Techwizz/kernel-fxtec-pro1x
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
kernel-fxtec-pro1x/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
Ben Cahill 483fd7e5ff iwlwifi: document Tx registers 
Document Tx registers

Clean up unused definitions

Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:05:30 -08:00

1693 lines
64 KiB
C
Raw Blame History

/******************************************************************************
*
* This file is provided under a dual BSD/GPLv2 license. When using or
* redistributing this file, you may do so under either license.
*
* GPL LICENSE SUMMARY
*
* Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
* USA
*
* The full GNU General Public License is included in this distribution
* in the file called LICENSE.GPL.
*
* Contact Information:
* James P. Ketrenos <ipw2100-admin@linux.intel.com>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*
* BSD LICENSE
*
* Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name Intel Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*****************************************************************************/
/*
* Please use this file (iwl-4965-hw.h) only for hardware-related definitions.
* Use iwl-4965-commands.h for uCode API definitions.
* Use iwl-4965.h for driver implementation definitions.
*/
#ifndef __iwl_4965_hw_h__
#define __iwl_4965_hw_h__
/*
* uCode queue management definitions ...
* Queue #4 is the command queue for 3945 and 4965; map it to Tx FIFO chnl 4.
* The first queue used for block-ack aggregation is #7 (4965 only).
* All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
*/
#define IWL_CMD_QUEUE_NUM 4
#define IWL_CMD_FIFO_NUM 4
#define IWL_BACK_QUEUE_FIRST_ID 7
/* Tx rates */
#define IWL_CCK_RATES 4
#define IWL_OFDM_RATES 8
#define IWL_HT_RATES 16
#define IWL_MAX_RATES (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)
/* Time constants */
#define SHORT_SLOT_TIME 9
#define LONG_SLOT_TIME 20
/* RSSI to dBm */
#define IWL_RSSI_OFFSET 44
/*
* EEPROM related constants, enums, and structures.
*/
/*
* EEPROM access time values:
*
* Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
* then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
* CSR_EEPROM_REG_BIT_CMD (0x2).
* Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
* When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
* Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
*/
#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
/*
* Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
*
* IBSS and/or AP operation is allowed *only* on those channels with
* (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
* RADAR detection is not supported by the 4965 driver, but is a
* requirement for establishing a new network for legal operation on channels
* requiring RADAR detection or restricting ACTIVE scanning.
*
* NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
* It only indicates that 20 MHz channel use is supported; FAT channel
* usage is indicated by a separate set of regulatory flags for each
* FAT channel pair.
*
* NOTE: Using a channel inappropriately will result in a uCode error!
*/
enum {
EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
/* Bit 2 Reserved */
EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */
EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
};
/* SKU Capabilities */
#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
/* *regulatory* channel data format in eeprom, one for each channel.
* There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
struct iwl4965_eeprom_channel {
u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
} __attribute__ ((packed));
/* 4965 has two radio transmitters (and 3 radio receivers) */
#define EEPROM_TX_POWER_TX_CHAINS (2)
/* 4965 has room for up to 8 sets of txpower calibration data */
#define EEPROM_TX_POWER_BANDS (8)
/* 4965 factory calibration measures txpower gain settings for
* each of 3 target output levels */
#define EEPROM_TX_POWER_MEASUREMENTS (3)
/* 4965 driver does not work with txpower calibration version < 5.
* Look for this in calib_version member of struct iwl4965_eeprom. */
#define EEPROM_TX_POWER_VERSION_NEW (5)
/*
* 4965 factory calibration data for one txpower level, on one channel,
* measured on one of the 2 tx chains (radio transmitter and associated
* antenna). EEPROM contains:
*
* 1) Temperature (degrees Celsius) of device when measurement was made.
*
* 2) Gain table index used to achieve the target measurement power.
* This refers to the "well-known" gain tables (see iwl-4965-hw.h).
*
* 3) Actual measured output power, in half-dBm ("34" = 17 dBm).
*
* 4) RF power amplifier detector level measurement (not used).
*/
struct iwl4965_eeprom_calib_measure {
u8 temperature; /* Device temperature (Celsius) */
u8 gain_idx; /* Index into gain table */
u8 actual_pow; /* Measured RF output power, half-dBm */
s8 pa_det; /* Power amp detector level (not used) */
} __attribute__ ((packed));
/*
* 4965 measurement set for one channel. EEPROM contains:
*
* 1) Channel number measured
*
* 2) Measurements for each of 3 power levels for each of 2 radio transmitters
* (a.k.a. "tx chains") (6 measurements altogether)
*/
struct iwl4965_eeprom_calib_ch_info {
u8 ch_num;
struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS]
[EEPROM_TX_POWER_MEASUREMENTS];
} __attribute__ ((packed));
/*
* 4965 txpower subband info.
*
* For each frequency subband, EEPROM contains the following:
*
* 1) First and last channels within range of the subband. "0" values
* indicate that this sample set is not being used.
*
* 2) Sample measurement sets for 2 channels close to the range endpoints.
*/
struct iwl4965_eeprom_calib_subband_info {
u8 ch_from; /* channel number of lowest channel in subband */
u8 ch_to; /* channel number of highest channel in subband */
struct iwl4965_eeprom_calib_ch_info ch1;
struct iwl4965_eeprom_calib_ch_info ch2;
} __attribute__ ((packed));
/*
* 4965 txpower calibration info. EEPROM contains:
*
* 1) Factory-measured saturation power levels (maximum levels at which
* tx power amplifier can output a signal without too much distortion).
* There is one level for 2.4 GHz band and one for 5 GHz band. These
* values apply to all channels within each of the bands.
*
* 2) Factory-measured power supply voltage level. This is assumed to be
* constant (i.e. same value applies to all channels/bands) while the
* factory measurements are being made.
*
* 3) Up to 8 sets of factory-measured txpower calibration values.
* These are for different frequency ranges, since txpower gain
* characteristics of the analog radio circuitry vary with frequency.
*
* Not all sets need to be filled with data;
* struct iwl4965_eeprom_calib_subband_info contains range of channels
* (0 if unused) for each set of data.
