Switch to the more efficient generic read implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor read-urb processing, and add sanity checks on header and data
lengths.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant data-offset define, which was really just the header
length.
Add payload-size define and use the bulk-out size define for the actual
bulk-out size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up and fix typos in protocol comment.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the port private data, which contains the write sequence
number, is cleared at allocation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a sparse warning where we should be using NULL instead of 0
Cc: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.
This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.
Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_tty_get might return a tty which is NULL. But it is
dereferenced unconditionally in edge_send. Stop dereferencing that by
sending usb_serial_port pointer around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"len" comes from the USB transfer and it's probably correct. The thing
is that we already have similar checks like:
if (data[i] >= serial->num_ports) {
So adding a sanity test here matches the rest of the code and is a good
idea.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can remove the "if (urb->actual_length) {" check because checking for
"while (i < urb->actual_length) {" is sufficient. This lets us pull the
code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eba0e3c3a0.
When merged together (usb-linus and usb-next), this fix isn't needed and
causes a build error. Revert the commit to solve the build issue.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan's 'fix use-after-free in TIOCMIWAIT' patchset[1] introduces
one bug which can cause kernel hang when opening port.
This patch initialized the 'port->delta_msr_wait' waitqueue head
to fix the bug which is introduced in 3.9-rc4.
[1], http://marc.info/?l=linux-usb&m=136368139627876&w=2
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in close. This
can never happen as close is guaranteed to be called before the last tty
reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in read bulk
callback. This can never happen as the port read urb is killed (and
poisoned) at close, which in turn is guaranteed to be called before the
last tty reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in close. This
can never happen as close is guaranteed to be called before the last tty
reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary disconnect test in tiocmset. No ioctls will be made
after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we return 0 or a negative error number appropriate for
userspace on errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary disconnect test in tiocmset. No ioctls will be made
after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we return 0 or a negative error number appropriate for
userspace on errors.
Currently 1 rather than 0 is returned on successful operation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove disconnected test from close which did not protect any device IO
at all.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch modem status on carrier_raised and tiocmget.
This driver appeared to support modem-status but only read the modem
status registers once at open and then used that cached value for all
further enquires.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reimplement device type detection using the device id table and quirks.
Device type was used to detect one device type which did not support to
control functions. Add quirks to the device table and store them in the
private port data at probe instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass usb-serial port to the control functions for uart status and work
mode.
Use port device for debugging and use dev_err to report errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken uart-error handling.
This driver appears to implement uart-error handling but does not
receive status interrupts or status information with bulk in transfers.
Instead status was retrieved at open and used to flag only the first
bulk in transfer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken TIOCMIWAIT support.
This drivers appears to implement TIOCMIWAIT but has no means of
receiving modem-status interrupts.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out TIOCMIWAIT handling from custom ioctl operation and use
tiocmiwait operation field instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
