fixed the connection problem when the private iscsi ipv4 address is
provisioned on the interface.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The nopout's reserved field was not being initialized to zero
before being reused. Stale CDB values from previous SCSI cmds
of the same BHS offset was the cause of the disconnection
initiated by the Lefthand target.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove gl_skb from cxgbi_ddp_info as it is only used by cxgb3i.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There is no need to set ulpmode on the tx skbs if no digest is enabled.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
memset arg64 to zero in the passthrough ioctls to avoid leaking contents
of kernel stack memory to userland via uninitialized padding fields
inserted by the compiler for alignment reasons.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Thanks to Scott Teel for noticing this.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Need to take the lock while accessing the register to check to
see if config table changes have taken effect.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is to prevent hpsa from resetting older boards
which the cciss driver may be controlling.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is to conserve memory in a memory-limited kdump scenario
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers. Also, only wait 10 secs
for board to become "not ready" after a reset (it should quickly
become not ready.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
They are defined in hpsa_cmd.h
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some low bits might have been set by the driver, causing
a message like this to come out:
[ 13.288062] ------------[ cut here ]------------
[ 13.293211] WARNING: at lib/dma-debug.c:803 check_unmap+0x1a1/0x654()
[ 13.300387] Hardware name: ProLiant DL180 G6
[ 13.305335] hpsa 0000:06:00.0: DMA-API: device driver tries to free
DMA memory it has not allocated [device address=0x000000007f81e001]
[size=640 bytes]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently NetApp's VID/PID details in the INQUIRY response shows up as
'NETAPP' and 'LUN'. With upcoming scalable SAN ONTAP version on NetApp
controllers, the PID entry alone is being modified to 'LUN C-Mode' (to
distinguish current ONTAP LUNs from scalable ONTAP LUNs).
'LUN' would still suffice for matching 'LUN C-Mode' but best to
explicitly add these new NetApp LUNs to the device list.
Reported-by: Martin George <marting@netapp.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds Promise VTrak devices to the ALUA device handler.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Initialize stpg_endio() 'err' to SCSI_DH_OK and only change it to
SCSI_DH_IO accordingly. This allows the switching of target group state
to be properly reported when no error has occurred.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in stpg_endio() rather than blk_put_request() -- blk_finish_request() is
called with queue lock already held.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
submit_stpg() will always return failure so alua_activate() will report
failure via dm-multipath callback function. Even though the stpg fired
successfuly dm-multipath does not know and always fails to change the
valid path.
By returning SCSI_DH_OK we're now skipping alua_activate()'s call to
activate_complete 'fn'. But this is fine because stpg_endio() will call
it via h->callback_fn().
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Upgrade driver version from 7.100.00.00 to 8.100.00.00
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Basic Code Cleanup:
(1) _base_get_cb_idx and mpt2sas_base_free_smid were reorganized in
similar fashion so the order of obtaining the cbx and smid are
scsiio,
hi_priority, and internal.
(2) The hi_priority and internal request queue struct was made
smaller
by removing the scmd and chain_tracker, thus saving memory
allocation.
(3) For scsiio request, a new structure was created having the same
elements from the former request tracker struct.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for Customer specific branding messages when device driver loads,
based on specific customer subsystem vendor and device Ids
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Revision P MPI Header Update:
a) Added enable/disable SATA NCQ operations to SAS IO Unit Control
Request.
b) Modified Host Based Discovery Action Request message format.
c) Removed Device Path bit from IO Unit Page 1 Flags field.
d) Added description of ChainOffset field for Diagnostic Data Upload
Tool.Chaining is not allowed.
Removed mpi2_history.txt file
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
SDEV_MEDIA_CHANGE event was first added by commit a341cd0f (SCSI: add
asynchronous event notification API) for SATA AN support and then
extended to cover generic media change events by commit 285e9670
([SCSI] sr,sd: send media state change modification events).
This event was mapped to block device in userland with all properties
stripped to simulate CHANGE event on the block device, which, in turn,
was used to trigger further userspace action on media change.
The recent addition of disk event framework kept this event for
backward compatibility but it turns out to be unnecessary and causes
erratic and inefficient behavior. The new disk event generates proper
events on the block devices and the compat events are mapped to block
device with all properties stripped, so the block device ends up
generating multiple duplicate events for single actual event.
