This patch allows you to create a new network namespace
using sys_clone, or sys_unshare.
As the network namespace is still experimental and under development
clone and unshare support is only made available when CONFIG_NET_NS is
selected at compile time.
As this patch introduces network namespace support into code paths
that exist when the CONFIG_NET is not selected there are a few
additions made to net_namespace.h to allow a few more functions
to be used when the networking stack is not compiled in.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sysfs support is compiled out the kernel still keeps and maintains
the kobject tree. So it is not safe to skip our kobject reference counting or
to avoid becoming members of the kobject tree. It is safe to not add
the networking specific sysfs attributes.
This patch removes the sysfs special cases from net/core/dev.c
renames functions from netdev_sysfs_xxxx to netdev_kobject_xxxx
and always compiles in net-sysfs.c
net-sysfs.c is modified with a CONFIG_SYSFS guard around the parts
that are actually sysfs specific.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DCCP requires to close both ends of a connection simultaneously,
permission to write in state DCCP_CLOSING is removed in dccp_sendmsg():
* if the sending end closed, it would encounter a write error anyhow;
* if the other end has closed the connection, it accepts no more data.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This factors code common to dccp_v{4,6}_ctl_send_reset into a separate function,
and adds support for filling in the Data 1 ... Data 3 fields from RFC 4340, 5.6.
It is useful to have this separate, since the following Reset codes will always
be generated from the control socket rather than via dccp_send_reset:
* Code 3, "No Connection", cf. 8.3.1;
* Code 4, "Packet Error" (identification for Data 1 added);
* Code 5, "Option Error" (identification for Data 1..3 added, will be used later);
* Code 6, "Mandatory Error" (same as Option Error);
* Code 7, "Connection Refused" (what on Earth is the difference to "No Connection"?);
* Code 8, "Bad Service Code";
* Code 9, "Too Busy";
* Code 10, "Bad Init Cookie" (not used).
Code 0 is not recommended by the RFC, the following codes would be used in
dccp_send_reset() instead, since they all relate to an established DCCP connection:
* Code 1, "Closed";
* Code 2, "Aborted";
* Code 11, "Aggression Penalty" (12.3).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This replaces normal addition with mod-48 addition so that sequence number
wraparound is respected.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This implements a SHOULD from RFC 4340, 7.5.4:
"To protect against denial-of-service attacks, DCCP implementations SHOULD
impose a rate limit on DCCP-Syncs sent in response to sequence-invalid packets,
such as not more than eight DCCP-Syncs per second."
The rate-limit is maintained on a per-socket basis. This is a more stringent
policy than enforcing the rate-limit on a per-source-address basis and
protects against attacks with forged source addresses.
Moreover, the mechanism is deliberately kept simple. In contrast to
xrlim_allow(), bursts of Sync packets in reply to sequence-invalid packets
are not supported. This foils such attacks where the receipt of a Sync
triggers further sequence-invalid packets. (I have tested this mechanism against
xrlim_allow algorithm for Syncs, permitting bursts just increases the problems.)
In order to keep flexibility, the timeout parameter can be set via sysctl; and
the whole mechanism can even be disabled (which is however not recommended).
The algorithm in this patch has been improved with regard to wrapping issues
thanks to a suggestion by Arnaldo.
Commiter note: Rate limited the step 6 DCCP_WARN too, as it says we're
sending a sync.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
In this patch, duplicated code is removed for the case when a Reset packet is
sent from a connected socket. This code duplication is between dccp_make_reset
and dccp_transmit_skb, which already contained an (up to now entirely unused)
switch statement to fill in the reset code from the DCCP_SKB_CB.
The only thing that has been removed is the call to dst_clone(dst), since
the queue_xmit functions use sk_dst_cache anyway.
I wasn't sure which purpose inet_sk_rebuild_header served, so I left it in.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds fields to support the informational Data 1..3 fields of the
DCCP-Reset packets (RFC 4340, 5.6), and makes minor cosmetic changes
to documentation.
Code which fills in these fields follows in subsequent patches, it is
primarily used for reporting option-processing and feature-negotiation
errors.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds a FIXME to signal that the function dccp_send_delayed_ack is nowhere
used in the entire DCCP/CCID code.
Using a delayed Ack timer is suggested in 11.3 of RFC 4340, but it has also
rather subtle implications for the Ack-Ratio-accounting.
CCID2 does not use this (maybe it should).
I think leaving the function in is good, in case someone wants to implement
this.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This moves several instances of testing against NULL into the function which is
used to de-reference the CCID-private data.
Committer note: Made the BUG_ON depend on having CONFIG_IP_DCCP_CCID3_DEBUG, as it
is too much to have this on production code. Also made sure that
the macro is used only after checking if sk_state is not LISTEN,
to make it equivalent to what we had before.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This fixes the code to correspond to RFC 4340, 7.5.4, which states the
exception that a Sync received in state REQUEST generates a Reset (not
a SyncAck).
To achieve this, only a small change is required. Since
dccp_rcv_request_sent_state_process() already uses the correct Reset Code
number 4 ("Packet Error"), we only need to shift the if-statement a few
lines further down.
(To test this case: replace DCCP_PKT_RESPONSE with DCCP_PKT_SYNC
in dccp_make_response.)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This patch:
- makes hidp_setup_input() return int to indicate errors;
- checks its return value to handle errors.
And this time it is against -rc7-mm1 tree.
Thanks to roel and Marcel Holtmann for comments.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of ACK reordering, the SACK block might be valid in it's
time but is already obsoleted since we've received another kind
of confirmation about arrival of the segments through snd_una
advancement of an earlier packet.
I didn't bother to build distinguishing of valid and invalid
SACK blocks but simply made reordered SACK blocks that are too
old always not counted regardless of their "real" validity which
could be determined by using the ack field of the reordered
packet (won't be significant IMHO).
DSACKs can very well be considered useful even in this situation,
so won't do any of this for them.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
I previously added checking to position that is rather poor as
state has already been adjusted quite a bit. Re-placing it above
all state changes should be more robust though the return should
never ever get executed regardless of its place :-).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter `seq' of dccp_send_sync() is in fact an acknowledgement number
and not a sequence number - thus renamed by this patch into `ackno'.
Secondly, a `critical' warning is added when a Sync/SyncAck could not be sent.
Sanity: I have checked all other functions that are called in dccp_transmit_skb,
there are no clashes with the use of dccpd_ack_seq; no other function is
using this slot at the same time.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates sequence number checking with regard to RFC 4340, 7.5.4.
Missing in the code was an exception for sequence-invalid Reset packets,
which get a Sync acknowledging GSR, instead of (as usual) P.seqno.
This can lead to an oscillating ping-pong flood of Reset packets.