*/
struct iwl4965_eeprom_calib_info {
u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
u8 saturation_power52; /* half-dBm */
s16 voltage; /* signed */
struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS];
} __attribute__ ((packed));
/*
* 4965 EEPROM map
*/
struct iwl4965_eeprom {
u8 reserved0[16];
#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
u16 device_id; /* abs.ofs: 16 */
u8 reserved1[2];
#define EEPROM_PMC (2*0x0A) /* 2 bytes */
u16 pmc; /* abs.ofs: 20 */
u8 reserved2[20];
#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
u8 mac_address[6]; /* abs.ofs: 42 */
u8 reserved3[58];
#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
u16 board_revision; /* abs.ofs: 106 */
u8 reserved4[11];
#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
u8 board_pba_number[9]; /* abs.ofs: 119 */
u8 reserved5[8];
#define EEPROM_VERSION (2*0x44) /* 2 bytes */
u16 version; /* abs.ofs: 136 */
#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
u8 sku_cap; /* abs.ofs: 138 */
#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
u8 leds_mode; /* abs.ofs: 139 */
#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
u16 oem_mode;
#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
u16 wowlan_mode; /* abs.ofs: 142 */
#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
u16 leds_time_interval; /* abs.ofs: 144 */
#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
u8 leds_off_time; /* abs.ofs: 146 */
#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
u8 leds_on_time; /* abs.ofs: 147 */
#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
u8 almgor_m_version; /* abs.ofs: 148 */
#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
u8 antenna_switch_type; /* abs.ofs: 149 */
u8 reserved6[8];
#define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */
u16 board_revision_4965; /* abs.ofs: 158 */
u8 reserved7[13];
#define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */
u8 board_pba_number_4965[9]; /* abs.ofs: 173 */
u8 reserved8[10];
#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
u8 sku_id[4]; /* abs.ofs: 192 */
/*
* Per-channel regulatory data.
*
* Each channel that *might* be supported by 3945 or 4965 has a fixed location
* in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
* txpower (MSB).
*
* Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
* channels (only for 4965, not supported by 3945) appear later in the EEPROM.
*
* 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
*/
#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
u16 band_1_count; /* abs.ofs: 196 */
#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
/*
* 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
* 5.0 GHz channels 7, 8, 11, 12, 16
* (4915-5080MHz) (none of these is ever supported)
*/
#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
u16 band_2_count; /* abs.ofs: 226 */
#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
/*
* 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
* (5170-5320MHz)
*/
#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
u16 band_3_count; /* abs.ofs: 254 */
#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
/*
* 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
* (5500-5700MHz)
*/
#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */
u16 band_4_count; /* abs.ofs: 280 */
#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */
struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
/*
* 5.7 GHz channels 145, 149, 153, 157, 161, 165
* (5725-5825MHz)
*/
#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */
u16 band_5_count; /* abs.ofs: 304 */
#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
u8 reserved10[2];
/*
* 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
*
* The channel listed is the center of the lower 20 MHz half of the channel.
* The overall center frequency is actually 2 channels (10 MHz) above that,
* and the upper half of each FAT channel is centered 4 channels (20 MHz) away
* from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
* and the overall FAT channel width centers on channel 3.
*
* NOTE: The RXON command uses 20 MHz channel numbers to specify the
* control channel to which to tune. RXON also specifies whether the
* control channel is the upper or lower half of a FAT channel.
*
* NOTE: 4965 does not support FAT channels on 2.4 GHz.
*/
#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */
struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */
u8 reserved11[2];
/*
* 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
* 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
*/
#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */
struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */
u8 reserved12[6];
/*
* 4965 driver requires txpower calibration format version 5 or greater.
* Driver does not work with txpower calibration version < 5.
* This value is simply a 16-bit number, no major/minor versions here.
*/
#define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */
u16 calib_version; /* abs.ofs: 364 */
u8 reserved13[2];
u8 reserved14[96]; /* abs.ofs: 368 */
/*
* 4965 Txpower calibration data.
*/
#define EEPROM_IWL_CALIB_TXPOWER_OFFSET (2*0xE8) /* 48 bytes */
struct iwl4965_eeprom_calib_info calib_info; /* abs.ofs: 464 */
u8 reserved16[140]; /* fill out to full 1024 byte block */
} __attribute__ ((packed));
#define IWL_EEPROM_IMAGE_SIZE 1024
/* End of EEPROM */
#include "iwl-4965-commands.h"
#define PCI_LINK_CTRL 0x0F0
#define PCI_POWER_SOURCE 0x0C8
#define PCI_REG_WUM8 0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
/*=== CSR (control and status registers) ===*/
#define CSR_BASE (0x000)
#define CSR_SW_VER (CSR_BASE+0x000)
#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
#define CSR_GP_CNTRL (CSR_BASE+0x024)
/*
* Hardware revision info
* Bit fields:
* 31-8: Reserved
* 7-4: Type of device: 0x0 = 4965, 0xd = 3945
* 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
* 1-0: "Dash" value, as in A-1, etc.
*
* NOTE: Revision step affects calculation of CCK txpower for 4965.
*/
#define CSR_HW_REV (CSR_BASE+0x028)
/* EEPROM reads */
#define CSR_EEPROM_REG (CSR_BASE+0x02c)
#define CSR_EEPROM_GP (CSR_BASE+0x030)
#define CSR_GP_UCODE (CSR_BASE+0x044)
#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
/*
* Indicates hardware rev, to determine CCK backoff for txpower calculation.
* Bit fields:
* 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
*/
#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
* acknowledged (reset) by host writing "1" to flagged bits. */
#define CSR_INT_BIT_FH_RX (1<<31) /* Rx DMA, cmd responses, FH_INT[17:16] */
#define CSR_INT_BIT_HW_ERR (1<<29) /* DMA hardware error FH_INT[31] */
#define CSR_INT_BIT_DNLD (1<<28) /* uCode Download */
#define CSR_INT_BIT_FH_TX (1<<27) /* Tx DMA FH_INT[1:0] */
#define CSR_INT_BIT_MAC_CLK_ACTV (1<<26) /* NIC controller's clock toggled on/off */
#define CSR_INT_BIT_SW_ERR (1<<25) /* uCode error */
#define CSR_INT_BIT_RF_KILL (1<<7) /* HW RFKILL switch GP_CNTRL[27] toggled */
#define CSR_INT_BIT_CT_KILL (1<<6) /* Critical temp (chip too hot) rfkill */
#define CSR_INT_BIT_SW_RX (1<<3) /* Rx, command responses, 3945 */
#define CSR_INT_BIT_WAKEUP (1<<1) /* NIC controller waking up (pwr mgmt) */
#define CSR_INT_BIT_ALIVE (1<<0) /* uCode interrupts once it initializes */
#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
CSR_INT_BIT_HW_ERR | \
CSR_INT_BIT_FH_TX | \
CSR_INT_BIT_SW_ERR | \
CSR_INT_BIT_RF_KILL | \
CSR_INT_BIT_SW_RX | \
CSR_INT_BIT_WAKEUP | \
CSR_INT_BIT_ALIVE)
/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
#define CSR_FH_INT_BIT_ERR (1<<31) /* Error */
#define CSR_FH_INT_BIT_HI_PRIOR (1<<30) /* High priority Rx, bypass coalescing */
#define CSR_FH_INT_BIT_RX_CHNL1 (1<<17) /* Rx channel 1 */
#define CSR_FH_INT_BIT_RX_CHNL0 (1<<16) /* Rx channel 0 */
#define CSR_FH_INT_BIT_TX_CHNL1 (1<<1) /* Tx channel 1 */
#define CSR_FH_INT_BIT_TX_CHNL0 (1<<0) /* Tx channel 0 */
#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
CSR_FH_INT_BIT_RX_CHNL1 | \
CSR_FH_INT_BIT_RX_CHNL0)
#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
CSR_FH_INT_BIT_TX_CHNL0)
/* RESET */
#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
/* GP (general purpose) CONTROL */
#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
/* EEPROM REG */
#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
/* EEPROM GP */
#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
/* UCODE DRV GP */
#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
/* GPIO */
#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
/* GI Chicken Bits */
#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE (0x400)
/*
* Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
* structures, error log, event log, verifying uCode load).
