Registers some GPIOs used in magician.c with the GPIO API.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the include of the GPIO header needed to make gumstix
build. The defconfig is updated to 2.6.25 and disables PCMCIA since
that has not yet been implemented for gumstix.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
d142b6e77d added clock source support,
now it's time for the clock event support.
Tested-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These changes is the result of the discussion with Paul Walmsley.
His ideas are included into this patch.
Remove DPLL output divider handling from DPLLs and CLKOUTX2 clocks,
and place it into specific DPLL output divider clocks (e.g., dpll3_m2_clk).
omap2_get_dpll_rate() now returns the correct DPLL rate, as represented
by the DPLL's CLKOUT output. Also add MPU and IVA2 subsystem clocks, along
with high-frequency bypass support.
Add support for DPLLs function in locked and bypass clock modes.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove old PRCM register access code that is no longer needed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use shared clock code and new register
access.
Note that patch adds some temporary OLD_CK defines to keep patch
more readable. These temporary defines will be removed in the next
patch. Also not all clocks are changed in this patch to limit the
size.
Also, the patch fixes few incorrect clock defines in clock24xx.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a common clock framework for 24xx and 34xx.
Note that this patch does not add it to Makefile until in
next patch. Some functions are modified from earlier 24xx
clock framework code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves clock.h to clock24xx.c to make room for
adding common clock code for 24xx and 34xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves clock.h to clock24xx.h to make room for
adding common clock code for 24xx and 34xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes old 24xx PM code that does not really work for sleep
states, and uses old power management register access. Working PM code
will be added later.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds register access for 34xx power and clock management.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc clean-up for the mux code and remove some unnecessary
ifdefs. Patch changes debug function so it can be used on
both 24xx and 34xx.
Changes are mostly for omap2, but patch also cleans up some
omap1 and common mux code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove MPU-timer based sched_clock() in favor of the common one based
on 32k sync timer which works across all OMAP1/2/3 platforms.
Using 32k based one also gives a valid sched_clock() very early in the
boot process.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer used and similar conversions are provided
by the clocksource/clockevent code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Start cleaning up GPIO handling for OMAP5912 OSK board:
- Initialize GPIOs using the cross-platform calls, not the old
OMAP-private ones.
- Move touchscreen setup out of ads7846 code into board-specfic
setup code, where it belongs.
This doesn't depend on the patches to update OMAP to use the
gpiolib implementation framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This deprecates old set/reset_scoop_gpio interfacein favour of
support for generic gpio interface.
It requires gpiolib, so it depends on the previous patch
(gpiolib for SA-1100).
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make scoop driver use generic purpose io routines: ioread16
and iowrite16 instead of direct writing to memory.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cleanup most errors errors reported by sparse:
declare IO space as __iomem,
use %p for address printing
make functions static
Use __devinit instead of __init for scoop_init
Make scoop_remove __devexit and use __devexit_p for referencing it.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Buffalo Linkstation Pro/Live is the same hardware as the
Kurobox Pro but without the NAND flash. This patch adds a
second MACHINE_START macro to the Kurobox setup file to minimise
code duplication.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updates the CSB637 platform's D1/PB2 LED to use gpio-led by default.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the D1/PB2 LED to use the gpio-leds API and heartbeat trigger.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB637 to the new-style UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB337 target to the new UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Embest ATEB9200
Cogent CSB337
Cogent CSB637
Sperry-Sun KAFA
Picotux200
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Atmel AT91RM9200 DK
Atmel AT91RM9200 EK
Atmel AT91SAM9260 EK
Atmel AT91SAM9261 EK
Atmel AT91SAM9263 EK
Atmel AT91SAM9RL EK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bootloader on ts209 Orion boards doesn't configure the right
ethernet MAC address into the GigE unit on boot. The only way to
get the MAC address is by parsing it from the 'NAS Config' flash
partition, which is an ext2 partition that contains a file which
holds the MAC address in plain text (format "xx:xx:xx:xx:xx:xx\n")
-- this patch does that.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the GPIO-driven LEDs (using NEW_LEDS) on the Atmel
SAM9260-EK and SAM9261-EK boards.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for AT73C213 audio DAC on the Atmel SAM9260-EK and
SAM9261-EK boards.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register platform_devices for the Timer/Counter Block peripherals
found on the AT91RM9200, SAM9 & CAP9 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTT-as-RTC driver will search for the user-specified RTT
peripheral via ID number (0 .. 1).
