Fix a crash caused by requests placed in the queue with the completed flag
already set. This lead to some ADB_SYNC requests returning early and their
request structs being popped off the stack while still queued. Stack corruption
ensued or an invalid request callback pointer was invoked or both. Eliminate
macii_retransmit() and its buggy implementation of macii_write(). Have
macii_queue_poll() fully initialise the request queues.
Fix a bug in macii_queue_poll() where the last_req pointer was not being set.
This caused some requests to leave the queue before being completed (and would
also corrupt the stack under certain conditions).
Fix a race in macii_start that could set the state machine to "reading" while
current_req was null.
No longer send poll commands with the ADBREQ_REPLY flag -- doing that caused
the replies to be stored in the request buffer where they were forgotten
about.
Don't autopoll by continuously sending new Talk commands. Get the controller to
do that for us. This reduces the ADB interrupt rate on an idle bus to about 5
per second. Only autopoll the devices that were probed.
Explicitly clear the interrupt flag when polling.
Use disable_irq rather than local_irq_save when polling.
Remove excess local_irq_save/restore pairs.
Improve bus timeout and service request detection.
Remove unused code (last_reply, adb_dir etc) and unneeded code (prefix_len,
first_byte etc).
Change TIP and TACK to their correct names on this ADB controller (ST_EVEN and
ST_ODD).
Add some commentry.
Add a generous quantity of sanity checks (BUG_ONs).
Let m68k macs use the adb_sync boot param too.
Tested on Mac II, Mac IIci, Quadra 650, Quadra 700 etc.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no slow IRQs on Macs since Roman Zippel's IRQ reorganisation that
went into 2.6.16 and removed mac_irq_list[] and the do_mac_irq_list()
dispatcher. (They were implemented in do_mac_irq_list() by lowering the IPL.)
Hence there's no more use for mutual exclusion in the Mac interrupt
dispatchers. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some Macs lack a slot interrupt enable register. So the existing code makes
disabled and unregistered slot IRQ lines outputs set high. This seems to work
on quadras, but does not work on genuine VIAs (perhaps the card still succeeds
in pulling the line low, or perhaps because this increases the settle time on
the port A input, meaning that the CA1 IRQ could fire before the slot line
reads active).
Because of this, the nubus_active flags were used to mask IRQs, which is
actually worse than the problem it tries to solve. Any interrupt masked by
nubus_active will remain asserted and prevent further transitions on CA1. And
so the nubus gets wedged regardless of hardware (emulated VIA ASIC, real VIA
chip or RBV).
The best solution to this hardware limitation of genuine VIAs is to disable the
umbrella SLOTS IRQ when disabling a slot on those machines. Unfortunately, this
means all slot IRQs get disabled when any slot IRQ is disabled. But it is only
a problem when there's more than 1 device using nubus interrupts.
Another potential problem for genuine VIAs is an unregistered nubus IRQ.
Eventually it will be possible to enable the CA1 interrupt by installing its
handler only _after_ all nubus drivers have loaded but _before_ the kernel
needs them, at which time this last problem can be fixed. For now it can be
worked around:
- disable MacOS extensions
- don't boot MacOS (use the Emile bootloader instead)
- get the bootloaders to disable ROM drivers (Penguin does this for video
cards already, don't know about Emile)
- physically remove unsupported cards
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure that there are no slot IRQs asserted before leaving the nubus
handler. If there are and we don't then the nubus gets wedged because this
prevents a CA1 transition, which means no more nubus IRQs.
Make the interrupt dispatch loops terminate sooner.
Explicitly initialise the VIA latches to make the code more easily understood.
Also some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reverse the last of a monumental brown-paper-bag commit that went into the 2.3
kernel.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some more machines that support A/UX interrupt priorities. There are
probably others as well, but I've only tested these ones so far.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only attempt to initialize the amount of interrupts a sun3 actually has...
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add early parameter support and convert current users to it.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat various m68k files, so they actually look like Linux sources.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atari keyboard and mouse support.
(reformating and Kconfig fixes by Roman Zippel)
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c1821c2e97 introduced the
uaccess structure that is used to select the correct set of user
copy functions for the different execution modes (standard vs.
noexec vs. z9 optimized user copy). The uaccess symbol is exported
with EXPORT_SYMBOL_GPL. This breaks all non-gpl modules that use
user copy. To make them work again change the export to
EXPORT_SYMBOL.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register aes-s390 algorithms with the actual supported max keylen size
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
And here's a port of the powerpc patch to get rid of the notifier
chain completely to s390. It's ontop of Martins patch as that one
is in mainline already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PowerNow! driver for Opteron reports the number of cores
in the system, but claims to report the number of processors.
Fix this minor cosmetic bug.
Signed-off-by: Bhavana Nagendra <bhavana.nagendra@amd.com>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
fill_powernow_table_pstate() and fill_powernow_table_fidvid() are only
defined and used for X86_POWERNOW_K8_ACPI.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
Call of_find_node_by_type with NULL instead of np
so the cpu node does not get put twice.
This was causing kref_put warnings.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use DEFINE_SPINLOCK instead of initializing spinlocks to
SPIN_LOCK_UNLOCKED, since DEFINE_SPINLOCK is better for lockdep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For dma_alloc_*()
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/timer.c:51: error: variable `timer_sysclass' has
initializer but incomplete type
arch/powerpc/sysdev/timer.c:52: error: unknown field `resume' specified in initializer
<etc>
Signed-off-by: Srinivasa Ds <srinivasa@in.ibm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just another pass through arch/powerpc for old usages.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Recently, someone fixed a syntax error in the HTDMSOUND driver
introduced 4 years ago.