This patch removes the compat event generation from both sr and sd as
suggested by Kay Sievers. Both existing and newer versions of udev
and the associated tools will behave better with the removal of these
events as they from the beginning were expecting events on the block
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace sd_media_change() with sd_check_events().
* Move media removed logic into set_media_not_present() and
media_not_present() and set sdev->changed iff an existing media is
removed or the device indicates UNIT_ATTENTION.
* Make sd_check_events() sets sdev->changed if previously missing
media becomes present.
* Event is reported only if sdev->changed is set.
This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION. For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.
[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (147 commits)
[SCSI] arcmsr: fix write to device check
[SCSI] lpfc: lower stack use in lpfc_fc_frame_check
[SCSI] eliminate an unnecessary local variable from scsi_remove_target()
[SCSI] libiscsi: use bh locking instead of irq with session lock
[SCSI] libiscsi: do not take host lock in queuecommand
[SCSI] be2iscsi: fix null ptr when accessing task hdr
[SCSI] be2iscsi: fix gfp use in alloc_pdu
[SCSI] libiscsi: add more informative failure message during iscsi scsi eh
[SCSI] gdth: Add missing call to gdth_ioctl_free
[SCSI] bfa: remove unused defintions and misc cleanups
[SCSI] bfa: remove inactive functions
[SCSI] bfa: replace bfa_assert with WARN_ON
[SCSI] qla2xxx: Use sg_next to fetch next sg element while walking sg list.
[SCSI] qla2xxx: Fix to avoid recursive lock failure during BSG timeout.
[SCSI] qla2xxx: Remove code to not reset ISP82xx on failure.
[SCSI] qla2xxx: Display mailbox register 4 during 8012 AEN for ISP82XX parts.
[SCSI] qla2xxx: Don't perform a BIG_HAMMER if Get-ID (0x20) mailbox command fails on CNAs.
[SCSI] qla2xxx: Remove redundant module parameter permission bits
[SCSI] qla2xxx: Add sysfs node for displaying board temperature.
[SCSI] qla2xxx: Code cleanup to remove unwanted comments and code.
...
Use command->sc_data_direction instead of trying (incorrectly) to
figure it out from the command itself
[jejb: fix up compile failure]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: NickCheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
according to checkstack the lpfc_fc_frame_check occupies the first
place in stack usage:
make checkstack
objdump -d vmlinux $(find . -name '*.ko') | \
perl /root/rpmbuild/BUILD/kernel-2.6.32/linux-2.6.32.x86_64/scripts/checkstack.pl x86_64
0x000013f4 lpfc_fc_frame_check [lpfc]: 1936
...
This change makes the rctl_names static, thus not on stack.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The below patch fixes a typo "diable" to "disable" and also fixes another typo in a comment.
Please let me know if this is correct or not.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The session lock is taken in threads, timers, and bottom halves
like softirqs and tasklets. All the code but
iscsi_conn/session_failure take the session lock with the spin_lock_bh
call. This was done because I thought some offload drivers
would be calling these functions from a irq. They never did,
so this patch has iscsi_conn/session_failure use the bh
locking.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
iscsi_tcp, ib_iser, cxgb*, be2iscsi and bnx2i do not use
the host lock and do not take the session lock against
a irq, so this patch drops the DEF_SCSI_QCMD use. Instead
we just take the session lock and disable bhs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If alloc_pdu fails then the task->hdr pointer may not be
set. This adds a check for this case in the cleanup callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The pdu allication callout is called from a spin lock
and in the IO path so we cannot use GFP_KERNEL. This
has the driver use GFP_ATOMIC.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This adds a more informative error code and message
for the iscsi scsi eh session drop paths. This allows
you to distinguish if the session was dropped due to
a connection failure vs the iscsi layer dropping
the session due to scsi eh failure processing.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add missing call to gdth_ioctl_free before aborting.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression buf,ha,len,addr,E;
@@
buf = gdth_ioctl_alloc(ha, len, FALSE, &addr)
... when != false buf != NULL
when != true buf == NULL
when != \(E = buf\|buf = E\)
when != gdth_ioctl_free(ha, len, buf, addr)
*return ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes unused functions, data strucutres, and definitions. It
also includes misc comment and formatting cleanups.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes some inactive functions and macros.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] fix up documentation for change in ->queuecommand to lockless calling
[SCSI] bfa: rename log_level to bfa_log_level
The semantics we employ now in the driver, performing a
BIG_HAMMER in the event of Get-ID (0x20) mailbox command
failing, should only be done for FC. On FC configurations, it
makes sense since advertising is only really performed once,
so a BIG_HAMMER to reinitiate the process is needed to
restart. Under FCoE, this is not needed, as there's a
continous stream of advertisements/ACks at the protocol layer
to initiate a relogin/reinitialization process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For driver module parameters that have permission bits set to
(S_IRUGO|S_IRUSR), remove the second term since it is already
included in the first term.