Therefore if the processor only contains a single RTT peripheral, we
need to set its platform_device.id to "0" instead of "-1".
Also add the missing platform_device resource for the CAP9 processor.
Bug reported by Sedji Gaouaou.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Reset controller on the SAM9/CAP9 processors will store the reason
for the last system reset.
On startup, display this information (wakeup signal, RTT alarm,
watchdog reset, user reset, etc)
Based on patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Basic power-management (suspend-to-ram) support for Atmel SAM9 and
CAP9 processors.
Based on comments & patches from Anti Sullin and David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the Atmel SAM9260-EK, SAM9261-EK, SAM9263-EK and SAM9RL-EK
boards to use the new-style UART initialization.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On AT91 processors that include an ECC controller, pass its base
address to the NAND driver via platform_device resources.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable system shutdown/power-off on AT91SAM9 and AT91CAP9 based boards.
This does not require power-management to be enabled, and the
pm_power_off method can be overridden in board-specific files if
necessary.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91CAP9 processor includes the same Static Memory Controller
(SMC) peripheral as the SAM9 processors, but replaces the SDRAM
Controller with a DDR/SDR Controller (DDRSDRC).
This patch splits the existing
include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and
at91sam9_smc.h.
It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Juergen Beisert <j.beisert@pengutronix.de>
This patch cleans up the in-kernel platform code from doxygen comments.
We don't know how this could have leak in, but anyway.
Changes since last release:
- none
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Ross Wille <wille@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
prio2irq(0) is the highest prioritized interrupt. For now there is no
binary change intended.
If you intend to change the priorisation, you have to assert:
∀ x ∈ {0, 1, ⋯ 31}: (irq2prio ∘ prio2irq)(x) = x
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
The irq controller automatically masks the current and all lower prioritised
tasks until the current irq is acked.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
The hardware team changed some things that were taken as being common to
all ns9xxx processors up to now.
This patch addresses:
- irqs: s/IRQ_/IRQ_NS9360_/
- system module registers: some registers are still general, their
definition lives now in include/asm-arm/arch-ns9xxx/regs-sys-common.h.
The ns9360 specific ones are in .../regs-sys-ns9360.h
As a result ns9360_systemclock cannot be static inline any more as its
definition needs regs-sys-ns9360.h. This becomes a real problem when
adding support for ns9215 as this will need regs-sys-ns9215.h and
including both files will not work. For the same reason
ns9360_reset() is now non-inline and gpio functions live in their own
file.
- register mapping: s/ns9xxx_map_io/ns9360_map_io/
- timer registers: move time.c to time-ns9360.c;
s/ns9xxx_timer/ns9360_timer/
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
- add all available mach types for ns9xxx even if the corresponding
variables don't exist yet.
- minimize such that only relevant variables are defined. For others the
default value is used.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Now the needed structs are allocated dynamically from __init code reducing
memory usage if the kernel runs on a board different from a9m9750dev.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
1. Configuration file for YL9200
2. Board file fro YL9200
Adds support for the UCdragon YL9200 board available widly in China
Signed-off-by: steve birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes misprints in ITE 8152 interrupt demuxing
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ccoreutils and other have started using fstatat64. Thus, we
need a shim for it if we want to support modern oldabi
userlands (such as Debian/arm/lenny) with EABI kernels.
See http://bugs.debian.org/462677
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Various Orion cleanups:
- Unify GPL license banner format across all files.
- Unify naming of .h double inclusion guard preprocessor macros.
- Unify spelling of "PCIe" (variants seen: PCIE, PCIe, PCI-EX.)
- Various typo fixes.
- Remove __init attributes from prototypes declared in headers.
- Remove trailing comments from #endif statements.
