With commit 8bc2a40730 ("rtc: ds1307: add support for the
DT property 'wakeup-source'") we lost the ability for rtc irq
functionality for devices that are actually hooked on a real IRQ
line and have capability to wakeup as well. This is not an expected
behavior. So, instead of just not requesting IRQ, skip the IRQ
requirement only if interrupts are not defined for the device.
Fixes: 8bc2a40730 ("rtc: ds1307: add support for the DT property 'wakeup-source'")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Michael Lange <linuxstuff@milaw.biz>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
while retrieving temperature from ds3231, the result may be overflow
since s16 is too small for a multiplication with 250.
ie. if temp_buf[0] == 0x2d, the result (s16 temp) will be negative.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.
With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.
An example for the entry in the .dts file:
rtc: ds1337@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
wakeup-source;
If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This makes the generated code slightly smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With the actual code, read_alarm() always returns -EINVAL when called
during the RTC device registration. This prevents from retrieving an
already configured alarm in hardware.
This patch fixes the issue by moving the HAS_ALARM bit configuration
(if supported by the hardware) above the rtc_device_register() call.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit 3fffd12839 ("i2c: allow specifying
separate wakeup interrupt in device tree") we have
automatic wakeup irq support for i2c devices. That
commit missed the fact that rtc-1307 had its own
wakeup irq handling and ended up introducing a
kernel splat for at least Beagle x15 boards.
Fix that by reverting original commit _and_ passing
correct interrupt names on DTS so i2c-core can
choose correct IRQ as wakeup.
Now that we have automatic wakeirq support, we can
revert the original commit which did it manually.
Fixes the following warning:
[ 10.346582] WARNING: CPU: 1 PID: 263 at linux/drivers/base/power/wakeirq.c:43 dev_pm_attach_wake_irq+0xbc/0xd4()
[ 10.359244] rtc-ds1307 2-006f: wake irq already initialized
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
mcp794xx alarm registers must be written in BCD format. However, the
alarm programming logic neglected this by adding one to the value
after bin2bcd conversion has been already done, writing bad values
to month register in case the alarm being set is in October. In this
case, the alarm month value becomes 0x0a instead of the expected 0x10.
Fix by moving the +1 addition within the bin2bcd call also.
Fixes: 1d1945d261 ("drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With the recent pinctrl-single changes, SoCs such as Texas
Instrument's OMAP processors can treat wake-up events from deeper idle
states as interrupts.
Let's add support for the optional second interrupt for wake-up using
the generic wakeirq support added in commit 4990d4fe32 ("PM /
Wakeirq: Add automated device wake IRQ handling")
Finally, to pass the wake-up interrupt in the dts file,
interrupts-extended property needs to be passed.
This is similar in approach to commit 2a0b965cfb ("serial: omap: Add
support for optional wake-up") + ee83bd3b64 ("serial: omap: Switch
wake-up interrupt to generic wakeirq")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is always a good practice to keep the #includes sorted
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since we are not doing anything fancy in remove function that requires
us to sequence IRQ free operation, we might as well switch over to devm_
equivalent of managed IRQ allocation and remove the explicit free_irq
since it'd be done automatically at remove.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver currently emulates the concept of threaded IRQ using a
workqueue, which it really does not need to. Instead, switch over to
threaded_irq handlers which is meant precisely for the same purpose.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alarm interrupt enable register is at offset 0x7, while the time
registers for the alarm follow that. When we program Alarm interrupt
enable prior to programming the time, it is possible that previous
time value could be close or match at the time of alarm enable
resulting in interrupt trigger which is unexpected (and does not match
the time we expect it to trigger).
To prevent this scenario from occuring, program the ALM0_EN bit only
after the alarm time is appropriately programmed.
Ofcourse, I2C programming is non-atomic, so there are loopholes where
the interrupt wont trigger if the time requested is in the past at
the time of programming the ALM0_EN bit. However, we will not have
unexpected interrupts while the time is programmed after the interrupt
are enabled.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
MCP7940x is same RTC as MCP7941x. The difference is that MCP7941x chips
contain additional EEPROM on a different i2c address.
DS1307 driver already supports MCP7941x, so just add a new i2c device id
and rename functions and defines accordingly.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some DS13XX devices have "trickle chargers". Introduce a device tree
binding for specifying the trickle charger configuration for ds1339.
