Reading the LSR clears the break, parity, frame error, and overrun bits in
the 8250 chip, but these are not being saved in all places that read the
LSR. Same goes for the MSR delta bits. Save the LSR bits off whenever the
lsr is read so they can be handled later in the receive routine. Save the
MSR bits to be handled in the modem status routine.
Also, clear the stored bits and clear the interrupt registers before
enabling interrupts, to avoid handling old values of the stored bits in the
interrupt routines.
[akpm@linux-foundation.org: clean up pre-existing code]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The initial user manuals for MPC8544/8533 had some issues with properly
documenting the device IDs for MPC8544/8533. These processors are almost
identical and both show up on the reference boards.
Fix up the quirks for PCIe support to handle MPC8533/E.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DMA blacklist checking (->ide_dma_on check probably can go now).
* Add ->atapi_dma flag checking and remove no longer needed
ns87415_ide_dma_check() from ns87415 host driver.
* Remove now needless __ide_dma_check() wrapper and symbol export.
* Check drive->autodma instead of hwif->autodma (there should be no changes in
behavior as all users of config_drive_for_dma() set both ->autodma flags).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is no need for a global inverted alpha capability since all the
application has to do is to pass '255-alpha' as the global alpha value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Cross-compilation between e.g. i386 -> 64bit could break -> work around it
[IA64] Enable early console for Ski simulator
[IA64] forbid ptrace changes psr.ri to 3
[IA64] Failure to grow RBS
[IA64] Fix processor_get_freq
[IA64] SGI Altix : fix a force_interrupt bug on altix
[IA64] Update arch/ia64/configs/* s/SLAB/SLUB/
[IA64] get back PT_IA_64_UNWIND program header
[IA64] need NOTES in vmlinux.lds.S
[IA64] make unwinder stop at last frame of the bootloader
[IA64] Clean up CPE handler registration
[IA64] Include Kconfig.preempt
[IA64] SN2 needs platform specific irq_to_vector() function.
[IA64] Use atomic64_read to read an atomic64_t.
[IA64] disable irq's and check need_resched before safe_halt
Adrian Bunk: scripts/mod/file2alias.c is compiled with HOSTCC and ensures that
kernel_ulong_t is correct, but it can't cope with different padding on
different architectures.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.
For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set. If both have TSO then this produces
an illegal combination.
The bridge device on the other hand has the correct code to
deal with this.
In fact, the same code can be used for both. So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.
In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the following needlessly global code static:
- arch_reinit_sched_domains()
- struct attr_sched_mc_power_savings
- struct attr_sched_smt_power_savings
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
BLOCK: Hide the contents of linux/bio.h if CONFIG_BLOCK=n
sysace: HDIO_GETGEO has it's own method for ages
drivers/block/cpqarray.c: better error handling and kmalloc + memset conversion to k[cz]alloc
drivers/block/cciss.c: kmalloc + memset conversion to kzalloc
Clean up duplicate includes in drivers/block/
Fix remap handling by blktrace
[PATCH] remove mm/filemap.c:file_send_actor()
gcc currently doesn't support attributes on types, so we can't use it
function pointers. This avoids some warnings on a gcc 4.3 build.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I find a function(clockevents_unregister_notifier) which is not called by
anything in tree.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
synchronize_idle() sounds like an interesting function, but we don't
actually have it, so don't prototype it. Introduced in commit
9b06e81898, in 2005.
Signed-off-by: Josh Triplett <josh@kernel.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch c5c34d4862 (tty: flush flip buffer on
ldisc input queue flush) introduces a race condition which can lead to memory
leaks.
The problem can be triggered when tcflush() is called when data are being
pushed to the line discipline driver by flush_to_ldisc().
flush_to_ldisc() releases tty->buf.lock when calling the line discipline
receive_buf function. At that poing tty_buffer_flush() kicks in and sets both
tty->buf.head and tty->buf.tail to NULL. When flush_to_ldisc() finishes, it
restores tty->buf.head but doesn't touch tty->buf.tail. This corrups the
buffer queue, and the next call to tty_buffer_request_room() will allocate a
new buffer and overwrite tty->buf.head. The previous buffer is then lost
forever without being released.
(Thanks to Laurent for the above text, for finding, disgnosing and reporting
the bug)
- Use tty->flags bits for the flush status.
