Use the port interrupt-out urb rather than abusing the port write_urb
pointer and allocating a new urb at every open (but the first...).
Note that the write_urb abuse would have led to a double free should
there ever be interfaces with a bulk-out endpoint.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the more efficient generic read implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor read-urb processing, and add sanity checks on header and data
lengths.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant data-offset define, which was really just the header
length.
Add payload-size define and use the bulk-out size define for the actual
bulk-out size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up and fix typos in protocol comment.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the port private data, which contains the write sequence
number, is cleared at allocation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the USB PHY layer never returns NULL we don't need
to check for that condition.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't select NOP_USB_XCEIV. Instead, board config
must select USB_PHY and the appropriate PHY driver.
Also add a hint in Kconfig so that users enabling
this driver manually enable the right PHY drivers as well.
Gets rid of the below warnings when USB_EHCI_HCD_OMAP
is enabled.
warning: (USB_EHCI_HCD_OMAP) selects NOP_USB_XCEIV which has unmet direct dependencies (USB_SUPPORT && USB_PHY)
warning: (USB_EHCI_HCD_OMAP) selects NOP_USB_XCEIV which has unmet direct dependencies (USB_SUPPORT && USB_PHY)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usbfs receives a ctrl-request from userspace it calls check_ctrlrecip,
which for a request with USB_RECIP_ENDPOINT tries to map this to an interface
to see if this interface is claimed, except for ctrl-requests with a type of
USB_TYPE_VENDOR.
When trying to use this device: http://www.akaipro.com/eiepro
redirected to a Windows vm running on qemu on top of Linux.
The windows driver makes a ctrl-req with USB_TYPE_CLASS and
USB_RECIP_ENDPOINT with index 0, and the mapping of the endpoint (0) to
the interface fails since ep 0 is the ctrl endpoint and thus never is
part of an interface.
This patch fixes this ctrl-req failing by skipping the checkintf call for
USB_RECIP_ENDPOINT ctrl-reqs on the ctrl endpoint.
Reported-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Tested-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the size of the objects by consolidating
the duplicated USB_STORAGE into a single function.
Add function usb_stor_dbg to emit debugging messages.
Always validate the format and arguments.
Reduce the number of uses of CONFIG_USB_STORAGE_DEBUG.
Reduces size of objects ~7KB when CONFIG_USB_STORAGE_DEBUG
is set.
$ size drivers/usb/storage/built-in.o*
text data bss dec hex filename
140133 55296 70312 265741 40e0d drivers/usb/storage/built-in.o.new
147494 55248 70296 273038 42a8e drivers/usb/storage/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We remove the redundant tdi_reset in ehci_setup since there
is already it in ehci_reset.
It was observed that the duplicated tdi_reset was causing
the PHY_CLK_VALID bit unstable.
Reported-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> # 3.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions have moved to include/linux/usb/samsung-usb-phy.h,
and plat/usb-phy.h is unavailable from drivers in a multiplatform
configuration.
Also fix up the plat/usb-phy.h header file to use the definitions
from the new header instead of providing a separate copy.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos5440 does not require any explict USB phy configuration. So skip
the USB phy configuration for Exynos5440 based platforms.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a sparse warning where we should be using NULL instead of 0
Cc: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.
This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.
Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch encloses all symbols depending on USB_XHCI_HCD within an if
USB_XHCI_HCD / endif block.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the various depends on USB_OHCI_HCD from the OHCI HCD
drivers and enclose them within an if USB_OHCI_HCD / endif block. The
Octeon OHCI HCD driver has been moved around to remain in this block.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thist patch removes the depends on USB_EHCI_HCD that the various USB
EHCI HCD drivers use and encloses every driver within an if USB_EHCI_HCD
/ endif block. The EHCI HCD platform and Octeon drivers have been moved
around to remain enclosed within this block.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like the OHCI counter part we just can remove the architecture
specific symbols which prevent these configuration symbols from being
selected by platforms/architectures requiring it. The original
implementation did not scale at all since it required each and every
single architecture to be added for these configuration symbols to be
selected. Now it is up to the EHCI driver and/or platform to select
these configuration symbols accordingly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
7edb3da: (USB: EHCI: make ehci-s5p a separate driver)
raised an issue with ehci-s5p's driver data.
Now that 's5p_ehci_hcd' doesn't maintain pointer to 'usb_hcd'
and s5p_ehci is nothing but a pointer to hcd->priv;
add hcd to the driver data rather than s5p_ehci.
This fixes issues with null pointer dereferencing in
s5p_ehci_shutdown(), s5p_ehci_suspend(), s5p_ehci_resume().
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
CC: Manjunath Goudar <manjunath.goudar@linaro.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Jingoo Han <jg1.han@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's three cleanup patches for 3.10. Nothing big here, just some debugging
output changes, a macro rename, and a math macro change that should have no
behavioral effects.
