kernel-fxtec-pro1x/drivers/net/wireless/libertas/README
Marcelo Tosatti 876c9d3aeb [PATCH] Marvell Libertas 8388 802.11b/g USB driver
Add the Marvell Libertas 8388 802.11 USB driver.

Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-04-28 11:00:54 -04:00

1044 lines
30 KiB
Text

================================================================================
README for USB8388
(c) Copyright © 2003-2006, Marvell International Ltd.
All Rights Reserved
This software file (the "File") is distributed by Marvell International
Ltd. under the terms of the GNU General Public License Version 2, June 1991
(the "License"). You may use, redistribute and/or modify this File in
accordance with the terms and conditions of the License, a copy of which
is available along with the File in the license.txt file or by writing to
the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
02111-1307 or on the worldwide web at http://www.gnu.org/licenses/gpl.txt.
THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
ARE EXPRESSLY DISCLAIMED. The License provides additional details about
this warranty disclaimer.
================================================================================
=====================
DRIVER LOADING
=====================
o. Copy the firmware image (e.g. usb8388.bin) to /lib/firmware/
o. Load driver by using the following command:
insmod usb8388.ko [fw_name=usb8388.bin]
=====================
IWPRIV COMMAND
=====================
NAME
This manual describes the usage of private commands used in Marvell WLAN
Linux Driver. All the commands available in Wlanconfig will not be available
in the iwpriv.
SYNOPSIS
iwpriv <ethX> <command> [sub-command] ...
iwpriv ethX version
iwpriv ethX scantype [sub-command]
iwpriv ethX getSNR <n>
iwpriv ethX getNF <n>
iwpriv ethX getRSSI <n>
iwpriv ethX setrxant <n>
iwpriv ethX getrxant
iwpriv ethX settxant <n>
iwpriv ethX gettxant
iwpriv ethX authalgs <n>
iwpriv ethX pre-TBTT <n>
iwpriv ethX 8021xauthalgs <n>
iwpriv ethX encryptionmode <n>
iwpriv ethX setregioncode <n>
iwpriv ethX getregioncode
iwpriv ethX setbcnavg <n>
iwpriv ethX getbcnavg
iwpriv ethX setdataavg <n>
iwpriv ethX setlisteninter <n>
iwpriv ethX getlisteninter
iwpriv ethX setmultipledtim <n>
iwpriv ethX getmultipledtim
iwpriv ethX atimwindow <n>
iwpriv ethX deauth
iwpriv ethX adhocstop
iwpriv ethX radioon
iwpriv ethX radiooff
iwpriv ethX reasso-on
iwpriv ethX reasso-off
iwpriv ethX scanmode [sub-command]
iwpriv ethX setwpaie <n>
iwpriv ethX wlanidle-off
iwpriv ethX wlanidle-on
iwpriv ethX getcis
iwpriv ethX getlog
iwpriv ethX getadhocstatus
iwpriv ethX adhocgrate <n>
Version 4 Command:
iwpriv ethX inactvityto <n>
iwpriv ethX sleeppd <n>
iwpriv ethX enable11d <n>
iwpriv ethX tpccfg <n>
iwpriv ethX powercfg <n>
iwpriv ethX setafc <n>
iwpriv ethX getafc
Version 5 Command:
iwpriv ethX ledgpio <n>
iwpriv ethX scanprobes <n>
iwpriv ethX lolisteninter <n>
iwpriv ethX rateadapt <n> <m>
iwpriv ethX txcontrol <n>
iwpriv ethX psnullinterval <n>
iwpriv ethX prescan <n>
iwpriv ethX getrxinfo
iwpriv ethX gettxrate
iwpriv ethX beaconinterval
BT Commands:
The blinding table (BT) contains a list of mac addresses that should be
ignored by the firmware. It is primarily used for debugging and
testing networks. It can be edited and inspected with the following
commands:
iwpriv ethX bt_reset
iwpriv ethX bt_add <mac_address>
iwpriv ethX bt_del <mac_address>
iwpriv ethX bt_list <id>
FWT Commands:
The forwarding table (FWT) is a feature used to manage mesh network
routing in the firmware. The FWT is essentially a routing table that
associates a destination mac address (da) with a next hop receiver
address (ra). The FWT can be inspected and edited with the following
iwpriv commands, which are described in greater detail below.
Eventually, the table will be automatically maintained by a custom
routing protocol.