S_IRUGO comes defined as (S_IRUSR|S_IRGRP|S_IROTH).
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FCP priority info was not being updated properly in certain situations.
Here are the changes that needs to be done to take care of this issue:
1. No need to check fcport->state for FCS_UNCONFIGURED in
qla24xx_update_fcport_fcp_prio(), since an invalid loop id check is
already performed which is sufficient.
2. Add the missing qla24xx_update_fcport_fcp_prio() function call
within qla2x00_update_fcport() function, so that the priority info
is updated on every port addition or change.
3. Perform proper adapter types checking.
4. Other changes, associated with DEBUG/printk's and parameter passing.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the incorrect zero test on array new_config[].
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is just a cleanup.
The unneeded NULL check annoys static checkers because we already
derefenced it and the we check it and then (if it's not the _safe()
version) we dereference it again without checking. And the static
checker is all, "Wah? Is it null or not?"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Support is added for quiescence mode. This feature is for P3P
adapters. Any of the functions can put the firmware into quiescence
state. All the others have to ack that request. During quiescence mode
current commands are processed and all the new incoming I/Os are
blocked. Loop resync is performed after firmware comes out of
quiescence state.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
1. Change first parameter from cnic_dev to ulp_handle which is the hba
pointer. All other similar upcalls are using hba pointer. The callee
can then directly reference the hba without conversion.
2. Change return value from void to int so that an error code can be
passed back. This allows the operation to be retried.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds MegaRAID 9265/9285 (Device id 0x5b) specific code
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch adds struct megasas_instance_template changes to
the megaraid_sas driver, and changes all code to use the new instance
entries:
irqreturn_t (*service_isr )(int irq, void *devp);
void (*tasklet)(unsigned long);
u32 (*init_adapter)(struct megasas_instance *);
u32 (*build_and_issue_cmd) (struct megasas_instance *, struct scsi_cmnd *);
void (*issue_dcmd) (struct megasas_instance *instance,
struct megasas_cmd *cmd);
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch modifies the megaraid_sas driver to select the
lowest memory bar available so the driver will work in SR-IOV VF
environments where the memory bar mapping changes.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds MSI-X support and 'msix_disable' module parameter to
the megaraid_sas driver.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modify allocation to try the minimum possible page order allowed by the HBA
scatter/gather segment limit in allocation of the driver's internal
buffer. This increases the probability of successful allocation. The
allocation may still fail if this minimum order is > 0.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Reported-by: Lukas Kolbe <lkolbe@techfak.uni-bielefeld.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The order of the pages allocated for the driver buffer must be stored before
allocation because it is used in freeing already allocated pages if
allocation fails.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Reported-by: Lukas Kolbe <lkolbe@techfak.uni-bielefeld.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
set resid to the requested data-in length when a MEDIUM ERROR is
simulated. This implies no valid data is returned in the data-in
buffer
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Our current handling of medium error assumes that data is returned up
to the bad sector. This assumption holds good for all disk devices,
all DIF arrays and most ordinary arrays. However, an LSI array engine
was recently discovered which reports a medium error without returning
any data. This means that when we report good data up to the medium
error, we've reported junk originally in the buffer as good. Worse,
if the read consists of requested data plus a readahead, and the error
occurs in readahead, we'll just strip off the readahead and report
junk up to userspace as good data with no error.