* First write to address register, then read from or write to data register
* to complete the job. Once the address register is set up, accesses to
* data registers auto-increment the address by one dword.
* Bit usage for address registers (read or write):
* 0-31: memory address within device
*/
#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
/*
* Registers for accessing device's internal peripheral registers
* (e.g. SCD, BSM, etc.). First write to address register,
* then read from or write to data register to complete the job.
* Bit usage for address registers (read or write):
* 0-15: register address (offset) within device
* 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
*/
#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
/*
* Per-Tx-queue write pointer (index, really!) (3945 and 4965).
* Driver sets this to indicate index to next TFD that driver will fill
* (1 past latest filled).
* Bit usage:
* 0-7: queue write index (0-255)
* 11-8: queue selector (0-15)
*/
#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
#define TFD_QUEUE_SIZE_MAX (256)
#define IWL_NUM_SCAN_RATES (2)
#define IWL_DEFAULT_TX_RETRY 15
#define RX_QUEUE_SIZE 256
#define RX_QUEUE_MASK 255
#define RX_QUEUE_SIZE_LOG 8
#define TFD_TX_CMD_SLOTS 256
#define TFD_CMD_SLOTS 32
#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl4965_cmd) - \
sizeof(struct iwl4965_cmd_meta))
/*
* RX related structures and functions
*/
#define RX_FREE_BUFFERS 64
#define RX_LOW_WATERMARK 8
/* Size of one Rx buffer in host DRAM */
#define IWL_RX_BUF_SIZE (4 * 1024)
/* Sizes and addresses for instruction and data memory (SRAM) in
* 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */
#define RTC_INST_LOWER_BOUND (0x000000)
#define KDR_RTC_INST_UPPER_BOUND (0x018000)
#define RTC_DATA_LOWER_BOUND (0x800000)
#define KDR_RTC_DATA_UPPER_BOUND (0x80A000)
#define KDR_RTC_INST_SIZE (KDR_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
#define KDR_RTC_DATA_SIZE (KDR_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
#define IWL_MAX_INST_SIZE KDR_RTC_INST_SIZE
#define IWL_MAX_DATA_SIZE KDR_RTC_DATA_SIZE
/* Size of uCode instruction memory in bootstrap state machine */
#define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE
static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
{
return (addr >= RTC_DATA_LOWER_BOUND) &&
(addr < KDR_RTC_DATA_UPPER_BOUND);
}
/********************* START TEMPERATURE *************************************/
/**
* 4965 temperature calculation.
*
* The driver must calculate the device temperature before calculating
* a txpower setting (amplifier gain is temperature dependent). The
* calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration
* values used for the life of the driver, and one of which (R4) is the
* real-time temperature indicator.
*
* uCode provides all 4 values to the driver via the "initialize alive"
* notification (see struct iwl4965_init_alive_resp). After the runtime uCode
* image loads, uCode updates the R4 value via statistics notifications
* (see STATISTICS_NOTIFICATION), which occur after each received beacon
* when associated, or can be requested via REPLY_STATISTICS_CMD.
*
* NOTE: uCode provides the R4 value as a 23-bit signed value. Driver
* must sign-extend to 32 bits before applying formula below.
*
* Formula:
*
* degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8
*
* NOTE: The basic formula is 259 * (R4-R2) / (R3-R1). The 97/100 is
* an additional correction, which should be centered around 0 degrees
* Celsius (273 degrees Kelvin). The 8 (3 percent of 273) compensates for
* centering the 97/100 correction around 0 degrees K.
*
* Add 273 to Kelvin value to find degrees Celsius, for comparing current
* temperature with factory-measured temperatures when calculating txpower
* settings.
*/
#define TEMPERATURE_CALIB_KELVIN_OFFSET 8
#define TEMPERATURE_CALIB_A_VAL 259
/* Limit range of calculated temperature to be between these Kelvin values */
#define IWL_TX_POWER_TEMPERATURE_MIN (263)
#define IWL_TX_POWER_TEMPERATURE_MAX (410)
#define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \
(((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
((t) > IWL_TX_POWER_TEMPERATURE_MAX))
/********************* END TEMPERATURE ***************************************/
/********************* START TXPOWER *****************************************/
/**
* 4965 txpower calculations rely on information from three sources:
*
* 1) EEPROM
* 2) "initialize" alive notification
* 3) statistics notifications
*
* EEPROM data consists of:
*
* 1) Regulatory information (max txpower and channel usage flags) is provided
* separately for each channel that can possibly supported by 4965.
* 40 MHz wide (.11n fat) channels are listed separately from 20 MHz
* (legacy) channels.
*
* See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom
* for locations in EEPROM.
*
* 2) Factory txpower calibration information is provided separately for
* sub-bands of contiguous channels. 2.4GHz has just one sub-band,
* but 5 GHz has several sub-bands.
*
* In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided.
*
* See struct iwl4965_eeprom_calib_info (and the tree of structures
* contained within it) for format, and struct iwl4965_eeprom for
* locations in EEPROM.
*
* "Initialization alive" notification (see struct iwl4965_init_alive_resp)
* consists of:
*
* 1) Temperature calculation parameters.
*
* 2) Power supply voltage measurement.
*
* 3) Tx gain compensation to balance 2 transmitters for MIMO use.
*
* Statistics notifications deliver:
*
* 1) Current values for temperature param R4.
*/
/**
* To calculate a txpower setting for a given desired target txpower, channel,
* modulation bit rate, and transmitter chain (4965 has 2 transmitters to
* support MIMO and transmit diversity), driver must do the following:
*
* 1) Compare desired txpower vs. (EEPROM) regulatory limit for this channel.
* Do not exceed regulatory limit; reduce target txpower if necessary.