In fact, it has been observed on the wire as follows:
1. client establishes connection to server;
2. before server can write to client, client crashes without notifying
the server (NB: now no longer possible due to ABORT function);
3. server sends DCCP-Data packet (has no ackno);
4. client generates Reset "No Connection", seqno=0, increments seqno;
5. server replies with Sync, using ackno = P.seqno;
6. client generates Reset "No Connection" with seqno = ackno + 1;
7. goto (5).
The difference is that now in (5) the server uses GSR. This causes the
Reset sent by the client in (6) to become sequence-valid, so that in (7)
the vicious circle is broken; the Reset is then enqueued and causes the
socket to enter TIMEWAIT state.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is in part required by the next patch; it
* replaces 6 instances of `DCCP_SKB_CB(skb)->dccpd_seq' with `seqno';
* replaces 7 instances of `DCCP_SKB_CB(skb)->dccpd_ack_seq' with `ackno';
* replaces 1 use of dccp_inc_seqno() by unfolding `ADD48' macro in place.
No changes in algorithm, all changes are text replacement/substitution.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The third parameter of dccp_sample_rtt now becomes useless and is removed.
Also combined the subtraction of the timestamp echo and the elapsed time.
This is safe, since (a) presence of timestamp echo is tested first and (b)
elapsed time is either present and non-zero or it is not set and equals 0
due to the memset in dccp_parse_options.
To avoid measuring option-processing time, the timestamp for measuring the
initial Request/Response RTT sample is taken directly when the function is
called (the Linux implementation always adds a timestamp on the Request,
so there is no loss in doing this).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a timesource, conveniently used for DCCP timestamps, which
returns the elapsed time in 10s of microseconds since initialisation.
This makes for a wrap-around time of about 11.9 hours, which should be
sufficient for most applications.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the number of timestamps taken in the receive path
for each packet.
The ccid3_hc_tx_update_x() routine is called in
* the receive path for each CCID3-controlled packet
* for the nofeedback timer (if no feedback arrives during 4 RTT)
Currently, when there is no loss, each packet gets timestamped twice.
The patch resolves this by recycling the first timestamp taken on packet
reception for RTT sampling.
When the no_feedback_timer() is called, then the timestamp argument is
simply set to NULL - so that ccid3_hc_tx_update_x() takes care of the logic.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Might as well rename ieee80211_cfg.h to cfg.h to keep things consistent.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each station has a vlan_id that is useless. Remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parse result typedef isn't needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's just painful to have the extra ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mac80211 print out the wiphy name instead of the
master device name where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a warning about NUM_IEEE80211_MODES missing
in a switch statement. Intentionally do not add a default
case so we get warnings at these places if we need to add
new modes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the key threshold stuff from mac80211.
I have patches for later that add it as a per-key setting
to nl/cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows drivers to indicate bad FCS/PLCP CRC to the stack and
have the stack drop packets like that except for monitor interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for disabling the radio and setting the TXpower
through wext.
This also fixes the prism TXpower ioctl (It always overwrote the TXpower
value in ieee80211_hw_config())
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems I was actually able to hit this deadlock, on my quad G5 softmac
locks up more often than not. This fixes it by using an own workqueue
that can safely be flushed under RTNL.
Not sure if the patch is correct with the workqueue naming. And don't
think with the patch it doesn't continually lock up. It still does, just
doesn't invoke lockdep warnings all the time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For N cpus, with full throttle traffic on all N CPUs, funneling traffic
to the same ethernet device, the devices queue lock is contended by all
N CPUs constantly. The TX lock is only contended by a max of 2 CPUS.
In the current mode of operation, after all the work of entering the
dequeue region, we may endup aborting the path if we are unable to get
the tx lock and go back to contend for the queue lock. As N goes up,
this gets worse.
The changes in this patch result in a small increase in performance
with a 4CPU (2xdual-core) with no irq binding. Both e1000 and tg3
showed similar behavior;
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason to clear the sacktag skb hint when small part
of the rexmit queue changes. Account changes (if any) instead when
fragmenting/collapsing. RTO/FRTO do not touch SACKED_ACKED bits so
no need to discard SACK tag hint at all.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the description that follows comes from my mail to
netdev (some editing done):
Main obstacle to FRTO use is its deployment as it has to be on
the sender side where as wireless link is often the receiver's
access link. Take initiative on behalf of unlucky receivers and
enable it by default in future Linux TCP senders. Also IETF
seems to interested in advancing FRTO from experimental [1].
How does FRTO help?
===================
FRTO detects spurious RTOs and avoids a number of unnecessary
retransmissions and a couple of other problems that can arise
due to incorrect guess made at RTO (i.e., that segments were
lost when they actually got delayed which is likely to occur
e.g. in wireless environments with link-layer retransmission).
Though FRTO cannot prevent the first (potentially unnecessary)
retransmission at RTO, I suspect that it won't cost that much
even if you have to pay for each bit (won't be that high
percentage out of all packets after all :-)). However, usually
when you have a spurious RTO, not only the first segment
unnecessarily retransmitted but the *whole window*. It goes like
this: all cumulative ACKs got delayed due to in-order delivery,
then TCP will actually send 1.5*original cwnd worth of data in
the RTO's slow-start when the delayed ACKs arrive (basically the
original cwnd worth of it unnecessarily). In case one is
interested in minimizing unnecessary retransmissions e.g. due to
cost, those rexmissions must never see daylight. Besides, in the
worst case the generated burst overloads the bottleneck buffers
which is likely to significantly delay the further progress of
the flow. In case of ll rexmissions, ACK compression often
occurs at the same time making the burst very "sharp edged" (in
that case TCP often loses most of the segments above high_seq
=> very bad performance too). When FRTO is enabled, those
unnecessary retransmissions are fully avoided except for the
first segment and the cwnd behavior after detected spurious RTO
is determined by the response (one can tune that by sysctl).
Basic version (non-SACK enhanced one), FRTO can fail to detect
spurious RTO as spurious and falls back to conservative
behavior. ACK lossage is much less significant than reordering,
usually the FRTO can detect spurious RTO if at least 2
cumulative ACKs from original window are preserved (excluding
the ACK that advances to high_seq). With SACK-enhanced version,
the detection is quite robust.
FRTO should remove the need to set a high lower bound for the
RTO estimator due to delay spikes that occur relatively common
in some environments (esp. in wireless/cellular ones).
[1] http://www1.ietf.org/mail-archive/web/tcpm/current/msg02862.html
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically this change enables it, previously other undo_marker
users were left with nothing. Reverse undo_marker logic
completely to get it set right in CA_Loss. On the other hand,
when spurious RTO is detected, clear it. Clearing might be too
heavy for some scenarios but seems safe enough starting point
for now and shouldn't have much effect except in majority of
cases (if in any).