The fix for this is to have the error position computation take into
account the amount of data returned by the driver using the scsi
residual data. Unfortunately, not every driver fills in this data,
but for those who don't, it's set to zero, which means we'll think a
full set of data was transferred and the behaviour will be identical
to the prior behaviour of the code (believe the buffer up to the error
sector). All modern drivers seem to set the residual, so that should
fix up the LSI failure/corruption case.
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
This reverts commit c8d2e93735.
We run into merging problems with the SCSI tree, revert this one
so it can be handled by a postmerge tree there.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch updates the GPL headers in megaraid_sas_base.c and megaraid_sas.h.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch renames megaraid_sas.c to megaraid_sas_base.c to facilitate
other files in the compile.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It seems that zero should be returned if scsi_target_is_busy(starget) is
true, no matter if sdev is on the starved list.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, when scsi_dh_activate() returns with an error
(e.g. SCSI_DH_NOSYS) the activate_complete callback is not called and
the error is not propagated to DM mpath.
When a SCSI device attached to a device handler is deleted, userland
processes currently performing I/O on the device will have their I/O
hang forever.
- Set SCSI_DH_NOSYS error when the handler is in the process of being
deleted (e.g. the SCSI device is in a SDEV_CANCEL or SDEV_DEL state).
- Set SCSI_DH_DEV_OFFLINED error when device is in SDEV_OFFLINE state.
- Call the activate_complete callback function directly from
scsi_dh_activate if an error has been set (when either the scsi_dh
internal data has already been deleted or is in the process of being
deleted).
The patch was tested in an iSCSI environment, RDAC H/W handler and
multipath. In the following reproduction process, dd will I/O hang
forever and the only way to release it will be to reboot the machine:
1) Perform I/O on a multipath device:
dd if=/dev/dm-0 of=/dev/zero bs=8k count=1000000 &
2) Delete all slave SCSI devices contained in the mpath device:
I) In an iSCSI environment, the easiest way to do this is by
stopping iSCSI:
/etc/init.d/iscsi stop
II) Another way to delete the devices is by applying the following
bash scriptlet:
dm_devs=$(ls /sys/block/ | grep dm- | xargs)
for dm_dev in $dm_devs; do
devices=$(ls /sys/block/$dm_dev/slaves)
for device in $devices; do
echo 1 > /sys/block/$device/device/delete
done
done
NOTE: when DM mpath's fail_path uses blk_abort_queue this scsi_dh change
isn't strictly required. However, DM mpath's call to blk_abort_queue
will soon be reverted because it has proven to be unsafe due to a race
(between blk_abort_queue and scsi_request_fn) that can lead to list
corruption. Therefore we cannot rely on blk_abort_queue via fail_path,
but even if we could this scsi_dh change is still preferrable.
Signed-off-by: Menny Hamburger <Menny_Hamburger@Dell.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Otherwise, after doing a RAID level migration, the disk will be
disruptively removed and re-added as a different disk on rescan.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The firmware may have been updated, in which case, it's the same device,
and in that case, we do not want to remove and add the device, we want to
let it continue as is.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updated commands used for ELS to utilize VPI
Allocate RPI at node creation time and pass in ELS commnads.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement new SLI4 init procedures based on if_type:
- Add structure changes for new SLIPORT registers and BAR changes.
- Update register names to be consistent with inteface spec terms.
- Added union to encapsulate Hardward error registers.
- Rework lpfc_sli4_post_status_check() around SLI-4's SLI_INTF type
- Removed the lpfc_sli4_fw_cfg_check routine
- Segmented driver logic to include evaluation of the if_type to
engage different behaviors.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement the FC and SLI async event handlers:
- Updated MQ_CREATE_EXT mailbox structure to include fc and SLI async events.
- Added the SLI trailer code.
- Split physical field into type and number to reflect latest SLI spec.
- Changed lpfc_acqe_fcoe to lpfc_acqe_fip to reflect latest Spec changes.
- Added lpfc_acqe_fc_la structure for FC link attention async events.
- Added lpfc_acqe_sli structure for sli async events.
- Added lpfc_sli4_async_fc_evt routine to handle fc la async events.
- Added lpfc_sli4_async_sli routine to handle sli async events.
