd->speed = sky2->speed;
|
|
ecmd->duplex = sky2->duplex;
|
|
return 0;
|
|
}
|
|
|
|
static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
const struct sky2_hw *hw = sky2->hw;
|
|
u32 supported = sky2_supported_modes(hw);
|
|
|
|
if (ecmd->autoneg == AUTONEG_ENABLE) {
|
|
ecmd->advertising = supported;
|
|
sky2->duplex = -1;
|
|
sky2->speed = -1;
|
|
} else {
|
|
u32 setting;
|
|
|
|
switch (ecmd->speed) {
|
|
case SPEED_1000:
|
|
if (ecmd->duplex == DUPLEX_FULL)
|
|
setting = SUPPORTED_1000baseT_Full;
|
|
else if (ecmd->duplex == DUPLEX_HALF)
|
|
setting = SUPPORTED_1000baseT_Half;
|
|
else
|
|
return -EINVAL;
|
|
break;
|
|
case SPEED_100:
|
|
if (ecmd->duplex == DUPLEX_FULL)
|
|
setting = SUPPORTED_100baseT_Full;
|
|
else if (ecmd->duplex == DUPLEX_HALF)
|
|
setting = SUPPORTED_100baseT_Half;
|
|
else
|
|
return -EINVAL;
|
|
break;
|
|
|
|
case SPEED_10:
|
|
if (ecmd->duplex == DUPLEX_FULL)
|
|
setting = SUPPORTED_10baseT_Full;
|
|
else if (ecmd->duplex == DUPLEX_HALF)
|
|
setting = SUPPORTED_10baseT_Half;
|
|
else
|
|
return -EINVAL;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
if ((setting & supported) == 0)
|
|
return -EINVAL;
|
|
|
|
sky2->speed = ecmd->speed;
|
|
sky2->duplex = ecmd->duplex;
|
|
}
|
|
|
|
sky2->autoneg = ecmd->autoneg;
|
|
sky2->advertising = ecmd->advertising;
|
|
|
|
if (netif_running(dev))
|
|
sky2_phy_reinit(sky2);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sky2_get_drvinfo(struct net_device *dev,
|
|
struct ethtool_drvinfo *info)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
strcpy(info->driver, DRV_NAME);
|
|
strcpy(info->version, DRV_VERSION);
|
|
strcpy(info->fw_version, "N/A");
|
|
strcpy(info->bus_info, pci_name(sky2->hw->pdev));
|
|
}
|
|
|
|
static const struct sky2_stat {
|
|
char name[ETH_GSTRING_LEN];
|
|
u16 offset;
|
|
} sky2_stats[] = {
|
|
{ "tx_bytes", GM_TXO_OK_HI },
|
|
{ "rx_bytes", GM_RXO_OK_HI },
|
|
{ "tx_broadcast", GM_TXF_BC_OK },
|
|
{ "rx_broadcast", GM_RXF_BC_OK },
|
|
{ "tx_multicast", GM_TXF_MC_OK },
|
|
{ "rx_multicast", GM_RXF_MC_OK },
|
|
{ "tx_unicast", GM_TXF_UC_OK },
|
|
{ "rx_unicast", GM_RXF_UC_OK },
|
|
{ "tx_mac_pause", GM_TXF_MPAUSE },
|
|
{ "rx_mac_pause", GM_RXF_MPAUSE },
|
|
{ "collisions", GM_TXF_COL },
|
|
{ "late_collision",GM_TXF_LAT_COL },
|
|
{ "aborted", GM_TXF_ABO_COL },
|
|
{ "single_collisions", GM_TXF_SNG_COL },
|
|
{ "multi_collisions", GM_TXF_MUL_COL },
|
|
|
|
{ "rx_short", GM_RXF_SHT },
|
|
{ "rx_runt", GM_RXE_FRAG },
|
|
{ "rx_64_byte_packets", GM_RXF_64B },
|
|
{ "rx_65_to_127_byte_packets", GM_RXF_127B },
|
|
{ "rx_128_to_255_byte_packets", GM_RXF_255B },
|
|
{ "rx_256_to_511_byte_packets", GM_RXF_511B },
|
|
{ "rx_512_to_1023_byte_packets", GM_RXF_1023B },
|
|
{ "rx_1024_to_1518_byte_packets", GM_RXF_1518B },
|
|
{ "rx_1518_to_max_byte_packets", GM_RXF_MAX_SZ },
|
|
{ "rx_too_long", GM_RXF_LNG_ERR },
|
|
{ "rx_fifo_overflow", GM_RXE_FIFO_OV },
|
|
{ "rx_jabber", GM_RXF_JAB_PKT },
|
|
{ "rx_fcs_error", GM_RXF_FCS_ERR },
|
|
|
|
{ "tx_64_byte_packets", GM_TXF_64B },
|
|
{ "tx_65_to_127_byte_packets", GM_TXF_127B },
|
|
{ "tx_128_to_255_byte_packets", GM_TXF_255B },
|
|
{ "tx_256_to_511_byte_packets", GM_TXF_511B },
|
|
{ "tx_512_to_1023_byte_packets", GM_TXF_1023B },
|
|
{ "tx_1024_to_1518_byte_packets", GM_TXF_1518B },
|
|
{ "tx_1519_to_max_byte_packets", GM_TXF_MAX_SZ },
|
|
{ "tx_fifo_underrun", GM_TXE_FIFO_UR },
|
|
};
|
|
|
|
static u32 sky2_get_rx_csum(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
return sky2->rx_csum;
|
|
}
|
|
|
|
static int sky2_set_rx_csum(struct net_device *dev, u32 data)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
sky2->rx_csum = data;
|
|
|
|
sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
|
|
data ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static u32 sky2_get_msglevel(struct net_device *netdev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(netdev);
