The megasky 580 based on gl861 has three endpoints:
- 0x81 BULK/ISOC IN MPEG2 TS
- 0x83 INT IN remote control receiver
- 0x02 BULK OUT bulk control endpoint
It doesn't look like the bulk endpoint is used, but better to
have the correct one in the config.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the DVB_USB_IS_AN_I2C_ADAPTER flag from the adapter
properties to the device properties.
Without this patch I get an OOPS when the gl861 driver tries to
access any registers.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gl861_tuner_attach function is not specific to this device.
This patch removes gl861_tuner_attach, and replaces it with
qt1010_tuner_attach from the qt1010 header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename driver_name from "gl861" to "dvb_usb_gl861"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The author's email address is already in the MODULE_AUTHOR field.
This patch adds his name as well.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0
Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs
to be changed. If I read the code correctly setting parallel_ts will
take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead
of 0x03 too. I guess these changes needs to be done only for this
device, not sure how to do that.
The zl10353 changes have been split apart from this patch, into the next
patch, soon to follow.
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the descriptions of "discovered" registers on the zl10353, using the
equivalaent mt352 register names.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement trl nominal rate calculation to Zarlink ZL10353 demod,
based on calculation used in Zarlink MT352.
This adds support for 6 and 8MHz bandwidth transponders.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement I2C gate control for Megasky GL861 and SigmaTek AU6610 support.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After studying many hours worth of register dumps of MT352 and ZL10353 fed
with identically damaged RF signals I have made an educated guess at which
registers contain the AGC level, bit error rate and uncorrectable error
count values.
Implement the IOCTLs that return these values to userspace.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver previously rejected encoder firmware whose size was
not a multiple of 8192. But this is a false check because it's
possible to find cx23416 firmware whose size doesn't conform to this
limit. So change the firmware loader implementation to be more
forgiving of the image size.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
avoid double-up(), pointed out by Oliver.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb kernel_thread to kthread API port.
It is running fine here, including module load/unload and software suspend
(which doesn't work as expected with or without this patch :).
I didn't convert the dvb_ca_en50221 as I do not have such an interface, but
if the conversion process is fine with the v4l-dvb maintainers, it should not
be a problem to send a patch for that too ...
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- usb alternate selection modified to get the biggest endpoint packet size.
- fix sysfs get values for brightness/contrast/hue/saturation
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes the unused struct radionorms.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
m68k allmodconfig:
drivers/media/video/video-buf.c: In function 'videobuf_queue_pci':
drivers/media/video/video-buf.c:396: error: 'pci_map_sg' undeclared (first use in this function)
drivers/media/video/video-buf.c:396: error: (Each undeclared identifier is reported only once
drivers/media/video/video-buf.c:396: error: for each function it appears in.)
drivers/media/video/video-buf.c:399: error: 'pci_dma_sync_sg_for_cpu' undeclared (first use in this function)
drivers/media/video/video-buf.c:401: error: 'pci_unmap_sg' undeclared (first use in this function)
drivers/media/video/video-buf.c: In function 'videobuf_pci_dma_map':
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes four needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed problem reported by Teemu Suikki:
After a device with subsystem 0x13c2:0x1012 has been installed,
devices with subsystem id 0x13c2:0x1011 did not work anymore.
Reason:
The driver for 0x13c2:0x1012 modified shared configuration data.
Fix:
Use separate configuration data for those devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When capturing a 60 Hz input the internal field ID is inverted. The
VIDIOC_INT_G_VBI_DATA didn't take that into account and so returned
XDS instead of CC and vice versa.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support 64 bit register IDs internally. Only allow root access to
this API (for both set and get). Note that actual 64 bit access only
becomes possible once the definition for v4l2_register is updated, but
this change clears the way for it from the viewpoint of the pvrusb2
driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tweak the encoder setup in order to stop it from corrupting the video
data when there is a disruption in the data flow (e.g. a channel change).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the implementation of the communication protocol for operating
the encoder, using updated knowledge about the encoder.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several special-case FX2 commands were being issued through
pvr2_write_u16() and pvr2_write_8(), but there's really nothing
special case about them. These date from a very early time in the
driver development. This patch removes these functions and replaces
their use with calls to pvr2_send_request.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a maintainability cleanup; use nice names for all the FX2
commands instead of raw bytes. This way we can easily find where we
issue FX commands.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The out of tree v4l-dvb build system didn't always override the kernel's
configuration settings with v4l-dvb's settings correctly. To work around
this, makefiles would define some new macro based on the setting of a
config variable. e.g. the pwc Makefile would define CONFIG_PWC_DEBUG if
CONFIG_USB_PWC_DEBUG (which is defined via Kconfig) was set.