- Moved LPFC_TRAILER_CODE_FC to be handled by its own handler function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Use for iocbq->context1 to hold the ndlp pointer.
- Set ndlp in all iocbs generated from ioctl functions.
- Turn parity and serr bits back on after performing sli4 board reset.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix iotag handling:
1) Update and check io tag for retry case.
2) Clearing upper 3 bits in io tag when an IO completes.
The 3 upper bits in io tags are used for counting FCP exchange retry.
Un-cleared bits will cause firmware to access invalid memory when the
same io tag is used for an IO to a target that doesn't support FCP
exchange retry.
3) Only check the effective bits when validating an iotag.
Other minor fixes:
1) Added trace to get FC header type with assert of unhandled packet received.
Ignore the type FC_TYPE_FC_FSS (FC_XS).
2) Fixed the adapter info display check - to check for fcmode flag even.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Direct attach is not working due to the check of PID in fcxp_send request.
- Added logic to set the lps->lp_pid with the PID assigned for n2n mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Made IOC auto_recovery synchronized and not timer based.
- Only one PCI function will attempt to recover and reinitialize
the ASIC on a failure, after all the active PCI fns
acknowledge the IOC failure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the bfa driver is loaded a flogi is sent without the knowledge of
trunking configuration. This normal flogi causes the switch ports
which had trunking enabled to go to persistent offline. Solution is
to store the port configuration (which has trunking info) in the flash
for persistency. The firmware will read this configuration when the
very first fcport enable is received.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move fw trace save logic to bfa_ioc_sm_fail_entry(),
so that fw trace is saved irrespective of the cause of the failure.
- Make bfa_ioc_sm_fail() a failure parking state.
- Rename bfa_ioc_sm_initfail() to a more appropriate bfa_ioc_sm_fail_retry()
as it is no longer a parking state.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modified scatter gather processing to use the kernel provided
scsi_for_each_sg() macro.
1) Instead of allocating and setting up sgpg in bfa_ioim_sge_setup(),
we only do allocation. As a result, we remove
bfa_ioim_sgpg_setup() and rename bfa_ioim_sge_setup() to
bfa_ioim_sgpg_alloc().
2) bfa_ioim_send_ioreq() call scsi_for_each_sg() to handle both inline
and sgpg setup.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cleaned up one line functions.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
By changing field ordering we can avoid a couple of memory holes in
the tables that use the ibmvfc_async_desc structure.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since iscsi transport can be built as a module and uses netlink socket
to communicate. The module should have an alias to autoload when socket
of NETLINK_ISCSI type is requested.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Prior to firmware state change from ACQUIRING to READY, an
0x8029 AEN is received. Added code to check previous state
being ACQUIRING in order to update the ip address in the driver.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since if fw load is failing, running on incomplete fw load would
be fatal.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
in mailbox command do not process interrupt unconditionally,
process interrupt only in polling mode
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI since
this interrupt mechanism cannot be shared like standard INTx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_DISABLE flag is deprecated and this flag is a NOOP in kernel.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The statistics for InputMegabytes and OutputMegabytes are
misnamed. They're accumulating bytes, not megabytes.
The statistic returned via /sys must be in megabytes, however,
which is what the HBA-API wants. The FCP code needs to accumulate
it in bytes and then divide by 1,000,000 (not 2^20) before it
presented via sysfs.
This affects fcoe.ko only, not fnic. The fnic driver
correctly by accumulating bytes and then converts to megabytes.
I checked that libhbalinux is using the /sys file directly without
conversion.
BTW, qla2xxx does divide by 2^20, which I'm not fixing here.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Neaten several calls to fip_select() by having it return the
pointer to the new FCF.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When there are several FCFs to choose from, the one most likely
to accept a FLOGI on certian switches is the one that last
answered a multicast solicit.
So, when receiving an advertisement, move the FCF to the front
of the list so that it gets chosen first among those with the
same priority.
Without this, more FLOGIs need to be sent in a test with
multiple FCFs and a switch in NPV mode, but it still
eventually finds one that accepts the FLOGI.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When multiple FCFs to the same fabric exist, the debug messages
all look alike. Change the message to include the MAC address.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Switches using multiple-FCFs may reject FLOGI in order to
balance the load between multiple FCFs. Even though the FCF
was available, it may have more load at the point we actually
send the FLOGI.