*
* If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
* 2 transmitters will be used simultaneously; driver must reduce the
* regulatory limit by 3 dB (half-power) for each transmitter, so the
* combined total output of the 2 transmitters is within regulatory limits.
*
*
* 2) Compare target txpower vs. (EEPROM) saturation txpower *reduced by
* backoff for this bit rate*. Do not exceed (saturation - backoff[rate]);
* reduce target txpower if necessary.
*
* Backoff values below are in 1/2 dB units (equivalent to steps in
* txpower gain tables):
*
* OFDM 6 - 36 MBit: 10 steps (5 dB)
* OFDM 48 MBit: 15 steps (7.5 dB)
* OFDM 54 MBit: 17 steps (8.5 dB)
* OFDM 60 MBit: 20 steps (10 dB)
* CCK all rates: 10 steps (5 dB)
*
* Backoff values apply to saturation txpower on a per-transmitter basis;
* when using MIMO (2 transmitters), each transmitter uses the same
* saturation level provided in EEPROM, and the same backoff values;
* no reduction (such as with regulatory txpower limits) is required.
*
* Saturation and Backoff values apply equally to 20 Mhz (legacy) channel
* widths and 40 Mhz (.11n fat) channel widths; there is no separate
* factory measurement for fat channels.
*
* The result of this step is the final target txpower. The rest of
* the steps figure out the proper settings for the device to achieve
* that target txpower.
*
*
* 3) Determine (EEPROM) calibration subband for the target channel, by
* comparing against first and last channels in each subband
* (see struct iwl4965_eeprom_calib_subband_info).
*
*
* 4) Linearly interpolate (EEPROM) factory calibration measurement sets,
* referencing the 2 factory-measured (sample) channels within the subband.
*
* Interpolation is based on difference between target channel's frequency
* and the sample channels' frequencies. Since channel numbers are based
* on frequency (5 MHz between each channel number), this is equivalent
* to interpolating based on channel number differences.
*
* Note that the sample channels may or may not be the channels at the
* edges of the subband. The target channel may be "outside" of the
* span of the sampled channels.
*
* Driver may choose the pair (for 2 Tx chains) of measurements (see
* struct iwl4965_eeprom_calib_ch_info) for which the actual measured
* txpower comes closest to the desired txpower. Usually, though,
* the middle set of measurements is closest to the regulatory limits,
* and is therefore a good choice for all txpower calculations (this
* assumes that high accuracy is needed for maximizing legal txpower,
* while lower txpower configurations do not need as much accuracy).
*
* Driver should interpolate both members of the chosen measurement pair,
* i.e. for both Tx chains (radio transmitters), unless the driver knows
* that only one of the chains will be used (e.g. only one tx antenna
* connected, but this should be unusual). The rate scaling algorithm
* switches antennas to find best performance, so both Tx chains will
* be used (although only one at a time) even for non-MIMO transmissions.
*
* Driver should interpolate factory values for temperature, gain table
* index, and actual power. The power amplifier detector values are
* not used by the driver.
*
* Sanity check: If the target channel happens to be one of the sample
* channels, the results should agree with the sample channel's
* measurements!
*
*
* 5) Find difference between desired txpower and (interpolated)
* factory-measured txpower. Using (interpolated) factory gain table index
* (shown elsewhere) as a starting point, adjust this index lower to
* increase txpower, or higher to decrease txpower, until the target
* txpower is reached. Each step in the gain table is 1/2 dB.
*
* For example, if factory measured txpower is 16 dBm, and target txpower
* is 13 dBm, add 6 steps to the factory gain index to reduce txpower
* by 3 dB.
*
*
* 6) Find difference between current device temperature and (interpolated)
* factory-measured temperature for sub-band. Factory values are in
* degrees Celsius. To calculate current temperature, see comments for
* "4965 temperature calculation".
*
* If current temperature is higher than factory temperature, driver must
* increase gain (lower gain table index), and vice versa.
*
* Temperature affects gain differently for different channels:
*
* 2.4 GHz all channels: 3.5 degrees per half-dB step
* 5 GHz channels 34-43: 4.5 degrees per half-dB step
* 5 GHz channels >= 44: 4.0 degrees per half-dB step
*
* NOTE: Temperature can increase rapidly when transmitting, especially
* with heavy traffic at high txpowers. Driver should update
* temperature calculations often under these conditions to
* maintain strong txpower in the face of rising temperature.
*
*
* 7) Find difference between current power supply voltage indicator
* (from "initialize alive") and factory-measured power supply voltage
* indicator (EEPROM).
*
* If the current voltage is higher (indicator is lower) than factory
* voltage, gain should be reduced (gain table index increased) by:
*
* (eeprom - current) / 7
*
* If the current voltage is lower (indicator is higher) than factory
* voltage, gain should be increased (gain table index decreased) by:
*
* 2 * (current - eeprom) / 7
*
* If number of index steps in either direction turns out to be > 2,
* something is wrong ... just use 0.
*
* NOTE: Voltage compensation is independent of band/channel.
*
* NOTE: "Initialize" uCode measures current voltage, which is assumed
* to be constant after this initial measurement. Voltage
* compensation for txpower (number of steps in gain table)
* may be calculated once and used until the next uCode bootload.
*
*
* 8) If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
* adjust txpower for each transmitter chain, so txpower is balanced
* between the two chains. There are 5 pairs of tx_atten[group][chain]
* values in "initialize alive", one pair for each of 5 channel ranges:
*
* Group 0: 5 GHz channel 34-43
* Group 1: 5 GHz channel 44-70
* Group 2: 5 GHz channel 71-124
* Group 3: 5 GHz channel 125-200
* Group 4: 2.4 GHz all channels
*
* Add the tx_atten[group][chain] value to the index for the target chain.
* The values are signed, but are in pairs of 0 and a non-negative number,
* so as to reduce gain (if necessary) of the "hotter" channel. This
* avoids any need to double-check for regulatory compliance after
* this step.
*
*
* 9) If setting up for a CCK rate, lower the gain by adding a CCK compensation
* value to the index:
*
* Hardware rev B: 9 steps (4.5 dB)
* Hardware rev C: 5 steps (2.5 dB)
*
* Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
* bits [3:2], 1 = B, 2 = C.
*
* NOTE: This compensation is in addition to any saturation backoff that
* might have been applied in an earlier step.
*
*
* 10) Select the gain table, based on band (2.4 vs 5 GHz).
*
* Limit the adjusted index to stay within the table!
*
*
* 11) Read gain table entries for DSP and radio gain, place into appropriate
* location(s) in command (struct iwl4965_txpowertable_cmd).