Tested on the Intel Panther Point xHCI host, with USB storage and mouse, with
xHCI debugging turned on. I don't have the TI host that causes the debugging
output changes to trigger.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rI06
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2012-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xHCI misc cleanup patches for 3.10
Hi Greg,
Here's three cleanup patches for 3.10. Nothing big here, just some debugging
output changes, a macro rename, and a math macro change that should have no
behavioral effects.
Tested on the Intel Panther Point xHCI host, with USB storage and mouse, with
xHCI debugging turned on. I don't have the TI host that causes the debugging
output changes to trigger.
Sarah Sharp
Separate the Qualcomm QSD/MSM on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before Qualcomm QSD/MSM
can be booted with a multi-platform kernel, which is not expected before
3.11.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the msm bus glue.
In V5 (arnd):
- add FIXME about missing usb_add_hcd() or usb_remove_hcd() calls
In V3:
- Detailed commit message added here describing why this patch is required.
- Arranged #include's in alphabetical order.
- driver.name initialized hcd_name[] = "ehci-msm" in platform_driver
structure initialization instead of "msm-ehci", which was the reason
why it broke in EHCI USB testing
In V2:
Tegra patch related changes removed from this patch.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Atmel host controller driver from ehci-hcd host code
so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before Atmel can be
booted with a multi-platform kernel. This is currently planned for
Linux-3.11.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the Atmel bus glue.
In V4 (arnd):
- reordered #include statements.
- removed call to ehci_shutdown and the corresponding export
In V3:
- Detailed commit message added here about why this patch is required.
- Replaced hcd_name string "ehci-atmel" to "atmel-ehci".
- Inserted blank line in the Makefile to separate the EHCI drivers from
the following non-EHCI drivers.
- Exported ehci_shutdown symbol as it is needed by the Atmel driver.
- Eliminated ehci_atmel_setup routine because hcd registers
can be directly set in the ehci_atmel_drv_probe function.
In V2:
Resolved below compiler error.
drivers/usb/host/ehci-atmel.c: In function 'ehci_atmel_drv_remove':
drivers/usb/host/ehci-atmel.c:167: error: implicit declaration of function 'ehci_shutdown'
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung S5P/EXYNOS host controller driver from ehci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before S5P/EXYNOS can
be booted with a multi-platform kernel. We currently expect those
to get merged for 3.10.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the s5p bus glue.
In V4 (arnd)
- revert some of the pointless changes.
- fix allocation of s5p specific data structure.
In V3:
- Detailed commit message added here, why this patch is required.
- MODULE_LICENSE is GPL v2.
- Added .extra_priv_size to eliminate the separate allocation of
the s5p_ehci_hcd structure and removed .reset function pointer
initialization.
- Arranged #include's in alphabetical order.
- After using extra_priv_size initialization, struct usb_hcd *hcd
is redundant and can be removed from the probe function.
- Eliminated s5p_ehci_phy_enable,contents of statements moved
into the s5p_ehci_probe
- Eliminated s5p_ehci_phy_disable, contents of statements moved into
the s5p_ehci_remove.
In V2:
- Tegra patch related changes removed from this patch.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the SPEAr host controller driver from ehci-hcd host code
so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before SPEAr can be
booted with a multi-platform kernel, but they are queued in the
arm-soc tree for 3.10.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the SPEAr bus glue.
In V4 (arnd):
- renamed all 'struct spear_ehci' pointers from 'ehci' to the
less ambiguous 'sehci'.
- folded trivial spear_start_ehci/spear_stop_ehci functions into
callers.
- brought back initialization of ehci->caps.
In V3:
- Detailed commit message added here about why this patch is required.
- Eliminated ehci_spear_setup routine because hcd registers can
be directly set in the spear_ehci_hcd_drv_probe function.
- spear_overrides struct initialized.
- Converted to using .extra_priv_size for allocating spear_ehci,
and updated all users of that structure.
- to_spear_ehci() macro modified for spear_ehci.
In V2:
- Replaced spear as SPEAr everywhere, leaving functions/variables/config options.
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: spear-devel@list.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Orion host controller driver from ehci-hcd host
code into its own driver module because of following reason.
With the multiplatform changes in arm-soc tree, it becomes
possible to enable the mvebu platform (which uses
ehci-orion) at the same time as other platforms that require
a conflicting EHCI bus glue. At the moment, this results
in a warning like
drivers/usb/host/ehci-hcd.c:1297:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1277:0: note: this is the location of the previous definition
drivers/usb/host/ehci-orion.c:334:31: warning: 'ehci_orion_driver' defined but not used [-Wunused-variable]
and an ehci driver that only works on one of them.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the orion bus glue.
An earlier version of this patch was included in 3.9 but caused
a regression there, which has subsequently been fixed.