If the FLOGI fails, select a different FCF
if possible, among those with the same priority. If no other
FCF is available, just deliver the reject to libfc for retry.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The check for conflicting fabrics in fcoe_ctlr_select()
ignores any FCFs that aren't usable. This is a minor
problem now but becomes more pronounced after later patches.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move some of the code in fcoe_ctlr_timer_work() to
fcoe_ctlr_select() so that it can be shared
with another function in a forthcoming patch.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the announcement code to a separate function for reuse in
a forthcoming patch.
For messages regarding FCF timeout and selection, use the
previously-announced FCF MAC address (dest_addr) in the fcoe_ctlr struct.
Only print (announce) the FCF if it is new. Print MAC for
timed-out or deselected FCFs.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Frame should be freed in fc_tm_done, this is an updated patch on the one
initially submitted by Hillf Danton.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The timeout for the exchange carrying REC itself is 2 * R_A_TOV_els.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Should not continue when the abort itself is being timeout since in that case
the exchange will be deleted and relesased. We still want to call the
associated response handler to let the layer, e.g., fcp, know the exchange
itself is being timed out.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not call fc_io_compl() on fsp w/o any scsi_cmnd, e.g., lun reset is built
inside fc_fcp, not from a scsi command from queuecommnd from scsi-ml, so in
in case target is buggy that is invalid flags in the FCP_RSP, as we have seen
in some SAN Blaze target where all bits in flags are 0, we do not want to call
io_compl on this fsp.
[ Comment block added by Robert Love ]
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is very helpful to match up the corresponding exchange to the actual I/O
described by the fsp, particularly when you do a side-by-side comparison of
the syslog with your trace.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add missing newlines.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There seems rdata should get put before return.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There seems info should get freed when error encountered.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There seems info should get freed when error encountered.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We can easily remove the tgt_flags from fc_fcp_pkt struct
and use rpriv->tgt_flags directly where needed.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use the rport value for rec_tov for timeout values when
sending fcp commands. Currently, defaults are being used
which may or may not match the advertised values.
The default may cause i/o to timeout on networks that
set this value larger then the default value. To make
the timeout more configurable in the non-REC mode we
remove the FC_SCSI_ER_TIMEOUT completely allowing the
scsi-ml to do the timeout. This removes an unneeded
timer and allows the i/o timeout to be configured
using the scsi-ml knobs.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fcp packet recovery handler fc_fcp_recover() is called
when errors occurr in a fcp session. Currently it is
generically setting the status code to FC_CMD_RECOVERY for
all error types. This results in DID_BUS_BUSY errors
being returned to the scsi-ml.
DID_BUS_BUSY errors indicate "BUS stayed busy through time
out period" according to scsi.h. Many of the error reported
by fc_rcp_recovery() are pkt errors. Here we update
fc_fcp_recovery to use better host byte codes.
With certain FAST FAIL flags set DID_BUS_BUSY and DID_ERROR
will have different behaviors this was causing dm multipath
to fail quickly in some cases where a retry would be a
better action.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There seems accumulation needed.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There is a typo cleaned, which triggers memory leakage.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The error handler grabs the si->scsi_queue_lock, but
in the case where the fsp pointer is NULL it releases
the scsi_host lock. This can lead to a variety of
system hangs depending on which is used first- the
scsi_host lock or the scsi_queue_lock.
This patch simply unlocks the correct lock when fcp
is NULL.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For allocating new exch from pool, scanning for free slot in exch
array fluctuates when exch pool is close to exhaustion.
The fluctuation is smoothed, and the scan looks to be O(2).
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There seems that ep should get released, or it will no longer get freed.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This happens when then tearing down the fcoe interface with active I/O.
The back trace shows dead000000200200 in RAX, i.e., LIST_POISON2, indicating
that the fsp is already being dequeued, which is probably why no complaining
was seen in fc_fcp_destroy() about outstanding fsp not freed, since we dequeue
it in the end of fc_io_compl() before releasing it. The bug is due to the
fact that we have already destroyed lport's scsi_pkt_pool while on-going i/o
is still accessing it through fc_fcp_pkt_release(), like this trace or the
similar code path from scsi-ml to fc_eh_abort, etc. This is fixed by moving
the fc_fcp_destroy() after lport is detached from scsi-ml since fc_fcp_destroy
is supposed to called only once where no lport lock is taken, otherwise the
fc_fcp_pkt_release() would have to grab the lport lock.