NOTE: FWT commands replace the previous DFT commands. What were the DFT
commands?, you might ask. They were an earlier API to the firmware that
implemented a simple MAC-layer forwarding mechanism. In the unlikely
event that you were using these commands, you must migrate to the new
FWT commands which can be used to achieve the same functionality.
iwpriv ethX fwt_add [parameters]
iwpriv ethX fwt_del [parameters]
iwpriv ethX fwt_lookup [parameters]
iwpriv ethX fwt_list [parameters]
iwpriv ethX fwt_list_route [parameters]
iwpriv ethX fwt_list_neigh [parameters]
iwpriv ethX fwt_reset [parameters]
iwpriv ethX fwt_cleanup
iwpriv ethX fwt_time
MESH Commands:
The MESH commands are used to configure various features of the mesh
routing protocol. The following commands are supported:
iwpriv ethX mesh_get_ttl
iwpriv ethX mesh_set_ttl ttl
DESCRIPTION
Those commands are used to send additional commands to the Marvell WLAN
card via the Linux device driver.
The ethX parameter specifies the network device that is to be used to
perform this command on. it could be eth0, eth1 etc.
version
This is used to get the current version of the driver and the firmware.
scantype
This command is used to set the scan type to be used by the driver in
the scan command. This setting will not be used while performing a scan
for a specific SSID, as it is always done with scan type being active.
where the sub-commands are: -
active -- to set the scan type to active
passive -- to set the scan type to passive
get -- to get the scan type set in the driver
getSNR
This command gets the average and non average value of Signal to Noise
Ratio of Beacon and Data.
where value is:-
0 -- Beacon non-average.
1 -- Beacon average.
2 -- Data non-average.
3 -- Data average.
If no value is given, all four values are returned in the order mentioned
above.
Note: This command is available only when STA is connected.
getRSSI
This command gets the average and non average value os Receive Signal
Strength of Beacon and Data.
where value is:-
0 -- Beacon non-average.
1 -- Beacon average.
2 -- Data non-average.
3 -- Data average.
Note: This command is available only when STA is connected.
getNF
This command gets the average and non average value of Noise Floor of
Beacon and Data.
where value is:-
0 -- Beacon non-average.
1 -- Beacon average.
2 -- Data non-average.
3 -- Data average.
Note: This command is available only when STA is connected.
setrxant
This command is used to set the mode for Rx antenna.
The options that can be sent are:-
1 -- Antenna 1.
2 -- Antenna 2.
0xFFFF -- Diversity.
Usage:
iwpriv ethX setrxant 0x01: select Antenna 1.
getrxant
This command is used to get the mode for Rx antenna.
settxant
This command is used to set the mode for Tx antenna.
The options that can be sent are:-
1 -- Antenna 1.
2 -- Antenna 2.
0xFFFF -- Diversity.
Usage:
iwpriv ethX settxant 0x01: select Antenna 1.
gettxant
This command is used to get the mode for Tx antenna.
authalgs
This command is used by the WPA supplicant to set the authentication
algorithms in the station.
8021xauthalgs
This command is used by the WPA supplicant to set the 8021.x authentication algorithm type
station.
where values can be:-
1 -- None
2 -- LEAP
4 -- TLS
8 -- TTLs
16 -- MD5
encryptionmode
This command is used by the WPA supplicant to set the encryption algorithm.
where values can be:-
0 -- NONE
1 -- WEP40
2 -- TKIP
3 -- CCMP
4 -- WEP104
pre-TBTT
This command is used to set pre-TBTT time period where value is in microseconds.
setregioncode
This command is used to set the region code in the station.
where value is 'region code' for various regions like
USA FCC, Canada IC, Spain, France, Europe ETSI, Japan ...
Usage:
iwpriv ethX setregioncode 0x10: set region code to USA (0x10).
getregioncode
This command is used to get the region code information set in the
station.
setbcnavg
Set the weighting factor for calculating RSSI.
getbcnavg
Get weighting factor for calculating RSSI.
setdataavg
Set the weighting factor for calculating SNR.
setlisteninter
This command is used to set the listen interval in the
station.
where the value ranges between 1 - 255
getlisteninter
This command is used to get the listen interval value set in the
station.
setmultipledtim
This command is used to set the multiple dtim value in the
station.
where the value is 1,2,3,4,5,0xfffe
0xfffe means the firmware will use listen interval in association
command for waking up
getmultipledtim
This command is used to get the multiple dtim value set in the station.
atimwindow
This command is used to set the atim value in the
station.
where the value ranges between 0 - 50
deauth
This command is used to send the de-authentication to the AP with which
the station is associated. This command is valid only when
station is in Infrastructure mode.