The v4l-dvb build system should now always override correctly, and this
is no longer necessary. This patch gets ride of these extra defines and
just uses the CONFIG_* settings directly.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
input_register_device() was changed to return an error code instead of
being void in 2.6.15. Handle it with a macro wrapper in config.h. For
this to work, linux/input.h must be included before config.h. This
required some trivial header re-ordering in budget-ci.c and ttusb_dec.c.
In kernel 2.6.15-rc1 a helper function called setup_timer() was added to
linux/timer.h. Add to compat.h, but require that linux/timer.h be
included first to give the definition of struct timer_list.
A new 4GB DMA zone, __GFP_DMA32, was added in 2.6.15-rc2. Alias it to
__GFP_DMA on older kernels.
Handle another 2.6.15 "input_dev->dev to input_dev->cdev.dev" change for
some recently added code in cinergyT2.c.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before, root privileges were only needed to set hardware registers, not
to read them. On some hardware, reading from the wrong place at the
wrong time can hang the machine. So, to be consistent, root privileges
are required to read registers on all hardware.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Maybe someday there will be a device with a register address space >
32-bits, or maybe an i2c device which uses a protocol > 4 bytes long to
address its registers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed unregistering the vbi device for cards without analog tuner.
Thanks to Marco Schluessler <marco@lordzodiac.de> for pointing out this bug.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add phys-string, bustype, version, vendor and product to help udev and
others using EVIOCPHYS ioctl to identify the input device node.
Code taken (with little changes) from budget-ci.c
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Functions buffer_release() in bttv-driver.c and
vbi_buffer_release() in bttv-vbi.c are ending with:
bttv_dma_free(&fh->cap,fh->btv,buf);
For vbi it seems to be wrong. Both functions should end with:
bttv_dma_free(q,fh->btv,buf);
Thanks to Peter Schlaf <peter.schlaf@web.de> for pointing this.
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With debug>0, it will show mute/unmute and set frequency events
with debug>=4, it will show get frequency events
Also, some kernel CodingStyle fixes were done.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
fmtools use VIDIOCSTUNER, with, in turn, calls VIDIOC_S_INPUT on v4l1-compat.
So, those ioctls are required for V4L1 to work properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, vivi were simulating a scatter gather DMA transfer.
While this is academic, showing how stuff really works on a real PCI
device, this means a non-optimized code.
There are only two memory models that vivi implements:
1) kernel alloced memory. This is also used by read() method.
On this case, a vmalloc32 buffer is allocated at kernel;
2) userspace allocated memory. This is used by most userspace apps.
video-buf will store this pointer.
a simple copy_to_user is enough to transfer data.
The third memory model scenario supported by video-buf is overlay mode.
This model is not implemented on vivi and unlikely to be implemented on
newer drivers, since now, most userspace apps do some post-processing
(like de-interlacing).
After this patch, some cleanups may be done at video-buf.c to avoid
allocating pages, when the driver doesn't need a PCI buffer. This is the
case of vivi and usb drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The direct register access ioctls were defined as kernel internal only,
but they are very useful for debugging hardware from userspace and are
used as such. Officially export them.
VIDIOC_INT_[SG]_REGISTER is renamed to VIDIOC_DBG_[SG]_REGISTER
Definition of ioctl and struct v4l2_register is moved from v4l2-common.h
to videodev2.h.
Types used in struct v4l2_register are changed to the userspace
exportable versions (u32 -> __u32, etc).
Use of VIDIOC_DBG_S_REGISTER requires CAP_SYS_ADMIN permission, so move
the check into the video_ioctl2() dispatcher so it doesn't need to be
duplicated in each driver's call-back function. CAP_SYS_ADMIN check is
added to pvrusb2 (which doesn't use video_ioctl2).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for these ioctls to the video_ioctl2 system and the cx88
driver.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move filter caps from device caps to adapter caps for the megasky driver.