Only ds1339 dt binding is supported because this is the only chip I have.
I _assume_ the code would have worked on other allready supported chips.
However I cannot check the resistor values for the other chips or test
them. For other chips the driver code works as earlier Eg. it does not
check the dt bindings at all
Signed-off-by: Matti Vaittinen <matti.vaittinen@nsn.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add alarm support for the Microchip RTC devices MCP794xx. Note that two
programmable alarms are provided by the chip but only one is used by the
driver.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow the creation of the sysfs attribute wakealarm, this
patch moves the device_set_wakeup_capable() call above the RTC device
registration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable want_irq is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'client->irq' was not released on error. Fix it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current usage of commas instead of semicolons is not wrong, but
affects the readability of the code.
Also, the code would break, if someone puts something between those two
assignments.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_dbg() is preferred to pr_debug().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-ds1307 driver does not properly handle block operations bigger
than 32 bytes in either of the two modes supported (SMbus native, or
emulated if not supported by the SMbus platform driver).
It also does not properly handle userland-supplied input (block
operation length) through sysfs and may suffer a type of buffer overrun.
The driver has been modified with proper input validation, buffer sizes,
and now splits block transfers bigger than 32 bytes into separate
transfers.
Explanation : Buffer size allocated is I2C_SMBUS_BLOCK_MAX which equals
to 32 as per the SMbus spec. Reads and write may be up to 56 bytes (to
the NVRAM). This patch allocated a 255 byte buffer, the maximum
allowable (address is an u8). It's not only a buffer problem, SMbus
only supports up to 32 bytes transfer at once, so it's needed to split
bigger transfers.
Patch successfully tested on 3.2.27; cleanly applies on 3.7-rc4.
[akpm@linux-foundation.org: rework code to avoid 80-column overflows]
Signed-off-by: Bertrand Achard <ba@cykian.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DS13XX devices have "trickle chargers". Its configuration register
is at different locations, the setup is the same, though. Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds1307 was kzalloced, so no need to zero members of the struct.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add struct bin_attribute initialization to fix the following bug:
rtc-ds1307 3-0068: rtc core: registered ds1307 as rtc0
BUG: key cfb14fcc not in .data!
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2986 sysfs_add_file_mode+0x84/0xdc()
Modules linked in:
[<c0018d94>] (unwind_backtrace+0x0/0xf8) from [<c0031f7c>] (warn_slowpath_common+0x4c/0x64)
[<c0031f7c>] (warn_slowpath_common+0x4c/0x64) from [<c0031fb0>] (warn_slowpath_null+0x1c/0x24)
[<c0031fb0>] (warn_slowpath_null+0x1c/0x24) from [<c012f7ac>] (sysfs_add_file_mode+0x84/0xdc)
[<c012f7ac>] (sysfs_add_file_mode+0x84/0xdc) from [<c04b11e4>] (ds1307_probe+0x5e4/0x6ac)
[<c04b11e4>] (ds1307_probe+0x5e4/0x6ac) from [<c036e600>] (i2c_device_probe+0xdc/0x108)
[<c036e600>] (i2c_device_probe+0xdc/0x108) from [<c02cdf84>] (driver_probe_device+0x90/0x210)
[<c02cdf84>] (driver_probe_device+0x90/0x210) from [<c02ce198>] (__driver_attach+0x94/0x98)
[<c02ce198>] (__driver_attach+0x94/0x98) from [<c02cc824>] (bus_for_each_dev+0x50/0x7c)
[<c02cc824>] (bus_for_each_dev+0x50/0x7c) from [<c02cd780>] (bus_add_driver+0x184/0x244)
[<c02cd780>] (bus_add_driver+0x184/0x244) from [<c02ce43c>] (driver_register+0x78/0x12c)
[<c02ce43c>] (driver_register+0x78/0x12c) from [<c03701ac>] (i2c_register_driver+0x2c/0xb4)
[<c03701ac>] (i2c_register_driver+0x2c/0xb4) from [<c0008798>] (do_one_initcall+0x34/0x178)
[<c0008798>] (do_one_initcall+0x34/0x178) from [<c0691860>] (kernel_init+0xdc/0x194)
[<c0691860>] (kernel_init+0xdc/0x194) from [<c0013cf0>] (kernel_thread_exit+0x0/0x8)
Since commit 6992f53349 ("sysfs: Use one lockdep class per sysfs
attribute") this initialization is required.