- Mark a couple of locally-used-only structs static.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch enables access to the local PCIe/PCI configuration
space, and is necessary for such things as PCI Advanced Error
Recovery to work.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Move the Orion register accessor macros out of orion.h, to prevent
them from ending up in the decompressor image (Orion uncompress.h
includes orion.h.) Move them into io.h, which seems a better place
for this kind of stuff.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Instead of forcing all device bus window setup through one function
with some enum as the first argument, create separate window setup
functions for each of the four possible targets, and do the demux
internally. This allows getting rid of the window identifier enum
and the big switch statement in orion_setup_cpu_win().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion time handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion PCIe handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion IRQ handling code into plat-orion/, and add
support for multiple sets of (32) interrupts.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Create arch/arm/plat-orion/, for peripherals shared between various
Marvell Orion SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make it possible to pass mbus_dram_target_info to the sata_mv
driver via the platform data, make the sata_mv driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the SATA mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make it possible to pass mbus_dram_target_info to the ehci-orion
driver via the platform data, make the ehci-orion driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the EHCI mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make the Orion PCIe/PCI code initialise MBUS decode windows based on
mbus_dram_target_info instead of reading the info from the Orion DDR
unit decode registers directly, and move the window code with the other
PCI code, where it can be called as part of the generic PCIe/PCI init
process.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Initialise orion_mbus_dram_info on boot, and prepare for passing
this info into peripheral drivers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Platforms like iq80321 and iq80331 which may be host-bus-adapters
require 'iop3xx_init_atu=y' to be specified on the kernel command line.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The outbound translate registers should be programmed with the bus
addresses that are defined in the header files, rather than the
physical address.
Currently it doesn't matter because they're identical, but the headers
currently allow them to be different, and not using the right macros
here means that people are in for a surprise if they change them.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... otherwise we end up trying to access peripherals using wrong PCI
addresses.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the inbound and outbound memory windows debugging meaningful to
those who don't know what the register names for the ATU mean. IOW,
use plain english rather than register jargon.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix signal return code when enable CONFIG_OABI_COMPAT
Signed-off-by: Janboe Ye <janboe.ye@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are disabling write buffer coalescing. Enable it back
under linux.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_MAX is the number of the last gpio, not the number of gpios. So
the bitmap must provide GPIO_MAX + 1 bits.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definitions of ATAG_CORE and ATAG_CORE_SIZE in head.S to
head-common.S. There is no use of these in head.S itself, but they
are used in head-common.S. When building for the !CONFIG_MMU case
these were not defined when compiling head-nommu.S (which includes
head-common.S).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DNS-323, Kurobox-Pro / Linkstation-Pro, QNAP TS-109/TS-209 and some
other orion-based systems have several bogus memory entries in the tag
table, which causes the system to crash at startup. Ignore them by
resetting the tag ID to 0 in a machine fixup function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows monitoring compile issues with Kautobuild for
other omap1 boards until we have more board specific defconfig
files.
After 2.6.25, we can add a generic config_omap_generic16xx to
compile in support for all 16xx boards and then remove other
boards from OSK defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix some spinlock issues reported by lockdep: since the gpio bank
locks can be aquired in both irq and non-irq contexts, they need
to be consistent about always using the irq-safe variants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build fix:
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:720: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
H2 and H3 were broken on by e27a93a944,
which removed declarations for their tps6501x chips. This resolves
that issue for the H2. (Note that this patch *also* broke the isp1301
support on H2; it presumed a not-yet-merged new-style I2c driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of build warnings and errors in mainline for H3 boards; not
all the H3 updates were correct, it seems like the OMAP1 boards are
not getting proper build testing.
Also, commit e27a93a944 introduced a
regression related to the tps65013 chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In mainline, the "old style" I2C registration was only removed for
OMAP2, leading to init-time bugs (regressions) like:
sysfs: duplicate filename 'i2c_omap.1' can not be created
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:424 sysfs_add_one+0x40/0xd4()
Modules linked in:
... deletia ...
[<c0036a38>] (omap_init_i2c+0x0/0x50) from [<c000cea8>] (omap_init_devices+0x10/0x24)
r4:c001e000
[<c000ce98>] (omap_init_devices+0x0/0x24) from [<c0008684>] (do_initcalls+0x78/0x200)
... deletia ...
---[ end trace ca143223eefdc828 ]---
kobject_add_internal failed for i2c_omap.1 with -EEXIST, don't try to register things with the same name in the same directory.