|
|
return sky2->msg_enable;
|
|
}
|
|
|
|
static int sky2_nway_reset(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
if (sky2->autoneg != AUTONEG_ENABLE)
|
|
return -EINVAL;
|
|
|
|
sky2_phy_reinit(sky2);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count)
|
|
{
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
int i;
|
|
|
|
data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32
|
|
| (u64) gma_read32(hw, port, GM_TXO_OK_LO);
|
|
data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32
|
|
| (u64) gma_read32(hw, port, GM_RXO_OK_LO);
|
|
|
|
for (i = 2; i < count; i++)
|
|
data[i] = (u64) gma_read32(hw, port, sky2_stats[i].offset);
|
|
}
|
|
|
|
static void sky2_set_msglevel(struct net_device *netdev, u32 value)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(netdev);
|
|
sky2->msg_enable = value;
|
|
}
|
|
|
|
static int sky2_get_stats_count(struct net_device *dev)
|
|
{
|
|
return ARRAY_SIZE(sky2_stats);
|
|
}
|
|
|
|
static void sky2_get_ethtool_stats(struct net_device *dev,
|
|
struct ethtool_stats *stats, u64 * data)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats));
|
|
}
|
|
|
|
static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data)
|
|
{
|
|
int i;
|
|
|
|
switch (stringset) {
|
|
case ETH_SS_STATS:
|
|
for (i = 0; i < ARRAY_SIZE(sky2_stats); i++)
|
|
memcpy(data + i * ETH_GSTRING_LEN,
|
|
sky2_stats[i].name, ETH_GSTRING_LEN);
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* Use hardware MIB variables for critical path statistics and
|
|
* transmit feedback not reported at interrupt.
|
|
* Other errors are accounted for in interrupt handler.
|
|
*/
|
|
static struct net_device_stats *sky2_get_stats(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
u64 data[13];
|
|
|
|
sky2_phy_stats(sky2, data, ARRAY_SIZE(data));
|
|
|
|
sky2->net_stats.tx_bytes = data[0];
|
|
sky2->net_stats.rx_bytes = data[1];
|
|
sky2->net_stats.tx_packets = data[2] + data[4] + data[6];
|
|
sky2->net_stats.rx_packets = data[3] + data[5] + data[7];
|
|
sky2->net_stats.multicast = data[3] + data[5];
|
|
sky2->net_stats.collisions = data[10];
|
|
sky2->net_stats.tx_aborted_errors = data[12];
|
|
|
|
return &sky2->net_stats;
|
|
}
|
|
|
|
static int sky2_set_mac_address(struct net_device *dev, void *p)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
const struct sockaddr *addr = p;
|
|
|
|
if (!is_valid_ether_addr(addr->sa_data))
|
|
return -EADDRNOTAVAIL;
|
|
|
|
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
|
|
memcpy_toio(hw->regs + B2_MAC_1 + port * 8,
|
|
dev->dev_addr, ETH_ALEN);
|
|
memcpy_toio(hw->regs + B2_MAC_2 + port * 8,
|
|
dev->dev_addr, ETH_ALEN);
|
|
|
|
/* virtual address for data */
|
|
gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
|
|
|
|
/* physical address: used for pause frames */
|
|
gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sky2_set_multicast(struct net_device *dev)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
struct dev_mc_list *list = dev->mc_list;
|
|
u16 reg;
|
|
u8 filter[8];
|
|
|
|
memset(filter, 0, sizeof(filter));
|
|
|
|
reg = gma_read16(hw, port, GM_RX_CTRL);
|
|
reg |= GM_RXCR_UCF_ENA;
|
|
|
|
if (dev->flags & IFF_PROMISC) /* promiscuous */
|
|
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
|
|
else if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 16) /* all multicast */
|
|
memset(filter, 0xff, sizeof(filter));
|
|
else if (dev->mc_count == 0) /* no multicast */
|
|
reg &= ~GM_RXCR_MCF_ENA;
|
|
else {
|
|
int i;
|
|
reg |= GM_RXCR_MCF_ENA;
|
|
|
|
for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
|
|
u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
|
|
filter[bit / 8] |= 1 << (bit % 8);
|
|
}
|
|
}
|
|
|
|
gma_write16(hw, port, GM_MC_ADDR_H1,