*/
/* Limit range of txpower output target to be between these values */
#define IWL_TX_POWER_TARGET_POWER_MIN (0) /* 0 dBm = 1 milliwatt */
#define IWL_TX_POWER_TARGET_POWER_MAX (16) /* 16 dBm */
/**
* When MIMO is used (2 transmitters operating simultaneously), driver should
* limit each transmitter to deliver a max of 3 dB below the regulatory limit
* for the device. That is, use half power for each transmitter, so total
* txpower is within regulatory limits.
*
* The value "6" represents number of steps in gain table to reduce power 3 dB.
* Each step is 1/2 dB.
*/
#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
/**
* CCK gain compensation.
*
* When calculating txpowers for CCK, after making sure that the target power
* is within regulatory and saturation limits, driver must additionally
* back off gain by adding these values to the gain table index.
*
* Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
* bits [3:2], 1 = B, 2 = C.
*/
#define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9)
#define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5)
/*
* 4965 power supply voltage compensation for txpower
*/
#define TX_POWER_IWL_VOLTAGE_CODES_PER_03V (7)
/**
* Gain tables.
*
* The following tables contain pair of values for setting txpower, i.e.
* gain settings for the output of the device's digital signal processor (DSP),
* and for the analog gain structure of the transmitter.
*
* Each entry in the gain tables represents a step of 1/2 dB. Note that these
* are *relative* steps, not indications of absolute output power. Output
* power varies with temperature, voltage, and channel frequency, and also
* requires consideration of average power (to satisfy regulatory constraints),
* and peak power (to avoid distortion of the output signal).
*
* Each entry contains two values:
* 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
* linear value that multiplies the output of the digital signal processor,
* before being sent to the analog radio.
* 2) Radio gain. This sets the analog gain of the radio Tx path.
* It is a coarser setting, and behaves in a logarithmic (dB) fashion.
*
* EEPROM contains factory calibration data for txpower. This maps actual
* measured txpower levels to gain settings in the "well known" tables
* below ("well-known" means here that both factory calibration *and* the
* driver work with the same table).
*
* There are separate tables for 2.4 GHz and 5 GHz bands. The 5 GHz table
* has an extension (into negative indexes), in case the driver needs to
* boost power setting for high device temperatures (higher than would be
* present during factory calibration). A 5 Ghz EEPROM index of "40"
* corresponds to the 49th entry in the table used by the driver.
*/
#define MIN_TX_GAIN_INDEX (0) /* highest gain, lowest idx, 2.4 */
#define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9) /* highest gain, lowest idx, 5 */
/**
* 2.4 GHz gain table
*
* Index Dsp gain Radio gain
* 0 110 0x3f (highest gain)
* 1 104 0x3f
* 2 98 0x3f
* 3 110 0x3e
* 4 104 0x3e
* 5 98 0x3e
* 6 110 0x3d
* 7 104 0x3d
* 8 98 0x3d
* 9 110 0x3c
* 10 104 0x3c
* 11 98 0x3c
* 12 110 0x3b
* 13 104 0x3b
* 14 98 0x3b
* 15 110 0x3a
* 16 104 0x3a
* 17 98 0x3a
* 18 110 0x39
* 19 104 0x39
* 20 98 0x39
* 21 110 0x38
* 22 104 0x38
* 23 98 0x38
* 24 110 0x37
* 25 104 0x37
* 26 98 0x37
* 27 110 0x36
* 28 104 0x36
* 29 98 0x36
* 30 110 0x35
* 31 104 0x35
* 32 98 0x35
* 33 110 0x34
* 34 104 0x34
* 35 98 0x34
* 36 110 0x33
* 37 104 0x33
* 38 98 0x33
* 39 110 0x32
* 40 104 0x32
* 41 98 0x32
* 42 110 0x31
* 43 104 0x31
* 44 98 0x31
* 45 110 0x30
* 46 104 0x30
* 47 98 0x30
* 48 110 0x6
* 49 104 0x6
* 50 98 0x6
* 51 110 0x5
* 52 104 0x5
* 53 98 0x5
* 54 110 0x4
* 55 104 0x4
* 56 98 0x4
* 57 110 0x3
* 58 104 0x3
* 59 98 0x3
* 60 110 0x2
* 61 104 0x2
* 62 98 0x2
* 63 110 0x1
* 64 104 0x1
* 65 98 0x1
* 66 110 0x0
* 67 104 0x0
* 68 98 0x0
* 69 97 0
* 70 96 0
* 71 95 0
* 72 94 0
* 73 93 0
* 74 92 0
* 75 91 0
* 76 90 0
* 77 89 0
* 78 88 0
* 79 87 0
* 80 86 0
* 81 85 0
* 82 84 0
* 83 83 0
* 84 82 0
* 85 81 0
* 86 80 0
* 87 79 0
* 88 78 0
* 89 77 0
* 90 76 0
* 91 75 0
* 92 74 0
* 93 73 0
* 94 72 0
* 95 71 0
* 96 70 0
* 97 69 0
* 98 68 0
*/
/**
* 5 GHz gain table
*
* Index Dsp gain Radio gain
* -9 123 0x3F (highest gain)
* -8 117 0x3F
* -7 110 0x3F
* -6 104 0x3F
* -5 98 0x3F
* -4 110 0x3E
* -3 104 0x3E
* -2 98 0x3E
* -1 110 0x3D
* 0 104 0x3D
* 1 98 0x3D
* 2 110 0x3C
* 3 104 0x3C
* 4 98 0x3C
* 5 110 0x3B
* 6 104 0x3B
* 7 98 0x3B
* 8 110 0x3A
* 9 104 0x3A
* 10 98 0x3A
* 11 110 0x39
* 12 104 0x39
* 13 98 0x39
* 14 110 0x38
* 15 104 0x38
* 16 98 0x38
* 17 110 0x37
* 18 104 0x37
* 19 98 0x37
* 20 110 0x36
* 21 104 0x36
* 22 98 0x36
* 23 110 0x35
* 24 104 0x35
* 25 98 0x35
* 26 110 0x34
* 27 104 0x34
* 28 98 0x34
* 29 110 0x33
* 30 104 0x33
* 31 98 0x33
* 32 110 0x32
* 33 104 0x32
* 34 98 0x32
* 35 110 0x31
* 36 104 0x31
* 37 98 0x31
* 38 110 0x30
* 39 104 0x30
* 40 98 0x30
* 41 110 0x25
* 42 104 0x25
* 43 98 0x25
* 44 110 0x24
* 45 104 0x24
* 46 98 0x24
* 47 110 0x23
* 48 104 0x23
* 49 98 0x23
* 50 110 0x22
* 51 104 0x18
* 52 98 0x18
* 53 110 0x17
* 54 104 0x17
* 55 98 0x17
* 56 110 0x16
* 57 104 0x16
* 58 98 0x16
* 59 110 0x15
* 60 104 0x15
* 61 98 0x15
* 62 110 0x14
* 63 104 0x14
* 64 98 0x14
* 65 110 0x13
* 66 104 0x13
* 67 98 0x13
* 68 110 0x12
* 69 104 0x08
* 70 98 0x08
* 71 110 0x07
* 72 104 0x07
* 73 98 0x07
* 74 110 0x06
* 75 104 0x06
* 76 98 0x06
* 77 110 0x05
* 78 104 0x05
* 79 98 0x05
* 80 110 0x04
* 81 104 0x04
* 82 98 0x04
* 83 110 0x03
* 84 104 0x03
* 85 98 0x03
* 86 110 0x02
* 87 104 0x02
* 88 98 0x02
* 89 110 0x01
* 90 104 0x01
* 91 98 0x01
* 92 110 0x00
* 93 104 0x00
* 94 98 0x00
* 95 93 0x00
* 96 88 0x00
* 97 83 0x00
* 98 78 0x00
*/
/**
* Sanity checks and default values for EEPROM regulatory levels.
