Rename the register access macros and use standard _relaxed()
ops instead of __raw variants with explicit byte swapping.
The original driver used the ppc-specific in/out_le32(). When it
was adapted to other systems, these were added to the driver
under ifdefs. However, those names are not defined as macros on
ppc, so it ended up replacing them there as well with altered
semantics. This patch restores the original semantics on ppc and
makes the accesses no less strict on other systems.
Also fixes too many sparse warnings to count.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer to the mmio register base is missing the __iomem
annotation. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The (void *__iomem) cast is wrong. Change the target type of the
"base" pointer to void __iomem instead and drop the cast.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Casting a pointer to unsigned long only to immediately cast it back
to a pointer makes no sense. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata_dwc_qc_prep() does nothing. Use the default ata_noop_qc_prep
instead.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here we refactor HOSTDEV{P}_FROM_*() macros to fit one line and fix the
definition of HSDEV_FROM_HSDEVP() where wrong name of the parameter waas used.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This moves all global data into the driver private struct, thus
permitting multiple devices of this type to be used.
The core_scr_read/write() functions are replaced with equivalent
calls to the existing sata_dwc_scr_read/write().
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support for powering on an optional PHY when activating the
device.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently this driver only works with a DesignWare DMA engine which it
registers manually using the second "reg" address range and interrupt
number from the DT node.
This patch makes the driver instead use the "dmas" property if present,
otherwise optionally falling back on the old way so existing device
trees can continue to work.
With this change, there is no longer any reason to depend on the 460EX
machine type so drop that from Kconfig.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_qc_issue() can't handle DMA commands and thus we have to avoid it for
them. Do call ata_bmdma_qc_issue() instead for this case. Note that the former
one distinguishes PIO and DMA mode and behaves accordingly.
Suggested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Calling dmaengine_prep_slave_sg() for non-dma ATA commands is
unnecessary at best and could be harmful if the dma driver reacts
badly to this. It also causes this driver to print a bogus error
message in these cases.
This patch changes sata_dwc_qc_issue() to only do the dma setup
for dma commands and also reports an error to libata if if fails.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to have a platform driver compiled since the DMA driver is
used as a library.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In the original code the DMA is always a flow controller. Set this accordingly
in updated code.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The burst size as defined by DMAengine API is in items of address width. Derive
burst size from AHB_DMA_BRST_DFLT (64 bytes) by dividing it to
DMA_SLAVE_BUSWIDTH_4_BYTES (4 bytes) that gives us 16 items.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The original code states:
Make sure a LLI block is not created that will span 8K max FIS
boundary. If the block spans such a FIS boundary, there is a chance
that a DMA burst will cross that boundary -- this results in an error
in the host controller.
Since we have switched to generic DMAengine API we satisfy above by setting
dma_boundary value to 0x1fff.
Suggested-by: Mans Rullgard <mans@mansr.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes Machine Check "Data Write PLB Error" which happens
when libata-sff's ata_sff_dev_select is trying to write into the
device_addr in order to select a drive. However, SATA has no master
or slave devices like the old ATA Bus, therefore selecting a
different drive is kind of pointless.
Data Write PLB Error
Oops: Machine check, sig: 7 [#1]
PowerPC 44x Platform
Modules linked in:
CPU: 0 PID: 508 Comm: scsi_eh_0 Not tainted 4.6.0-rc3-next-20160412+ #10
[...]
NIP [c027e820] ata_sff_dev_select+0x3c/0x44
LR [c027e810] ata_sff_dev_select+0x2c/0x44
Call Trace:
[cec31cd0] [c027da00] ata_sff_postreset+0x40/0xb4 (unreliable)
[cec31ce0] [c027a03c] ata_eh_reset+0x5cc/0x928
[cec31d60] [c027a840] ata_eh_recover+0x330/0x10bc
[cec31df0] [c027bae0] ata_do_eh+0x4c/0xa4
[...]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull libata updates from Tejun Heo:
- ahci grew runtime power management support so that the controller can
be turned off if no devices are attached.