|
|
(u16) filter[0] | ((u16) filter[1] << 8));
|
|
gma_write16(hw, port, GM_MC_ADDR_H2,
|
|
(u16) filter[2] | ((u16) filter[3] << 8));
|
|
gma_write16(hw, port, GM_MC_ADDR_H3,
|
|
(u16) filter[4] | ((u16) filter[5] << 8));
|
|
gma_write16(hw, port, GM_MC_ADDR_H4,
|
|
(u16) filter[6] | ((u16) filter[7] << 8));
|
|
|
|
gma_write16(hw, port, GM_RX_CTRL, reg);
|
|
}
|
|
|
|
/* Can have one global because blinking is controlled by
|
|
* ethtool and that is always under RTNL mutex
|
|
*/
|
|
static void sky2_led(struct sky2_hw *hw, unsigned port, int on)
|
|
{
|
|
u16 pg;
|
|
|
|
switch (hw->chip_id) {
|
|
case CHIP_ID_YUKON_XL:
|
|
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
|
|
on ? (PHY_M_LEDC_LOS_CTRL(1) |
|
|
PHY_M_LEDC_INIT_CTRL(7) |
|
|
PHY_M_LEDC_STA1_CTRL(7) |
|
|
PHY_M_LEDC_STA0_CTRL(7))
|
|
: 0);
|
|
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
|
|
break;
|
|
|
|
default:
|
|
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
|
|
gm_phy_write(hw, port, PHY_MARV_LED_OVER,
|
|
on ? PHY_M_LED_MO_DUP(MO_LED_ON) |
|
|
PHY_M_LED_MO_10(MO_LED_ON) |
|
|
PHY_M_LED_MO_100(MO_LED_ON) |
|
|
PHY_M_LED_MO_1000(MO_LED_ON) |
|
|
PHY_M_LED_MO_RX(MO_LED_ON)
|
|
: PHY_M_LED_MO_DUP(MO_LED_OFF) |
|
|
PHY_M_LED_MO_10(MO_LED_OFF) |
|
|
PHY_M_LED_MO_100(MO_LED_OFF) |
|
|
PHY_M_LED_MO_1000(MO_LED_OFF) |
|
|
PHY_M_LED_MO_RX(MO_LED_OFF));
|
|
|
|
}
|
|
}
|
|
|
|
/* blink LED's for finding board */
|
|
static int sky2_phys_id(struct net_device *dev, u32 data)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
unsigned port = sky2->port;
|
|
u16 ledctrl, ledover = 0;
|
|
long ms;
|
|
int interrupted;
|
|
int onoff = 1;
|
|
|
|
if (!data || data > (u32) (MAX_SCHEDULE_TIMEOUT / HZ))
|
|
ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT);
|
|
else
|
|
ms = data * 1000;
|
|
|
|
/* save initial values */
|
|
spin_lock_bh(&sky2->phy_lock);
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL) {
|
|
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
|
|
ledctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
|
|
} else {
|
|
ledctrl = gm_phy_read(hw, port, PHY_MARV_LED_CTRL);
|
|
ledover = gm_phy_read(hw, port, PHY_MARV_LED_OVER);
|
|
}
|
|
|
|
interrupted = 0;
|
|
while (!interrupted && ms > 0) {
|
|
sky2_led(hw, port, onoff);
|
|
onoff = !onoff;
|
|
|
|
spin_unlock_bh(&sky2->phy_lock);
|
|
interrupted = msleep_interruptible(250);
|
|
spin_lock_bh(&sky2->phy_lock);
|
|
|
|
ms -= 250;
|
|
}
|
|
|
|
/* resume regularly scheduled programming */
|
|
if (hw->chip_id == CHIP_ID_YUKON_XL) {
|
|
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
|
|
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ledctrl);
|
|
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
|
|
} else {
|
|
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
|
|
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
|
|
}
|
|
spin_unlock_bh(&sky2->phy_lock);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sky2_get_pauseparam(struct net_device *dev,
|
|
struct ethtool_pauseparam *ecmd)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
ecmd->tx_pause = sky2->tx_pause;
|
|
ecmd->rx_pause = sky2->rx_pause;
|
|
ecmd->autoneg = sky2->autoneg;
|
|
}
|
|
|
|
static int sky2_set_pauseparam(struct net_device *dev,
|
|
struct ethtool_pauseparam *ecmd)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
int err = 0;
|
|
|
|
sky2->autoneg = ecmd->autoneg;
|
|
sky2->tx_pause = ecmd->tx_pause != 0;
|
|
sky2->rx_pause = ecmd->rx_pause != 0;
|
|
|
|
sky2_phy_reinit(sky2);
|
|
|
|
return err;
|
|
}
|
|
|
|
static int sky2_get_coalesce(struct net_device *dev,
|
|
struct ethtool_coalesce *ecmd)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
|
|
if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_STOP)
|
|
ecmd->tx_coalesce_usecs = 0;
|
|
else {
|
|
u32 clks = sky2_read32(hw, STAT_TX_TIMER_INI);