* If EEPROM values fall outside MIN/MAX range, use default values.
*
* Regulatory limits refer to the maximum average txpower allowed by
* regulatory agencies in the geographies in which the device is meant
* to be operated. These limits are SKU-specific (i.e. geography-specific),
* and channel-specific; each channel has an individual regulatory limit
* listed in the EEPROM.
*
* Units are in half-dBm (i.e. "34" means 17 dBm).
*/
#define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34)
#define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34)
#define IWL_TX_POWER_REGULATORY_MIN (0)
#define IWL_TX_POWER_REGULATORY_MAX (34)
/**
* Sanity checks and default values for EEPROM saturation levels.
* If EEPROM values fall outside MIN/MAX range, use default values.
*
* Saturation is the highest level that the output power amplifier can produce
* without significant clipping distortion. This is a "peak" power level.
* Different types of modulation (i.e. various "rates", and OFDM vs. CCK)
* require differing amounts of backoff, relative to their average power output,
* in order to avoid clipping distortion.
*
* Driver must make sure that it is violating neither the saturation limit,
* nor the regulatory limit, when calculating Tx power settings for various
* rates.
*
* Units are in half-dBm (i.e. "38" means 19 dBm).
*/
#define IWL_TX_POWER_DEFAULT_SATURATION_24 (38)
#define IWL_TX_POWER_DEFAULT_SATURATION_52 (38)
#define IWL_TX_POWER_SATURATION_MIN (20)
#define IWL_TX_POWER_SATURATION_MAX (50)
/**
* Channel groups used for Tx Attenuation calibration (MIMO tx channel balance)
* and thermal Txpower calibration.
*
* When calculating txpower, driver must compensate for current device
* temperature; higher temperature requires higher gain. Driver must calculate
* current temperature (see "4965 temperature calculation"), then compare vs.
* factory calibration temperature in EEPROM; if current temperature is higher
* than factory temperature, driver must *increase* gain by proportions shown
* in table below. If current temperature is lower than factory, driver must
* *decrease* gain.
*
* Different frequency ranges require different compensation, as shown below.
*/
/* Group 0, 5.2 GHz ch 34-43: 4.5 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR1_FCH 34
#define CALIB_IWL_TX_ATTEN_GR1_LCH 43
/* Group 1, 5.3 GHz ch 44-70: 4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR2_FCH 44
#define CALIB_IWL_TX_ATTEN_GR2_LCH 70
/* Group 2, 5.5 GHz ch 71-124: 4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR3_FCH 71
#define CALIB_IWL_TX_ATTEN_GR3_LCH 124
/* Group 3, 5.7 GHz ch 125-200: 4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR4_FCH 125
#define CALIB_IWL_TX_ATTEN_GR4_LCH 200
/* Group 4, 2.4 GHz all channels: 3.5 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR5_FCH 1
#define CALIB_IWL_TX_ATTEN_GR5_LCH 20
enum {
CALIB_CH_GROUP_1 = 0,
CALIB_CH_GROUP_2 = 1,
CALIB_CH_GROUP_3 = 2,
CALIB_CH_GROUP_4 = 3,
CALIB_CH_GROUP_5 = 4,
CALIB_CH_GROUP_MAX
};
/********************* END TXPOWER *****************************************/
/****************************/
/* Flow Handler Definitions */
/****************************/
/**
* This I/O area is directly read/writable by driver (e.g. Linux uses writel())
* Addresses are offsets from device's PCI hardware base address.
*/
#define FH_MEM_LOWER_BOUND (0x1000)
#define FH_MEM_UPPER_BOUND (0x1EF0)
/**
* Keep-Warm (KW) buffer base address.
*
* Driver must allocate a 4KByte buffer that is used by 4965 for keeping the
* host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency
* DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host
* from going into a power-savings mode that would cause higher DRAM latency,
* and possible data over/under-runs, before all Tx/Rx is complete.
*
* Driver loads IWL_FH_KW_MEM_ADDR_REG with the physical address (bits 35:4)
* of the buffer, which must be 4K aligned. Once this is set up, the 4965
* automatically invokes keep-warm accesses when normal accesses might not
* be sufficient to maintain fast DRAM response.
*
* Bit fields:
* 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned
*/
#define IWL_FH_KW_MEM_ADDR_REG (FH_MEM_LOWER_BOUND + 0x97C)
/**
* TFD Circular Buffers Base (CBBC) addresses
*
* 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident
* circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs)
* (see struct iwl_tfd_frame). These 16 pointer registers are offset by 0x04
* bytes from one another. Each TFD circular buffer in DRAM must be 256-byte
* aligned (address bits 0-7 must be 0).
*
* Bit fields in each pointer register:
* 27-0: TFD CB physical base address [35:8], must be 256-byte aligned
*/
#define FH_MEM_CBBC_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0)
#define FH_MEM_CBBC_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xA10)
/* Find TFD CB base pointer for given queue (range 0-15). */
#define FH_MEM_CBBC_QUEUE(x) (FH_MEM_CBBC_LOWER_BOUND + (x) * 0x4)
/**
* Rx SRAM Control and Status Registers (RSCSR)
*
* These registers provide handshake between driver and 4965 for the Rx queue
* (this queue handles *all* command responses, notifications, Rx data, etc.
* sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx
* queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can
* concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer
* Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1
* mapping between RBDs and RBs.
*
* Driver must allocate host DRAM memory for the following, and set the
* physical address of each into 4965 registers:
*
* 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256
* entries (although any power of 2, up to 4096, is selectable by driver).
* Each entry (1 dword) points to a receive buffer (RB) of consistent size
* (typically 4K, although 8K or 16K are also selectable by driver).
* Driver sets up RB size and number of RBDs in the CB via Rx config
* register FH_MEM_RCSR_CHNL0_CONFIG_REG.