- Wait for the flag to clear again before returning
- Fix the doc error noted
- Fix flush of empty queue leaving stale flushpending
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After /proc/sys rewrite it was left unused.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hide the contents of linux/bio.h if CONFIG_BLOCK=n as there shouldn't be
compiled code that uses it.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch provides more information concerning REMAP operations on block
IOs. The additional information provides clearer details at the user level,
and supports post-processing analysis in btt.
o Adds in partition remaps on the same device.
o Fixed up the remap information in DM to be in the right order
o Sent up mapped-from and mapped-to device information
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
SUNRPC: Replace flush_workqueue() with cancel_work_sync() and friends
NFS: Replace flush_scheduled_work with cancel_work_sync() and friends
SUNRPC: Don't call gss_delete_sec_context() from an rcu context
NFSv4: Don't call put_rpccred() from an rcu callback
NFS: Fix NFSv4 open stateid regressions
NFSv4: Fix a locking regression in nfs4_set_mode_locked()
NFS: Fix put_nfs_open_context
SUNRPC: Fix a race in rpciod_down()
Trivial fix: mark the buffer to hexdump as const so callers could avoid
casting their const buffers when calling print_hex_dump().
The patch is really trivial and I suggest to consider it as a fix
(it fixes GCC warnings) and push it to current tree.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove the 'u64 now' parameter from ->task_new().
( identity transformation that causes no change in functionality. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove the 'u64 now' parameter from ->put_prev_task().
( identity transformation that causes no change in functionality. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove the 'u64 now' parameter from ->pick_next_task().
( identity transformation that causes no change in functionality. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove the 'u64 now' parameter from ->dequeue_task().
( identity transformation that causes no change in functionality. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove the 'u64 now' parameter from ->enqueue_task().
( identity transformation that causes no change in functionality. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove the 'u64 now' parameter from print_cfs_rq().
( identity transformation that causes no change in functionality. )
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are two problems with balance_tasks() and how it used:
1. The variables best_prio and best_prio_seen (inherited from the old
move_tasks()) were only required to handle problems caused by the
active/expired arrays, the order in which they were processed and the
possibility that the task with the highest priority could be on either.
These issues are no longer present and the extra overhead associated
with their use is unnecessary (and possibly wrong).
2. In the absence of CONFIG_FAIR_GROUP_SCHED being set, the same
this_best_prio variable needs to be used by all scheduling classes or
there is a risk of moving too much load. E.g. if the highest priority
task on this at the beginning is a fairly low priority task and the rt
class migrates a task (during its turn) then that moved task becomes the
new highest priority task on this_rq but when the sched_fair class
initializes its copy of this_best_prio it will get the priority of the
original highest priority task as, due to the run queue locks being
held, the reschedule triggered by pull_task() will not have taken place.
This could result in inappropriate overriding of skip_for_load and
excessive load being moved.
The attached patch addresses these problems by deleting all reference to
best_prio and best_prio_seen and making this_best_prio a reference
parameter to the various functions involved.
load_balance_fair() has also been modified so that this_best_prio is
only reset (in the loop) if CONFIG_FAIR_GROUP_SCHED is set. This should
preserve the effect of helping spread groups' higher priority tasks
around the available CPUs while improving system performance when
CONFIG_FAIR_GROUP_SCHED isn't set.
Signed-off-by: Peter Williams <pwil3058@bigpond.net.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The move_tasks() function is currently multiplexed with two distinct
capabilities:
1. attempt to move a specified amount of weighted load from one run
queue to another; and
2. attempt to move a specified number of tasks from one run queue to
another.
The first of these capabilities is used in two places, load_balance()
and load_balance_idle(), and in both of these cases the return value of
move_tasks() is used purely to decide if tasks/load were moved and no
notice of the actual number of tasks moved is taken.
The second capability is used in exactly one place,
active_load_balance(), to attempt to move exactly one task and, as
before, the return value is only used as an indicator of success or failure.
This multiplexing of sched_task() was introduced, by me, as part of the
smpnice patches and was motivated by the fact that the alternative, one
function to move specified load and one to move a single task, would
have led to two functions of roughly the same complexity as the old
move_tasks() (or the new balance_tasks()). However, the new modular
design of the new CFS scheduler allows a simpler solution to be adopted
and this patch addresses that solution by:
1. adding a new function, move_one_task(), to be used by
active_load_balance(); and
2. making move_tasks() a single purpose function that tries to move a
specified weighted load and returns 1 for success and 0 for failure.
One of the consequences of these changes is that neither move_one_task()
or the new move_tasks() care how many tasks sched_class.load_balance()
moves and this enables its interface to be simplified by returning the
amount of load moved as its result and removing the load_moved pointer
from the argument list. This helps simplify the new move_tasks() and
slightly reduces the amount of work done in each of
sched_class.load_balance()'s implementations.
Further simplification, e.g. changes to balance_tasks(), are possible
but (slightly) complicated by the special needs of load_balance_fair()
so I've left them to a later patch (if this one gets accepted).
NB Since move_tasks() gets called with two run queue locks held even
small reductions in overhead are worthwhile.