The fix is obvious: remove the old init code, it's no longer needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes parameter passing to DMA handlers uniform between non-chained
and chained transfers and makes debugging easier. Additional data like
chain_id can be always passed to handlers via callback data if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 2f569af (CONFIG_HIGHPTE vs. sub-page page tables.) pte_free() calls
pte_lock_deinit() and dec_zone_page_state(). So free_pgd_slow must not call
the latter two when calling the first.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is unnecessary since it is already protected by
spin_lock_irq{save, restore} in clock.c.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"cat /dev/mem" may cause kernel Oops for boards with PHYS_OFFSET != 0
because character device is mapped to addresses starting from zero
and there is no protection against such situation.
Patch just add this.
Signed-off-by: Alexandre Rusev <arusev@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert debug-only (and removed) MODULE_PARM() to module_param().
Compiles cleanly (with DEBUG=1).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Wed, Feb 20, 2008 at 11:50:33AM +0100, Guennadi Liakhovetski wrote:
> arch/arm/kernel/atags.c uses for some reason the
> KEXEC_BOOT_PARAMS_SIZE macro, which is only defined if CONFIG_KEXEC
> is set. So, either this macro should be defined always, or another
> macro should be used, or ATAGS_PROC should depend on KEXEC.
As the procfs export of ATAGS is not meant as a stable, general purpose
ABI it shouldn't be an independent, general configuration option.
This patch make ATAGS_PROC depend on KEXEC
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Each call to i2c_get_adapter() must be followed by a call to
i2c_put_adapter() to release the grabbed reference. Otherwise the
reference count grows forever and the adapter can never be
unregistered.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Vladimir Ananiev <vovan888@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The .get method is needed for suspend/resume. Otherwise you
get this in dmesg:
cpufreq: suspend failed to assert current frequency is what timing core thinks it is.
cpufreq: resume failed to assert current frequency is what timing core thinks it is.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The QNAP TS-209 has its RTC interrupt on GPIO 3. Setup this
as an interrupt and pass it to the i2c_board_info.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the clock lookup always finds an entry for a specific
device and ID before it falls back to finding just by ID. This
fixes a problem reported by Holger Schurig where the BTUART was
assigned the wrong clock.
Tested-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
...
* master:
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
* omap1-upstream:
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
ARM: OMAP: Add 3430 gpio support
ARM: OMAP: Add 3430 CPU identification macros
ARM: OMAP: Request DSP memory for McBSP
* orion:
[ARM] Orion: Use the sata_mv driver for the TS-209 SATA
[ARM] Orion: Use the sata_mv driver for the Kurobox SATA
[ARM] Orion: free up kernel virtual address space
[ARM] Orion: distinguish between physical and virtual addresses
[ARM] Orion: kill orion_early_putstr()
[ARM] Orion: update defconfig
[ARM] Orion: Use the sata_mv driver for the integrated SATA controller
Fix section warning:
WARNING: arch/arm/mach-at91/built-in.o(.text+0xd74): Section mismatch in reference
from the function init_programmable_clock()
to the function .init.text:at91_css_to_clk()
The function init_programmable_clock() references
the function __init at91_css_to_clk().
This is often because init_programmable_clock lacks a __init
annotation or the annotation of at91_css_to_clk is wrong.
In this case the only calls to and from init_programmable_clock()
are from code marked as "__init", so this fix is trivially correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Uwe Kleine-Knig <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to PXA300/310 and PXA320 Developer manuals,
the ASCR[RDH] "bit needs to be cleared as part of the software
initialization coming out of any reset and coming out of D3".
The latter requirement is addressed by commit
"c4d1fb627ff3072", as for the former (coming out of any reset),
the kernel relies on boot loaders and assumes that RDH bit
is cleared there. Though, not all bootloaders follow the rule
so we have to clear the bit in kernel.
We clear the RDH bit in pxa3xx_init() function since
it is always invoked after any reset. We also preserve D1S, D2S
and D3S bits from being cleared in case we invoke pxa3xx_init()
function not from normal hardware reset (e.g. kexec scenario),
so these bits can be properly referenced later.