By adding a new FLAG_ we avoid looping through write_queue when
RTO occurs.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements following cleanups:
- Comment re-placement (CodingStyle)
- tcp_tso_acked() local (wrapper-like) variable removal
(readability)
- __-types removed (IMHO they make local variables jumpy looking
and just was space)
- acked -> flag (naming conventions elsewhere in TCP code)
- linebreak adjustments (readability)
- nested if()s combined (reduced indentation)
- clarifying newlines added
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The accounting code is pretty much the same, so it's a shame
we do it in two places.
I'm not too sure if added fully_acked check in MTU probing is
really what we want perhaps the added end_seq could be used in
the after() comparison.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Substraction for fackets_out is unconditional when snd_una
advances, thus there's no need to do it inside the loop. Just
make sure correct bounds are honored.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, it should not be necessary to call tcp_fragment for
already SACKed skbs, but it's better to be safe than sorry. And
indeed, it can be called from sacktag when a DSACK arrives or
some ACK (with SACK) reordering occurs (sacktag could be made
to avoid the call in the latter case though I'm not sure if it's
worth of the trouble and added complexity to cover such marginal
case).
The collapse case has return for SACKED_ACKED case earlier, so
just WARN_ON if internal inconsistency is detected for some
reason.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return some useful information such as the maximum listen backlog and
the current listen backlog in the tcp_info structure and
INET_DIAG_INFO.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I proposed introducing a list_for_each_entry_continue_reverse macro
to be used in setup_net() when unrolling the failed ->init callback.
Here is the macro and some more cleanup in the setup_net() itself
to remove one variable from the stack :) The same thing is for the
cleanup_net() - the existing list_for_each_entry_reverse() is used.
Minor, but the code looks nicer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADD-IP spec requires AUTH. It is, in fact, dangerous without AUTH.
So, disable ADD-IP functionality if the peer claims to support
ADD-IP, but not AUTH.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SCTP-AUTH API. The API implemented here was
agreed to between implementors at the 9th SCTP Interop.
It will be documented in the next revision of the
SCTP socket API spec.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the receive path needed to process authenticated
chunks. Add ability to process the AUTH chunk and handle edge cases
for authenticated COOKIE-ECHO as well.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP-AUTH, Section 6.2:
Endpoints MUST send all requested chunks authenticated where this has
been requested by the peer. The other chunks MAY be sent
authenticated or not. If endpoint pair shared keys are used, one of
them MUST be selected for authentication.
To send chunks in an authenticated way, the sender MUST include these
chunks after an AUTH chunk. This means that a sender MUST bundle
chunks in order to authenticate them.
If the endpoint has no endpoint pair shared key for the peer, it MUST
use Shared Key Identifier 0 with an empty endpoint pair shared key.
If there are multiple endpoint shared keys the sender selects one and
uses the corresponding Shared Key Identifier
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement processing for the CHUNKS, RANDOM, and HMAC parameters and
deal with how this parameters are effected by association restarts.
In particular, during unexpeted INIT processing, we need to reply with
parameters from the original INIT chunk. Also, after restart, we need
to update the old association with new peer parameters and change the
association shared keys.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch initializes AUTH related members of the generic SCTP
structures and provides a way to enable/disable auth extension.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the internals operations of the AUTH, such as
key computation and storage. It also adds necessary variables to
the SCTP data structures.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Background: RFC 4293 deprecates existing individual, named ICMP
type counters to be replaced with the ICMPMsgStatsTable. This table
includes entries for both IPv4 and IPv6, and requires counting of all
ICMP types, whether or not the machine implements the type.
These patches "remove" (but not really) the existing counters, and
replace them with the ICMPMsgStats tables for v4 and v6.
It includes the named counters in the /proc places they were, but gets the
values for them from the new tables. It also counts packets generated
from raw socket output (e.g., OutEchoes, MLD queries, RA's from
radvd, etc).
Changes:
1) create icmpmsg_statistics mib
2) create icmpv6msg_statistics mib
3) modify existing counters to use these
4) modify /proc/net/snmp to add "IcmpMsg" with all ICMP types
listed by number for easy SNMP parsing
5) modify /proc/net/snmp printing for "Icmp" to get the named data
from new counters.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Background: RFC 4293 deprecates existing individual, named ICMP
type counters to be replaced with the ICMPMsgStatsTable. This table
includes entries for both IPv4 and IPv6, and requires counting of all
ICMP types, whether or not the machine implements the type.
These patches "remove" (but not really) the existing counters, and
replace them with the ICMPMsgStats tables for v4 and v6.
It includes the named counters in the /proc places they were, but gets the
values for them from the new tables. It also counts packets generated
from raw socket output (e.g., OutEchoes, MLD queries, RA's from
radvd, etc).
Changes:
1) create icmpmsg_statistics mib
2) create icmpv6msg_statistics mib
3) modify existing counters to use these
4) modify /proc/net/snmp to add "IcmpMsg" with all ICMP types
listed by number for easy SNMP parsing
5) modify /proc/net/snmp printing for "Icmp" to get the named data
from new counters.
[new to 2nd revision]
6) support per-interface ICMP stats
7) use common macro for per-device stat macros
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with the macro max provided by <linux/kernel.h>, so changed its name
to a more proper one: limit
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks for noticing the bug where csum_start is not updated
when the head room changes.
This patch fixes that. It also moves the csum/ip_summed
copying into copy_skb_header so that skb_copy_expand gets
it too. I've checked its callers and no one should be upset
by this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was looking at Patrick's fix to inet_diag and it occured
to me that we're using a pointer argument to return values
unnecessarily in netlink_run_queue. Changing it to return
the value will allow the compiler to generate better code
since the value won't have to be memory-backed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sctp_[rw]mem definitions should really be in protocol.c
since that is where they are initialized. This also allows
one to build a kernel without sysctl support.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP Supported Extenions parameter is specified in Section 4.2.7
of the ADD-IP draft (soon to be RFC). The parameter is
encoded as:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Parameter Type = 0x8008 | Parameter Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CHUNK TYPE 1 | CHUNK TYPE 2 | CHUNK TYPE 3 | CHUNK TYPE 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CHUNK TYPE N | PAD | PAD | PAD |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
It contains a list of chunks that a particular SCTP extension
uses. Current extensions supported are Partial Reliability
(FWD-TSN) and ADD-IP (ASCONF and ASCONF-ACK).
When implementing new extensions (AUTH, PKT-DROP, etc..), new
chunks need to be added to this parameter. Parameter processing
would be modified to negotiate support for these new features.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch slightly cleanups FIB rules framework. rules_list as a pointer
on struct fib_rules_ops is useless. It is always assigned with a static
per/subsystem list in IPv4, IPv6 and DecNet.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call_netdev_notifiers routine can successfully be used in
the net/core_dev.c itself.
This will save 6 lines of code and 62 ;) bytes of .text section.
