Remove unneeded 'struct davinci_clk' wrapper around 'struct clk_lookup'
and use clkdev_add_table() to add the list of clocks in one go.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When supporting I2C/SPI based on-board PLLs like CDCE949,
it is essential that clk->set_rate be able to sleep.
Currently, this is not possible because clk->set_rate is
called from within spin-lock in clk_set_rate
This patch brings clk->set_rate outside of the spin-lock
and lets the individual set_rate implementations achieve
serialization through appropiate means.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some modules do not have PSC to control their clocks.
The 'lpsc' field in the clk structure is 0 for such clocks.
In the clock disable function check for CLK PSC flag before
disabling the PSC. If this is not taken care of then it may
so happen that module controlled by LPSC 0 is erroneously disabled.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move /proc/davinci_clocks to /sys/kernel/debug/davinci_clocks
(debugfs).
debugfs is more suited for this since the clock dump is
debug information.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies clock dump to take care of
clock tress rooted at multiple oscillators.
Current code assumes the entire tree is rooted
on a single oscillator. When using off-chip
clock synthesizers, some of the clocks can
be obtained from a different on-board oscillator.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
As suspend support is added, the code supporting
the suspend operation needs to bypass PLLs and
needs to access the same wait time values as the
PLL code in clock.c.
To facilitate this, move the PLL wait times to
clock.h where they can be accessed by suspend code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Replace badly chosen 'psc_ctlr' name of the 'struct clk' field (PSC already
means "Power and Sleep Controller", so the '_ctlr' postfix makes the name
tautological) with technically correct 'gpsc' (Global PSC -- which contains
all the module registers).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The clk_set_parent() API is implemented to enable re-parenting
clocks in the clock tree.
This is useful in DVFS and helps by shifting clocks to an asynchronous
domain where supported by hardware
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
clk_round_rate, clk_set_rate have been updated to handle dynamic
frequency changes.
The motivation behind the changes is to support dynamic CPU frequency
change.
davinci_set_pllrate() changes the PLL rate of a given PLL. This function
has been presented as a generic function though it has been tested only
on OMAP-L138 EVM. No other currently available DaVinci device will probably
use this function, but any future device specific changes will hopefully be
small enough to get taken care using a cpu_is_xxx() macro.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Make clock rate recalculation easy by having a re-calculate
function for each clock.
The existing functions for calculation of output rates of PLL
and PLL-derived sysclks have been convered to the new
re-calculate API.
A new function is introduced to take care of rate
(re)calculation for leaf clocks.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Achieve easy top down traversal of clock tree by keeping
track of each clock's list of children.
This is useful in supporting DVFS where clock rates of
all children need to be updated in an efficient manner.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds base support for new TI SOC DM365, which s
similar to the dm355.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current code to support the DaVinci Power and Sleep Controller (PSC)
assumes that there is only one controller. This assumption is no longer
valid so expand the support to allow greater than one PSC.
To accomplish this, put the base addresses for the PSCs in the SoC
infrastructure so it can be referenced by the PSC code. This also
requires adding an extra parameter to davinci_psc_config() to specify
the PSC that is to be enabled/disabled.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is a significant rework of the low-level clock, PLL and Power
Sleep Controller (PSC) implementation for the DaVinci family. The
primary goal is to have better modeling if the hardware clocks and
features with the aim of DVFS functionality.
Highlights:
- model PLLs and all PLL-derived clocks
- model parent/child relationships of PLLs and clocks
- convert to new clkdev layer
- view clock frequency and refcount via /proc/davinci_clocks
Special thanks to significant contributions and testing by David
Brownell.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support clock control driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
