This patch adds the ability to describe ethernet devices via a flattened
device tree. As device tree remains an optional feature, these bits all
need to be guarded by CONFIG_OF ifdefs.
MAC address is settable via the device tree parameter "local-mac-address";
however, the selection of the phy id is limited to probing, for now.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In KVM passthrough mode, the driver may not have config access to
non-standard registers. The BNX2_PCICFG_MISC_CONFIG config register
access to setup mailbox swapping can be done using MMIO.
Update version to 2.0.20.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5709 chip requires the BNX2_MISC_NEW_CORE_CTL_DMA_ENABLE bit to be
cleared and polling for pending DMAs to complete before chip reset.
Without this step, we've seen NMIs during repeated resets of the chip.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the vlan device is lockless and single queue do not
transfer the real num queues. This is causing a BUG_ON to occur.
kernel BUG at net/8021q/vlan.c:345!
Call Trace:
[<ffffffff813fd6e8>] ? fib_rules_event+0x28/0x1b0
[<ffffffff814ad2b5>] notifier_call_chain+0x55/0x80
[<ffffffff81089156>] raw_notifier_call_chain+0x16/0x20
[<ffffffff813e5af7>] call_netdevice_notifiers+0x37/0x70
[<ffffffff813e6756>] netdev_features_change+0x16/0x20
[<ffffffffa02995be>] ixgbe_fcoe_enable+0xae/0x100 [ixgbe]
[<ffffffffa01da06a>] vlan_dev_fcoe_enable+0x2a/0x30 [8021q]
[<ffffffffa02d08c3>] fcoe_create+0x163/0x630 [fcoe]
[<ffffffff811244d5>] ? mmap_region+0x255/0x5a0
[<ffffffff81080ef0>] param_attr_store+0x50/0x80
[<ffffffff810809b6>] module_attr_store+0x26/0x30
[<ffffffff811b9db2>] sysfs_write_file+0xf2/0x180
[<ffffffff8114fc88>] vfs_write+0xc8/0x190
[<ffffffff81150621>] sys_write+0x51/0x90
[<ffffffff8100c0b2>] system_call_fastpath+0x16/0x1b
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing struct netdev_queue state against FROZEN bit, we also test
XOFF bit. We can test both bits at once and save some cycles.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. IPV6_TLV_TEL_DST_SIZE
This has not been using for several years since created.
2. RT6_INFO_LEN
commit 33120b30 kill all RT6_INFO_LEN's references, but only this definition remained.
commit 33120b30cc
Author: Alexey Dobriyan <adobriyan@sw.ru>
Date: Tue Nov 6 05:27:11 2007 -0800
[IPV6]: Convert /proc/net/ipv6_route to seq_file interface
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kdump environment do not depend on reset_devices
parameter to reset the device as the parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the device
needs a reset.
Driver maintains a count of number of pci functions probed
and decrements the count when remove handler of that pci function
is called. If the first probe, probe of function 0,
detects the count as non zero then reset the device.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kdump environment do not depend upon reset_devices parameter
to reset the pci function as this parameter may become obsolete.
Instead use an adapter specific mechanism to determine if the pci
function needs to be reset.
Per function refcount is maintained in driver, which is set in probe
and reset in remove handler of adapter. If the probe detects the count
as non zero then reset the function.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros have been existed for several years since v2.6.12-rc2.
But they never be used. So remove them now.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key changes are:
- EQ ids are not assigned consecutively in Lancer. So, fix mapping of MSIx
vector to EQ-id.
- BAR mapping and some req locations different for Lancer.
- TCP,UDP,IP checksum fields must be compulsorily set in TX wrb for TSO in
Lancer.
- CEV_IST reg not present in Lancer; so, peek into event queue to check for
new entries
- cq_create and mcc_create cmd interface is different for Lancer; handle
accordingly
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Categorize AR7010 & AR9287 devices based on driver_info
of usb_device_id, instead of PIDs. This avoids per-device cases
and minimize code changes for new device addition.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 devices (PCI/USB) use different eeprom start location
to read nvram. New devices might endup with same devid. So use
driver_info to set offset, instead of devid. driver_info is
valid for HTC devices alone which is filled in usb_device_id.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver_info stores the device category information which
is used to load appropriate device firmware, select firmware offset
and eeprom starting location. The driver_info is accessed across
ath9k_htc and ath9k_hw. Hence placed under common structure.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6000g2b and up, adding advance power management support
for better power consumption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If shadow register is enable, modify the power management
command to inform uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the BT PSPoll flag when fill PM command to uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding additional power management option available for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 7 of BT config flag is used to enable/disable PSPoll sync.
Make the name to match it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For drivers that have accurate TX status reporting
we can report the number of consecutive lost packets
to userspace using the new cfg80211 CQM event. The
threshold is fixed right now, this may need to be
improved in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since nullfunc frames are transmitted as unicast frames, they're more
reliable than the broadcast probe requests, so we need fewer retries
to figure out whether the AP is really gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nullfunc frames are better for connection monitoring, because probe requests
are answered even if the AP has already dropped the connection, whereas
nullfunc frames from an unassociated station will trigger a disassoc/deauth
frame from the AP (WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA), which allows
the station to reconnect immediately instead of waiting until it attempts to
transmit the next unicast frame.
This only works on hardware with reliable tx ACK reporting, any other hardware
needs to fall back to the probe request method.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the connection by probing the AP (either using nullfunc or a
probe request). If nullfunc probing is supported and the assoc is no
longer valid, the AP will send a disassoc/deauth immediately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a fixed 2 second timeout, calculate beacon loss interval
from the advertised beacon interval and a frame count. With this beacon
loss happens after N (default 7) consecutive frames are missed which
for a typical setup (100TU beacon interval) is ~700ms (or ~1/3 previous).
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some typos, warnings, initialize some values to follow wl's code path.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Additional comment by Larry Finger <Larry.Finger@lwfinger.net>:
This change deserves a bit more explanation. You might include something like
"These tables came from reverse engineering the 5.10.56.46 version of the
Broadcom driver. Trace comparisons between b43 and the current Broadcom driver
(5.10.120.0) show byte reversals for the PHY register writes."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No change in output for pr_<level> prefixes.
netdev_<level> output is different, arguably improved.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