*
* Bit fields within one RBD:
* 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned
*
* Driver sets physical address [35:8] of base of RBD circular buffer
* into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0].
*
* 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers
* (RBs) have been filled, via a "write pointer", actually the index of
* the RB's corresponding RBD within the circular buffer. Driver sets
* physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0].
*
* Bit fields in lower dword of Rx status buffer (upper dword not used
* by driver; see struct iwl4965_shared, val0):
* 31-12: Not used by driver
* 11- 0: Index of last filled Rx buffer descriptor
* (4965 writes, driver reads this value)
*
* As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must
* enter pointers to these RBs into contiguous RBD circular buffer entries,
* and update the 4965's "write" index register, FH_RSCSR_CHNL0_RBDCB_WPTR_REG.
*
* This "write" index corresponds to the *next* RBD that the driver will make
* available, i.e. one RBD past the tail of the ready-to-fill RBDs within
* the circular buffer. This value should initially be 0 (before preparing any
* RBs), should be 8 after preparing the first 8 RBs (for example), and must
* wrap back to 0 at the end of the circular buffer (but don't wrap before
* "read" index has advanced past 1! See below).
* NOTE: 4965 EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8.
*
* As the 4965 fills RBs (referenced from contiguous RBDs within the circular
* buffer), it updates the Rx status buffer in host DRAM, 2) described above,
* to tell the driver the index of the latest filled RBD. The driver must
* read this "read" index from DRAM after receiving an Rx interrupt from 4965.
*
* The driver must also internally keep track of a third index, which is the
* next RBD to process. When receiving an Rx interrupt, driver should process
* all filled but unprocessed RBs up to, but not including, the RB
* corresponding to the "read" index. For example, if "read" index becomes "1",
* driver may process the RB pointed to by RBD 0. Depending on volume of
* traffic, there may be many RBs to process.
*
* If read index == write index, 4965 thinks there is no room to put new data.
* Due to this, the maximum number of filled RBs is 255, instead of 256. To
* be safe, make sure that there is a gap of at least 2 RBDs between "write"
* and "read" indexes; that is, make sure that there are no more than 254
* buffers waiting to be filled.
*/
#define FH_MEM_RSCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xBC0)
#define FH_MEM_RSCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RSCSR_CHNL0 (FH_MEM_RSCSR_LOWER_BOUND)
/**
* Physical base address of 8-byte Rx Status buffer.
* Bit fields:
* 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned.
*/
#define FH_RSCSR_CHNL0_STTS_WPTR_REG (FH_MEM_RSCSR_CHNL0)
/**
* Physical base address of Rx Buffer Descriptor Circular Buffer.
* Bit fields:
* 27-0: RBD CD physical base address [35:8], must be 256-byte aligned.
*/
#define FH_RSCSR_CHNL0_RBDCB_BASE_REG (FH_MEM_RSCSR_CHNL0 + 0x004)
/**
* Rx write pointer (index, really!).
* Bit fields:
* 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1.
* NOTE: For 256-entry circular buffer, use only bits [7:0].
*/
#define FH_RSCSR_CHNL0_RBDCB_WPTR_REG (FH_MEM_RSCSR_CHNL0 + 0x008)
#define FH_RSCSR_CHNL0_WPTR (FH_RSCSR_CHNL0_RBDCB_WPTR_REG)
/**
* Rx Config/Status Registers (RCSR)
* Rx Config Reg for channel 0 (only channel used)
*
* Driver must initialize FH_MEM_RCSR_CHNL0_CONFIG_REG as follows for
* normal operation (see bit fields).
*
* Clearing FH_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA.
* Driver should poll FH_MEM_RSSR_RX_STATUS_REG for
* FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing.
*
* Bit fields:
* 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame,
* '10' operate normally
* 29-24: reserved
* 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal),
* min "5" for 32 RBDs, max "12" for 4096 RBDs.
* 19-18: reserved
* 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K,
* '10' 12K, '11' 16K.
* 15-14: reserved
* 13-12: IRQ destination; '00' none, '01' host driver (normal operation)
* 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec)
* typical value 0x10 (about 1/2 msec)
* 3- 0: reserved
*/
#define FH_MEM_RCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xCC0)
#define FH_MEM_RCSR_CHNL0 (FH_MEM_RCSR_LOWER_BOUND)
#define FH_MEM_RCSR_CHNL0_CONFIG_REG (FH_MEM_RCSR_CHNL0)
#define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MASK (0x00000FF0) /* bit 4-11 */
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MASK (0x00001000) /* bit 12 */
#define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MASK (0x00008000) /* bit 15 */
#define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MASK (0x00030000) /* bits 16-17 */
#define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MASK (0x00F00000) /* bits 20-23 */
#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK (0xC0000000) /* bits 30-31 */
#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT (20)
#define FH_RCSR_RX_CONFIG_RB_SIZE_BITSHIFT (16)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000)
#define IWL_FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000)
/**
* Rx Shared Status Registers (RSSR)
*
* After stopping Rx DMA channel (writing 0 to FH_MEM_RCSR_CHNL0_CONFIG_REG),
* driver must poll FH_MEM_RSSR_RX_STATUS_REG until Rx channel is idle.
*
* Bit fields:
* 24: 1 = Channel 0 is idle
*
* FH_MEM_RSSR_SHARED_CTRL_REG and FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV contain
* default values that should not be altered by the driver.
*/
#define FH_MEM_RSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC40)
#define FH_MEM_RSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xD00)
#define FH_MEM_RSSR_SHARED_CTRL_REG (FH_MEM_RSSR_LOWER_BOUND)
#define FH_MEM_RSSR_RX_STATUS_REG (FH_MEM_RSSR_LOWER_BOUND + 0x004)
#define FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV (FH_MEM_RSSR_LOWER_BOUND + 0x008)
#define FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000)
/**
* Transmit DMA Channel Control/Status Registers (TCSR)
*
* 4965 has one configuration register for each of 8 Tx DMA/FIFO channels
* supported in hardware (don't confuse these with the 16 Tx queues in DRAM,
* which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes.
*
* To use a Tx DMA channel, driver must initialize its
* IWL_FH_TCSR_CHNL_TX_CONFIG_REG(chnl) with:
*
* IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE |
* IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL
*
* All other bits should be 0.