This fixes usb1.1 operation.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
QT1010:
- old qt1010-code totally rewritten and put in own kernel module
- same enhancements as my earlier QT1010 125kHz patch
- tuner initialization
- register 1f calculation
- register 20 calculation
- register 25 calculation
m920x: (MSI Megasky)
- use new QT1010 module instead of old code
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move .caps from the adapter properties to the device properties.
Thanks to Martin Schwier for confirming this fix.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes qt1010.h to use dvb_usb_device struct instead of a
dvb_usb_adapter for accessing the private area of the driver.
Without this patch my PC hard locks when an application tries to access
the DVB tuner.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The megasky_tuner_attach function is not specific to this device.
This patch renames it to qt1010_tuner_attach and moves it into the qt1010
header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cleanups and suggestions from Patrick Boettcher.
Dropped the mutex in m9206_rc_query using #if 0, because
M9206_CORE, M9206_I2C, M9206_FILTER and M9206_FW can be accessed
concurrently.
Thanks to both Aapo Tahkola and Patrick Boettcher.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- hardware pid filtering no longer enabled unless in usb 1.x mode
- more responsive rc handling
- some minor bug fixes and code refolding
- m9206_write delay dropped (doesn't seem to be needed)
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
qt1010 is a tuner used in some other devices, so this code should be put
into a separate file so that it could be reused by other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
update code to use dvb_attach()
update code to reflect recent changes to the dvb_usb framework
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the driver works in bulk mode supporting both USB 2.0 and
1.0 with and without hardware pid filters.
The ULi m9205 also supports isochronous transfer mode, but I have
dropped support for it because it depends on firmware and does not work
on all USB host chips. Further, I have no firmware with remote
controller support for this mode.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I noticed that udev does not create a symlink for the CinergyT2 remote input
device in /dev/input/by-id, which is required if I want to have a
unique device name for lircd.
The attached patch tries to achive this. However, udev still omits the
input device for /dev/input/by-id symlinks. I think something is still
not reported correctly.
Signed-off-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2 have only one tuner inside. However, as it were not handling
index, a call to v4l-info were returning as if it were an infinite
number of tuners:
$ v4l-info|grep VIDIOC_G_TUNER |head -5
VIDIOC_G_TUNER(0)
VIDIOC_G_TUNER(1)
VIDIOC_G_TUNER(2)
VIDIOC_G_TUNER(3)
VIDIOC_G_TUNER(4)
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2-encoder.c: In function 'pvr2_encoder_cmd':
pvrusb2-encoder.c:195: warning: format '%u' expects
type 'unsigned int', but argument 3 has type 'long unsigned int'
pvrusb2-encoder.c:205: warning: format '%u' expects
type 'unsigned int', but argument 3 has type 'long unsigned int'
pvrusb2-encoder.c: In function 'pvr2_encoder_vcmd':
pvrusb2-encoder.c:303: warning: format '%u' expects
type 'unsigned int', but argument 3 has type 'long unsigned int'
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds support for the combined S-Video/Composite input of the
Terratec Cinergy 1400 DVB-T.
Signed-off-by: Heiko Baums <heiko@baums-on-web.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Nexus CA needs to use a different routing on saa7115 module.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Terratec Cinergy HT PCI
Signed-off-by: Giorgio Moscardi <software@sukkology.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The video_ioctl2 conversion replaced the default from NTSC to PAL_BG.
This broke cx88-blackbird. Probably, there are some badness at this
driver, not doing all required stuff to change video standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch finishes cx88-blackbird conversion to use video_ioctl2. Video
standards are generated automatically inside videodev.c. the big ioctl
parser is removed, using, instead, video_ioctl2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l2_tvnorm were meant to describe video standards and its names to V4L2 API.
However, this were doing by some static structures at the driver.
This patch changes the internals in a way that, at the driver, only a
v4l2_tvnorm (a 64 bit integer) should be filled, with all supported
tvnorms. videodev will dynamically generate the proper API array
based on supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_ioctl2 handler provides V4L2 API parsing.
Using it makes the driver simpler, and isolates API parsing.
This allows future reusage of driver controls using other ways, like sysfs
and/or procfs and increases isolation of driver-specific handling from the
generic common ioctl processing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the previous patch, mplayer started but was polling the video
device forever without any video actually coming out. Further analysis
showed that it does a VIDIOC_S_FMT with width and height set to -1 (!!!).