Unfortunately not by trying to compile this driver for his hardware but
by code inspection - which seems to be a strong indication that there
are no users left for this OSS sound driver.
This patch therefore removes it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Dan Malek <dan@embeddedalley.com>
Acked-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_xlate_reg() looks up the 'reg' property in the specified node
to get the address and size to translate. Add dt_xlate_addr()
which is passed in the address and size to translate.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A usage of CONFIG_DEVICE_TREE got accidentally truncated; this
fix allows out-of-tree dts files to work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Why create a platform specific board_info structure that is hacked
together, ugly, and dangerous, when we've got a perfectly fine common
board_info structure that is hacked-together, ugly and dangerous.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The arch/ppc/syslib/ppc_sys.c infrastructure does not work well for the
virtex ports. Move the ml300 and ml403 board ports over to use the new
virtex_devices infrastructure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently virtex support in mainline make use of the infrastructure in
arch/ppc/syslib/ppc_sys.c for registering common devices on virtex ppc405
platforms. The ppc_sys.c code is not well suited to the dynamic nature of
FPGA designs and makes adding new board ports more complex. This patch
adds a new listing of common devices which does not depend on the ppc_sys.c
infrastructure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The header files for the ml403 and ml300 are virtually identical, merge
them into a single file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reverse dependency order for Xilinx Virtex parts. For these parts, It
makes more sense for boards/chips to specify which features they
provide instead of the features listing the parts they are implemented
in. I think it also makes adding new board ports simpler.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Shuffle Kconfig order, making the platform drivers menu depend on the global
option instead of each driver being dependent on it.
Also fix dependency of PPC_PMAC on the G5 one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 9414715a7b,
at Olaf Hering's request:
> Paul, please discard this patch. The optional graphics card may have
> also device_type 'serial' if it is in VGA mode.
> I will send an updated patch later.
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (107 commits)
smc911x: fix compilation breakage wjen debug is on
[netdrvr] eexpress: minor corrections
add NAPI support to sb1250-mac.c
ixgb: ROUND_UP macro cleanup in drivers/net/ixgb
e1000: ROUND_UP macro cleanup in drivers/net/e1000
Generic HDLC sparse annotations
e100: Optionally use I/O mode only to access register space
e100: allow bad MAC address when running with invalid eeprom csum
ehea: fix for dlpar support
ehea: fix for sysfs entries
3C509: Remove unnecessary include of <linux/pm_legacy.h>
NetXen: Fix for vmalloc issues
NetXen: Fixes for Power PC architecture
NetXen: Port swap feature for multi port cards
NetXen: Removal of redundant macros
NetXen: Multi PCI support for Quad cards
NetXen: Removal of redundant argument passing
NetXen: Use multiple PCI functions
[netdrvr e100] experiment with doing RX in a similar manner to eepro100
[PATCH] ieee80211: add missing global needed by IEEE80211_DEBUG_XXXX
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (86 commits)
SPIN_LOCK_UNLOCKED cleanup in drivers/ata/pata_winbond.c
drivers/ata/pata_cmd640.c: fix build with CONFIG_PM=n
pata_hpt37x: Further small fixes
pata_hpt3x2n: Add HPT371N support and other bits
ata: printk warning fixes
libata: separate ATA_EHI_DID_RESET into DID_SOFTRESET and DID_HARDRESET
ahci: consolidate common port flags
ata_timing: ensure t->cycle is always correct
libata: add missing call to ->cable_detect() in new EH path
pata_amd: remove contamination added during cable_detect conversion
libata: Handle drives that require a spin-up command before first access
libata: HPA support
libata: kill probe_ent and related helpers
libata: convert the remaining PATA drivers to new init model
libata: convert the remaining SATA drivers to new init model
libata: convert ata_pci_init_native_mode() users to new init model
libata: convert drivers with combined SATA/PATA ports to new init model
libata: add init helpers including ata_pci_prepare_native_host()
libata: convert native PCI host handling to new init model
libata: convert legacy PCI host handling to new init model
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (105 commits)
sonypi: use mutex instead of semaphore
sony-laptop: remove user visible camera controls as platform attributes
meye: make meye use sony-laptop instead of sonypi
sony-laptop: add a meye-usable include file for camera ops
sony-laptop: complete the motion eye camera support in sony-laptop
sonypi: try to detect if sony-laptop has already taken one of the known ioports
sonypi: suggest sonypi users to try sony-laptop instead
sony-laptop: add edge modem support (also called WWAN)
sony-laptop: add locking on accesses to the ioport and global vars
sony-laptop: add camera enable/disable parameter, better handle possible infinite loop
thinkpad-acpi: make drivers/misc/thinkpad_acpi:fan_mutex static
ACPI: thinkpad-acpi: add sysfs support to wan and bluetooth subdrivers
ACPI: thinkpad-acpi: add sysfs support to hotkey subdriver
ACPI: thinkpad-acpi: improve dock subdriver initialization
ACPI: thinkpad-acpi: improve debugging for acpi helpers
ACPI: thinkpad-acpi: improve fan control documentation
ACPI: thinkpad-acpi: map ENXIO to EINVAL for fan sysfs
ACPI: thinkpad-acpi: fix a fan watchdog invocation
ACPI: thinkpad-acpi: do not arm fan watchdog if it would not work
ACPI: thinkpad-acpi: add a fan-control feature master toggle
...
Herbert Xu conviced me that a new flag was overkill; every driver
currently overrides get_stats, so we might as well make the internal
one the default. If someone did fail to set get_stats, they would now
get all 0 stats instead of "No statistics available".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