|
|
ecmd->tx_coalesce_usecs = sky2_clk2us(hw, clks);
|
|
}
|
|
ecmd->tx_max_coalesced_frames = sky2_read16(hw, STAT_TX_IDX_TH);
|
|
|
|
if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_STOP)
|
|
ecmd->rx_coalesce_usecs = 0;
|
|
else {
|
|
u32 clks = sky2_read32(hw, STAT_LEV_TIMER_INI);
|
|
ecmd->rx_coalesce_usecs = sky2_clk2us(hw, clks);
|
|
}
|
|
ecmd->rx_max_coalesced_frames = sky2_read8(hw, STAT_FIFO_WM);
|
|
|
|
if (sky2_read8(hw, STAT_ISR_TIMER_CTRL) == TIM_STOP)
|
|
ecmd->rx_coalesce_usecs_irq = 0;
|
|
else {
|
|
u32 clks = sky2_read32(hw, STAT_ISR_TIMER_INI);
|
|
ecmd->rx_coalesce_usecs_irq = sky2_clk2us(hw, clks);
|
|
}
|
|
|
|
ecmd->rx_max_coalesced_frames_irq = sky2_read8(hw, STAT_FIFO_ISR_WM);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Note: this affect both ports */
|
|
static int sky2_set_coalesce(struct net_device *dev,
|
|
struct ethtool_coalesce *ecmd)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
struct sky2_hw *hw = sky2->hw;
|
|
const u32 tmax = sky2_clk2us(hw, 0x0ffffff);
|
|
|
|
if (ecmd->tx_coalesce_usecs > tmax ||
|
|
ecmd->rx_coalesce_usecs > tmax ||
|
|
ecmd->rx_coalesce_usecs_irq > tmax)
|
|
return -EINVAL;
|
|
|
|
if (ecmd->tx_max_coalesced_frames >= TX_RING_SIZE-1)
|
|
return -EINVAL;
|
|
if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING)
|
|
return -EINVAL;
|
|
if (ecmd->rx_max_coalesced_frames_irq >RX_MAX_PENDING)
|
|
return -EINVAL;
|
|
|
|
if (ecmd->tx_coalesce_usecs == 0)
|
|
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
|
|
else {
|
|
sky2_write32(hw, STAT_TX_TIMER_INI,
|
|
sky2_us2clk(hw, ecmd->tx_coalesce_usecs));
|
|
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
|
|
}
|
|
sky2_write16(hw, STAT_TX_IDX_TH, ecmd->tx_max_coalesced_frames);
|
|
|
|
if (ecmd->rx_coalesce_usecs == 0)
|
|
sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP);
|
|
else {
|
|
sky2_write32(hw, STAT_LEV_TIMER_INI,
|
|
sky2_us2clk(hw, ecmd->rx_coalesce_usecs));
|
|
sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
|
|
}
|
|
sky2_write8(hw, STAT_FIFO_WM, ecmd->rx_max_coalesced_frames);
|
|
|
|
if (ecmd->rx_coalesce_usecs_irq == 0)
|
|
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP);
|
|
else {
|
|
sky2_write32(hw, STAT_ISR_TIMER_INI,
|
|
sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq));
|
|
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
|
|
}
|
|
sky2_write8(hw, STAT_FIFO_ISR_WM, ecmd->rx_max_coalesced_frames_irq);
|
|
return 0;
|
|
}
|
|
|
|
static void sky2_get_ringparam(struct net_device *dev,
|
|
struct ethtool_ringparam *ering)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
ering->rx_max_pending = RX_MAX_PENDING;
|
|
ering->rx_mini_max_pending = 0;
|
|
ering->rx_jumbo_max_pending = 0;
|
|
ering->tx_max_pending = TX_RING_SIZE - 1;
|
|
|
|
ering->rx_pending = sky2->rx_pending;
|
|
ering->rx_mini_pending = 0;
|
|
ering->rx_jumbo_pending = 0;
|
|
ering->tx_pending = sky2->tx_pending;
|
|
}
|
|
|
|
static int sky2_set_ringparam(struct net_device *dev,
|
|
struct ethtool_ringparam *ering)
|
|
{
|
|
struct sky2_port *sky2 = netdev_priv(dev);
|
|
int err = 0;
|
|
|
|
if (ering->rx_pending > RX_MAX_PENDING ||
|
|
ering->rx_pending < 8 ||
|
|
ering->tx_pending < MAX_SKB_TX_LE ||
|
|
ering->tx_pending > TX_RING_SIZE - 1)
|
|
return -EINVAL;
|
|
|
|
if (netif_running(dev))
|
|
sky2_down(dev);
|
|
|
|
sky2->rx_pending = ering->rx_pending;
|
|
sky2->tx_pending = ering->tx_pending;
|
|
|
|
if (netif_running(dev)) {
|
|
err = sky2_up(dev);
|
|
if (err)
|
|
dev_close(dev);
|
|
else
|
|
sky2_set_multicast(dev);
|
|
}
|
|
|
|
return err;
|
|
}
|
|
|
|
static int sky2_get_regs_len(struct net_device *dev)
|
|
{
|
|
return 0x4000;
|
|
}
|
|
|
|
/*
|
|
* Returns copy of control register region
|
|
* Note: access to the RAM address register set will cause timeouts.