The code handling this only cares that both are lower than the minimum
range allowed so it ends up setting the size to 19x17 (!!) This pretty
much breaks the encoder here. Even if this breakage is yet another (TM)
result of my setup, setting the size to 19x17 by default would surprise
most users IMHO.
So, special case for -1 and interpret this to be a request for the
default size, please. Users can then set their favorite size both
through mplayer and through sysfs.
With this patch, mplayer finally works in pvr:// mode (not that we
really gain anything over operating it through sysfs with lirc,
sometime I might actually get off my lazy a** and contribute this
setup too)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This should allow mplayer pvr:// to start. The trick is that no matter
what actual input we use under this "fake" one, it will be able to do
stereo :-)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio mode changes are not private to the audio chip - other I2C
modules need to see this as well. And since the command in question
is VIDIOC_S_TUNER which is a standard v4l2 command, we really should
be broadcasting it out. This change sets up a broadcast pathway for
VIDIOC_S_TUNER and also eliminates the now redundant code from the
audio chip handler.
This fix enables stereo reception for the FM radio
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Attempts to enumerate or operate on a group of EXT_CTRLS where the
group size is zero is OK; don't fail on such operations. At least one
application uses this to probe for the existence of this API so let it
succeed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This bug caused uninitalized data to be returned during a G_TUNER status poll.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The lack of a break statement in the handling of VIDIOC_S_TUNER caused
errors to result. Fixed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than hardcoding frequency ranges everywhere, rely on
VIDIOC_G_TUNER results wherever we can.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automodeswitch control was a feature that enable automatic radio /
tv switching based on the selected frequency. However since frequency
ranges can overlap and also since apparently in some cases it's
possible for the same frequency range to be both tv and radio in a
specific region, then this feature can't safely work. So it's removed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up use of VIDIOC_G_TUNER; we now correctly gather info from all
the I2C client modules. Also abide by V4L2_TUNER_CAP_LOW
appropriately.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds the missing VIDIOC_CROPCAP, G_CROP and S_CROP ioctls, permitting
applications to capture or overlay a subsection of the picture or to
extend the capture window beyond active video, into the VBI area and the
horizontal blanking. VBI capturing can start and end on any line,
including the picture area, and apps can capture different lines of each
field and single fields.
For compatibility with existing applications, the open() function
resets the cropping and VBI capturing parameters and a VIDIOC_S_CROP
call is necessary to actually enable cropping.
Regrettably in PAL-M, PAL-N, PAL-Nc and NTSC-JP mode the maximum image
width will increase from 640 and 768 to 747 and 923 pixels respectively.
Like the VBI changes however, this should only affect applications which
depend on former driver limitations, such as never getting more than 640
pixels regardless of the requested width.
Also, new freedoms require additional checks for conflicts and some
applications may not expect an EBUSY error from the VIDIOC_QBUF and
VIDIOCMCAPTURE ioctls. These errors should be rare though.
So far, the patch has been tested on a UP machine with a bt878 in PAL-
BGHI and NTSC-M mode using xawtv, tvtime, mplayer/mencoder, zapping/
libzvbi and these tools: http://zapping.sf.net/bttv-crop-test.tar.bz2
I'd be grateful about comments or bug reports.
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If assigned minor is 10 or greater, terminator will be put beyound the end.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Switch back to the previous input selection when the radio device is
closed - but only do that if the current input selection is still the
radio (i.e. it appears that it hasn't been messed with).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the input is switched by opening /dev/radioX, we must also commit
that change into the driver core.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up and tighten logic involving stream configuration. This
mainly involves changes to pvrusb2-v4l2.c, where we better clarify how
we use the stream configuration enum and implement a cleaner means to
control streaming for a given device node.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default volume of 65535 is too high. Make is something smaller.
Note that this _only_ changes the default value. Specifically, there
are no scaling or other more intrusive changes here. I'm just sick of
constantly having to reduce the volume every time I plug in and test
the device! (And unfortunately we can't do a better fix like scaling
the volume so that 65535 makes sense because doing so will screw up
any app - like MythTV - which expects the old scaling.) Too bad V4L
controls don't have better defined ranges.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trying to temporarily check that the stream is not claimed during open
of the radio device is at best a race condition. What's to stop
another app from claiming the stream anyway the instant after the
check is done? The implementation for this was dicey anyway. So it's
removed. The only "price" for this is that if /dev/radioX is opened
while streaming video, then the video stream is just going to switch
to radio mode anyway. If a user does this, he gets what he expects...
