kernel-fxtec-pro1x/arch/arm/mach-s3c6410/mach-smdk6410.c
Mark Brown a3323b72b9 ARM: SMDK6410: Configure GPIO pull up for WM835x IRQ line
When used with the WM1190-EV1 board we can use the internal pull up
resistor of the CPU to provide the required pull for the IRQ line.
Without this interrupts from the WM835x don't work in the default
WM1190-EV1 hardwaer configuration.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-11-09 23:40:21 +00:00

404 lines
9.3 KiB
C

/* linux/arch/arm/mach-s3c6410/mach-smdk6410.c
*
* Copyright 2008 Openmoko, Inc.
* Copyright 2008 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
* http://armlinux.simtec.co.uk/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/fb.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/smsc911x.h>
#ifdef CONFIG_SMDK6410_WM1190_EV1
#include <linux/mfd/wm8350/core.h>
#include <linux/mfd/wm8350/pmic.h>
#endif
#include <video/platform_lcd.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/hardware.h>
#include <mach/regs-fb.h>
#include <mach/map.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
#include <plat/regs-modem.h>
#include <plat/regs-gpio.h>
#include <plat/regs-sys.h>
#include <plat/iic.h>
#include <plat/fb.h>
#include <plat/gpio-cfg.h>
#include <plat/s3c6410.h>
#include <plat/clock.h>
#include <plat/devs.h>
#include <plat/cpu.h>
#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
static struct s3c2410_uartcfg smdk6410_uartcfgs[] __initdata = {
[0] = {
.hwport = 0,
.flags = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
},
[1] = {
.hwport = 1,
.flags = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
},
[2] = {
.hwport = 2,
.flags = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
},
[3] = {
.hwport = 3,
.flags = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
},
};
/* framebuffer and LCD setup. */
/* GPF15 = LCD backlight control
* GPF13 => Panel power
* GPN5 = LCD nRESET signal
* PWM_TOUT1 => backlight brightness
*/
static void smdk6410_lcd_power_set(struct plat_lcd_data *pd,
unsigned int power)
{
if (power) {
gpio_direction_output(S3C64XX_GPF(13), 1);
gpio_direction_output(S3C64XX_GPF(15), 1);
/* fire nRESET on power up */
gpio_direction_output(S3C64XX_GPN(5), 0);
msleep(10);
gpio_direction_output(S3C64XX_GPN(5), 1);
msleep(1);
} else {
gpio_direction_output(S3C64XX_GPF(15), 0);
gpio_direction_output(S3C64XX_GPF(13), 0);
}
}
static struct plat_lcd_data smdk6410_lcd_power_data = {
.set_power = smdk6410_lcd_power_set,
};
static struct platform_device smdk6410_lcd_powerdev = {
.name = "platform-lcd",
.dev.parent = &s3c_device_fb.dev,
.dev.platform_data = &smdk6410_lcd_power_data,
};
static struct s3c_fb_pd_win smdk6410_fb_win0 = {
/* this is to ensure we use win0 */
.win_mode = {
.pixclock = 41094,
.left_margin = 8,
.right_margin = 13,
.upper_margin = 7,
.lower_margin = 5,
.hsync_len = 3,
.vsync_len = 1,
.xres = 800,
.yres = 480,
},
.max_bpp = 32,
.default_bpp = 16,
};
/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */
static struct s3c_fb_platdata smdk6410_lcd_pdata __initdata = {
.setup_gpio = s3c64xx_fb_gpio_setup_24bpp,
.win[0] = &smdk6410_fb_win0,
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
};
static struct resource smdk6410_smsc911x_resources[] = {
[0] = {
.start = 0x18000000,
.end = 0x18000000 + SZ_64K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = S3C_EINT(10),
.end = S3C_EINT(10),
.flags = IORESOURCE_IRQ | IRQ_TYPE_LEVEL_LOW,
},
};
static struct smsc911x_platform_config smdk6410_smsc911x_pdata = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct platform_device smdk6410_smsc911x = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(smdk6410_smsc911x_resources),
.resource = &smdk6410_smsc911x_resources[0],
.dev = {
.platform_data = &smdk6410_smsc911x_pdata,
},
};
static struct map_desc smdk6410_iodesc[] = {};
static struct platform_device *smdk6410_devices[] __initdata = {
#ifdef CONFIG_SMDK6410_SD_CH0
&s3c_device_hsmmc0,
#endif
#ifdef CONFIG_SMDK6410_SD_CH1
&s3c_device_hsmmc1,
#endif
&s3c_device_i2c0,
&s3c_device_i2c1,
&s3c_device_fb,
&s3c_device_usb,
&s3c_device_usb_hsotg,
&smdk6410_lcd_powerdev,
&smdk6410_smsc911x,
};
#ifdef CONFIG_SMDK6410_WM1190_EV1
/* S3C64xx internal logic & PLL */
static struct regulator_init_data wm8350_dcdc1_data = {
.constraints = {