- sata_via isn't dead yet. It got hotplug support and more refined
workaround for certain WD drives.
- Misc cleanups. There's a merge from for-4.5-fixes to avoid confusing
conflicts in ahci PCI ID table.
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_xgene: dereferencing uninitialized pointer in probe
AHCI: Remove obsolete Intel Lewisburg SATA RAID device IDs
ata: sata_rcar: Use ARCH_RENESAS
sata_via: Implement hotplug for VT6421
sata_via: Apply WD workaround only when needed on VT6421
ahci: Add runtime PM support for the host controller
ahci: Add functions to manage runtime PM of AHCI ports
ahci: Convert driver to use modern PM hooks
ahci: Cache host controller version
scsi: Drop runtime PM usage count after host is added
scsi: Set request queue runtime PM status back to active on resume
block: Add blk_set_runtime_active()
ata: ahci_mvebu: add support for Armada 3700 variant
libata: fix unbalanced spin_lock_irqsave/spin_unlock_irq() in ata_scsi_park_show()
libata: support AHCI on OCTEON platform
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the call to acpi_get_object_info() fails then "info" hasn't been
initialized. In that situation, we already know that "version" should
be XGENE_AHCI_V1 so we don't actually need to dereference "info".
Fixes: c9802a4be6 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These PCI device IDs have been removed from the Intel Lewisburg design
specification. They are no longer needed.
Signed-off-by: Scott Lawson <scott.lawson@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HPCP bit is set by bioses for on-board sata ports either because
they think sata is hotplug capable in general or to allow Windows
to display a "device eject" icon on ports which are routed to an
external connector bracket.
However in Redhat Bugzilla #1310682, users report that with kernel 4.4,
where this bit test first appeared, a lot of partitions on sata drives
are now mounted automatically.
This patch should fix redhat and a lot of other distros which
unconditionally automount all devices which have the "removable"
bit set.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 8a3e33cf92 ("ata: ahci: find eSATA ports and flag them as removable" changes userspace behavior)
Link: http://lkml.kernel.org/g/56CF35FA.1070500@redhat.com
Cc: stable@vger.kernel.org #v4.4+
Due to Errata in ThunderX, HOST_IRQ_STAT should be
cleared before leaving the interrupt handler.
The patch attempts to satisfy the need.
Changes from V2:
- removed newfile
- code is now under CONFIG_ARM64
Changes from V1:
- Rebased on top of libata/for-4.6
- Moved ThunderX intr handler to new file
tj: Minor adjustments to comments.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, workaround for broken WD drives is applied always, slowing
down all drives. And it has a bug - it's not applied after resume.
Apply the workaround only if the error really appears
(SErr == 0x1000500). This allows unaffected drives to run at full speed
(provided that no affected drive is connected to the controller).
Also make sure the workaround is re-applied on resume.
Tested on VT6421.
As SCR registers access is known to cause problems on VT6420 (and I
don't have it to test), keep the workaround applied always on VT6420.
Unaffected drive (Hitachi HDS721680PLA380):
Before:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec
After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 200 MB in 3.01 seconds = 66.47 MB/sec
Affected drive (WDC WD5003ABYX-18WERA0):
Before:
$ hdparm -t --direct /dev/sda
/dev/sda:
Timing O_DIRECT disk reads: 180 MB in 3.02 seconds = 59.51 MB/sec
After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 156 MB in 3.03 seconds = 51.48 MB/sec
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 180 MB in 3.02 seconds = 59.64 MB/sec
The first hdparm is slower because of the error:
[ 50.408042] ata5: Incompatible drive: enabling workaround. This slows down transfer rate to ~60 MB/s
[ 50.728052] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 50.744834] ata5.00: configured for UDMA/133
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds runtime PM support for the AHCI host controller driver so
that the host controller is powered down when all SATA ports are runtime
suspended. Powering down the AHCI host controller can reduce power
consumption and possibly allow the CPU to enter lower power idle states
(S0ix) during runtime.
