This patch allows to dump the SIM registers from debugfs. It will
temporary change the config to allow APE side to read the SIM registers.
Note that this read can cause problem on modem side since the modem
can't read these registers while the operation is ongoing.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
So we're removing support for it.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add VBUS_DET_R, VBUS_DET_F IRQ, ID_DET_PLUGR and ID_DET_PLUGF IRQ
information to ab8505_iddet_resources. These are required to get
interrupts for AB8505 cut-2.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Optimise GPADC driver:
* for code readability and maintenance by grouping similar cheking
* for performance by grouping several writing to control register
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Allow GPADC debug information to be shown when executing on an AB8540
based platform.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This patch enables the GPADC to work on AB8540 based platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add a new reset function which uses the AB WD with 0 timeout.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Make it possible to dump all registers in ab8505 and ab9540.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add error checks to see if sysctrl was probed as it should.
If the sysctrl_dev is not set the return value is -EINVAL.
Signed-off-by: Marcus Danielsson <marcus.danielsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Per FORLIN <per.forlin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add information regarding what ab interrupt that caused
a wake-up from suspend in <debugfs>/ab8500/interrupts.
Also print the name of the interrupts, not just the numbers.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Per FORLIN <per.forlin@stericsson.com>
Tested-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Stop trying to read i2c registers if one fail.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
ITSource/ITLatch 7, 8, 9 and 10 don't exist on AB8540. This patch
replaces them with '-1' in the interrupt list, and handles the '-1'
in the code accordingly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Here we're separating Battery Management devices into their own
structure, removing the common device structure & redistribute them
amongst the individual platform structs and completing the population
of them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Dump function that stores all readable ABB registers to a memory
areas where they can be accessed from dump file.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This patch changes bank prints to use hex value.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Daniel WILLERUD <daniel.willerud@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
There are missing register descriptions from the AB8505 user manual
and these need to be masked so that the APEINT line can toggle.
This patch also affects the behaviour of AB9540.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: Alexandre TORGUE <alexandre.torgue@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add the support of gpacd hw conversion and make the number of
sample configurable.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Reread the gpadc once upon failure.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
suspend/resume methods implemented to prevent suspend while the gpadc
driver is busy.
Signed-off-by: Daniel WILLERUD <daniel.willerud@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
In L9540, turn_on_status register is not updated correctly if
the device is rebooted with AC/USB charger connected. Due to
this, the device boots android instead of entering into charge
only mode. Read the AC/USB status register to detect the charger
presence and update the turn on status manually.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Rupesh KUMAR <rupesh.kumar@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Rupesh KUMAR <rupesh.kumar@stericsson.com>
Tested-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
* Updates to the ux500 cpufreq code
* Moving the u300 DMA controller driver to drivers/dma
* Moving versatile express drivers out of arch/arm for sharing with arch/arm64
* Device tree bindings for the OMAP General Purpose Memory Controller
There is a simple conflict in drivers/cpufreq/dbx500-cpufreq.c, because
the mach/id.h header and the cpu_is_u8500_family() function in it are
now gone.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=R0p0
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9.
This includes a few larger patches for GPIO on the Marvell PXA platform
and a lot of Samsung specific bug fixes, as well as a series from Arnd
to fix older build warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BbV4
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
"Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9. This includes
a few larger patches for GPIO on the Marvell PXA platform and a lot of
Samsung specific bug fixes, as well as a series from Arnd to fix older
build warnings."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
scripts/sortextable: silence script output
ARM: s3c: i2c: add platform_device forward declaration
ARM: mvebu: allow selecting mvebu without Armada XP
ARM: pick Versatile by default for !MMU
ARM: integrator: fix build with INTEGRATOR_AP off
ARM: integrator/versatile: fix NOMMU warnings
ARM: sa1100: don't warn about mach/ide.h
ARM: shmobile: fix defconfig warning on CONFIG_USB
ARM: w90x900: fix legacy assembly syntax
ARM: samsung: fix assembly syntax for new gas
ARM: disable virt_to_bus/virt_to_bus almost everywhere
ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
ARM: SAMSUNG: Silence empty switch warning in sdhci.h
ARM: msm: proc_comm_boot_wait should not be __init
arm: vt8500: Update MAINTAINERS entry for arch-vt8500
ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
ARM: S5PV210: Fix early uart output in fifo mode
...