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Separate track radio versus tv frequency so that when we switch modes
we can also switch to a sane frequency appropriate for the mode. Also
implement logic to automate mode switching in certain cases.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement new method for doing integer range checking, so that we can
more intelligently range-check radio and tv ranges at once.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes implement correct audio routing for radio mode on a
24xxx device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Report and set correctly converted frequency to/from a V4L2 app.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frequency units in V4L2 are apparently different when in radio mode
compared to tv mode. Why? Who knows. This change adapts the driver
appropriately - so that internally we always only deal in Hz and don't
have to muck with craziness like this.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A conversion from Hz to V4L frequency units was accidentally removed
by an earlier change. Restore it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We can't allocate v4l device structures in a block, since the v4l core
governs when each device actually gets freed. This bug was introduced
as part of the core radio implementation. Fix it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support specification of vbi and radio device minor numbers in a
manner similar to the video device minor number.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ensure we don't accidentally broadcast the standard while in radio mode.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The initial radio implementation used different units for tuning when
in radio mode. This changes everything to Hz.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use separate enum for get/store of minor number; we want pvr2_config
to go away eventually and since it really means something different,
don't use it here
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The "main" V4L2 interface patch. This is yet very incomplete, incorrect and
probably inappropriate for inclusion as-is, but at least with this I 'm able
to tune and play radio through a V4L2 program (pvr-radio.c, a "thumb" version
of ivtv-radio.c with just the essentials).
Therefore, it kinda gives an idea of what is needed to support this, hm,
interface (partly used also by e.g., kradio). Please point out any mistakes
on this code. I 'm sure I 'm messing up some struct initialization somewhere
but currently I 'm too lazy to actually think this through until I complete
the functionality (e.g., handle the VIDIOC_S_STD, ENUMINPUT, etc ioctls
appropriately).
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add (and expose) a new function, pvr2_channel_check_stream_no_lock(), in
pvrusb2-context.c. This is hopefully the last V4L2 interface related patch
to change anything outside pvrusb2-v4l2.c.
We need this to implement the open() for the radio device. The reason is
that within the *enter_context() section of open() we need to ensure nobody
is streaming and if we cannot, we should cleanup after ourselves and return
-EBUSY. We cannot just use claim_stream() because:
1) That would cause a deadlock trying to re-acquire the context lock
2) We only need to ensure that nobody is streaming. We don't need to
actually acquire the stream.
Again, this is a kinda ugly patch. Feel free to improve.
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the first patch in preparation of the V4L2/IVTV radio interface.
It does away with the assumption of only one minor per device. It also
adds a file to show the radio minor as well. This can be useful for a
program like pvr-radio.c (when it grows up), since this way it can search
for the minor of the /dev/radioX device it opened and use the video minor
of the same driver instance to get to the actual stream.
The implementation looks kinda ugly. Feel free to improve (that is the
reason behind separate patches anyway).
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the previous patch we exploited the get_{min,max}_value facility to adjust
min/max allowable frequencies on the fly, depending on tuner mode.
Unfortunately, this facility was not used inside the *sym_to_val() function
that translates what we echo to sysfs, which means we got an -ERANGE despite
asking for a frequency between what we read to be min/max.
This patch corrects this small omission.
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the logic that:
a) Ensures /sys/class/pvrusb2/sn-*/ctl_frequency/{max,min}_val are
"automagically" reset to sane values on each mode change.
b) Allows tuning to a radio frequency by something like:
echo `perl -e "print int(94.9*16000 + 0.5)"` \
> /sys/class/pvrusb2/sn-*/ctl_input/cur_val
The trick was to take advantage of the already existing .get_{min,max}_value
function pointers in pvr2_ctrl, to "dynamically override" the hardcoded values
for min/max frequency at runtime.
For a moment I thought to dispose of the hardcoded MIN/MAX_FREQ and use the
hirange/lowrange fields of the v4l2_tuner struct instead, but then I see that
tuner-core.c kinda hardcodes these as well, so I decided to not bother.