Reported-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Generalise NVRAM to support RAM with other size and offset, such as the
64 bytes of SRAM on the mcp7941x.
[rdunlap@xenotime.net: fix printk format warning]
Signed-off-by: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do some cleanup of the comment sections as well as correct some
formatting issues reported by checkpatch.pl.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to have two seperate if-blocks for setting up the irq.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: David Anders <danders.dev@gmail.com>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The chip_desc table is suboptimal. Currently it requires an entry for
every new chip type, even if it is empty. This has already been
forgotten for the ds1388. Refactor the code, so new entries are only
needed, when they chip type really needs a (non-empty) description.
Also make the table visually more appealing.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add initial support for the microchip mcp7941x series of real time clocks.
The mcp7941x series is generally compatible with the ds1307 and ds1337 rtc
devices from dallas semiconductor. minor differences include a backup
battery enable bit, and the polarity of the oscillator enable bit.
Signed-off-by: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PT7C4338 chip is being manufactured by Pericom Technology Inc. It is a
serial real-time clock which provides:
1) Low-power clock/calendar.
2) Programmable square-wave output.
It has 56 bytes of nonvolatile RAM. Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some rtc drivers use the ioctl method instead of the alarm_irq_enable
method for enabling alarm interupts. With the new virtualized RTC
rework, its important for drivers to use the alarm_irq_enable instead.
This patch converts the drivers that use the AIE ioctl method to
use the alarm_irq_enable method. Other ioctl cmds are left untouched.
I have not been able to test or even compile most of these drivers.
Any help to make sure this change is correct would be appreciated!
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ds1307 driver misreads the ds1388 registers when checking for 12 or 24
hour mode. Instead of checking the hour register it reads the minute
register. Therefore the driver thinks minutes >= 40 has the 12HR bit set
and resets the minute register by zeroing the high bits. This results in
minutes are reset to 0-9, jumping back in time 40 or 50 minutes. The time
jump is also written back to the RTC.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RTC core won't allow wakeup alarms to be set if RTC devices' parent (i.e.
i2c_client or spi_device) isn't wakeup capable.
For I2C devices there is I2C_CLIENT_WAKE flag exists that we can pass via
board info, and if set, I2C core will initialize wakeup capability. For
SPI devices there is no such flag at all.
I believe that it's not platform code responsibility to allow or disallow
wakeups, instead, drivers themselves should set the capability if a device
can trigger wakeups.
That's what drivers/base/power/sysfs.c says:
* It is the responsibility of device drivers to enable (or disable)
* wakeup signaling as part of changing device power states, respecting
* the policy choices provided through the driver model.
I2C and SPI RTC devices send wakeup events via interrupt lines, so we
should set the wakeup capability if IRQ is routed.
Ideally we should also check irq for wakeup capability before setting
device's capability, i.e.
if (can_irq_wake(irq))
device_set_wakeup_capable(&client->dev, 1);
But there is no can_irq_wake() call exist, and it is not that trivial to
implement it for all interrupts controllers and complex/cascaded setups.
drivers/base/power/sysfs.c also covers these cases:
* Devices may not be able to generate wakeup events from all power
* states. Also, the events may be ignored in some configurations;
* for example, they might need help from other devices that aren't
* active
So there is no guarantee that wakeup will actually work, and so I think
there is no point in being pedantic wrt checking IRQ wakeup capability.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible to have RTC irq shared with other device (e.g.
mpc8349e-mitx board shares ds1339 irq with phy one). Handle this in
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is not executed before ds1307->rtc has been successfully
initialized to the result of calling rtc_device_register. Thus the test
that ds1307->rtc is not NULL is always true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@
x = rtc_device_register(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc_update_irq() might be called with irqs enabled, if a interrupt
handler was registered without IRQF_DISABLED. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_lock/spin_unlock.
Also update kerneldoc and drivers which do extra work to follow the
current interface spec, as suggestted by David Brownell.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add ds3231 variant. For that, the BBSQI bit position was changed from a
simple define into a lookup-array as it differs. This also removes
writing to an unused bit in case of the ds1337.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
