Add a short delay when stopping the decoder, allowing it to settle and
preventing some unexpected interaction with other firmware commands.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Tested-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added small delay on device open & close to allow hardware to settle. Move yuv
register restore to before the decoder firmware call to stop playback.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For yuv video output, pass fake values to avoid firmware trying to change
video standard.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check firmware state when loading module & if firmware is not responding exit
with an error. When module is unloaded, only disable the framebuffer & not all
decoder output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PRIORITY is also part of the ioctls that need to check the
access priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_prio_init/open/close returned an int when in fact they would
always return 0. Make these void functions.
v4l2_prio_close and v4l2_prio_check pass an enum v4l2_priority as a
pointer for no good reason. Replace with a normal enum v4l2_priority
argument.
These changes will simplify the work of moving priority handling into
the v4l core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that video_ioctl2 no longer clobbers the argument for _IO() ioctls we
can move these into vidioc_default where they really belong.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaces most of the occurences of IR keytables on V4L drivers by a macro
that evaluates to provide the name of the exported symbol.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of the magic number 0x28c0 used in several places in the ivtv and
ivtvfb driver and define the register address to a meaningful name.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changing the decoder video standard just prior to, or during, the output of
the lower field may result in a hard system lock. To avoid this, try to ensure
the firmware call occurs only during the first 100 lines of the top field.
(Minor comment addition and a line break added Andy Walls <awalls@radix.net>.)
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a capture is started, the firmware also appears to start a secondary
stream. Unless this secondary stream is also stopped, the encoder will remain
active and not reinitialise for the next capture. Unfortunately, setting up
the video source can glitch the encoder and result in undesirable effects that
this initialisation will clear.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Combine the two 150 ms delays into a single 300 ms delay. Ian Armstrong has
noted that the delay between CX2341X_ENC_INITIALIZE_INPUT and
CX2341X_ENC_START_CAPTURE can cause problems if the temporal filter is allowed
to be enabled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Based on experiments by Eric Wescott, edit the Sony GigaPocket (Kikyou)
card entry video and audio mux settings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a slightly modified version of Eric Anderson's original patch
for the Sony Giga Pocket board. It has been updated to apply to the
latest ivtv driver version by Hans Verkuil <hverkuil@xs4all.nl> and
Andy Walls <awalls@radix.net>. Also Andy Walls modified the patch to
use a new Sony BTF-Pnx01Z tuner entry based on Eric Anderson's experimental
findings for the bandswitch.
>From Eric Anderson's original email:
1. The tuner on the card doesn't seem to match any standard
ones. I modified an existing tuner entry. Ideally a new tuner
entry should be created. (The only difference from the one I
modified is that the low-to-mid range frequency cut-off is
slightly different, as are the bit config settings.)
2. It wasn't obvious how to choose a second audio input other
than using "radio" as an option. Basically there's two GPIO
audio inputs. Using radio allowed me to avoid major restructuring
to the code. (perhaps other cards don't have this often...)
3. It's not clear that there's a mute setting that works. Not
sure why.
4. I haven't had a chance to test the two Svideo inputs. I set
them to COMPOSITE1 and SVIDEO2, but I'm not sure those are the
correct settings. The standard composite video inputs seem to work.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv_api_get_data() was performing more PCI MMIO than needed, resulting
often in it accounting for more than half the total time spent in
ivtv_irq_handler(). Now it only reads at most 7 of the 16 mailbox data words
over the PCI bus, and in some instances only 2 or 3 data words as needed.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Martin Dauskardt <martin.dauskardt@gmx.de> has done extensive testing on what
values can be used and and concluded that only 300 ms total is required to
avoid bad video effects such as occasional black screen and short sync
disturbances. Furthermore he determined how this 300 ms was split between
the two msleep()s did matter very much, so he suggested 150ms/150ms as one
acceptable alternative that is implemented here.
Many thanks go to Martin.
Tested-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change attempts to fix the ivtv tinny audio problem by keeping digitizer
to encoder audio clocks running, while disabling the video clocks as needed to
avoid unpredictable PCI bus hangs.
To accomplish this, for the cx25840 module enabling of audio streaming had
to be separated from enabling video streaming, requiring an additional
v4l2_subdev_audio_op and calls to this new op in the pvrusb2 and ivtv drivers.