|
|
*/
|
|
static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs,
|
|
void *p)
|
|
{
|
|
const struct sky2_port *sky2 = netdev_priv(dev);
|
|
const void __iomem *io = sky2->hw->regs;
|
|
|
|
BUG_ON(regs->len < B3_RI_WTO_R1);
|
|
regs->version = 1;
|
|
memset(p, 0, regs->len);
|
|
|
|
memcpy_fromio(p, io, B3_RAM_ADDR);
|
|
|
|
memcpy_fromio(p + B3_RI_WTO_R1,
|
|
io + B3_RI_WTO_R1,
|
|
regs->len - B3_RI_WTO_R1);
|
|
}
|
|
|
|
static struct ethtool_ops sky2_ethtool_ops = {
|
|
.get_settings = sky2_get_settings,
|
|
.set_settings = sky2_set_settings,
|
|
.get_drvinfo = sky2_get_drvinfo,
|
|
.get_msglevel = sky2_get_msglevel,
|
|
.set_msglevel = sky2_set_msglevel,
|
|
.nway_reset = sky2_nway_reset,
|
|
.get_regs_len = sky2_get_regs_len,
|
|
.get_regs = sky2_get_regs,
|
|
.get_link = ethtool_op_get_link,
|
|
.get_sg = ethtool_op_get_sg,
|
|
.set_sg = ethtool_op_set_sg,
|
|
.get_tx_csum = ethtool_op_get_tx_csum,
|
|
.set_tx_csum = ethtool_op_set_tx_csum,
|
|
.get_tso = ethtool_op_get_tso,
|
|
.set_tso = ethtool_op_set_tso,
|
|
.get_rx_csum = sky2_get_rx_csum,
|
|
.set_rx_csum = sky2_set_rx_csum,
|
|
.get_strings = sky2_get_strings,
|
|
.get_coalesce = sky2_get_coalesce,
|
|
.set_coalesce = sky2_set_coalesce,
|
|
.get_ringparam = sky2_get_ringparam,
|
|
.set_ringparam = sky2_set_ringparam,
|
|
.get_pauseparam = sky2_get_pauseparam,
|
|
.set_pauseparam = sky2_set_pauseparam,
|
|
.phys_id = sky2_phys_id,
|
|
.get_stats_count = sky2_get_stats_count,
|
|
.get_ethtool_stats = sky2_get_ethtool_stats,
|
|
.get_perm_addr = ethtool_op_get_perm_addr,
|
|
};
|
|
|
|
/* Initialize network device */
|
|
static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
|
|
unsigned port, int highmem)
|
|
{
|
|
struct sky2_port *sky2;
|
|
struct net_device *dev = alloc_etherdev(sizeof(*sky2));
|
|
|
|
if (!dev) {
|
|
printk(KERN_ERR "sky2 etherdev alloc failed");
|
|
return NULL;
|
|
}
|
|
|
|
SET_MODULE_OWNER(dev);
|
|
SET_NETDEV_DEV(dev, &hw->pdev->dev);
|
|
dev->irq = hw->pdev->irq;
|
|
dev->open = sky2_up;
|
|
dev->stop = sky2_down;
|
|
dev->do_ioctl = sky2_ioctl;
|
|
dev->hard_start_xmit = sky2_xmit_frame;
|
|
dev->get_stats = sky2_get_stats;
|
|
dev->set_multicast_list = sky2_set_multicast;
|
|
dev->set_mac_address = sky2_set_mac_address;
|
|
dev->change_mtu = sky2_change_mtu;
|
|
SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
|
|
dev->tx_timeout = sky2_tx_timeout;
|
|
dev->watchdog_timeo = TX_WATCHDOG;
|
|
if (port == 0)
|
|
dev->poll = sky2_poll;
|
|
dev->weight = NAPI_WEIGHT;
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
dev->poll_controller = sky2_netpoll;
|
|
#endif
|
|
|
|
sky2 = netdev_priv(dev);
|
|
sky2->netdev = dev;
|
|
sky2->hw = hw;
|
|
sky2->msg_enable = netif_msg_init(debug, default_msg);
|
|
|
|
spin_lock_init(&sky2->tx_lock);
|
|
/* Auto speed and flow control */
|
|
sky2->autoneg = AUTONEG_ENABLE;
|
|
sky2->tx_pause = 1;
|
|
sky2->rx_pause = 1;
|
|
sky2->duplex = -1;
|
|
sky2->speed = -1;
|
|
sky2->advertising = sky2_supported_modes(hw);
|
|
|
|
/* Receive checksum disabled for Yukon XL
|
|
* because of observed problems with incorrect
|
|
* values when multiple packets are received in one interrupt
|
|
*/
|
|
sky2->rx_csum = (hw->chip_id != CHIP_ID_YUKON_XL);