Signed-off-by: Dmitry Krivoschekov <dmitry.krivoschekov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch cleans up omap1 files to sync up with linux-omap tree:
- Remove omap-generic MMC config as it should be defined in board-*.c files
instead of using board-generic.c
- New style I2C board_info from David Brownell <dbrownell@users.sourceforge.net>
- Init section fixes from Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch starts using introduced I2C bus registration helper by cleaning
up registration currently done in various places and by doing necessary
board file modifications.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes omap_sram_idle() that is no longer used.
The function called in pm_idle is omap_sram_suspend, omap_sram_idle() is
not used anywhere in omap1.
Signed-off-by: Vivek Kutal <vivek.kutal@celunite.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch does the following:
- Fixes the omap_pm_idle() code so that we enter WFI mode in idle.
- /sys/power/sleep_while_idle is created only when 32k timer is used
Signed-off-by: Vivek Kutal <vivek.kutal@celunite.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use MMC multislot structures for Siemens SX1 board
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make omap1 use new MMC multislot structures. The related MMC
patches will be sent separately.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br>
Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: David Cohen <david.cohen@indt.org.br>
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_nand_platform data based on a patch
by Shahrom Sharif-Kashani <sshahrom@micron.com>, and makes
omap1 boards to use omap_nand_platform_data instead of
nand_platform_data used earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This helper module simplifies I2C bus registration for different OMAP
platforms by doing registration in one place only and to allow board
specific bus configuration like clock rate and number of busses configured.
Helper should cover OMAP processors from first to third generation.
This patch just adds the feature and current implementation cleanup and
board file modifications will be done in following patches.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DM timer support for OMAP3.
Fixed source clocks for 3430 by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanup DM timer list for OMAP2 and OMAP1 to allow
adding support for 3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DMA support for chaining and 3430.
Also remove old DEBUG_PRINTS as noted by Russell King.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 24xx GPIO debounce support. Also minor formatting
clean-up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 3430 gpio support.
It also contains a fix by Paul Walmsley <paul@pwsan.com> to use the
correct clock names for OMAP3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP1 some McBSP features depend on DSP. Also export
polling functions as suggested by Luis Cargnini.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TS-209 has a two port integrated SATA controller.
Use the sata_mv driver for this.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Kurobox has a two port integrated SATA controller.
Use the sata_mv driver for this.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Suppress A.OUT library support if CONFIG_ARCH_SUPPORTS_AOUT is not set.
Not all architectures support the A.OUT binfmt, so the ELF binfmt should not
be permitted to go looking for A.OUT libraries to load in such a case. Not
only that, but under such conditions A.OUT core dumps are not produced either.
To make this work, this patch also does the following:
(1) Makes the existence of the contents of linux/a.out.h contingent on
CONFIG_ARCH_SUPPORTS_AOUT.
(2) Renames dump_thread() to aout_dump_thread() as it's only called by A.OUT
core dumping code.
(3) Moves aout_dump_thread() into asm/a.out-core.h and makes it inline. This
is then included only where needed. This means that this bit of arch
code will be stored in the appropriate A.OUT binfmt module rather than
the core kernel.
(4) Drops A.OUT support for Blackfin (according to Mike Frysinger it's not
needed) and FRV.
This patch depends on the previous patch to move STACK_TOP[_MAX] out of
asm/a.out.h and into asm/processor.h as they're required whether or not A.OUT
format is available.
[jdike@addtoit.com: uml: re-remove accidentally restored code]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark arches that support A.OUT format by including the following in their
master Kconfig files:
config ARCH_SUPPORTS_AOUT
def_bool y
This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.
I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hack up the Orion port to distinguish between virtual and physical
addresses of register windows. This will allow moving virtual
mappings higher up in the address space, to free up more kernel
virtual address space.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds instantiation for the sata_mv driver, enabling the
integrated SATA controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As discussed on LKML some notion of 'function' is needed in
LED naming. This patch adds this to the documentation and
standardises existing LED drivers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix.c:piix_init_one() must be __devinit
sata_via.c: Remove missleading comment.
libata-core: unblacklist HITACHI drives
sata_nv: fix ATAPI issues with memory over 4GB (v7)
ata: drivers/ata/sata_mv.c needs dmapool.h
libata: kill now unused n_iter and fix sata_fsl
ahci: fix CAP.NP and PI handling
sata_mv: Support SoC controllers
Rename: linux/pata_platform.h to linux/ata_platform.h
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(with Martin Schwidefsky <schwidefsky@de.ibm.com>)
The pgd/pud/pmd/pte page table allocation functions get a mm_struct pointer as
first argument. The free functions do not get the mm_struct argument. This
is 1) asymmetrical and 2) to do mm related page table allocations the mm
argument is needed on the free function as well.