Runtime PM is blocked by default and needs to be unblocked from userspace
as needed (via power/* sysfs nodes).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add new functions ahci_rpm_get_port()/ahci_rpm_put_port() that change
runtime PM status of AHCI ports. Depending if the AHCI host has runtime PM
enabled or disabled calling these may trigger runtime suspend/resume of the
host controller.
We also call these functions in appropriate places to make sure host
controller registers are available before using them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In order to add support for runtime PM to the ahci driver we first need to
convert the driver to use modern non-legacy system suspend hooks. There
should be no functional changes.
tj: Updated .driver.pm init for older compilers as suggested by Andy
and Chrsitoph.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This allows sysfs nodes to read the cached value directly instead of
powering up possibly runtime suspended controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The main difference in the new Armada 3700 is that no address
decoding needs to take place in the driver probe.
[gregory.clement@free-electrons.com: reformulate the commit log]
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_scsi_park_show() was pairing spin_lock_irqsave() with
spin_unlock_irq(). As the function is always called with irq enabled,
it didn't actually break anything. Use spin_lock_irq() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Elias Oltmanns <eo@nebensachen.de>
This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The RB532 platform specific irq_to_gpio() implementation has been
removed with commit 832f5dacfa ("MIPS: Remove all the uses of
custom gpio.h"). Now the platform uses the generic stub which causes
the following error:
pata-rb532-cf pata-rb532-cf: no GPIO found for irq149
pata-rb532-cf: probe of pata-rb532-cf failed with error -2
Drop the irq_to_gpio() call and get the GPIO number from platform
data instead. After this change, the driver works again:
scsi host0: pata-rb532-cf
ata1: PATA max PIO4 irq 149
ata1.00: CFA: CF 1GB, 20080820, max MWDMA4
ata1.00: 1989792 sectors, multi 0: LBA
ata1.00: configured for PIO4
scsi 0:0:0:0: Direct-Access ATA CF 1GB 0820 PQ: 0\
ANSI: 5
sd 0:0:0:0: [sda] 1989792 512-byte logical blocks: (1.01 GB/971 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't\
support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
Fixes: 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
Cc: Alban Bedel <albeu@free.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org> #v4.3+
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OCTEON SATA controller is currently found on cn71XX devices.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Vinita Gupta <vgupta@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.
I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.
The problems with this are:
* On big-endian machines, this will always write a zero because it
stores the wrong byte into user space.
* In compat mode, the upper three bytes of the variable are updated
by the compat_hdio_ioctl() function, but they now contain
uninitialized stack data.
* The hdparm tool calling this ioctl uses a 'static long' variable
to store the result. This means at least the upper bytes are
initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
would fill them with data that remains stale when the low byte
is overwritten. Fortunately libata doesn't implement any of the
affected ioctl commands, so this would only happen when we query
both an IDE and an ATA device in the same command such as
"hdparm -N -c /dev/hda /dev/sda"
* The libata code for unknown reasons started using ATA_IOC_GET_IO32
and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
while the ioctl commands that were added later use the normal
HDIO_* names. This is harmless but rather confusing.
This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to H/W errata, the HOST_IRQ_STAT register misses the edge interrupt
when clearing the HOST_IRQ_STAT register and hardware reporting the
PORT_IRQ_STAT register happens to be at the same clock cycle.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The flexibility to override the irq handles in the LLD's are already
present, so controllers implementing a edge trigger latch can
implement their own interrupt handler inside the driver. This patch
removes the AHCI_HFLAG_EDGE_IRQ support from libahci and moves edge
irq handling to ahci_xgene.
tj: Minor update to description.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kenrel.org>
This patch implements the capability to override the generic AHCI
interrupt handler so that specific ahci drivers can implement their
own custom interrupt handler routines. It also exports
ahci_handle_port_intr so that custom irq_handler implementations can
use it.
tj: s/ahci_irq_handler/irq_handler/ and updated description.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The bulk of ATA host state machine is implemented by
ata_sff_hsm_move(). The function is called from either the interrupt
handler or, if polling, a work item. Unlike from the interrupt path,
the polling path calls the function without holding the host lock and
ata_sff_hsm_move() selectively grabs the lock.