BUG: unable to handle kernel NULL pointer dereference at (null)
.......
RIP: 0010:[<0000000000000000>]
[<(null)>] (null)
RSP: 0018:ffff8803270f7b88 EFLAGS: 00010282
RAX: dead000000200200 RBX: ffff880197d2fbc0 RCX: 0000000000005908
RDX: ffff880195ea6d08 RSI: 0000000000000282 RDI: ffff880180f4fec0
RBP: ffff8803270f7bc0 R08: ffff880197d2fbe0 R09: 0000000000000000
R10: ffff88032867f090 R11: 0000000000000000 R12: ffff880195ea6d08
R13: 0000000000000282 R14: ffff880180f4fec0 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8801b5820000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000001a6eae000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process fc_rport_eq (pid: 5278, threadinfo ffff8803270f6000, task ffff880326254ab0)
Stack:
ffffffffa02c39ca ffff8803270f7ba0 ffff88019331cbc0 ffff880197d2fbc0
0000000000000000 ffff8801a8c895e0 ffff8801a8c895e0 ffff8803270f7c10
ffffffffa02c4962 ffff8803270f7be0 ffffffff814c94ab ffff8803270f7c10
Call Trace:
[<ffffffffa02c39ca>] ? fc_io_compl+0x10a/0x530 [libfc]
[<ffffffffa02c4962>] fc_fcp_complete_locked+0x72/0x150 [libfc]
[<ffffffff814c94ab>] ? _spin_unlock_bh+0x1b/0x20
[<ffffffffa02b98ff>] ? fc_exch_done+0x3f/0x60 [libfc]
[<ffffffffa02c4a8f>] fc_fcp_retry_cmd+0x4f/0x60 [libfc]
[<ffffffffa02c6150>] fc_fcp_recv+0x9b0/0xc30 [libfc]
[<ffffffff8106ba7a>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107d5ec>] ? lock_timer_base+0x3c/0x70
[<ffffffff8107e06b>] ? try_to_del_timer_sync+0x7b/0xe0
[<ffffffffa02b9dcf>] fc_exch_mgr_reset+0x1df/0x250 [libfc]
[<ffffffffa02c57a0>] ? fc_fcp_recv+0x0/0xc30 [libfc]
[<ffffffffa02c1042>] fc_rport_work+0xf2/0x4e0 [libfc]
[<ffffffff8109203e>] ? prepare_to_wait+0x4e/0x80
[<ffffffffa02c0f50>] ? fc_rport_work+0x0/0x4e0 [libfc]
[<ffffffff8108c6c0>] worker_thread+0x170/0x2a0
[<ffffffff81091d50>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108c550>] ? worker_thread+0x0/0x2a0
[<ffffffff810919e6>] kthread+0x96/0xa0
[<ffffffff810141ca>] child_rip+0xa/0x20
[<ffffffff81091950>] ? kthread+0x0/0xa0
[<ffffffff810141c0>] ? child_rip+0x0/0x20
Code:
Bad RIP value.
RIP
[<(null)>] (null)
RSP <ffff8803270f7b88>
CR2: 0000000000000000
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The define for fc_seq_exch is unnecessary, since it also appears in scsi/libfc.h
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: Maggie <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Various error conditions inside ep_connect and ep_disconnect were
either not being handled or not being handled correctly. This patch
fixes all those issues.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added the handling for cases when a chip request is made to the
CNIC module but the hardware is not ready to accept. This would
lead to many unnecessary wait timeouts.
This code adds check in the connect establishment and destruction
path.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The stop path has been augmented to wait a max of 10s for all in
progress offload and destroy activities to complete before proceeding
to terminate all active connections (via iscsid or forcefully).
Note that any new offload and destroy requests are now blocked and
return to the caller immediately.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The code no longer needs to dynamically register and unregister
the CNIC device. The CNIC device will be kept registered until
module unload.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
