Convert the ColdFire 54xx CPU General Timer register address definitions to
include the MCF_MBAR peripheral region offset. This makes them consistent
with all other 54xx address register definitions (in m54xxsim.h).
The goal is to reduce different definitions used (some including offsets and
others not) causing bugs when used incorrectly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The Pin Assignment register definitions for the ColdFire 54xx CPU family are
inconsistently named and defined compared to the other ColdFire part
definitions. Rename them with the same prefix as used on other parts,
MCFGPIO_PAR_, and make their definitions include the MCF_MBAR periphperal
region offset.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The multi-function pin setup code for the FEC ethernet module is using just
plain wrong. Looks like it was cut-and-pasted from other init code. It has
hard coded register addresses that are incorrect for the 523x, and it is
manipulating bits that don't make sense.
Add proper register definitions for the Pin Assignment registers of the 532x,
and then use them to fix the setup code for the FEC hardware module.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Move the base address defines of the ColdFire 54xx CPU slice timers into the
54xx specific header (m54xxsim.h). They are CPU specific, and belong with the
CPU specific defines. Also make them relative to the MBAR peripheral region,
making the define the absolute address.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Get rid of the use of local IO access macros and switch to using the standard
read*/write* family of access functions for the ColdFire m532x setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 532x CPU register definitions for the multi-function setup
pins are inconsistently defined compared with other ColdFire parts. Modify
the register defintions to be just the addresses, not pointers. This also
fixes the erroneous use in one case of using these values in the UART setup
code for the 532x.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the setup code for the FEC multi-function pins on the ColdFire 528x
has the addresses hard coded in the code. Use the register defines that
already exist for this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the last address definitions relative to the IPSBAR peripheral region
for the ColdFire 527x family. This involved cleaning up some magic numbers
used in the code part, and making them proper register definitions in the 527x
specific header.
This is part of the process of cleaning up the ColdFire register definitions
to make them consistently use absolute addresses for the primary registers.
This will reduce the occasional bugs caused by inconsistent definition of
the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The registers used to configure and set the multifunction pins on the 5272
ColdFire are defined as absolute addresses. So the use of them does not need
to be offset relative to the peripheral region address.
Fix two cases of incorrect usage of these addresses. Both affect UART
initialization, one in the common UART pin setup code, the other in the
NETtel board specific UART signal handling.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make the ColdFire 5249 MBAR peripheral register definitions absolute
addresses, instead of offsets into the region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make the remaining definitions of the 5272 ColdFire registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Chip Select registers absolute addresses.
Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Interrupt Source registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Software watchdog registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Reset and System registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the abolsute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Interrupt Mask and Pending registers
absolute addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
DRAGEN2 should obviously be CONFIG_DRAGEN2, but the screen.h entry it
triggers only references files that are nowhere to be found in the
current tree. Besides, nothing uses screen.h. So just drop all that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The managed clk functions are currently only available when the generic clk
lookup framework is build. But the managed clk functions are merely wrappers
around clk_get and clk_put and do not depend on any specifics of the generic
lookup functions and there are still quite a few custom implementations of the
clk API. So make the managed functions available whenever the clk API is
implemented.
The patch also removes the custom implementation of devm_clk_get for the
coldfire platform.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Make sys_atomic_cmpxchg_32 work on classic m68k
m68k/apollo: Rename "timer" to "apollo_timer"
zorro: Remove unused zorro_bus.devices
m68k: Remove never used asm/shm.h
m68k/sun3: Remove unselectable code in prom_init()
m68k: Use asm-generic version of <asm/sections.h>
m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
mtd/uclinux: Use generic __bss_stop instead of _ebss
m68knommu: Allow ColdFire CPUs to use unaligned accesses
m68k: Remove five unused headers
m68k: CPU32 does not support unaligned accesses
m68k: Introduce config option CPU_HAS_NO_UNALIGNED
m68k: delay, muldi3 - Use CONFIG_CPU_HAS_NO_MULDIV64
m68k: Move CPU_HAS_* config options
m68k: Remove duplicate FPU config option
m68knommu: Clean up printing of sections
m68k: Use asm-generic version of <asm/types.h>
m68k: Use Kbuild logic to import asm-generic headers
The ColdFire M54xx SoC family have a traditional PCI bus interface.
Add the core support code to access and use this bus on these parts.