.name = "PVDD_INT/PVDD_PLL",
.min_uV = 1200000,
.max_uV = 1200000,
.always_on = 1,
.apply_uV = 1,
},
};
/* Memory */
static struct regulator_init_data wm8350_dcdc3_data = {
.constraints = {
.name = "PVDD_MEM",
.min_uV = 1800000,
.max_uV = 1800000,
.always_on = 1,
.state_mem = {
.uV = 1800000,
.mode = REGULATOR_MODE_NORMAL,
.enabled = 1,
},
.initial_state = PM_SUSPEND_MEM,
},
};
/* USB, EXT, PCM, ADC/DAC, USB, MMC */
static struct regulator_init_data wm8350_dcdc4_data = {
.constraints = {
.name = "PVDD_HI/PVDD_EXT/PVDD_SYS/PVCCM2MTV",
.min_uV = 3000000,
.max_uV = 3000000,
.always_on = 1,
},
};
/* ARM core */
static struct regulator_consumer_supply dcdc6_consumers[] = {
{
.supply = "vddarm",
}
};
static struct regulator_init_data wm8350_dcdc6_data = {
.constraints = {
.name = "PVDD_ARM",
.min_uV = 1000000,
.max_uV = 1300000,
.always_on = 1,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
},
.num_consumer_supplies = ARRAY_SIZE(dcdc6_consumers),
.consumer_supplies = dcdc6_consumers,
};
/* Alive */
static struct regulator_init_data wm8350_ldo1_data = {
.constraints = {
.name = "PVDD_ALIVE",
.min_uV = 1200000,
.max_uV = 1200000,
.always_on = 1,
.apply_uV = 1,
},
};
/* OTG */
static struct regulator_init_data wm8350_ldo2_data = {
.constraints = {
.name = "PVDD_OTG",
.min_uV = 3300000,
.max_uV = 3300000,
.always_on = 1,
},
};
/* LCD */
static struct regulator_init_data wm8350_ldo3_data = {
.constraints = {
.name = "PVDD_LCD",
.min_uV = 3000000,
.max_uV = 3000000,
.always_on = 1,
},
};
/* OTGi/1190-EV1 HPVDD & AVDD */
static struct regulator_init_data wm8350_ldo4_data = {
.constraints = {
.name = "PVDD_OTGI/HPVDD/AVDD",
.min_uV = 1200000,
.max_uV = 1200000,
.apply_uV = 1,
.always_on = 1,
},
};
static struct {
int regulator;
struct regulator_init_data *initdata;
} wm1190_regulators[] = {
{ WM8350_DCDC_1, &wm8350_dcdc1_data },
{ WM8350_DCDC_3, &wm8350_dcdc3_data },
{ WM8350_DCDC_4, &wm8350_dcdc4_data },
{ WM8350_DCDC_6, &wm8350_dcdc6_data },
{ WM8350_LDO_1, &wm8350_ldo1_data },
{ WM8350_LDO_2, &wm8350_ldo2_data },
{ WM8350_LDO_3, &wm8350_ldo3_data },
{ WM8350_LDO_4, &wm8350_ldo4_data },
};
static int __init smdk6410_wm8350_init(struct wm8350 *wm8350)
{
int i;
/* Configure the IRQ line */
s3c_gpio_setpull(S3C64XX_GPN(12), S3C_GPIO_PULL_UP);
/* Instantiate the regulators */
for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++)
wm8350_register_regulator(wm8350,
wm1190_regulators[i].regulator,
wm1190_regulators[i].initdata);
return 0;
}
static struct wm8350_platform_data __initdata smdk6410_wm8350_pdata = {
.init = smdk6410_wm8350_init,
.irq_high = 1,
};
#endif
static struct i2c_board_info i2c_devs0[] __initdata = {
{ I2C_BOARD_INFO("24c08", 0x50), },
{ I2C_BOARD_INFO("wm8580", 0x1b), },
#ifdef CONFIG_SMDK6410_WM1190_EV1
{ I2C_BOARD_INFO("wm8350", 0x1a),
.platform_data = &smdk6410_wm8350_pdata,
.irq = S3C_EINT(12),
},
#endif
};
static struct i2c_board_info i2c_devs1[] __initdata = {
{ I2C_BOARD_INFO("24c128", 0x57), }, /* Samsung S524AD0XD1 */
};
static void __init smdk6410_map_io(void)
{
u32 tmp;
s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
s3c24xx_init_clocks(12000000);
s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
/* set the LCD type */
tmp = __raw_readl(S3C64XX_SPCON);
tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK;
tmp |= S3C64XX_SPCON_LCD_SEL_RGB;
__raw_writel(tmp, S3C64XX_SPCON);
/* remove the lcd bypass */
tmp = __raw_readl(S3C64XX_MODEM_MIFPCON);
tmp &= ~MIFPCON_LCD_BYPASS;
__raw_writel(tmp, S3C64XX_MODEM_MIFPCON);
}
static void __init smdk6410_machine_init(void)
{
s3c_i2c0_set_platdata(NULL);
s3c_i2c1_set_platdata(NULL);
s3c_fb_set_platdata(&smdk6410_lcd_pdata);
gpio_request(S3C64XX_GPN(5), "LCD power");
gpio_request(S3C64XX_GPF(13), "LCD power");
gpio_request(S3C64XX_GPF(15), "LCD power");
i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
platform_add_devices(smdk6410_devices, ARRAY_SIZE(smdk6410_devices));
}
MACHINE_START(SMDK6410, "SMDK6410")
/* Maintainer: Ben Dooks <ben@fluff.org> */
.phys_io = S3C_PA_UART & 0xfff00000,
.io_pg_offst = (((u32)S3C_VA_UART) >> 18) & 0xfffc,
.boot_params = S3C64XX_PA_SDRAM + 0x100,
.init_irq = s3c6410_init_irq,
.map_io = smdk6410_map_io,
.init_machine = smdk6410_machine_init,
.timer = &s3c24xx_timer,
MACHINE_END