62 is rather small, but I have one more patch saving ~30 bytes
from netns code (sent to Eric), so altogether they can save
some more noticeable amount.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_name_hash and the dev_index_hash are now booth kmalloc-ed
(and each element is properly initialized as usually) so I think
it's worth consolidating this code making it look nicer (and
saving 28 bytes of .text section ;) )
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the void * parameter with a struct net_device * which
is what is actually required.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HARD_TX_LOCK micro is a nice aggregation that could be used
in other spots. move it to netdevice.h
Also makes sure the previously superflous cpu arguement is used.
Thanks to DaveM for the suggestions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove useless message. We get the right message from another
subsystem.
Signed-off-by: Milan Kocian <milon@wq.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bulk of the CIPSO option parsing/processing in the cipso_v4_sock_getattr()
and cipso_v4_skb_getattr() functions are identical, the only real difference
being where the functions obtain the CIPSO option itself. This patch creates
a new function, cipso_v4_getattr(), which contains the common CIPSO option
parsing/processing code and modifies the existing functions to call this new
helper function.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few TODO comments in the mac80211 sources regarding
hardware offload for Michael MIC verification. Those items are,
however, better handled in the driver instead of the stack, if
any device requires such hand-holding.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx.mode must be set also for buffered frames. It is used in the tx hanlders
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats are now available for device usage inside network_device
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg noticed that in __ieee80211_tx_prepare() we try to get the
STA from addr1 of the ieee80211 header when the radiotap header is actually
still at the front of the packet. This patch defers doing that until the
radiotap header is gone.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work-around for broken APs that use a non-zero key index for WEP
pairwise keys. With this patch, WEP encryption only is exempt from
providing a zero key index.
Signed-off-by: Volker Braun <volker.braun@physik.hu-berlin.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TKIP mixing code was added for the benefit of Intel's ipw3945
chipset but that code ended up not using it. We have previously
identified many problems with this code and it crystallized that
library functions for mixing are likely to handle this in much
more generality and might allow b43 to take advantage of hardware
acceleration for TKIP.
Due to these reasons, remove the TKIP mixing for hardware
accelerated crypto operations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the mac80211/driver interface rely only on the
IEEE80211_TXCTL_DO_NOT_ENCRYPT flag to signal to the driver whether
a frame should be encrypted or not, since mac80211 internally no
longer relies on HW_KEY_IDX_INVALID either this removes it, changes
the key index to be a u8 in all places and makes the full range of
the value available to drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No existing drivers use this callback, hence there's no telling
how it might be used. In fact, it is unlikely to be of much use
as-is because the default key index isn't something that the
driver can do much with without knowing which interface it was
for etc. And if it needs the key index for the transmitted frame,
it can get it by keeping a reference to the key_conf structure
and looking it up by hw_key_idx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the various hardware crypto related
flags to make them more local, i.e. put them with each
key or each packet instead of into the hw struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all mention of the atheros turbo modes that
can't possibly work properly anyway since in some places we don't
check for them when we should.
I have no idea what the iwlwifi drivers were doing with these but
it can't possibly have been correct.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During receive processing, we select the key long before using it and
because there's no locking it is possible that we kfree() the key
after having selected it but before using it for crypto operations.
Obviously, this is bad.
Secondly, during transmit processing, there are two possible races: We
have a similar race between select_key() and using it for encryption,
but we also have a race here between select_key() and hardware
encryption (both when a key is removed.)
This patch solves these issues by using RCU: when a key is to be freed,
we first remove the pointer from the appropriate places (sdata->keys,
sdata->default_key, sta->key) using rcu_assign_pointer() and then
synchronize_rcu(). Then, we can safely kfree() the key and remove it
from the hardware. There's a window here where the hardware may still
be using it for decryption, but we can't work around that without having
two hardware callbacks, one to disable the key for RX and one to disable
it for TX; but the worst thing that will happen is that we receive a
packet decrypted that we don't find a key for any more and then drop it.
When we add a key, we first need to upload it to the hardware and then,
using rcu_assign_pointer() again, link it into our structures.
In the code using keys (TX/RX paths) we use rcu_dereference() to get the
key and enclose the whole tx/rx section in a rcu_read_lock() ...
rcu_read_unlock() block. Because we've uploaded the key to hardware
before linking it into internal structures, we can guarantee that it is
valid once get to into tx().
One possible race condition remains, however: when we have hardware
acceleration enabled and the driver shuts down the queues, we end up
queueing the frame. If now somebody removes the key, the key will be
removed from hwaccel and then then driver will be asked to encrypt the
frame with a key index that has been removed. Hence, drivers will need
to be aware that the hw_key_index they are passed might not be under
all circumstances. Most drivers will, however, simply ignore that
condition and encrypt the frame with the selected key anyway, this
only results in a frame being encrypted with a wrong key or dropped
(rightfully) because the key was not valid. There isn't much we can
do about it unless we want to walk the pending frame queue every time
a key is removed and remove all frames that used it.
This race condition, however, will most likely be solved once we add
multiqueue support to mac80211 because then frames will be queued
further up the stack instead of after being processed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo noticed that QoS frames are sent with an invalid QoS control
field; this is because we increase the header length but neither
initialise the space nor actually have enough space in the header
structure for the QoS control field.
This patch fixes it by treating the QoS field specially and appending it
explicitly, initialising it to zero.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 never calls wireless_spy_update so these aren't
useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On loaded/big hosts, rt_check_expire() if of litle use, because it
generally breaks out of its main loop because of a jiffies change.
It can take a long time (read : timer invocations) to actually
scan the whole hash table, freeing unused entries.
Converting it to use a workqueue instead of softirq is a nice
move because we can allow rt_check_expire() to do the scan
it is supposed to do, without hogging the CPU.
This has an impact on the average number of entries in cache,
reducing ram usage. Cache is more responsive to parameter
changes (/proc/sys/net/ipv4/route/gc_timeout and
/proc/sys/net/ipv4/route/gc_interval)
Note: Maybe the default value of gc_interval (60 seconds)
is too high, since this means we actually need 5 (300/60)
invocations to scan the whole table.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for UWB keys to rfkill,
support for this has been requested by Inaky.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Dmitry pointed out earlier, rfkill-input.c
doesn't support irda because there are no users
and we shouldn't add unrequired KEY_ defines.
However, RFKILL_TYPE_IRDA was defined in the
rfkill.h header file and would confuse people
about whether it is implemented or not.
This patch removes IRDA support completely,
so it can be added whenever a driver wants the
feature.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem: proc_net files remember which network namespace the are
against but do not remember hold a reference count (as that would pin
the network namespace). So we currently have a small window where
the reference count on a network namespace may be incremented when opening
a /proc file when it has already gone to zero.
To fix this introduce maybe_get_net and get_proc_net.
maybe_get_net increments the network namespace reference count only if it is
greater then zero, ensuring we don't increment a reference count after it
has gone to zero.
get_proc_net handles all of the magic to go from a proc inode to the network
namespace instance and call maybe_get_net on it.