The cx231xx and cx23885 driver use the cx25840 module for affecting only
video on s_stream calls, so those drivers needed no change.
The CX23418 hardware does not exhibit either the tinny audio problem nor the PCI
bus hang, so the cx18 driver did not need corresponding changes.
CX2341[56] based cards that are not using the CX2584x family of chips
do not seem to be affected by the tinny audio problem, and this change should
not affect how they are configured. It will delay their first capture by
starting by another 300 msec though.
Many thanks go to Argus <pthorn-ivtvd@styx2002.no-ip.org> and
Martin Dauskardt <martin.dauskardt@gmx.de> whose persistent testing and
investigation of this problem will hopefully fix this problem once and for all
for many ivtv users.
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Reported-by: Argus <pthorn-ivtvd@styx2002.no-ip.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several DMA related interrupts which wake up the dma_waitq. The udma
routines use this queue while they wait for their transfer to complete. When
woken, the udma routine will check the IVTV_F_I_UDMA_PENDING & IVTV_F_I_UDMA
flags to see if the transfer is still queued or has finished. However, a small
window exists between the IVTV_F_I_UDMA_PENDING flag being cleared and the
IVTV_F_I_UDMA flag being set. Given that the completion of an unrelated DMA
transfer may wake up the udma routine, it's possible for this check to fail
and the udma routine will start unmapping pages when the transfer has only
just started. The result of this is unpredictable.
This fix simply delays the clearing of the IVTV_F_I_UDMA_PENDING flag until
after IVTV_F_I_UDMA has been set.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the minor number in kernel log messages, use the device
node name as returned by the video_device_node_name() function. This
makes debug, informational and error messages easier to understand for
end users.
[mchehab.redhat.com: removed tm6000 changes as tm6000 is not ready yet for submission even on staging]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix all device drivers to use the new video_device_node_name function.
This also strips kernel log messages from the "/dev/" prefix, has the device
node location is a userspace policy decision unknown to the kernel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid legacy IR I2C probing for PVR-150, PVR-500, and PVR-350 cards. This
still probes, but restricts the possbile addresses probed per card.
Also removed legacy probe addresses for the KNC and PixelView cards which are
not supported by ivtv as far as I know.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add explicit support for the AVerTV M116 for use with the ir-kbd-i2c module.
This also eases future support for other AVerMedia ivtv boards with the same
microcontroller program at I2C address 0x40.
This is a reworked version of an earlier patch that was...
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This avoids collisions of legacy IR controller probing with known I2C devices
in the card definitions in ivtv-cards.c. I2C driver modules for device listed
explicitly in a card definition should always take precedence over a probe
guessing where and IR controller may be.
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a module parameter to adjust I2C SCL clock period per board. This allows
some experimental fine tuning by end users to overcome quirky I2C device
problems.
Reported-by: "Aleksandr V. Piskunov" <aleksandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of the following drivers in media video:
drivers/media/video/ivtv/ivtv-driver.c
drivers/media/video/cx18/cx18-driver.c
drivers/media/video/davinci/dm355_ccdc.c
drivers/media/video/davinci/dm644x_ccdc.c
drivers/media/video/saa7164/saa7164-core.c
drivers/media/video/saa7134/saa7134-core.c
drivers/media/video/cx23885/cx23885-core.c
Cc: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Andy Walls <awalls@radix.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warn when the desired device node number is already in use, except when
the new video_register_device_no_warn function is called since in some
use-cases that warning is not relevant.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the subdev_s_std() method from the GPIO subdev. It appears it was
used in the past to effect the switch back from radio mode to tuner mode,
but it had a side effect that is improper and against the V4L2 spec, when
you were not in radio mode. Whenever the video stanadrd was changed, the
GPIO audio mux was set back to the tuner audio input, even if you were set
to a Line In input.
Thanks to Ravi A. for doing the troubleshooting to point me right to the
problem.
Reported-by: Ravi A <asvravi@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My initial change left the AVerMedia UtlraTV 1500MCE card entry out of the
list of cards to check during the probe. This change adds it to the
ivtv_card_list[].
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This mistakenly tests against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke
the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control
was broken for all drivers that use the cx2341x module and the USER class
control was broken for ivtv and cx18.
This change adds back proper class control support.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probe I2C addresses 0x71 and 0x6b for IR receiver devices (for the
PVR150 and Adaptec cards, respectively.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