Note: This command is available only when STA is connected.
adhocstop
This command is used to stop beacon transmission from the station and
go into idle state in ad-hoc mode.
Note: This command is available only when STA is connected.
radioon
This command is used to turn on the RF antenna.
radiooff
This command is sued to turn off the RF antenna.
scanmode
This command is used to set the station to scan for either IBSS
networks or BSS networks or both BSS and IBSS networks. This
command can be used with sub commands,
where the value for
bss -- Scan All the BSS networks.
ibss -- Scan All the IBSS networks.
any -- Scan both BSS and IBSS networks.
setwpaie
This command is used by WPA supplicant to send the WPA-IE to the driver.
wlanidle-off
This command is used to get into idle state.
Note: This command is available only when STA is connected.
wlanidle-on
This command is used to get off the idle state.
Note: This command is available only when STA is connected.
getlog
This command is used to get the 802.11 statistics available in the
station.
Note: This command is available only when STA is connected.
getadhocstatus
This command is used to get the ad-hoc Network Status.
The various status codes are:
AdhocStarted
AdhocJoined
AdhocIdle
InfraMode
AutoUnknownMode
Note: This command is available only when STA is connected.
adhocgrate
This command is used to enable(1) g_rate, Disable(0) g_rate
and request(2) the status which g_rate is disabled/enabled,
for Ad-hoc creator.
where value is:-
0 -- Disabled
1 -- Enabled
2 -- Get
ledgpio
This command is used to set/get LEDs.
iwpriv ethX ledgpio <LEDs>
will set the corresponding LED for the GPIO Line.
iwpriv ethX ledgpio
will give u which LEDs are Enabled.
Usage:
iwpriv eth1 ledgpio 1 0 2 1 3 4
will enable
LED 1 -> GPIO 0
LED 2 -> GPIO 1
LED 3 -> GPIO 4
iwpriv eth1 ledgpio
shows LED information in the format as mentioned above.
Note: LED0 is invalid
Note: Maximum Number of LEDs are 16.
inactivityto
This command is used by the host to set/get the inactivity timeout value,
which specifies when WLAN device is put to sleep.
Usage:
iwpriv ethX inactivityto [<timeout>]
where the parameter are:
timeout: timeout value in milliseconds.
Example:
iwpriv eth1 inactivityto
"get the timeout value"
iwpriv eth1 inactivityto X
"set timeout value to X ms"
sleeppd
This command is used to configure the sleep period of the WLAN device.
Usage:
iwpriv ethX sleeppd [<sleep period>]
where the parameter are:
Period: sleep period in milliseconds. Range 10~60.
Example:
iwpriv eth1 sleeppd 10
"set period as 10 ms"
iwpriv eth1 sleeppd
"get the sleep period configuration"
enable11d
This command is used to control 11d
where value is:-
1 -- Enabled
0 -- Disabled
2 -- Get
tpccfg
Enables or disables automatic transmit power control.
The first parameter turns this feature on (1) or off (0). When turning
on, the user must also supply four more parameters in the following
order:
-UseSNR (Use SNR (in addition to PER) for TPC algorithm),
-P0 (P0 power level for TPC),
-P1 (P1 power level for TPC),
-P2 (P2 power level for TPC).
Usage:
iwpriv ethX tpccfg: Get current configuration
iwpriv ethX tpccfg 0: disable auto TPC
iwpriv ethX tpccfg 0x01 0x00 0x05 0x0a 0x0d: enable auto TPC; do not use SNR;
P0=0x05; P1=0x0a; P2=0x0d;
iwpriv ethX tpccfg 0x01 0x01 0x05 0x0a 0x0d: enable auto TPC; use SNR;
P0=0x05; P1=0x0a; P2=0x0d.
powercfg
Enables or disables power adaptation.
The first parameter turns this feature on (1) or off (0). When turning
on, the user must also supply three more parameters in the following
order:
-P0 (P0 power level for Power Adaptation),
-P1 (P1 power level for Power Adaptation),
-P2 (P2 power level for Power Adaptation).