PROC_NET the old accessor is removed so that we don't get confused and use
the wrong helper function.
Then I fix up the callers to use get_proc_net and handle the case case
where get_proc_net returns NULL. In that case I return -ENXIO because
effectively the network namespace has already gone away so the files
we are trying to access don't exist anymore.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change L2T (length to time) macros, in all rate based schedulers, to
call a common function qdisc_l2t() that does the rate table lookup.
This function handles if the packet size lookup is larger than the
rate table, which often occurs with TSO enabled.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the following needlessly global variables static:
- sctp_memory_pressure
- sctp_memory_allocated
- sctp_sockets_allocated
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the generic attribute interface to be used within
the netfilter subsystem where this flag was initially introduced.
The byte-order flag is yet unused, it's intended use is to
allow automatic byte order convertions for all atomic types.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the periodic IP route cache flush is done (every 600 seconds on
default configuration), some hosts suffer a lot and eventually trigger
the "soft lockup" message.
dst_run_gc() is doing a scan of a possibly huge list of dst_entries,
eventually freeing some (less than 1%) of them, while holding the
dst_lock spinlock for the whole scan.
Then it rearms a timer to redo the full thing 1/10 s later...
The slowdown can last one minute or so, depending on how active are
the tcp sessions.
This second version of the patch converts the processing from a softirq
based one to a workqueue.
Even if the list of entries in garbage_list is huge, host is still
responsive to softirqs and can make progress.
Instead of resetting gc timer to 0.1 second if one entry was freed in a
gc run, we do this if more than 10% of entries were freed.
Before patch :
Aug 16 06:21:37 SRV1 kernel: BUG: soft lockup detected on CPU#0!
Aug 16 06:21:37 SRV1 kernel:
Aug 16 06:21:37 SRV1 kernel: Call Trace:
Aug 16 06:21:37 SRV1 kernel: <IRQ> [<ffffffff802286f0>] wake_up_process+0x10/0x20
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80251e09>] softlockup_tick+0xe9/0x110
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803cd380>] dst_run_gc+0x0/0x140
Aug 16 06:21:37 SRV1 kernel: [<ffffffff802376f3>] run_local_timers+0x13/0x20
Aug 16 06:21:37 SRV1 kernel: [<ffffffff802379c7>] update_process_times+0x57/0x90
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80216034>] smp_local_timer_interrupt+0x34/0x60
Aug 16 06:21:37 SRV1 kernel: [<ffffffff802165cc>] smp_apic_timer_interrupt+0x5c/0x80
Aug 16 06:21:37 SRV1 kernel: [<ffffffff8020a816>] apic_timer_interrupt+0x66/0x70
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803cd3d3>] dst_run_gc+0x53/0x140
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803cd3c6>] dst_run_gc+0x46/0x140
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80237148>] run_timer_softirq+0x148/0x1c0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff8023340c>] __do_softirq+0x6c/0xe0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff8020ad6c>] call_softirq+0x1c/0x30
Aug 16 06:21:37 SRV1 kernel: <EOI> [<ffffffff8020cb34>] do_softirq+0x34/0x90
Aug 16 06:21:37 SRV1 kernel: [<ffffffff802331cf>] local_bh_enable_ip+0x3f/0x60
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80422913>] _spin_unlock_bh+0x13/0x20
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803dfde8>] rt_garbage_collect+0x1d8/0x320
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803cd4dd>] dst_alloc+0x1d/0xa0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803e1433>] __ip_route_output_key+0x573/0x800
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803c02e2>] sock_common_recvmsg+0x32/0x50
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803e16dc>] ip_route_output_flow+0x1c/0x60
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80400160>] tcp_v4_connect+0x150/0x610
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803ebf07>] inet_bind_bucket_create+0x17/0x60
Aug 16 06:21:37 SRV1 kernel: [<ffffffff8040cd16>] inet_stream_connect+0xa6/0x2c0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80422981>] _spin_lock_bh+0x11/0x30
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803c0bdf>] lock_sock_nested+0xcf/0xe0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80422981>] _spin_lock_bh+0x11/0x30
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803be551>] sys_connect+0x71/0xa0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803eee3f>] tcp_setsockopt+0x1f/0x30
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803c030f>] sock_common_setsockopt+0xf/0x20
Aug 16 06:21:37 SRV1 kernel: [<ffffffff803be4bd>] sys_setsockopt+0x9d/0xc0
Aug 16 06:21:37 SRV1 kernel: [<ffffffff8028881e>] sys_ioctl+0x5e/0x80
Aug 16 06:21:37 SRV1 kernel: [<ffffffff80209c4e>] system_call+0x7e/0x83
After patch : (RT_CACHE_DEBUG set to 2 to get following traces)
dst_total: 75469 delayed: 74109 work_perf: 141 expires: 150 elapsed: 8092 us
dst_total: 78725 delayed: 73366 work_perf: 743 expires: 400 elapsed: 8542 us
dst_total: 86126 delayed: 71844 work_perf: 1522 expires: 775 elapsed: 8849 us
dst_total: 100173 delayed: 68791 work_perf: 3053 expires: 1256 elapsed: 9748 us
dst_total: 121798 delayed: 64711 work_perf: 4080 expires: 1997 elapsed: 10146 us
dst_total: 154522 delayed: 58316 work_perf: 6395 expires: 25 elapsed: 11402 us
dst_total: 154957 delayed: 58252 work_perf: 64 expires: 150 elapsed: 6148 us
dst_total: 157377 delayed: 57843 work_perf: 409 expires: 400 elapsed: 6350 us
dst_total: 163745 delayed: 56679 work_perf: 1164 expires: 775 elapsed: 7051 us
dst_total: 176577 delayed: 53965 work_perf: 2714 expires: 1389 elapsed: 8120 us
dst_total: 198993 delayed: 49627 work_perf: 4338 expires: 1997 elapsed: 8909 us
dst_total: 226638 delayed: 46865 work_perf: 2762 expires: 2748 elapsed: 7351 us
I successfully reduced the IP route cache of many hosts by a four factor
thanks to this patch. Previously, I had to disable "ip route flush cache"
to avoid crashes.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until we support multiple network namespaces with netfilter only allow
netfilter configuration in the initial network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The simplest thing to implement is moving network devices between
namespaces. However with the same attribute IFLA_NET_NS_PID we can
easily implement creating devices in the destination network
namespace as well. However that is a little bit trickier so this
patch sticks to what is simple and easy.
A pid is used to identify a process that happens to be a member
of the network namespace we want to move the network device to.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces NETIF_F_NETNS_LOCAL a flag to indicate
a network device is local to a single network namespace and
should never be moved. Useful for pseudo devices that we
need an instance in each network namespace (like the loopback
device) and for any device we find that cannot handle multiple
network namespaces so we may trap them in the initial network
namespace.