|
|
|
|
spin_lock_init(&sky2->phy_lock);
|
|
sky2->tx_pending = TX_DEF_PENDING;
|
|
sky2->rx_pending = RX_DEF_PENDING;
|
|
sky2->rx_bufsize = sky2_buf_size(ETH_DATA_LEN);
|
|
|
|
hw->dev[port] = dev;
|
|
|
|
sky2->port = port;
|
|
|
|
dev->features |= NETIF_F_LLTX;
|
|
if (hw->chip_id != CHIP_ID_YUKON_EC_U)
|
|
dev->features |= NETIF_F_TSO;
|
|
if (highmem)
|
|
dev->features |= NETIF_F_HIGHDMA;
|
|
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
|
|
|
|
#ifdef SKY2_VLAN_TAG_USED
|
|
dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
|
|
dev->vlan_rx_register = sky2_vlan_rx_register;
|
|
dev->vlan_rx_kill_vid = sky2_vlan_rx_kill_vid;
|
|
#endif
|
|
|
|
/* read the mac address */
|
|
memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN);
|
|
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
|
|
|
|
/* device is off until link detection */
|
|
netif_carrier_off(dev);
|
|
netif_stop_queue(dev);
|
|
|
|
return dev;
|
|
}
|
|
|
|
static void __devinit sky2_show_addr(struct net_device *dev)
|
|
{
|
|
const struct sky2_port *sky2 = netdev_priv(dev);
|
|
|
|
if (netif_msg_probe(sky2))
|
|
printk(KERN_INFO PFX "%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
|
|
dev->name,
|
|
dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
|
|
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
|
|
}
|
|
|
|
/* Handle software interrupt used during MSI test */
|
|
static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id,
|
|
struct pt_regs *regs)
|
|
{
|
|
struct sky2_hw *hw = dev_id;
|
|
u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2);
|
|
|
|
if (status == 0)
|
|
return IRQ_NONE;
|
|
|
|
if (status & Y2_IS_IRQ_SW) {
|
|
hw->msi_detected = 1;
|
|
wake_up(&hw->msi_wait);
|
|
sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
|
|
}
|
|
sky2_write32(hw, B0_Y2_SP_ICR, 2);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
/* Test interrupt path by forcing a a software IRQ */
|
|
static int __devinit sky2_test_msi(struct sky2_hw *hw)
|
|
{
|
|
struct pci_dev *pdev = hw->pdev;
|
|
int err;
|
|
|
|
sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW);
|
|
|
|
err = request_irq(pdev->irq, sky2_test_intr, SA_SHIRQ, DRV_NAME, hw);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
|
|
pci_name(pdev), pdev->irq);
|
|
return err;
|
|
}
|
|
|
|
init_waitqueue_head (&hw->msi_wait);
|
|
|
|
sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ);
|
|
wmb();
|
|
|
|
wait_event_timeout(hw->msi_wait, hw->msi_detected, HZ/10);
|
|
|
|
if (!hw->msi_detected) {
|
|
/* MSI test failed, go back to INTx mode */
|
|
printk(KERN_WARNING PFX "%s: No interrupt was generated using MSI, "
|
|
"switching to INTx mode. Please report this failure to "
|
|
"the PCI maintainer and include system chipset information.\n",
|
|
pci_name(pdev));
|
|
|
|
err = -EOPNOTSUPP;
|
|
sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ);
|
|
}
|
|
|
|
sky2_write32(hw, B0_IMSK, 0);
|
|
|
|
free_irq(pdev->irq, hw);
|
|
|
|
return err;
|
|
}
|
|
|
|
static int __devinit sky2_probe(struct pci_dev *pdev,
|
|
const struct pci_device_id *ent)
|
|
{
|
|
struct net_device *dev, *dev1 = NULL;
|
|
struct sky2_hw *hw;
|
|
int err, pm_cap, using_dac = 0;
|
|
|
|