Usage:
iwpriv ethX powercfg: Get current configuration
iwpriv ethX powercfg 0: disable power adaptation
iwpriv ethX powercfg 1 0x0d 0x0f 0x12: enable power adaptation;
P0=0x0d; P1=0x0f; P2=0x12.
getafc
This command returns automatic frequency control parameters. It returns
three integers:
-P0: automatic is on (1), or off (0),
-P1: current timing offset in PPM (part per million), and
-P2: current frequency offset in PPM.
setafc
Set automatic frequency control options.
The first parameter turns automatic on (1) or off (0).
The user must supply two more parameters in either case, in the following
order:
When auto is on:
-P0 (automatic adjustment frequency threshold in PPM),
-P1 (automatic adjustment period in beacon period),
When auto is off:
-P0 (manual adjustment timing offset in PPM), and
-P1 (manual adjustment frequency offset in PPM).
Usage:
iwpriv ethX setafc 0 10 10: manual adjustment, both timing and frequcncy
offset are 10 PPM.
iwpriv ethX setafc 1 10 10 enable afc, automatic adjustment,
frequency threshold 10 PPM, for every 10 beacon periods.
scanprobes
This command sets number of probe requests per channel.
Usage:
iwpriv ethX scanprobes 3 (set scan probes to 3)
iwpriv ethX scanprobes (get scan probes)
lolisteninter
This command sets the value of listen interval.
Usage:
iwpriv ethX lolisteninter 234 (set the lolisteninter to 234)
iwpriv ethX lolisteninter (get the lolisteninter value)
rateadapt
This command sets the data rates bitmap.
Where <n>
0: Disable auto rate adapt
1: Enable auto rate adapt
<m>
data rate bitmap
Bit Data rate
0 1 Mbps
1 2 Mbps
2 5.5 Mbps
3 11 Mbps
4 Reserved
5 6 Mbps
6 9 Mbps
7 12 Mbps
8 18 Mbps
9 24 Mbps
10 36 Mbps
11 48 Mbps
12 54 Mbps
12-15 Reserved
Usage:
iwpriv ethX rateadapt
read the currect data rate setting
iwpriv ethX rateadapt 1 0x07
enable auto data rate adapt and
data rates are 1Mbps, 2Mbsp and 5.5Mbps
txcontrol
This command is used to set the Tx rate, ack policy, and retry limit on a per packet basis.
Where value <n> is:
if bit[4] == 1:
bit[3:0] -- 0 1 2 3 4 5 6 7 8 9 10 11 12 13-16
Data Rate(Mbps) -- 1 2 5.5 11 Rsv 6 9 12 18 24 36 48 54 Rsv
bit[12:8]
if bit[12] == 1, bit[11:8] specifies the Tx retry limit.
bit[14:13] specifies per packet ack policy:
bit[14:13]
1 0 use immediate ack policy for this packet
1 1 use no ack policy for this packet
0 x use the per-packet ack policy setting
Usage:
iwpriv ethX txcontrol 0x7513
Use no-ack policy, 5 retires for Tx, 11Mbps rate
psnullinterval
This command is used to set/request NULL package interval for Power Save
under infrastructure mode.
where value is:-
-1 -- Disabled
n>0 -- Set interval as n (seconds)
prescan
This command is used to enable (1)/disable(0) auto prescan before assoicate to the ap
where value is:-
0 -- Disabled
1 -- Enabled
2 -- Get
getrxinfo
This command gets non average value of Signal to Noise Ratio of Data and rate index.
The following table shows RateIndex and Rate
RateIndex Data rate
0 1 Mbps
1 2 Mbps
2 5.5 Mbps
3 11 Mbps
4 Reserved
5 6 Mbps
6 9 Mbps
7 12 Mbps
8 18 Mbps
9 24 Mbps
10 36 Mbps
11 48 Mbps
12 54 Mbps
13-15 Reserved
gettxrate
This command gets current Tx rate index of the first packet associated with Rate Adaptation.
The following table shows RateIndex and Rate
RateIndex Data rate
0 1 Mbps
1 2 Mbps
2 5.5 Mbps
3 11 Mbps
4 Reserved
5 6 Mbps
6 9 Mbps
7 12 Mbps
8 18 Mbps
9 24 Mbps
10 36 Mbps
11 48 Mbps
12 54 Mbps
13-15 Reserved
bcninterval
This command is used to sets beacon interval in adhoc mode when an argument is given, and gets current adhoc
beacon interval when no argument is given. The valid beacon interval is between 20 - 1000,
default beacon interval is 100.