[kamalesh@linux.vnet.ibm.com: i386 fix]
[akpm@linux-foundation.org: coding-syle fixes]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the new timerfd API as it is implemented by the following patch:
int timerfd_create(int clockid, int flags);
int timerfd_settime(int ufd, int flags,
const struct itimerspec *utmr,
struct itimerspec *otmr);
int timerfd_gettime(int ufd, struct itimerspec *otmr);
The timerfd_create() API creates an un-programmed timerfd fd. The "clockid"
parameter can be either CLOCK_MONOTONIC or CLOCK_REALTIME.
The timerfd_settime() API give new settings by the timerfd fd, by optionally
retrieving the previous expiration time (in case the "otmr" parameter is not
NULL).
The time value specified in "utmr" is absolute, if the TFD_TIMER_ABSTIME bit
is set in the "flags" parameter. Otherwise it's a relative time.
The timerfd_gettime() API returns the next expiration time of the timer, or
{0, 0} if the timerfd has not been set yet.
Like the previous timerfd API implementation, read(2) and poll(2) are
supported (with the same interface). Here's a simple test program I used to
exercise the new timerfd APIs:
http://www.xmailserver.org/timerfd-test2.c
[akpm@linux-foundation.org: coding-style cleanups]
[akpm@linux-foundation.org: fix ia64 build]
[akpm@linux-foundation.org: fix m68k build]
[akpm@linux-foundation.org: fix mips build]
[akpm@linux-foundation.org: fix alpha, arm, blackfin, cris, m68k, s390, sparc and sparc64 builds]
[heiko.carstens@de.ibm.com: fix s390]
[akpm@linux-foundation.org: fix powerpc build]
[akpm@linux-foundation.org: fix sparc64 more]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the TWD_BASE macro used to set up and configure the
local timers on ARM11MPCore. The twd_base_addr and twd_size variables
are defined in localtimer.c and set from the realview_eb_init function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch sets the timer IRQ at run-time by moving the sys_timer
structure and the timer_init function to the realview_eb.c file. This
allows multiple RealView platforms to be compiled in the same kernel
image.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the get_irqnr_preamble macro to work with multiple
platforms at run-time by reading the address of the GIC controller from
the gic_cpu_base_addr variable. This variable is defined in core.c and
intialised in realview_eb.c (gic_init_irq).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the core-tile detection and only enables devices if the
corresponding tile is present. It currently detects the ARM11MPCore via
the core_tile_eb11mp() macro.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves the IRQ and DMA definitions from core.h into
realview_eb.c since they are platform-specific. It adds a
realview_eb11mp_fixup function to adjust the IRQ numbers if the
ARM11MPCore tile is fitted. The realview_smc91x_device is also moved
from core.c into realview_eb.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves the platform specific definitions from platform.h into
the board-eb.h file. It drops the INT_* definitions as they are no
longer used in irqs.h (moved to board-eb.h). It renames REALVIEW_*
macros to REALVIEW_EB_* or REALVIEW_EB11MP_* to distinguish between
standard EB and EB + the ARM11MPCore tile. The platform.h file contains
common definitions to the RealView platforms and it is only directly
included in board-*.h files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch registers the local timers on ARM11MPCore as clock event
devices. The clock device can be set up as periodic or oneshot.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds dummy local timers for each CPU so that the board clock
device is used to broadcast events to the other CPUs. The patch also
adds the declaration for the dummy_timer_setup function (the equivalent
of local_timer_setup when CONFIG_LOCAL_TIMERS is not set).
Due to the way clockevents work, the dummy timer on the first CPU has to
be registered before the board timer.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the smp_call_function_single and smp_timer_broadcast
functions and modifies ipi_timer to call the platform-specific function
local_timer_interrupt.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch updates the RealView code to the clockevents infrastructure.