This patch introduces the function dev_change_net_namespace
a function used to move a network device from one network
namespace to another. To the network device nothing
special appears to happen, to the components of the network
stack it appears as if the network device was unregistered
in the network namespace it is in, and a new device
was registered in the network namespace the device
was moved to.
This patch sets up a namespace device destructor that
upon the exit of a network namespace moves all of the
movable network devices to the initial network namespace
so they are not lost.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcibly changing the network namespace of a device
I need something that can generate a name for the device
in the new namespace without overwriting the old name.
__dev_alloc_name provides me that functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each netlink socket will live in exactly one network namespace,
this includes the controlling kernel sockets.
This patch updates all of the existing netlink protocols
to only support the initial network namespace. Request
by clients in other namespaces will get -ECONREFUSED.
As they would if the kernel did not have the support for
that netlink protocol compiled in.
As each netlink protocol is updated to be multiple network
namespace safe it can register multiple kernel sockets
to acquire a presence in the rest of the network namespaces.
The implementation in af_netlink is a simple filter implementation
at hash table insertion and hash table look up time.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every user of the network device notifiers is either a protocol
stack or a pseudo device. If a protocol stack that does not have
support for multiple network namespaces receives an event for a
device that is not in the initial network namespace it quite possibly
can get confused and do the wrong thing.
To avoid problems until all of the protocol stacks are converted
this patch modifies all netdev event handlers to ignore events on
devices that are not in the initial network namespace.
As the rest of the code is made network namespace aware these
checks can be removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies every packet receive function
registered with dev_add_pack() to drop packets if they
are not from the initial network namespace.
This should ensure that the various network stacks do
not receive packets in a anything but the initial network
namespace until the code has been converted and is ready
for them.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for carefully selected pseudo devices all network
interfaces should start out in the initial network namespace.
Ultimately it will be register_netdev that examines what
dev->nd_net is set to and places a device in a network namespace.
This patch modifies alloc_netdev to initialize the network
namespace a device is in with the initial network namespace.
This gets it right for the vast majority of devices so their
drivers need not be modified and for those few pseudo devices
that need something different they can change this parameter
before calling register_netdevice.
The network namespace parameter on a network device is not
reference counted as the devices are inside of a network namespace
and cannot remain in that namespace past the lifetime of the
network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch passes in the namespace a new socket should be created in
and has the socket code do the appropriate reference counting. By
virtue of this all socket create methods are touched. In addition
the socket create methods are modified so that they will fail if
you attempt to create a socket in a non-default network namespace.
Failing if we attempt to create a socket outside of the default
network namespace ensures that as we incrementally make the network stack
network namespace aware we will not export functionality that someone
has not audited and made certain is network namespace safe.
Allowing us to partially enable network namespaces before all of the
exotic protocols are supported.
Any protocol layers I have missed will fail to compile because I now
pass an extra parameter into the socket creation code.
[ Integrated AF_IUCV build fixes from Andrew Morton... -DaveM ]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes /proc/net per network namespace. It modifies the global
variables proc_net and proc_net_stat to be per network namespace.
The proc_net file helpers are modified to take a network namespace argument,
and all of their callers are fixed to pass &init_net for that argument.
This ensures that all of the /proc/net files are only visible and
usable in the initial network namespace until the code behind them
has been updated to be handle multiple network namespaces.
Making /proc/net per namespace is necessary as at least some files
in /proc/net depend upon the set of network devices which is per
network namespace, and even more files in /proc/net have contents
that are relevant to a single network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the basic infrastructure needed to support network
namespaces. This infrastructure is:
- Registration functions to support initializing per network
namespace data when a network namespaces is created or destroyed.
- struct net. The network namespace data structure.
This structure will grow as variables are made per network
namespace but this is the minimal starting point.
- Functions to grab a reference to the network namespace.
I provide both get/put functions that keep a network namespace
from being freed. And hold/release functions serve as weak references
and will warn if their count is not zero when the data structure
is freed. Useful for dealing with more complicated data structures
like the ipv4 route cache.
- A list of all of the network namespaces so we can iterate over them.
- A slab for the network namespace data structure allowing leaks
to be spotted.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This slightly improves code safety and clarity.
Later network namespace patches touch this code so this is a
preliminary cleanup.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the current ipsec audit layer
by breaking it up into purpose driven audit calls.
So far, the only audit calls made are when add/delete
an SA/policy. It had been discussed to give each
key manager it's own calls to do this, but I found
there to be much redundnacy since they did the exact
same things, except for how they got auid and sid, so I
combined them. The below audit calls can be made by any
key manager. Hopefully, this is ok.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of owner in sock_lock_t is currently (struct sock_iocb *),
presumably for historical reasons. It is never used as this type, only
tested as NULL or set to (void *)1. For clarity, this changes it to type
int, and renames to owned, to avoid any possible type casting errors.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes asserts in sunrpc to use sock_owned_by_user() macro instead of
referencing sock_lock.owner directly.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andi mentioned he did something like this already, but never submitted
it.
The dhcp client application uses AF_PACKET with a packet filter to
receive data. The application doesn't even use timestamps, but because
the AF_PACKET API has timestamps, they get turned on globally which
causes an expensive time of day lookup for every packet received on
any system that uses the standard DHCP client.
The fix is to not enable the timestamp (but use if if available).
This causes the time lookup to only occur on those packets that are
destined for the AF_PACKET socket. The timestamping occurs after
packet filtering so all packets dropped by filtering to not cause a
clock call.
The one downside of this a a few microseconds additional delay added
from the normal timestamping location (netif_rx) until the receive
callback in AF_PACKET. But since the offset is fairly consistent it
should not upset applications that do want really use timestamps, like
wireshark.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial patch removes the unneeded pointer newdp, which is never used.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial patch removes the unneeded pointer iph, which is never used.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sta_info.assoc_ap value is used as a flag, move it
into flags.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes some definitions that are used only within ioctls
that will never make it into mainline.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I changed the code there I forgot to mention what happens
with multicast frames in a regular BSS and keep wondering myself
if the code is correct. Add appropriate comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In STA mode, the AP will echo our traffic. This includes multicast
traffic.
Receiving these frames confuses some protocols and applications,
notably IPv6 Duplicate Address Detection.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up some whitespace to make the mac80211
version in mainline diverge less from wireless-dev.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like in commit 28487a90 the condition was unintentionally
negated by moving some code, fix it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Drake <dsd@gentoo.org>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current version of wireless statistics contains a bug in the averaging
that makes the numbers be too sticky and not react to small changes. This
patch removes all averaging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new file 'ifindex' to each key's debugfs dir to
allow finding which interface the key was configured on.
This isn't done as a symlink because of possible netdev
name changes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves all the key handling code out from ieee80211_ioctl.c
into key.c and also does the following changes including documentation
updates in mac80211.h:
1) Turn off hardware acceleration for keys when the interface
is down. This is necessary because otherwise monitor
interfaces could be decrypting frames for other interfaces
that are down at the moment. Also, it should go some way
towards better suspend/resume support, in any case the
routines used here could be used for that as well.