Usage:
iwpriv ethX bcninterval 100 (set adhoc beacon interval to 100)
iwpriv ethX bcninterval (get adhoc beacon interval)
fwt_add
This command is used to insert an entry into the FWT table. The list of
parameters must follow the following structure:
iwpriv ethX fwt_add da ra [metric dir ssn dsn hopcount ttl expiration sleepmode snr]
The parameters between brackets are optional, but they must appear in
the order specified. For example, if you want to specify the metric,
you must also specify the dir, ssn, and dsn but you need not specify the
hopcount, expiration, sleepmode, or snr. Any unspecified parameters
will be assigned the defaults specified below.
The different parameters are:-
da -- DA MAC address in the form 00:11:22:33:44:55
ra -- RA MAC address in the form 00:11:22:33:44:55
metric -- route metric (cost: smaller-metric routes are
preferred, default is 0)
dir -- direction (1 for direct, 0 for reverse,
default is 1)
ssn -- Source Sequence Number (time at the RA for
reverse routes. Default is 0)
dsn -- Destination Sequence Number (time at the DA
for direct routes. Default is 0)
hopcount -- hop count (currently unused, default is 0)
ttl -- TTL (Only used in reverse entries)
expiration -- entry expiration (in ticks, where a tick is
1024us, or ~ 1ms. Use 0 for an indefinite
entry, default is 0)
sleepmode -- RA's sleep mode (currently unused, default is
0)
snr -- SNR in the link to RA (currently unused,
default is 0)
The command does not return anything.
fwt_del
This command is used to remove an entry to the FWT table. The list of
parameters must follow the following structure:
iwpriv ethX fwt_del da ra [dir]
where the different parameters are:-
da -- DA MAC address (in the form "00:11:22:33:44:55")
ra -- RA MAC address (in the form "00:11:22:33:44:55")
dir -- direction (1 for direct, 0 for reverse,
default is 1)
The command does not return anything.
fwt_lookup
This command is used to get the best route in the FWT table to a given
host. The only parameter is the MAC address of the host that is being
looked for.
iwpriv ethX fwt_lookup da
where:-
da -- DA MAC address (in the form "00:11:22:33:44:55")
The command returns an output string identical to the one returned by
fwt_list described below.
fwt_list
This command is used to list a route from the FWT table. The only
parameter is the index into the table. If you want to list all the
routes in a table, start with index=0, and keep listing until you get a
"(null)" string. Note that the indicies may change as the fwt is
updated. It is expected that most users will not use fwt_list directly,
but that a utility similar to the traditional route command will be used
to invoke fwt_list over and over.
iwpriv ethX fwt_list index
The output is a string of the following form:
da ra metric dir ssn dsn hopcount ttl expiration sleepmode snr
where the different fields are:-
da -- DA MAC address (in the form "00:11:22:33:44:55")
ra -- RA MAC address (in the form "00:11:22:33:44:55")
metric -- route metric (cost: smaller-metric routes are preferred)
dir -- direction (1 for direct, 0 for reverse)
ssn -- Source Sequence Number (time at the RA for reverse routes)
dsn -- Destination Sequence Number (time at the DA for direct routes)
hopcount -- hop count (currently unused)
ttl -- TTL (only used in reverse entries)
expiration -- entry expiration (in ticks, where a tick is 1024us, or ~ 1ms. Use 0 for an indefinite entry)
sleepmode -- RA's sleep mode (currently unused)
snr -- SNR in the link to RA (currently unused)
fwt_list_route
This command is used to list a route from the FWT table. The only
parameter is the route ID. If you want to list all the routes in a
table, start with rid=0, and keep incrementing rid until you get a
"(null)" string. This function is similar to fwt_list. The only
difference is the output format. Also note that this command is meant
for debugging. It is expected that users will use fwt_lookup and
fwt_list. One important reason for this is that the route id may change
as the route table is altered.
iwpriv ethX fwt_list_route rid
The output is a string of the following form:
da metric dir nid ssn dsn hopcount ttl expiration
where the different fields are:-
da -- DA MAC address (in the form "00:11:22:33:44:55")
metric -- route metric (cost: smaller-metric routes are preferred)
dir -- direction (1 for direct, 0 for reverse)
nid -- Next-hop (neighbor) host ID (nid)
ssn -- Source Sequence Number (time at the RA for reverse routes)
dsn -- Destination Sequence Number (time at the DA for direct routes)
hopcount -- hop count (currently unused)
ttl -- TTL count (only used in reverse entries)
expiration -- entry expiration (in ticks, where a tick is 1024us, or ~ 1ms. Use 0 for an indefinite entry)
fwt_list_neigh
This command is used to list a neighbor from the FWT table. The only
parameter is the neighbor ID. If you want to list all the neighbors in a
table, start with nid=0, and keep incrementing nid until you get a
"(null)" string. Note that the nid from a fwt_list_route command can be
used as an input to this command. Also note that this command is meant
mostly for debugging. It is expected that users will use fwt_lookup.