err = pci_enable_device(pdev);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s cannot enable PCI device\n",
|
|
pci_name(pdev));
|
|
goto err_out;
|
|
}
|
|
|
|
err = pci_request_regions(pdev, DRV_NAME);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
|
|
pci_name(pdev));
|
|
goto err_out;
|
|
}
|
|
|
|
pci_set_master(pdev);
|
|
|
|
/* Find power-management capability. */
|
|
pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
|
|
if (pm_cap == 0) {
|
|
printk(KERN_ERR PFX "Cannot find PowerManagement capability, "
|
|
"aborting.\n");
|
|
err = -EIO;
|
|
goto err_out_free_regions;
|
|
}
|
|
|
|
if (sizeof(dma_addr_t) > sizeof(u32) &&
|
|
!(err = pci_set_dma_mask(pdev, DMA_64BIT_MASK))) {
|
|
using_dac = 1;
|
|
err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
|
|
if (err < 0) {
|
|
printk(KERN_ERR PFX "%s unable to obtain 64 bit DMA "
|
|
"for consistent allocations\n", pci_name(pdev));
|
|
goto err_out_free_regions;
|
|
}
|
|
|
|
} else {
|
|
err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s no usable DMA configuration\n",
|
|
pci_name(pdev));
|
|
goto err_out_free_regions;
|
|
}
|
|
}
|
|
|
|
err = -ENOMEM;
|
|
hw = kzalloc(sizeof(*hw), GFP_KERNEL);
|
|
if (!hw) {
|
|
printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
|
|
pci_name(pdev));
|
|
goto err_out_free_regions;
|
|
}
|
|
|
|
hw->pdev = pdev;
|
|
|
|
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
|
|
if (!hw->regs) {
|
|
printk(KERN_ERR PFX "%s: cannot map device registers\n",
|
|
pci_name(pdev));
|
|
goto err_out_free_hw;
|
|
}
|
|
hw->pm_cap = pm_cap;
|
|
|
|
#ifdef __BIG_ENDIAN
|
|
/* byte swap descriptors in hardware */
|
|
{
|
|
u32 reg;
|
|
|
|
reg = sky2_pci_read32(hw, PCI_DEV_REG2);
|
|
reg |= PCI_REV_DESC;
|
|
sky2_pci_write32(hw, PCI_DEV_REG2, reg);
|
|
}
|
|
#endif
|
|
|
|
/* ring for status responses */
|
|
hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
|
|
&hw->st_dma);
|
|
if (!hw->st_le)
|
|
goto err_out_iounmap;
|
|
|
|
err = sky2_reset(hw);
|
|
if (err)
|
|
goto err_out_iounmap;
|
|
|
|
printk(KERN_INFO PFX "v%s addr 0x%lx irq %d Yukon-%s (0x%x) rev %d\n",
|
|
DRV_VERSION, pci_resource_start(pdev, 0), pdev->irq,
|
|
yukon2_name[hw->chip_id - CHIP_ID_YUKON_XL],
|
|
hw->chip_id, hw->chip_rev);
|
|
|
|
dev = sky2_init_netdev(hw, 0, using_dac);
|
|
if (!dev)
|
|
goto err_out_free_pci;
|
|
|
|
err = register_netdev(dev);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s: cannot register net device\n",
|
|
pci_name(pdev));
|
|
goto err_out_free_netdev;
|
|
}
|
|
|
|
sky2_show_addr(dev);
|
|
|
|
if (hw->ports > 1 && (dev1 = sky2_init_netdev(hw, 1, using_dac))) {
|
|
if (register_netdev(dev1) == 0)
|
|
sky2_show_addr(dev1);
|
|
else {
|
|
/* Failure to register second port need not be fatal */
|
|
printk(KERN_WARNING PFX
|
|
"register of second port failed\n");
|
|
hw->dev[1] = NULL;
|
|
free_netdev(dev1);
|
|
}
|
|
}
|
|
|
|
if (!disable_msi && pci_enable_msi(pdev) == 0) {
|
|
err = sky2_test_msi(hw);
|
|
if (err == -EOPNOTSUPP)
|
|
pci_disable_msi(pdev);
|
|
else if (err)
|
|
goto err_out_unregister;
|
|
}
|
|
|
|
err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
|
|
pci_name(pdev), pdev->irq);
|
|
goto err_out_unregister;
|
|
}
|
|
|
|
sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