The SMP support is implemented in subsequent patches. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch updates the RealView platform code to use the generic
clocksource infrastructure for basic time keeping. Based on the
Versatile implementation by Kevin Hilman.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the atags used by kexec are fixed to the ones originally used
to boot the kernel. This is less than ideal as changing the commandline,
initrd and other options would be a useful feature.
This patch exports the atags used for the current kernel to userspace
through an "atags" file in procfs. The presence of the file is
controlled by its own Kconfig option and cleans up several ifdef blocks
into a separate file. The tags for the new kernel are assumed to be at
a fixed location before the kernel image itself. The location of the
tags used to boot the original kernel is unimportant and no longer
saved.
Based on a patch from Uli Luckas <u.luckas@road.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a PXA2xx specific header file to control chip setup.
Without, the PCM027 BSP can't be built.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The is caused by the patch below:
[ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
It renamed the confusing get_hsync_len() to get_hsync_invperiod(), which
unfortunately leaves poodle.c un-modified.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some machines are missing "pxa2xx-regs.h" due to the following patch:
[ARM] pxa: move memory controller registers into pxa2xx-regs.h
This patch fixes the issue by including the pxa2xx-regs.h where necessary.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a sysdev for pxa3xx static memory controller, mainly
for register saving/restoring in PM
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. clear RDH bit after resuming back from D3, otherwise, the multi function
pins will retain the low power state
2. save/restore essential system registers
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The header file <asm/arch/ohci.h> was missing in the original file,
include it to fix the warning.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the at91sam9263, IRQs for GPIO banks C and D don't currently work.
This is because banks C, D, and E share one clock and toplevel IRQ, but
the AT91 code setting up and handling GPIO IRQs expects no sharing.
This patch:
- Fixes GPIO IRQ setup and handling to cope with GPIO banks that are
shared like on sam9263 chips, by setting up a list of those banks
and making the IRQ dispatching logic scan that list.
- Precomputes the address of each bank's registers, saving it with
other per-bank data so that it no longer needs to be constantly
recomputed during IRQs and other GPIO operations. That shrinks
hot-path code, while helping the GPIO bank irq updates.
- Fixes a minor bug where IRQ_TYPE_NONE was wrongly rejected (it just
means "use the default", which is "both edges" here).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no reason to have power control in a separate file from the
board setup code. Merge it back into the board setup file and remove
superfluous header includes.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no reason to have power control in a separate file from the
board setup code. Merge it back into the board setup file and remove
superfluous header includes.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no reason to have power control in a separate file from the
board setup code. Merge it back into the board setup file, removing
superfluous header includes and removing superfluous constants from
the machine header file.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enables the new ixp4xx qmgr and npe drivers in ixp4xx_defconfig.
Sets up the corresponding platform data for the nslu2 and nas100d
boards, and reads the ethernet MAC address from the internal flash.
Tested on both little-endian and big-endian kernels.
Tested-by: Tom King <tom@websb.net>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are the only three boards to use the IXP4XX-GPIO-LED driver, and
they can all use the new leds-gpio driver instead with no change in
functionality.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds IXDP425 platform support for two built-in 10/100 Ethernet ports.
This patch will do nothing until the actual Ethernet driver is
also included.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds drivers for IXP4xx hardware Queue Manager and for
Network Processor Engines. Requires patch #4712 (reading/writing
CPU feature (aka fuse) bits).
Posted to linux-arm-kernel on 2 Dec 2007 and revised.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds functions to read and write IXP4xx "feature" (aka "fuse")
bits, containing information about available/enabled CPU features.
The uncompress.h included by boot/compressed/misc.c resides in
a different space than rest of the kernel and thus can't use
asm/hardware.h (including asm/arch/cpu.h - which, in turn, may use
EXPORTed symbol "processor_id").
Posted to linux-arm-kernel on 2 Dec 2007 and revised.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the i2c board info related to the RTC chip on the dsmg600
board to allow it to be found automatically on boot.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the i2c board info related to the RTC chip on the nas100d
board to allow it to be found automatically on boot.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the i2c board info related to the RTC chip on the nslu2 board
to allow it to be found automatically on boot.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Remove the superfluous declaration of ctrl_alt_del().
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset on the release of the power button, so that
NAS devices which have been set to auto-power-on (by solder
bridging the power button) do not continuously power cycle.