One important reason for this is that the neighbor id may change as the
neighbor table is altered.
iwpriv ethX fwt_list_neigh nid
The output is a string of the following form:
ra sleepmode snr references
where the different fields are:-
ra -- RA MAC address (in the form "00:11:22:33:44:55")
sleepmode -- RA's sleep mode (currently unused)
snr -- SNR in the link to RA (currently unused)
references -- RA's reference counter
fwt_reset
This command is used to reset the FWT table, getting rid of all the
entries. There are no input parameters.
iwpriv ethX fwt_reset
The command does not return anything.
fwt_cleanup
This command is used to perform user-based garbage recollection. The
FWT table is checked, and all the entries that are expired or invalid
are cleaned. Note that this is exported to the driver for debugging
purposes, as garbage collection is also fired by the firmware when in
space problems. There are no input parameters.
iwpriv ethX fwt_cleanup
The command does returns the number of invalid/expired routes deleted.
fwt_time
This command returns a card's internal time representation. It is this
time that is used to represent the expiration times of FWT entries. The
number is not consistent from card to card; it is simply a timer count.
The fwt_time command is used to inspect the timer so that expiration
times reported by fwt_list can be properly interpreted.
iwpriv ethX fwt_time
mesh_get_ttl
The mesh ttl is the number of hops a mesh packet can traverse before it
is dropped. This parameter is used to prevent infinite loops in the
mesh network. The value returned by this function is the ttl assigned
to all mesh packets. Currently there is no way to control the ttl on a
per packet or per socket basis.
iwpriv ethX mesh_get_ttl
mesh_set_ttl ttl
Set the ttl. The argument must be between 0 and 255.
iwpriv ethX mesh_set_ttl <ttl>
=========================
ETHTOOL
=========================
Use the -i option to retrieve version information from the driver.
# ethtool -i eth0
driver: libertas
version: COMM-USB8388-318.p4
firmware-version: 5.110.7
bus-info:
Use the -e option to read the EEPROM contents of the card.
Usage:
ethtool -e ethX [raw on|off] [offset N] [length N]
-e retrieves and prints an EEPROM dump for the specified ethernet
device. When raw is enabled, then it dumps the raw EEPROM data
to stdout. The length and offset parameters allow dumping cer-
tain portions of the EEPROM. Default is to dump the entire EEP-
ROM.
# ethtool -e eth0 offset 0 length 16
Offset Values
------ ------
0x0000 38 33 30 58 00 00 34 f4 00 00 10 00 00 c4 17 00
========================
DEBUGFS COMMANDS
========================
those commands are used via debugfs interface
===========
rdmac
rdbbp
rdrf
These commands are used to read the MAC, BBP and RF registers from the
card. These commands take one parameter that specifies the offset
location that is to be read. This parameter must be specified in
hexadecimal (its possible to preceed preceding the number with a "0x").
Path: /debugfs/libertas_wireless/ethX/registers/
Usage:
echo "0xa123" > rdmac ; cat rdmac
echo "0xa123" > rdbbp ; cat rdbbp
echo "0xa123" > rdrf ; cat rdrf
wrmac
wrbbp
wrrf
These commands are used to write the MAC, BBP and RF registers in the
card. These commands take two parameters that specify the offset
location and the value that is to be written. This parameters must
be specified in hexadecimal (its possible to preceed the number
with a "0x").