Additionally, this makes the driver interface nicer, keys
for a specific local MAC address are only ever present
while an interface with that MAC address is enabled.
2) Change driver set_key() callback interface to allow only
return values of -ENOSPC, -EOPNOTSUPP and 0, warn on all
other return values. This allows debugging the stack when
a driver notices it's handed a key while it is down.
3) Invert the flag meaning to KEY_FLAG_UPLOADED_TO_HARDWARE.
4) Remove REMOVE_ALL_KEYS command as it isn't used nor do we
want to use it, we'll use DISABLE_KEY for each key. It is
hard to use REMOVE_ALL_KEYS because we can handle multiple
virtual interfaces with different key configuration, so we'd
have to keep track of a lot of state for this and that isn't
worth it.
5) Warn when disabling a key fails, it musn't.
6) Remove IEEE80211_HW_NO_TKIP_WMM_HWACCEL in favour of per-key
IEEE80211_KEY_FLAG_WMM_STA to let driver sort it out itself.
7) Tell driver that a (non-WEP) key is used only for transmission
by using an all-zeroes station MAC address when configuring.
8) Change the set_key() callback to have access to the local MAC
address the key is being added for.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove adding a fake key with a NONE key algorithm for each
associated STA. If we have hardware with such TX filtering
we should probably extend the sta_table_notification()
callback with the sta information instead; the fact that
it's treated as a key for some atheros hardware shouldn't
bother the stack.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the default_wep_only stuff, this wasn't really done well
and no current driver actually cares.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
they aren't really refcounted anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch embeds the struct ieee80211_key_conf into struct ieee80211_key
and thus avoids allocations and having data present twice.
This required some more changes:
1) The removal of the IEEE80211_KEY_DEFAULT_TX_KEY key flag.
This flag isn't used by drivers nor should it be since
we have a set_key_idx() callback. Maybe that callback needs
to be extended to include the key conf, but only a driver that
requires it will tell.
2) The removal of the IEEE80211_KEY_DEFAULT_WEP_ONLY key flag.
This flag is global, so it shouldn't be passed in the key
conf structure. Pass it to the function instead.
Also, this patch removes the AID parameter to the set_key() callback
because it is currently unused and the hardware currently cannot know
about the AID anyway. I suspect this was used with some hardware that
actually selected the AID itself, but that functionality was removed.
Additionally, I've removed the ALG_NULL key algorithm since we have
ALG_NONE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_sub_if_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_if_sta
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211, remove bitfields from struct ieee80211_txrx_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove bitfields from struct ieee80211_tx_packet_data
[Johannes: completely clear flags in ieee80211_remove_tx_extra]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transmit code needs to set the addresses depending on the
interface type, a likely() for AP/VLAN is quite wrong since
most people will be using STA; convert to a switch statement
to make it look nicer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new file event.c that will contain code to send mac/mlme
events to userspace. For now put the Michael MIC failure condition
into it and remove sending of that condition via the management
interface, hostapd interestingly doesn't do anything when it gets
such a packet besides printing a message, it reacts only on the
private iwevent.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The key_mgmt variable for STA interfaces doesn't seem well-defined
nor do we actually use the values other than "NONE", so change it to
be named better.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_RADAR_DETECT
* PRISM2_PARAM_SPECTRUM_MGMT
are not used by hostapd or wpa_supplicant,
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_STA_ANTENNA_SEL
* PRISM2_PARAM_TX_POWER_REDUCTION
* PRISM2_PARAM_DEFAULT_WEP_ONLY
are not used by hostapd or wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ioctls
* PRISM2_PARAM_ANTENNA_MODE
* PRISM2_PARAM_STAT_TIME
are not used by hostapd or wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing key selection for software decryption, mac80211 gets
a few things wrong: it always uses pairwise keys if configured,
even if the frame is addressed to a multicast address. Also, it
doesn't allow using a key index of zero if a pairwise key has
also been found.
This patch changes the key selection code to be (more) in line
with the 802.11 specification. I have confirmed that with this,
multicast frames are correctly decrypted and I've tested with
WEP as well.
While at it, I've cleaned up the semantics of the hardware flags
IEEE80211_HW_WEP_INCLUDE_IV and IEEE80211_HW_DEVICE_HIDES_WEP
and clarified them in the mac80211.h header; it is also now
allowed to set the IEEE80211_HW_DEVICE_HIDES_WEP option even if
it only applies to frames that have been decrypted by the hw,
unencrypted frames must be dropped but encrypted frames that
the hardware couldn't handle can be passed up unmodified.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unused in drivers, userspace and mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither hostapd nor wpa_supplicant really use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many if not all of these messages can be triggered by sending
a few rogue frames which is trivially done and then we overflow
our logs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This now is unused in hostapd/wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two issues with the key debugfs:
1) key index obviously isn't unique
2) various missing break statements led to bogus output
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse noticed that under some circumstances the number of slab
allocations kept growing. After looking a bit, this seemed to happen
when you had a management mode interface that was *down*.
The reason for this is that when the device is down, all management
frames get queued to the in-kernel MLME (via ieee80211_sta_rx_mgmt) but
then the sta work is invoked but doesn't run when the netif is down.
When you then bring the interface up, all such frames are freed, but if
you change the mode all of them are lost because the skb queue is
reinitialised as soon as you go back to managed mode. The skb queue is
correctly cleared when the interface is brought down, but the code
doesn't account for the fact that it may be filled while it is not up.
This patch should fix the issue by simply ignoring all interfaces that
are down when going through the RX handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully captured all single statement cases under net/. I'm
not too sure if there is some policy about #includes that are
"guaranteed" (ie., in the current tree) to be available through
some other #included header, so I just added linux/kernel.h to
each changed file that didn't #include it previously.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below some pktgen support to send into different TX queues.
This can of course be feed into input queues on other machines
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This could make future redesign of struct netlink_sock easier.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 IPsec tunnel gateway incorrectly sends redirect to
sender if it is onlink host when network device the IPsec tunnelled
packet is arrived is the same as the one the decapsulated packet
is sent.
With this patch, it omits to send the redirect when the forwarding
skbuff carries secpath, since such skbuff should be assumed as
a decapsulated packet from IPsec tunnel by own.
Request for comments:
Alternatively we'd have another way to change net/ipv4/route.c
(__mkroute_input) to use RTCF_DOREDIRECT flag unless skbuff
has no secpath. It is better than this patch at performance
point of view because IPv4 redirect judgement is done at
routing slow-path. However, it should be taken care of resource
changes between SAD(XFRM states) and routing table. In other words,
When IPv4 SAD is changed does the related routing entry go to its
slow-path? If not, it is reasonable to apply this patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 IPsec tunnel gateway incorrectly sends redirect to
router or sender when network device the IPsec tunnelled packet
is arrived is the same as the one the decapsulated packet
is sent.