While we are here, use the opportunity to disabiguate the two
Marvell EHCI controller implementations in Kconfig.
In V4 (arnd):
- Improve Kconfig text
In V3:
- More detail provided in commit message regarding this patch.
- Replaced hcd_name string "ehci-orion" into "orion-ehci".
- MODULE_LICENSE is GPL v2.
- In ehci_init_driver calling second argument passed as NULL instead of
ehci_orion_overrides because ehci_orion_overrides is removed.
In V2:
- Tegra patch related changes removed from this patch.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the appropriate WARN() and WARN_ON() accessors to avoid a build error
when CONFIG_BUG=n:
drivers/usb/gadget/configfs.c: In function 'config_usb_cfg_unlink':
drivers/usb/gadget/configfs.c:442:2: error: implicit declaration of function '__WARN_printf'
drivers/usb/gadget/configfs.c: In function 'configfs_do_nothing':
drivers/usb/gadget/configfs.c:733:2: error: implicit declaration of function '__WARN'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no functional changes in this patch. However, because the
compliance mode timer can be deleted in more than one function, it
seemed expedient to include the function name in the debug strings.
Also limited the use of capitals to the first word in the compliance
mode debug messages, except after a function name where all words
start with lower case, in keeping with the style prevalent elsewhere
in xhci.c.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
tty_port_tty_get might return a tty which is NULL. But it is
dereferenced unconditionally in edge_send. Stop dereferencing that by
sending usb_serial_port pointer around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=aF4r
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
"len" comes from the USB transfer and it's probably correct. The thing
is that we already have similar checks like:
if (data[i] >= serial->num_ports) {
So adding a sanity test here matches the rest of the code and is a good
idea.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can remove the "if (urb->actual_length) {" check because checking for
"while (i < urb->actual_length) {" is sufficient. This lets us pull the
code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Cc: stable <stable@vger.kernel.org> # v3.5
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
writeb(0xde, &td->ptr.next + 0x0); /* strb */
writeb(0xad, &td->ptr.next + 0x1); /* strb */
<----- hardware reads value of td->ptr.next and get stuck!
writeb(0xbe, &td->ptr.next + 0x2); /* strb */
writeb(0xef, &td->ptr.next + 0x3); /* strb */
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Cc: stable <stable@vger.kernel.org> # v3.5
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cleanup path checks whether the transceiver was properly initialized
using IS_ERR(). However it can also happen that the cleanup path is run
before the transceiver was initialized (or the operating mode isn't set
to TEGRA_USB_OTG) and is therefore NULL. Add a separate label for error
unwinding and initialize the transceiver field to ERR_PTR(-ENODEV) when
the operating mode isn't TEGRA_USB_OTG to allow for consistent checking.
Signed-off-by: Thierry Reding <thierry@gilfi.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To clear any configurations made by U-Boot on Tegra USB controller,
reset it before init in probe.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 756aa6b3d5 (ehci-hub: improved
over-current recovery) added port power cycling on overcurrent indications as
needed by the MPC8349 USB controller after resolving of the overcurrent
situation in order to have the host state machine assert the correct port
status again.
Commit 81463c1d70 (EHCI: only power off port if
over-current is active) solved a thus resulting issue of endless overcurrent
changes in combination with the MAX4967 USB power supply chip that signals
overcurrent when power is not enabled by only powering off a port if the
overcurrent is currently active.
Added quirks flag need_oc_pp_cycle in order to specify the needed behaviour as
there is no common behaviour that can comply with both requirements.
Activated the quirks handling for Freescale 83xx based boards.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Apple 24" LED Cinema display to the supported devices.
Signed-off-by: Ben Jencks <ben@bjencks.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
recent changes to gadget framework have
exposed a flaw in nokia.c where it uses
f_ecm.c but it wasn't including it like
other gadget drivers.
This is a temporary patch until all other
function drivers are converted to new API
where each function driver becomes a module
and binding is done through configfs.
Solves a linking error when building g_nokia.ko
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rename SEGMENT_SIZE and SEGMENT_SHIFT as the former is used in a.out.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Use ilog2() rather than __ffs() for calculating SEGMENT_SHIFT as ilog2() can
be worked out at compile time, whereas __ffs() must be calculated at runtime.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since regulator_enable() is going to be marked as __must_check in the
next merge window, always check regulator_enable() return value and
print a warning if it fails.
Cc: Hema HK <hemahk@ti.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since regulator_enable() is going to be marked as __must_check in the
next merge window, always check regulator_enable() return value and
print a warning if it fails.
Reviewed-by: Kalle Jokiniemi <kalle.jokiniemi@jollamobile.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since regulator_enable() is going to be marked as __must_check in the
next merge window, always check regulator_enable() return value and
print a warning if it fails.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