* Remove all superflous constants from dsmg600.h
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset only after the power button has been held down
for at least two seconds. Do the reset on the release of the power
button, so that NAS devices which have been set to auto-power-on (by
solder bridging the power button) do not continuously power cycle.
* Remove all superflous constants from nas100d.h
* Add LED constants to nas100d.h while we're there.
* Update the board LED setup code to use those constants.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the defconfig for the ixp4xx machine in arch/arm/config
taking all the defaults, with the following additions:
1) Enable support for the nslu2, loft, gateway7001, wg302v2,
dsmg600, and gtwx5715 boards.
2) Enable EABI, OABI, HOTPLUG and FW_LOADER.
3) Enable the RTC subsystem, with drivers for the RTC chips on the
nslu2 (x1205) and nas100d/dsmg600 (pcf8563) boards.
4) Enable the LEDS subsystem to support the nslu2, nas100d and
dsmg600 boards. Enable the ixp4xx beeper driver.
5) Enable the USB subsystem, USB host driver support and USB mass
storage support (required for boot disk on nslu2 board).
6) Enable the ATA subsystem, with drivers for the nas100d/dsmg600
(pata_artop) and avila (ixp4xx_cf) boards.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Warning message :
WARNING: vmlinux.o(.text+0x9afc): Section mismatch: reference to .init.text:sa1110_mb_enable (between 'sa1111_probe' and 'sa1111_remove')
WARNING: vmlinux.o(.text+0x13b1ac): Section mismatch: reference to .init.text:pcmcia_jornada720_init (between 'pcmcia_probe' and 'pcmcia_remove')
* fixes the 'section mismatch' building warnings for target sa1100. Solution is __init -> __devinit. Thanks to Randy Dunlap for pointing out the solution.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move update_process_times() out from under xtime_lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After seeing the filename I'd have expected something about the
implementation of SMP in the Linux kernel - not some notes on kernel
configuration and building trivialities noone would search at this
place.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config KPROBES_SUPPORT
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
- Use HAVE_KPROBES
- Use a select
- Yet another update :
Moving to HAVE_* now.
- Update ARM for kprobes support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config ARCH_SUPPORTS_KPROBES
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
Changelog :
- Moving to HAVE_*.
- Add AVR32 oprofile.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The conflicting commit for
move-kconfiginstrumentation-to-arch-kconfig-and-init-kconfig.patch
is the ARM fix from Linus :
commit 38ad9aebe7
He just seemed to agree that my approach (just putting the missing ARM
config options in arch/arm/Kconfig) works too. The main advantage it has
is that it is smaller, does not need a cleanup in the future and does
not break the following patches unnecessarily.
It's just been discussed here
http://lkml.org/lkml/2008/1/15/267
However, Linus might prefer to stay with his own patch and I would
totally understand it that late in the release cycle. Therefore I submit
this for the next release cycle.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
A HOWTO that hasn't been updated for half a dozen years no longer
"contains valuable information about which PCI hardware does work under
Linux and which doesn't".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use gpio_vbus instead of udc_is_connected for udc on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The break_lock data structure and code for spinlocks is quite nasty.
Not only does it double the size of a spinlock but it changes locking to
a potentially less optimal trylock.
Put all of that under CONFIG_GENERIC_LOCKBREAK, and introduce a
__raw_spin_is_contended that uses the lock data itself to determine whether
there are waiters on the lock, to be used if CONFIG_GENERIC_LOCKBREAK is
not set.
Rename need_lockbreak to spin_needbreak, make it use spin_is_contended to
decouple it from the spinlock implementation, and make it typesafe (rwlocks
do not have any need_lockbreak sites -- why do they even get bloated up
with that break_lock then?).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
"make dep" is no longer required in kernel 2.6, but was still mentioned
in some places.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge together the bits of the S3C2440 and S3C2442 clock code
that can be.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the reverse of s3c2410_gpio_getirq to convert
a IRQ number into a GPIO pin number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.
Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue()
if the S3C2410_DMAF_AUTOSTART is set on the channel.
Spotted by Steven Ryu at Samsung.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c2410_dma_request() function should return the channel allocated
instead of zero for success.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.
Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.
See the code comments in the patch for more details of the process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