This is completely broken. If an IRQ triggers while polling is in
progress, the two can easily race and end up accessing the hardware
and updating state machine state at the same time. This can put the
state machine in an illegal state and lead to a crash like the
following.
kernel BUG at drivers/ata/libata-sff.c:1302!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
Modules linked in:
CPU: 1 PID: 10679 Comm: syz-executor Not tainted 4.5.0-rc1+ #300
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88002bd00000 ti: ffff88002e048000 task.ti: ffff88002e048000
RIP: 0010:[<ffffffff83a83409>] [<ffffffff83a83409>] ata_sff_hsm_move+0x619/0x1c60
...
Call Trace:
<IRQ>
[<ffffffff83a84c31>] __ata_sff_port_intr+0x1e1/0x3a0 drivers/ata/libata-sff.c:1584
[<ffffffff83a85611>] ata_bmdma_port_intr+0x71/0x400 drivers/ata/libata-sff.c:2877
[< inline >] __ata_sff_interrupt drivers/ata/libata-sff.c:1629
[<ffffffff83a85bf3>] ata_bmdma_interrupt+0x253/0x580 drivers/ata/libata-sff.c:2902
[<ffffffff81479f98>] handle_irq_event_percpu+0x108/0x7e0 kernel/irq/handle.c:157
[<ffffffff8147a717>] handle_irq_event+0xa7/0x140 kernel/irq/handle.c:205
[<ffffffff81484573>] handle_edge_irq+0x1e3/0x8d0 kernel/irq/chip.c:623
[< inline >] generic_handle_irq_desc include/linux/irqdesc.h:146
[<ffffffff811a92bc>] handle_irq+0x10c/0x2a0 arch/x86/kernel/irq_64.c:78
[<ffffffff811a7e4d>] do_IRQ+0x7d/0x1a0 arch/x86/kernel/irq.c:240
[<ffffffff86653d4c>] common_interrupt+0x8c/0x8c arch/x86/entry/entry_64.S:520
<EOI>
[< inline >] rcu_lock_acquire include/linux/rcupdate.h:490
[< inline >] rcu_read_lock include/linux/rcupdate.h:874
[<ffffffff8164b4a1>] filemap_map_pages+0x131/0xba0 mm/filemap.c:2145
[< inline >] do_fault_around mm/memory.c:2943
[< inline >] do_read_fault mm/memory.c:2962
[< inline >] do_fault mm/memory.c:3133
[< inline >] handle_pte_fault mm/memory.c:3308
[< inline >] __handle_mm_fault mm/memory.c:3418
[<ffffffff816efb16>] handle_mm_fault+0x2516/0x49a0 mm/memory.c:3447
[<ffffffff8127dc16>] __do_page_fault+0x376/0x960 arch/x86/mm/fault.c:1238
[<ffffffff8127e358>] trace_do_page_fault+0xe8/0x420 arch/x86/mm/fault.c:1331
[<ffffffff8126f514>] do_async_page_fault+0x14/0xd0 arch/x86/kernel/kvm.c:264
[<ffffffff86655578>] async_page_fault+0x28/0x30 arch/x86/entry/entry_64.S:986
Fix it by ensuring that the polling path is holding the host lock
before entering ata_sff_hsm_move() so that all hardware accesses and
state updates are performed under the host lock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/g/CACT4Y+b_JsOxJu2EZyEf+mOXORc_zid5V1-pLZSroJVxyWdSpw@mail.gmail.com
Cc: stable@vger.kernel.org
