3c42a44910
Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
150 lines
4.8 KiB
C
150 lines
4.8 KiB
C
/*
|
|
* linux/include/asm-arm/arch-pxa/pxafb.h
|
|
*
|
|
* Support for the xscale frame buffer.
|
|
*
|
|
* Author: Jean-Frederic Clere
|
|
* Created: Sep 22, 2003
|
|
* Copyright: jfclere@sinix.net
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/fb.h>
|
|
#include <asm/arch/regs-lcd.h>
|
|
|
|
/*
|
|
* Supported LCD connections
|
|
*
|
|
* bits 0 - 3: for LCD panel type:
|
|
*
|
|
* STN - for passive matrix
|
|
* DSTN - for dual scan passive matrix
|
|
* TFT - for active matrix
|
|
*
|
|
* bits 4 - 9 : for bus width
|
|
* bits 10-17 : for AC Bias Pin Frequency
|
|
* bit 18 : for output enable polarity
|
|
* bit 19 : for pixel clock edge
|
|
*/
|
|
#define LCD_CONN_TYPE(_x) ((_x) & 0x0f)
|
|
#define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f)
|
|
|
|
#define LCD_TYPE_UNKNOWN 0
|
|
#define LCD_TYPE_MONO_STN 1
|
|
#define LCD_TYPE_MONO_DSTN 2
|
|
#define LCD_TYPE_COLOR_STN 3
|
|
#define LCD_TYPE_COLOR_DSTN 4
|
|
#define LCD_TYPE_COLOR_TFT 5
|
|
#define LCD_TYPE_SMART_PANEL 6
|
|
#define LCD_TYPE_MAX 7
|
|
|
|
#define LCD_MONO_STN_4BPP ((4 << 4) | LCD_TYPE_MONO_STN)
|
|
#define LCD_MONO_STN_8BPP ((8 << 4) | LCD_TYPE_MONO_STN)
|
|
#define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN)
|
|
#define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN)
|
|
#define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN)
|
|
#define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT)
|
|
#define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT)
|
|
#define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL)
|
|
#define LCD_SMART_PANEL_16BPP ((16 << 4) | LCD_TYPE_SMART_PANEL)
|
|
#define LCD_SMART_PANEL_18BPP ((18 << 4) | LCD_TYPE_SMART_PANEL)
|
|
|
|
#define LCD_AC_BIAS_FREQ(x) (((x) & 0xff) << 10)
|
|
#define LCD_BIAS_ACTIVE_HIGH (0 << 17)
|
|
#define LCD_BIAS_ACTIVE_LOW (1 << 17)
|
|
#define LCD_PCLK_EDGE_RISE (0 << 18)
|
|
#define LCD_PCLK_EDGE_FALL (1 << 18)
|
|
|
|
/*
|
|
* This structure describes the machine which we are running on.
|
|
* It is set in linux/arch/arm/mach-pxa/machine_name.c and used in the probe routine
|
|
* of linux/drivers/video/pxafb.c
|
|
*/
|
|
struct pxafb_mode_info {
|
|
u_long pixclock;
|
|
|
|
u_short xres;
|
|
u_short yres;
|
|
|
|
u_char bpp;
|
|
u_int cmap_greyscale:1,
|
|
unused:31;
|
|
|
|
/* Parallel Mode Timing */
|
|
u_char hsync_len;
|
|
u_char left_margin;
|
|
u_char right_margin;
|
|
|
|
u_char vsync_len;
|
|
u_char upper_margin;
|
|
u_char lower_margin;
|
|
u_char sync;
|
|
|
|
/* Smart Panel Mode Timing - see PXA27x DM 7.4.15.0.3 for details
|
|
* Note:
|
|
* 1. all parameters in nanosecond (ns)
|
|
* 2. a0cs{rd,wr}_set_hld are controlled by the same register bits
|
|
* in pxa27x and pxa3xx, initialize them to the same value or
|
|
* the larger one will be used
|
|
* 3. same to {rd,wr}_pulse_width
|
|
*/
|
|
unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */
|
|
unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */
|
|
unsigned wr_pulse_width; /* L_PCLK_WR pulse width */
|
|
unsigned rd_pulse_width; /* L_FCLK_RD pulse width */
|
|
unsigned cmd_inh_time; /* Command Inhibit time between two writes */
|
|
unsigned op_hold_time; /* Output Hold time from L_FCLK_RD negation */
|
|
};
|
|
|
|
struct pxafb_mach_info {
|
|
struct pxafb_mode_info *modes;
|
|
unsigned int num_modes;
|
|
|
|
unsigned int lcd_conn;
|
|
|
|
u_int fixed_modes:1,
|
|
cmap_inverse:1,
|
|
cmap_static:1,
|
|
unused:29;
|
|
|
|
/* The following should be defined in LCCR0
|
|
* LCCR0_Act or LCCR0_Pas Active or Passive
|
|
* LCCR0_Sngl or LCCR0_Dual Single/Dual panel
|
|
* LCCR0_Mono or LCCR0_Color Mono/Color
|
|
* LCCR0_4PixMono or LCCR0_8PixMono (in mono single mode)
|
|
* LCCR0_DMADel(Tcpu) (optional) DMA request delay
|
|
*
|
|
* The following should not be defined in LCCR0:
|
|
* LCCR0_OUM, LCCR0_BM, LCCR0_QDM, LCCR0_DIS, LCCR0_EFM
|
|
* LCCR0_IUM, LCCR0_SFM, LCCR0_LDM, LCCR0_ENB
|
|
*/
|
|
u_int lccr0;
|
|
/* The following should be defined in LCCR3
|
|
* LCCR3_OutEnH or LCCR3_OutEnL Output enable polarity
|
|
* LCCR3_PixRsEdg or LCCR3_PixFlEdg Pixel clock edge type
|
|
* LCCR3_Acb(X) AB Bias pin frequency
|
|
* LCCR3_DPC (optional) Double Pixel Clock mode (untested)
|
|
*
|
|
* The following should not be defined in LCCR3
|
|
* LCCR3_HSP, LCCR3_VSP, LCCR0_Pcd(x), LCCR3_Bpp
|
|
*/
|
|
u_int lccr3;
|
|
/* The following should be defined in LCCR4
|
|
* LCCR4_PAL_FOR_0 or LCCR4_PAL_FOR_1 or LCCR4_PAL_FOR_2
|
|
*
|
|
* All other bits in LCCR4 should be left alone.
|
|
*/
|
|
u_int lccr4;
|
|
void (*pxafb_backlight_power)(int);
|
|
void (*pxafb_lcd_power)(int, struct fb_var_screeninfo *);
|
|
void (*smart_update)(struct fb_info *);
|
|
};
|
|
void set_pxa_fb_info(struct pxafb_mach_info *hard_pxa_fb_info);
|
|
void set_pxa_fb_parent(struct device *parent_dev);
|
|
unsigned long pxafb_get_hsync_time(struct device *dev);
|
|
|
|
extern int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int);
|
|
extern int pxafb_smart_flush(struct fb_info *info);
|