[ mingo@elte.hu ]
this change also reduces code size nicely:
text data bss dec hex filename
39216 3618 24 42858 a76a sched.o.before
39173 3618 24 42815 a73f sched.o.after
Signed-off-by: Peter Williams <pwil3058@bigpond.net.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to grab the inode->i_lock atomically with the last reference put in
order to remove the open context that is being freed from the
nfsi->open_files list.
Fix by converting the kref to a standard atomic counter and then using
atomic_dec_and_lock()...
Thanks to Arnd Bergmann for pointing out the problem.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Add xt_statistic.h to the header list for usermode programs
[BNX2]: Fix suspend/resume problem.
[TG3]: Fix suspend/resume problem.
Add xt_statistic.h to the list of headers to install.
Apparently needed to build newer versions of iptables.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
[RTNETLINK]: Fix warning for !CONFIG_KMOD
[IPV4] ip_options.c: kmalloc + memset conversion to kzalloc
[DECNET]: kmalloc + memset conversion to kzalloc
[NET]: ethtool_perm_addr only has one implementation
[NET]: ethtool ops are the only way
[PPPOE]: Improve hashing function in hash_item().
[XFRM]: State selection update to use inner addresses.
[IPSEC]: Ensure that state inner family is set
[TCP]: Bidir flow must not disregard SACK blocks for lost marking
[TCP]: Fix ratehalving with bidirectional flows
[PPPOL2TP]: Add CONFIG_INET Kconfig dependency.
[NET]: Page offsets and lengths need to be __u32.
[AF_UNIX]: Make code static.
[NETFILTER]: Make nf_ct_ipv6_skip_exthdr() static.
[PKTGEN]: make get_ipsec_sa() static and non-inline
[PPPoE]: move lock_sock() in pppoe_sendmsg() to the right location
[PPPoX/E]: return ENOTTY on unknown ioctl requests
[IPV6]: ipv6_addr_type() doesn't know about RFC4193 addresses.
[NET]: Fix prio_tune() handling of root qdisc.
[NET]: Fix sch_api to properly set sch->parent on the root.
...
This adds kerneldoc to the SPI framework. The "spi_driver" and
"spi_board_info" structs were previously not described.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it a little more clear that this is the default implementation for
the setleast operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add kernel-doc entry in <linux/irq.h> for:
Warning(linux-2.6.22-git12//include/linux/irq.h:177): No description found for parameter 'last_unhandled'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add kernel-doc notation in <linux/i2c.h> for:
Warning(linux-2.6.22-git12//include/linux/i2c.h:183): No description found for parameter 'driver'
Warning(linux-2.6.22-git12//include/linux/i2c.h:183): No description found for parameter 'usage_count'
Warning(linux-2.6.22-git12//include/linux/i2c.h:183): No description found for parameter 'list'
Warning(linux-2.6.22-git12//include/linux/i2c.h:183): No description found for parameter 'released'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pure_initcall uses the same ID as core_initcall. I guess that's a typo and
it should use its own ID.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by Gustavo de Nardin <gustavodn@mandriva.com.br>, while trying to
compile xosview (http://xosview.sourceforge.net/) with upstream kernel
headers being used you get the following errors:
serialmeter.cc:48:30: error: linux/serial_reg.h: No such file or directory
serialmeter.cc: In member function 'virtual void
SerialMeter::checkResources()':
serialmeter.cc:71: error: 'UART_LSR' was not declared in this scope
serialmeter.cc:71: error: 'UART_MSR' was not declared in this scope
...
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Gustavo de Nardin <gustavodn@mandriva.com.br>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha:
In file included from kernel/notifier.c:1:
include/linux/kdebug.h:14: warning: 'struct notifier_block' declared inside parameter list
include/linux/kdebug.h:14: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/kdebug.h:15: warning: 'struct notifier_block' declared inside parameter list
kernel/notifier.c:529: error: conflicting types for 'register_die_notifier'
include/linux/kdebug.h:14: error: previous declaration of 'register_die_notifier' was here
kernel/notifier.c:533: error: conflicting types for 'register_die_notifier'
include/linux/kdebug.h:14: error: previous declaration of 'register_die_notifier' was here
kernel/notifier.c:536: error: conflicting types for 'unregister_die_notifier'
include/linux/kdebug.h:15: error: previous declaration of 'unregister_die_notifier' was here
kernel/notifier.c:539: error: conflicting types for 'unregister_die_notifier'
include/linux/kdebug.h:15: error: previous declaration of 'unregister_die_notifier' was here
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev driver doesn't currently expose all SPI communications modes to
userspace. This passes them all through to the driver.
Two of them are potentially troublesome, in the sense that they could cause
hardware conflicts on shared busses. It might be appropriate to add some
privilege checks for for those modes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loopback mode is supported by various controllers. This mode can be
useful for testing, especially in conjunction with spidev driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