|
|
|
|
pci_set_drvdata(pdev, hw);
|
|
|
|
return 0;
|
|
|
|
err_out_unregister:
|
|
pci_disable_msi(pdev);
|
|
if (dev1) {
|
|
unregister_netdev(dev1);
|
|
free_netdev(dev1);
|
|
}
|
|
unregister_netdev(dev);
|
|
err_out_free_netdev:
|
|
free_netdev(dev);
|
|
err_out_free_pci:
|
|
sky2_write8(hw, B0_CTST, CS_RST_SET);
|
|
pci_free_consistent(hw->pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
|
|
err_out_iounmap:
|
|
iounmap(hw->regs);
|
|
err_out_free_hw:
|
|
kfree(hw);
|
|
err_out_free_regions:
|
|
pci_release_regions(pdev);
|
|
pci_disable_device(pdev);
|
|
err_out:
|
|
return err;
|
|
}
|
|
|
|
static void __devexit sky2_remove(struct pci_dev *pdev)
|
|
{
|
|
struct sky2_hw *hw = pci_get_drvdata(pdev);
|
|
struct net_device *dev0, *dev1;
|
|
|
|
if (!hw)
|
|
return;
|
|
|
|
dev0 = hw->dev[0];
|
|
dev1 = hw->dev[1];
|
|
if (dev1)
|
|
unregister_netdev(dev1);
|
|
unregister_netdev(dev0);
|
|
|
|
sky2_write32(hw, B0_IMSK, 0);
|
|
sky2_set_power_state(hw, PCI_D3hot);
|
|
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
|
|
sky2_write8(hw, B0_CTST, CS_RST_SET);
|
|
sky2_read8(hw, B0_CTST);
|
|
|
|
free_irq(pdev->irq, hw);
|
|
pci_disable_msi(pdev);
|
|
pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
|
|
pci_release_regions(pdev);
|
|
pci_disable_device(pdev);
|
|
|
|
if (dev1)
|
|
free_netdev(dev1);
|
|
free_netdev(dev0);
|
|
iounmap(hw->regs);
|
|
kfree(hw);
|
|
|
|
pci_set_drvdata(pdev, NULL);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
|
|
{
|
|
struct sky2_hw *hw = pci_get_drvdata(pdev);
|
|
int i;
|
|
|
|
for (i = 0; i < 2; i++) {
|
|
struct net_device *dev = hw->dev[i];
|
|
|
|
if (dev) {
|
|
if (!netif_running(dev))
|
|
continue;
|
|
|
|
sky2_down(dev);
|
|
netif_device_detach(dev);
|
|
}
|
|
}
|
|
|
|
return sky2_set_power_state(hw, pci_choose_state(pdev, state));
|
|
}
|
|
|
|
static int sky2_resume(struct pci_dev *pdev)
|
|
{
|
|
struct sky2_hw *hw = pci_get_drvdata(pdev);
|
|
int i, err;
|
|
|
|
pci_restore_state(pdev);
|
|
pci_enable_wake(pdev, PCI_D0, 0);
|
|
err = sky2_set_power_state(hw, PCI_D0);
|
|
if (err)
|
|
goto out;
|
|
|
|
err = sky2_reset(hw);
|
|
if (err)
|
|
goto out;
|
|
|
|
for (i = 0; i < 2; i++) {
|
|
struct net_device *dev = hw->dev[i];
|
|
if (dev && netif_running(dev)) {
|
|
netif_device_attach(dev);
|
|
err = sky2_up(dev);
|
|
if (err) {
|
|
printk(KERN_ERR PFX "%s: could not up: %d\n",
|
|
dev->name, err);
|
|
dev_close(dev);
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
out:
|
|
return err;
|
|
}
|
|
#endif
|
|
|
|
static struct pci_driver sky2_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = sky2_id_table,
|
|
.probe = sky2_probe,
|
|
.remove = __devexit_p(sky2_remove),
|
|
#ifdef CONFIG_PM
|
|
.suspend = sky2_suspend,
|
|
.resume = sky2_resume,
|
|
#endif
|
|
};
|
|
|
|
static int __init sky2_init_module(void)
|
|
{
|
|
return pci_register_driver(&sky2_driver);
|
|
}
|
|
|
|
static void __exit sky2_cleanup_module(void)
|
|
{
|
|
pci_unregister_driver(&sky2_driver);
|
|
}
|
|
|
|
module_init(sky2_init_module);
|
|
module_exit(sky2_cleanup_module);
|
|
|
|
MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
|
|
MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_VERSION(DRV_VERSION);
|