With this patch, it omits to send the redirect when the forwarding
skbuff carries secpath, since such skbuff should be assumed as
a decapsulated packet from IPsec tunnel by own.
It may be a rare case for an IPsec security gateway, however
it is not rare when the gateway is MIPv6 Home Agent since
the another tunnel end-point is Mobile Node and it changes
the attached network.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When XFRM policy and state are ready after TCP connection is started,
the traffic should be transformed immediately, however it does not
on IPv6 TCP.
It depends on a dst cache replacement policy with connected socket.
It seems that the replacement is always done for IPv4, however, on
IPv6 case it is done only when routing cookie is changed.
This patch fix that non-transformation dst can be changed to
transformation one.
This behavior is required by MIPv6 and improves IPv6 IPsec.
Fixes by Masahide NAKAMURA.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add v4mapped address inline to avoid calls to ipv6_addr_type().
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch causes UDP port allocation to be randomized like TCP.
The earlier code would always choose same port (ie first empty list).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DSACK case, some events are not extraordinary, such as packet
duplication generated DSACK. They can arrive easily below
snd_una when undo_marker is not set (TCP being in CA_Open),
counting such DSACKs amoung SACK discards will likely just
mislead if they occur in some scenario when there are other
problems as well. Similarly, excessively delayed packets could
cause "normal" DSACKs. Therefore, separate counters are
allocated for DSACK events.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
SACK processing code has been a sort of russian roulette as no
validation of SACK blocks is previously attempted. Besides, it
is not very clear what all kinds of broken SACK blocks really
mean (e.g., one that has start and end sequence numbers
reversed). So now close the roulette once and for all.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only thing that tiny function does is rearming the RTO (if
necessary), name it accordingly.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes caller side more obvious, there's no need to have
a wrapper for this oneliner!
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of using DPRINTK macro in ATM and use pr_debug (in kernel.h).
Using the standard macro is cleaner and forces code to check for bad arguments
and formatting.
Fixes from Thomas Graf.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet header management only needs to handle a fixed
size address (6 bytes). If the memcpy/memset are changed to
be passed a constant length, then compiler can optimize for
this case (and if it is smart eliminate string instructions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are only used once and are a lot easier to understand if
inlined directly into the function.
Fixes by Masahide NAKAMURA.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlmsg_parse() puts attributes at array[type] so the indexing
method can be simpilfied by removing the obscuring "- 1".
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a policy defining the minimal payload lengths for all the attributes
allowing for most attribute validation checks to be removed from in
the middle of the code path. Makes updates more consistent as many format
errors are recognised earlier, before any changes have been attempted.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uses nlmsg_parse() to parse the attributes. This actually changes
behaviour as unknown attributes (type > MAXTYPE) no longer cause
an error. Instead unknown attributes will be ignored henceforth
to keep older kernels compatible with more recent userspace tools.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves all complex message size calculation into own inlined helper
functions and makes use of the type-safe netlink interface.
Using nlmsg_new() simplifies the calculation itself as it takes care
of the netlink header length by itself.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves all of the SUB_POLICY ifdefs related to the attribute size
calculation into a function.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds alg_len() to calculate the properly padded length of an
algorithm attribute to simplify the code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also makes use of copy_sec_ctx() in another place and removes
duplicated code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now to convert the ackvec code to ktime_t so that we can get rid of
dccp_timestamp and the epoch thing in dccp_sock.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was too complicated, if p > 0 in ccid3_hc_tx_no_feedback_timer the
timestamp was being obtained to be passed to ccid3_hc_tx_update_x, where only
if p > 0 the timestamp was needed, so just leave it to ccid3_hc_tx_update_x to
obtain the timestamp if needed.
This will help in the upcoming changesets where we'll convert t_ld to ktime_t.
We'll eventually try to reuse ktime_get_real() calls again.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces autotuning to the sctp buffer management code
similar to the TCP. The buffer space can be grown if the advertised
receive window still has room. This might happen if small message
sizes are used, which is common in telecom environmens.
New tunables are introduced that provide limits to buffer growth
and memory pressure is entered if to much buffer spaces is used.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several get/set functions can be handled by a passing the ethtool_op
function pointer directly to a generic function. This permits deletion
of a fair bit of redundant code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
This patch introduces support for dynamic reconfiguration (adding, removing
and/or modifying parameters of netconsole targets at runtime) using a
userspace interface exported via configfs. Documentation is also updated
accordingly.
Issues and brief design overview:
(1) Kernel-initiated creation / destruction of kernel objects is not
possible with configfs -- the lifetimes of the "config items" is managed
exclusively from userspace. But netconsole must support boot/module
params too, and these are parsed in kernel and hence netpolls must be
setup from the kernel. Joel Becker suggested to separately manage the
lifetimes of the two kinds of netconsole_target objects -- those created
via configfs mkdir(2) from userspace and those specified from the
boot/module option string. This adds complexity and some redundancy here
and also means that boot/module param-created targets are not exposed
through the configfs namespace (and hence cannot be updated / destroyed
dynamically). However, this saves us from locking / refcounting
complexities that would need to be introduced in configfs to support
kernel-initiated item creation / destroy there.
(2) In configfs, item creation takes place in the call chain of the
mkdir(2) syscall in the driver subsystem. If we used an ioctl(2) to
create / destroy objects from userspace, the special userspace program is
able to fill out the structure to be passed into the ioctl and hence
specify attributes such as local interface that are required at the time
we set up the netpoll. For configfs, this information is not available at
the time of mkdir(2). So, we keep all newly-created targets (via
configfs) disabled by default. The user is expected to set various
attributes appropriately (including the local network interface if
required) and then write(2) "1" to the "enabled" attribute. Thus,
netpoll_setup() is then called on the set parameters in the context of
_this_ write(2) on the "enabled" attribute itself. This design enables
the user to reconfigure existing netconsole targets at runtime to be
attached to newly-come-up interfaces that may not have existed when
netconsole was loaded or when the targets were actually created. All this
effectively enables us to get rid of custom ioctls.
(3) Ultra-paranoid configfs attribute show() and store() operations, with
sanity and input range checking, using only safe string primitives, and
compliant with the recommendations in Documentation/filesystems/sysfs.txt.
(4) A new function netpoll_print_options() is created in the netpoll API,
that just prints out the configured parameters for a netpoll structure.
netpoll_parse_options() is modified to use that and it is also exported to
be used from netconsole.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the messy macro for MASK_PFX to inline function
and expands TKEY_GET_MASK in the one place it is used.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try this out:
* replace macro's with inlines
* get rid of places doing multiple evaluations of NODE_PARENT
[akpm@linux-foundation.org: rcu_dereference wants an lval]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