*
* Bit fields:
* 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame,
* '10' operate normally
* 29- 4: Reserved, set to "0"
* 3: Enable internal DMA requests (1, normal operation), disable (0)
* 2- 0: Reserved, set to "0"
*/
#define IWL_FH_TCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xD00)
#define IWL_FH_TCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xE60)
/* Find Control/Status reg for given Tx DMA/FIFO channel */
#define IWL_FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \
(IWL_FH_TCSR_LOWER_BOUND + 0x20 * _chnl)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE_VAL (0x00000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL (0x00000008)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000)
/**
* Tx Shared Status Registers (TSSR)
*
* After stopping Tx DMA channel (writing 0 to
* IWL_FH_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll
* IWL_FH_TSSR_TX_STATUS_REG until selected Tx channel is idle
* (channel's buffers empty | no pending requests).
*
* Bit fields:
* 31-24: 1 = Channel buffers empty (channel 7:0)
* 23-16: 1 = No pending requests (channel 7:0)
*/
#define IWL_FH_TSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xEA0)
#define IWL_FH_TSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xEC0)
#define IWL_FH_TSSR_TX_STATUS_REG (IWL_FH_TSSR_LOWER_BOUND + 0x010)
#define IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) \
((1 << (_chnl)) << 24)
#define IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl) \
((1 << (_chnl)) << 16)
#define IWL_FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) \
(IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) | \
IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl))
#define SCD_WIN_SIZE 64
#define SCD_FRAME_LIMIT 64
/* SRAM structures */
#define SCD_CONTEXT_DATA_OFFSET 0x380
#define SCD_TX_STTS_BITMAP_OFFSET 0x400
#define SCD_TRANSLATE_TBL_OFFSET 0x500
#define SCD_CONTEXT_QUEUE_OFFSET(x) (SCD_CONTEXT_DATA_OFFSET + ((x) * 8))
#define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)
#define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \
((1<<(hi))|((1<<(hi))-(1<<(lo))))
#define SCD_QUEUE_STTS_REG_POS_ACTIVE (0)
#define SCD_QUEUE_STTS_REG_POS_TXF (1)
#define SCD_QUEUE_STTS_REG_POS_WSL (5)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACK (8)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (10)
#define SCD_QUEUE_STTS_REG_MSK (0x0007FC00)
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_POS (0)
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK (0x0000007F)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS (16)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK (0x007F0000)
#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010)
#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
static inline u8 iwl4965_hw_get_rate(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFF;
}
static inline u16 iwl4965_hw_get_rate_n_flags(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFFFF;
}
static inline __le32 iwl4965_hw_set_rate_n_flags(u8 rate, u16 flags)
{
return cpu_to_le32(flags|(u16)rate);
}
struct iwl4965_tfd_frame_data {
__le32 tb1_addr;
__le32 val1;
/* __le32 ptb1_32_35:4; */
#define IWL_tb1_addr_hi_POS 0
#define IWL_tb1_addr_hi_LEN 4
#define IWL_tb1_addr_hi_SYM val1
/* __le32 tb_len1:12; */
#define IWL_tb1_len_POS 4
#define IWL_tb1_len_LEN 12
#define IWL_tb1_len_SYM val1
/* __le32 ptb2_0_15:16; */
#define IWL_tb2_addr_lo16_POS 16
#define IWL_tb2_addr_lo16_LEN 16
#define IWL_tb2_addr_lo16_SYM val1
__le32 val2;
/* __le32 ptb2_16_35:20; */
#define IWL_tb2_addr_hi20_POS 0
#define IWL_tb2_addr_hi20_LEN 20
#define IWL_tb2_addr_hi20_SYM val2
/* __le32 tb_len2:12; */
#define IWL_tb2_len_POS 20
#define IWL_tb2_len_LEN 12
#define IWL_tb2_len_SYM val2
} __attribute__ ((packed));
struct iwl4965_tfd_frame {
__le32 val0;
/* __le32 rsvd1:24; */
/* __le32 num_tbs:5; */
#define IWL_num_tbs_POS 24
#define IWL_num_tbs_LEN 5
#define IWL_num_tbs_SYM val0
/* __le32 rsvd2:1; */
/* __le32 padding:2; */
struct iwl4965_tfd_frame_data pa[10];
__le32 reserved;
} __attribute__ ((packed));
#define IWL4965_MAX_WIN_SIZE 64
#define IWL4965_QUEUE_SIZE 256
#define IWL4965_NUM_FIFOS 7
#define IWL_MAX_NUM_QUEUES 16
struct iwl4965_queue_byte_cnt_entry {
__le16 val;
/* __le16 byte_cnt:12; */
#define IWL_byte_cnt_POS 0
#define IWL_byte_cnt_LEN 12
#define IWL_byte_cnt_SYM val
/* __le16 rsvd:4; */
} __attribute__ ((packed));
struct iwl4965_sched_queue_byte_cnt_tbl {
struct iwl4965_queue_byte_cnt_entry tfd_offset[IWL4965_QUEUE_SIZE +
IWL4965_MAX_WIN_SIZE];
u8 dont_care[1024 -
(IWL4965_QUEUE_SIZE + IWL4965_MAX_WIN_SIZE) *
sizeof(__le16)];
} __attribute__ ((packed));
/* Base physical address of iwl4965_shared is provided to KDR_SCD_DRAM_BASE_ADDR
* and &iwl4965_shared.val0 is provided to FH_RSCSR_CHNL0_STTS_WPTR_REG */
struct iwl4965_shared {
struct iwl4965_sched_queue_byte_cnt_tbl
queues_byte_cnt_tbls[IWL_MAX_NUM_QUEUES];
__le32 val0;
/* __le32 rb_closed_stts_rb_num:12; */
#define IWL_rb_closed_stts_rb_num_POS 0
#define IWL_rb_closed_stts_rb_num_LEN 12
#define IWL_rb_closed_stts_rb_num_SYM val0
/* __le32 rsrv1:4; */
/* __le32 rb_closed_stts_rx_frame_num:12; */
#define IWL_rb_closed_stts_rx_frame_num_POS 16
#define IWL_rb_closed_stts_rx_frame_num_LEN 12
#define IWL_rb_closed_stts_rx_frame_num_SYM val0
/* __le32 rsrv2:4; */
__le32 val1;
/* __le32 frame_finished_stts_rb_num:12; */
#define IWL_frame_finished_stts_rb_num_POS 0
#define IWL_frame_finished_stts_rb_num_LEN 12
#define IWL_frame_finished_stts_rb_num_SYM val1
/* __le32 rsrv3:4; */
/* __le32 frame_finished_stts_rx_frame_num:12; */
#define IWL_frame_finished_stts_rx_frame_num_POS 16
#define IWL_frame_finished_stts_rx_frame_num_LEN 12
#define IWL_frame_finished_stts_rx_frame_num_SYM val1
/* __le32 rsrv4:4; */
__le32 padding1; /* so that allocation will be aligned to 16B */
__le32 padding2;
} __attribute__ ((packed));
#endif /* __iwl4965_4965_hw_h__ */
Reference in a new issue View git blame Copy permalink