This is not quite the complete support, since we're not yet shipping
intvec_64.S, but it is the support relevant to the set of files we are
currently shipping, and makes it easier to track changes between
our internal sources and our public GIT repository.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
While not a port to KVM (yet), this change modifies the kernel
to be able to build either at PL1 or at PL2 with a suitable
config switch. Pushing up this change avoids handling branch
merge issues going forward with the KVM work.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we were using -1023, which is fine for normal syscall
error returns, but the common value in use for other platforms
is -4095, and one Tilera-specific driver does use values in the
-1100 range, so tickled this bug.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
With this change we now include <asm-generic/syscalls.h> into the "tile"
version of the header. To take full advantage of the prototypes there,
we also change our naming convention for "struct pt_regs *" syscalls so
that, e.g., _sys_execve() is the "true" syscall entry, which sets the
appropriate register to point to the pt_regs before calling sys_execve().
While doing this I realized I no longer needed the fork and vfork
entry point stubs, since those functions aren't in the generic
syscall ABI, so I removed them as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This "bpt_code" instruction was killed off in our development line a while
ago (the actual definition of bpt_code that is used is in kernel/traps.c)
but I didn't push it for 2.6.36 because it seemed harmless and I didn't
want to try to push more than absolutely necessary.
However, we recently fixed a bug in our gcc that had been causing
"-gdwarf2" not to be passed to the assembler, and passing this flag causes
an erroneous assembler failure in the presence of code in a data section,
sometimes. While we'd like to track down the bug in the assembler,
we'd also like to make sure 2.6.36 builds with the current toolchain,
so I'm removing this dead code as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Until now, the tile architecture ABI for syscall return has just been
that r0 holds the return value, and an error is only signalled like it is
for kernel code, with a negative small number.
However, this means that in multiple places in userspace we end up writing
the same three-cycle idiom that tests for a small negative number for
error. It seems cleaner to instead move that code into the kernel, and
set r1 to hold zero on success or errno on failure; previously, r1 was
just zeroed on return from the kernel (to avoid leaking kernel state).
This way a single conditional branch after the syscall is sufficient
to test for the failure case. The number of cycles taken is the same,
but the error-checking code is in just one place, so total code size is
smaller, and random userspace syscall code is easier to understand.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This network (the "UDN") connects all the cpus on the chip in a
wormhole-routed dynamic network. Subrectangles of the chip can
be allocated by a "create" ioctl on /dev/hardwall, and then to access the
UDN in that rectangle, tasks must perform an "activate" ioctl on that
same file object after affinitizing themselves to a single cpu in
the region. Sending a wormhole-routed message that tries to leave
that subrectangle causes all activated tasks to receive a SIGILL
(just as they would if they tried to access the UDN without first
activating themselves to a hardwall rectangle).
The original submission of this code to LKML had the driver
instantiated under /proc/tile/hardwall. Now we just use a character
device for this, conventionally /dev/hardwall. Some futures planning
for the TILE-Gx chip suggests that we may want to have other types of
devices that share the general model of "bind a task to a cpu, then
'activate' a file descriptor on a pseudo-device that gives access to
some hardware resource". As such, we are using a device rather
than, for example, a syscall, to set up and activate this code.
As part of this change, the compat_ptr() declaration was fixed and used
to pass the compat_ioctl argument to the normal ioctl. So far we limit
compat code to 2GB, so the difference between zero-extend and sign-extend
(the latter being correct, eventually) had been overlooked.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.
This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