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the logic that supports switching modes via e.g.,
echo radio > /sys/class/pvrusb2/sn-*/ctl_input/cur_val.
To do the mode switching we need to:
a) broadcast AUDC_SET_RADIO and
b) issue the CX2341X_ENC_MUTE_VIDEO command to the encoder.
The first is done by adding a new pvr2_i2c_op and having it trigger on
input change, the second by adding this command in pvr2_encoder_start()
and requesting an encoder restart on input change by setting
stale_subsys_mask appropriately.
The clues about AUDC_SET_RADIO and CX2341X_ENC_MUTE_VIDEO were kindly
provided by Hans Verkuil on the pvrusb2 mailing list. The idea to
implement mode switching this way (on input change) is due to Mike Isely.
Why AUDC_SET_RADIO/VIDIOC_S_STD are used for switching? I can 't be sure,
but I think this can be traced to a cornell student being the first to
implement radio support in ivtv "as a different standard". I think the
rest just evolved from there (it 's in the ivtv ML archives).
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several potential troubles on vivi waitqueue code:
- Watchdog timer should be reset at every received frame;
- Watchdog timer should be reset at the beginning of vivi_thread();
- Checks for errors when creating a newer thread with kernel_thread();
- Wake up vivi_thread() after creating it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If for some reason vivi_thread() fails, vivi will suffer an OOPS at
thread stop code, since waitqueue wouldn't be properly initializated.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The keymap is based on a previous patch by Jussi Kukkonen.
This remote is identified by subsystem_device id 0x1010.
Signed-off-by: Ville-Pekka Vainio <vpivaini@cs.helsinki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bill Dirks asked me to update his entries at kernel files, since
he change his e-mail.
I've also updated a few web broken links or obsolete info to the curent
sites where V4L drivers and API are being discussed currently.
CC: Bill Dirks <bill@thedirks.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for SN9C105 and SN9C120
- Add some more USB device identifiers
- Add support for OV7660
- Implement audio ioctl's and VIDIOC_ENUM_FRAMESIZES
- Add preliminary support for 0x0c45/0x6007
- Documentation updates
- Generic improvements
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ultraview DVB-T Lite is a clone of DViCO FusionHDTV DVB-T Lite
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Replaces the info statements with printk(KERN_INFO statements.
This will cut down on the useless information which is showing up
in the kernel messages log file.
Signed-off-by: Dwaine P. Garden <DwaineGarden@rogers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PS.: Part of the changes at the original patch were removed due to the changes
done at commit 52c14e794f6ce345343a6b8fc98ea4e0ba2dfce4
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
No need for redundant argument check for module_put()
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the following compile error:
<-- snip -->
...
LD drivers/media/video/built-in.o
drivers/media/video/saa7134/built-in.o:(.data+0x85ec): multiple definition of `ir_rc5_remote_gap'
drivers/media/video/bt8xx/built-in.o:(.data+0x734c): first defined here
drivers/media/video/saa7134/built-in.o:(.data+0x85f0): multiple definition of `ir_rc5_key_timeout'
drivers/media/video/bt8xx/built-in.o:(.data+0x7350): first defined here
make[4]: *** [drivers/media/video/built-in.o] Error 1
<-- snip -->
Since this variables were needlessly global, this patch implements the
trivial fix of making them static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some long time unused code under some media driver source files.
There's no need of keeping it at mainstream.
Those unused code will remain available at V4L/DVB master tree and also at
kernel history.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the initialization of alps tdee4 tuner in
flexcop-fe-tuner.c to match what is used in the old driver that was
written specifically for Cablestar cards by Patrick Boettcher. This
patch should make Cablestar2 work again with recent dvb drivers without
breaking other stv0297 based cards.
Signed-off-by: Antti Seppala <ajhseppa@niksula.hut.fi>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Second part of the patch to make the autosearch work again with DiB3000P/MC.
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a board definition for the Encore ENL-TV card, and
adds its PCI subdevice to the ID table.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The commands CX2341X_DEC_SET_AUDIO_OUTPUT, CX2341X_DEC_SET_AV_DELAY and
CX2341X_ENC_SET_3_2_PULLDOWN are not implemented in the Conexant firmware.
