116 lines
3.8 KiB
C
116 lines
3.8 KiB
C
/*
|
|
* Copyright 2002 MontaVista Software Inc.
|
|
* Author: MontaVista Software, Inc.
|
|
* ppopov@mvista.com or source@mvista.com
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
|
|
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
|
|
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
|
|
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* You should have received a copy of the GNU General Public License along
|
|
* with this program; if not, write to the Free Software Foundation, Inc.,
|
|
* 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
#include <linux/init.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/console.h>
|
|
#include <linux/delay.h>
|
|
|
|
#include <asm/cpu.h>
|
|
#include <asm/bootinfo.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/mipsregs.h>
|
|
#include <asm/reboot.h>
|
|
#include <asm/pgtable.h>
|
|
#include <asm/mach-au1x00/au1000.h>
|
|
#include <asm/mach-pb1x00/pb1100.h>
|
|
|
|
void board_reset(void)
|
|
{
|
|
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
|
|
au_writel(0x00000000, 0xAE00001C);
|
|
}
|
|
|
|
void __init board_setup(void)
|
|
{
|
|
volatile void __iomem * base = (volatile void __iomem *) 0xac000000UL;
|
|
|
|
// set AUX clock to 12MHz * 8 = 96 MHz
|
|
au_writel(8, SYS_AUXPLL);
|
|
au_writel(0, SYS_PININPUTEN);
|
|
udelay(100);
|
|
|
|
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
|
|
{
|
|
u32 pin_func, sys_freqctrl, sys_clksrc;
|
|
|
|
// configure pins GPIO[14:9] as GPIO
|
|
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80);
|
|
|
|
/* zero and disable FREQ2 */
|
|
sys_freqctrl = au_readl(SYS_FREQCTRL0);
|
|
sys_freqctrl &= ~0xFFF00000;
|
|
au_writel(sys_freqctrl, SYS_FREQCTRL0);
|
|
|
|
/* zero and disable USBH/USBD/IrDA clock */
|
|
sys_clksrc = au_readl(SYS_CLKSRC);
|
|
sys_clksrc &= ~0x0000001F;
|
|
au_writel(sys_clksrc, SYS_CLKSRC);
|
|
|
|
sys_freqctrl = au_readl(SYS_FREQCTRL0);
|
|
sys_freqctrl &= ~0xFFF00000;
|
|
|
|
sys_clksrc = au_readl(SYS_CLKSRC);
|
|
sys_clksrc &= ~0x0000001F;
|
|
|
|
// FREQ2 = aux/2 = 48 MHz
|
|
sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
|
|
au_writel(sys_freqctrl, SYS_FREQCTRL0);
|
|
|
|
/*
|
|
* Route 48MHz FREQ2 into USBH/USBD/IrDA
|
|
*/
|
|
sys_clksrc |= ((4<<2) | (0<<1) | 0 );
|
|
au_writel(sys_clksrc, SYS_CLKSRC);
|
|
|
|
/* setup the static bus controller */
|
|
au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
|
|
au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
|
|
au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
|
|
|
|
// get USB Functionality pin state (device vs host drive pins)
|
|
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
|
|
// 2nd USB port is USB host
|
|
pin_func |= 0x8000;
|
|
au_writel(pin_func, SYS_PINFUNC);
|
|
}
|
|
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
|
|
|
|
/* Enable sys bus clock divider when IDLE state or no bus activity. */
|
|
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
|
|
|
|
// Enable the RTC if not already enabled
|
|
if (!(readb(base + 0x28) & 0x20)) {
|
|
writeb(readb(base + 0x28) | 0x20, base + 0x28);
|
|
au_sync();
|
|
}
|
|
// Put the clock in BCD mode
|
|
if (readb(base + 0x2C) & 0x4) { /* reg B */
|
|
writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
|
|
au_sync();
|
|
}
|
|
}
|