This code provides all the config space access functions and IO access
functions. It also carries out the PCI bus initialization and hooks into
the kernel PCI subsystem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Quite a few of Freescale's older ColdFire development boards used an NS8390
based ethernet interface. Add a platform definition for the resources used
by these devices so we can use it on these boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 532x has individually controllable clocks for it peripherals. Add clk
definitions for these and add default initialization of either enabled or
disabled.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 520x has individually controllable clocks for its peripherals. Add clk
definitions for these and add default initialization of either enabled or
disabled for all of the clocks.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add support for the Coldfire 5441x (54410/54415/54416/54417/54418). Currently
we only support noMMU mode. It requires the PIT patch posted previously as it
uses the PIT instead of the dma timer as a clock source so we can get all that
GENERIC_CLOCKEVENTS goodness. It also adds some simple clk definitions and
very simple minded power management. The gpio code is tweeked and some
additional devices are added to devices.c. The Makefile uses -mv4e as
apparently, the only difference a v4m (m5441x) and a v4e is the later has a
FPU, which I don't think should matter to us in the kernel.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1 so we can support
those parts that have the pit1 interrupt on other than the first interrupt
controller.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
If we're not connecting external GPIO extenders via i2c or spi or whatever, we
probably don't need GPIOLIB. If we provide an alternate implementation of
the GPIOLIB functions to use when only on-chip GPIO is needed, we can change
ARCH_REQUIRE_GPIOLIB to ARCH_WANTS_OPTIONAL_GPIOLIB so that GPIOLIB becomes
optional.
The downside is that in the GPIOLIB=n case, we lose all error checking done by
gpiolib, ie multiply allocating the gpio, free'ing gpio etc., so that the
only checking that can be done is if we reference a gpio on an external part.
Targets that need the extra error checking can still select GPIOLIB=y.
For the case where GPIOLIB=y, we can simplify the table of gpio chips to use a
single chip, eliminating the tables of chips in the 5xxx.c files. The
original motivation for the definition of multiple chips was to match the way
many of the Coldfire variants defined their gpio as a spare array in memory.
However, all this really gains us is some error checking when we request a
gpio, gpiolib can check that it doesn't fall in one of the holes. If thats
important, I think we can still come up with a better way of accomplishing
that.
Also in this patch is some general cleanup and reorganizing of the gpio header
files (I'm sure I must have had a reason why I sometimes used a prefix of
mcf_gpio and other times mcfgpio but for the life of me I can't think of it
now).
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
BSS_SECTION() provides the __bss_{start,stop} symbols, so there's no need
to wrap our own _[se]bss around it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer<gerg@uclinux.org>
Commit f4d40de39a ("net fec: do not depend
on grouped clocks") breaks compilation of the FEC driver for non iMX
platforms in linux-3.5-rc1. For example when compiling for ColdFire I get:
LD vmlinux
drivers/built-in.o: In function `fec_probe':
fec.c:(.devinit.text+0x1e0): undefined reference to `devm_clk_get'
Define a simple devm_clk_get() function for the m68knommu architecture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for 68360 based targets fails with:
arch/m68k/platform/68360/config.c: In function ‘hw_tick’:
arch/m68k/platform/68360/config.c:55:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68360/config.c: At top level:
arch/m68k/platform/68360/config.c:64:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for 68328 based targets fails with:
arch/m68k/platform/68328/timers.c: In function ‘hw_tick’:
arch/m68k/platform/68328/timers.c:65:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68328/timers.c: At top level:
arch/m68k/platform/68328/timers.c:102:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pull first series of signal handling cleanups from Al Viro:
"This is just the first part of the queue (about a half of it);
assorted fixes all over the place in signal handling.
This one ends with all sigsuspend() implementations switched to
generic one (->saved_sigmask-based).
With this, a bunch of assorted old buglets are fixed and most of the
missing bits of NOTIFY_RESUME hookup are in place. Two more fixes sit
in arm and um trees respectively, and there's a couple of broken ones
that need obvious fixes - parisc and avr32 check TIF_NOTIFY_RESUME
only on one of two codepaths; fixes for that will happen in the next
series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (55 commits)
unicore32: if there's no handler we need to restore sigmask, syscall or no syscall
xtensa: add handling of TIF_NOTIFY_RESUME
microblaze: drop 'oldset' argument of do_notify_resume()
microblaze: handle TIF_NOTIFY_RESUME
score: add handling of NOTIFY_RESUME to do_notify_resume()
m68k: add TIF_NOTIFY_RESUME and handle it.
sparc: kill ancient comment in sparc_sigaction()
h8300: missing checks of __get_user()/__put_user() return values
frv: missing checks of __get_user()/__put_user() return values
cris: missing checks of __get_user()/__put_user() return values
powerpc: missing checks of __get_user()/__put_user() return values
sh: missing checks of __get_user()/__put_user() return values
sparc: missing checks of __get_user()/__put_user() return values
avr32: struct old_sigaction is never used
m32r: struct old_sigaction is never used
xtensa: xtensa_sigaction doesn't exist
alpha: tidy signal delivery up
score: don't open-code force_sigsegv()
cris: don't open-code force_sigsegv()
blackfin: don't open-code force_sigsegv()
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
TIF_NOTIFY_RESUME added (as bit 5). That way nommu glue needs no changes at
all; mmu one needs just to replace jmi do_signal_return to jne do_signal_return
There we have flags shifted up, until bit 6 (SIGPENDING) is in MSBit; instead
of checking that MSBit is set (jmi) we check that MSBit or something below it
is set (jne); bits 0..4 are never set, so that's precisely "bit 6 or bit 5 is
set".
Usual handling of NOTIFY_RESUME/SIGPENDING is done in do_notify_resume(); glue
calls it instead of do_signal().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