Usage:
echo "0xa123 0xaa" > wrmac
echo "0xa123 0xaa" > wrbbp
echo "0xa123 0xaa" > wrrf
sleepparams
This command is used to set the sleepclock configurations
Path: /debugfs/libertas_wireless/ethX/
Usage:
cat sleepparams: reads the current sleepclock configuration
echo "p1 p2 p3 p4 p5 p6" > sleepparams: writes the sleepclock configuration.
where:
p1 is Sleep clock error in ppm (0-65535)
p2 is Wakeup offset in usec (0-65535)
p3 is Clock stabilization time in usec (0-65535)
p4 is Control periodic calibration (0-2)
p5 is Control the use of external sleep clock (0-2)
p6 is reserved for debug (0-65535)
subscribed_events
The subscribed_events directory contains the interface for the
subscribed events API.
Path: /debugfs/libertas_wireless/ethX/subscribed_events/
Each event is represented by a filename. Each filename consists of the
following three fields:
Value Frequency Subscribed
To read the current values for a given event, do:
cat event
To set the current values, do:
echo "60 2 1" > event
Frequency field specifies the reporting frequency for this event.
If it is set to 0, then the event is reported only once, and then
automatically unsubscribed. If it is set to 1, then the event is
reported every time it occurs. If it is set to N, then the event is
reported every Nth time it occurs.
beacon_missed
Value field specifies the number of consecutive missing beacons which
triggers the LINK_LOSS event. This event is generated only once after
which the firmware resets its state. At initialization, the LINK_LOSS
event is subscribed by default. The default value of MissedBeacons is
60.
failure_count
Value field specifies the consecutive failure count threshold which
triggers the generation of the MAX_FAIL event. Once this event is
generated, the consecutive failure count is reset to 0.
At initialization, the MAX_FAIL event is NOT subscribed by
default.
high_rssi
This event is generated when the average received RSSI in beacons goes
above a threshold, specified by Value.
low_rssi
This event is generated when the average received RSSI in beacons goes
below a threshold, specified by Value.
high_snr
This event is generated when the average received SNR in beacons goes
above a threshold, specified by Value.
low_snr
This event is generated when the average received SNR in beacons goes
below a threshold, specified by Value.
extscan
This command is used to do a specific scan.
Path: /debugfs/libertas_wireless/ethX/
Usage: echo "SSID" > extscan
Example:
echo "LINKSYS-AP" > extscan
To see the results of use getscantable command.
getscantable
Display the current contents of the driver scan table (ie. get the
scan results).
Path: /debugfs/libertas_wireless/ethX/
Usage:
cat getscantable
setuserscan
Initiate a customized scan and retrieve the results
Path: /debugfs/libertas_wireless/ethX/
Usage:
echo "[ARGS]" > setuserscan
where [ARGS]:
chan=[chan#][band][mode] where band is [a,b,g] and mode is
blank for active or 'p' for passive
bssid=xx:xx:xx:xx:xx:xx specify a BSSID filter for the scan
ssid="[SSID]" specify a SSID filter for the scan
keep=[0 or 1] keep the previous scan results (1), discard (0)
dur=[scan time] time to scan for each channel in milliseconds
probes=[#] number of probe requests to send on each chan
type=[1,2,3] BSS type: 1 (Infra), 2(Adhoc), 3(Any)
Any combination of the above arguments can be supplied on the command line.
If the chan token is absent, a full channel scan will be completed by
the driver. If the dur or probes tokens are absent, the driver default
setting will be used. The bssid and ssid fields, if blank,
will produce an unfiltered scan. The type field will default to 3 (Any)
and the keep field will default to 0 (Discard).
Examples:
1) Perform an active scan on channels 1, 6, and 11 in the 'g' band:
echo "chan=1g,6g,11g" > setuserscan
2) Perform a passive scan on channel 11 for 20 ms:
echo "chan=11gp dur=20" > setuserscan
3) Perform an active scan on channels 1, 6, and 11; and a passive scan on
channel 36 in the 'a' band:
echo "chan=1g,6g,11g,36ap" > setuserscan
4) Perform an active scan on channel 6 and 36 for a specific SSID:
echo "chan=6g,36a ssid="TestAP"" > setuserscan
5) Scan all available channels (B/G, A bands) for a specific BSSID, keep
the current scan table intact, update existing or append new scan data:
echo "bssid=00:50:43:20:12:82 keep=1" > setuserscan
6) Scan channel 6, for all infrastructure networks, sending two probe
requests. Keep the previous scan table intact. Update any duplicate
BSSID/SSID matches with the new scan data:
echo "chan=6g type=1 probes=2 keep=1" > setuserscan
All entries in the scan table (not just the new scan data when keep=1)
will be displayed upon completion by use of the getscantable ioctl.
==============================================================================