So these commands are removed. This also means that the V4L2_CID_MPEG_VIDEO_PULLDOWN
control in cx2341x.c and pvrusb2-hdw.c is removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This makes a second CVBS input available.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Besides adding the board specific code, this patch moves
the RC5 decoding code from bt8xx to ir-functions.c to make it available
for all drivers.
Signed-off-by: Marc Fargas <telenieko.telenieko.com>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Declare the parent device of i2c_adapter devices each time we can
easily do so. It makes the i2c_adapter appear at the right place in
the device tree, rather than as a platform device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: v4l-dvb-maintainer@linuxtv.org
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify the few instances where a call to "get_zeroed_page()" is closely
followed by an unnecessary call to memset() to clear that page.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: chas williams <chas@cmf.nrl.navy.mil>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are doing ->buf_prepare(buf) before adding buf to q->stream list. This
means that videobuf_qbuf() should not try to re-add a STATE_PREPARED buffer.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There's a problem, pointed by Meelis Roos <mroos@linux.ee>, that, on ppc32 arch,
with some gcc versions (noticed with prerelease 4.1.2 20061115), compilation
fails, due the lack of __ucmpdi2 to do the required 64-bit comparision.
This patch takes some sugestions made by Andrew Morton <akpm@osdl.org>,
Stelian Pop <stelian@popies.net> and Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
autodetect LG TAPC G701D as tuner type 37.
Thanks to Adonis Papas, for pointing out the missing autodetection
for this tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We have a DMA32 zone now, lets use it to make sure the card
can reach the memory we have allocated for the video frame
buffers.
Signed-off-by: Gerds Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MSI TV@nywhere Plus. Fix radio, S-Video and external analog audio in
as far we can know currently.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Or status flags together in DECODER_GET_STATUS instead of and-zapping them.
Signed-off-by: Martin Samuelsson <sam@home.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Host endianess does not affect the order that pixel rgb data comes
in from the quickcam (the values are bytes, not words or longs). The
driver is erroniously swapping the order of rgb values for big endian
machines. This patch is needed get the Quickcam communicator working
on big endian machines (tested on powerpc)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Suspending with the cx88xx module loaded causes the system to lock up
because the cx88_audio_thread kthread was missing a try_to_freeze()
call, which caused it to go into a tight loop and result in softlockup
when suspending. Fix that.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vivi.c uses the KM_BOUNCE_READ with local interrupts enabled.
This means that if a disk interrupt occurs while vivi.c is using this
fixmap slot, the vivi.c driver will, upon return from that interrupt, find
that the fixmap slot now points at a different physical page.
The net result will probably be rare corruption of disk file contents,
because viv.c will now be altering the page which the disk code was
recently using.
Thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Coverity checker spotted that in usbvision_v4l2_read(), the variable
"frmx" is never assigned any value different from -1, but it's used an
an array index in "usbvision->frame[frmx]".
Thanks to Adrian Bunk <bunk@stusta.de> for warning about that.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
reference to .init.text: from .text between 'cx88_card_setup'
(at offset 0x68c) and 'cx88_risc_field'
Caused by leadtek_eeprom() being declared __devinit and called from
a non-devinit context.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
include/media/ir-common.h:78: error: field 'work' has incomplete type
drivers/media/common/ir-functions.c: In function 'ir_rc5_timer_end':
drivers/media/common/ir-functions.c:301: error: 'jiffies' undeclared (first use in this function)
drivers/media/common/ir-functions.c:301: error: (Each undeclared identifier is reported only once)
drivers/media/common/ir-functions.c:301: error: for each function it appears in.)
drivers/media/common/ir-functions.c:347: error: 'HZ' undeclared (first use in this function)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- CAFE_CCIC needs to depend on PCI, else "allyesconfig" breaks
on systems without PCI
- em28xx-video can't udelay(2500) else "allyesconfig" breaks
on systems that refuse to spin that long (I saw it on ARM)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ioremap() is called twice to same resource.
The returen value of first one is not error-checked.
second one is complely ignored.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of kthread_run() should be checked by IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of kthread_run() should be checked by IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Freeing data including list_head in list_for_each() is not safe.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We shouldn't dereference "cam" when we already know it's NULL.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The temporal filter is forced off when scaling. The VIDIOC_LOG_STATUS
handler still showed the old temporal filter. It is now consistent with
the real temporal filter value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