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
o goldfish_battery:
This is Android Emulator battery driver. Originally from Google, but
Intel folks reshaped it for mainline;
o pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses AB8500
battery management core;
o qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes;
o restart-poweroff:
A generic driver that implements 'power off by restarting'. The actual
poweroff functionality is implemented through a bootloader, so Linux'
task is just to restart the box. The driver is useful on Buffalo
Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked on
submitting the driver (as well as qnap-poweroff above).
- A lot of fixes for ab8500 drivers. This is a part of efforts of syncing
internal ST-Ericsson development tree with the mainline. Lee Jones @
Linaro worked on compilation and reshaping these series;
- New health properties for the power supplies: "Watchdog timer expire"
and "Safety timer expire";
- As usual, a bunch of fixes/cleanups here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRIww1AAoJEGgI9fZJve1bJ7sP/1hR8SYQZ/k0ayxA/kIxNEDA
Qa2sAcdP5pa4F/A2Wi5MTrckSHuLlRRigWRCPM09emVOvt6g2MdM3Eq6ShuYb2p0
g2bX0F9KBEa9gdiJC1wNVe9DilXbrJsk86V5E+ZkuVnNzM3S1FA1sPWGhdH66YVq
9IKxm2XntyXFpuvhSYE01KQoFY+Crv1NEGXoIR7tB6Q1KOf3XswnsFwdKJ95IO5r
8f/lVYRAYUfeplhrYd3eJTtb/GHhK7CutFV/E6kWlumGCWNVH2xt+dTlAmTUdQvO
jKe9R5iq5eXFTQmN8QZDH7QdXO1DdmJZ9F112hIAud/93bmNrnc0WqMKM7CFHkfH
S6ptGgeIdpGEM1KMgzKTNrQeNIYsVNtqbEiIiodR8S4e0cX2pb2n5IfzmELIVc0n
QMZylORpGaH1lBxTE2RoT4raGeWF5jH0t0b0YRqccRPvQ4VjCJslDOq9IOETUe+/
YxWpELJigW7FGLMfx0SB2/3s1P4EUaufWvHANCVaPuBsOZga854R4dzms4hKyKsL
JQg+OKp/Bt78yAj/8/n0FWdxgldp/NjF4485ITQ1eOZyg8VSeIp93Lk6lgSTukux
R1xLruxfPgdynpmYFCGF99JG2G8RmRuJFSTf8JttvyztkAxQw6zBtdmdiPk38wst
qpUxdPpNDIvt65Ix7x+D
=955B
-----END PGP SIGNATURE-----
Merge tag 'for-v3.9' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
A fairly quiet release for the regulator API, the bulk of the changes
being lots of small cleanups and API updates contributed by Axel Lin
with just a small set of larger changes:
- New driver for LP8755
- DT support for S5M8767, TPS51632, TPS6507x and TPS65090
- Support for writing a "commit changes" bit in the regmap helper
functions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+3b2
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release for the regulator API, the bulk of the changes
being lots of small cleanups and API updates contributed by Axel Lin
with just a small set of larger changes:
- New driver for LP8755
- DT support for S5M8767, TPS51632, TPS6507x and TPS65090
- Support for writing a "commit changes" bit in the regmap helper
functions."
* tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (60 commits)
regulator: Fix memory garbage dev_err printout.
regulator: max77686: Reuse rdev_get_id() function.
regulator: tps51632: Use regulator_[get|set]_voltage_sel_regmap
regulator: as3711: Fix checking if no platform initialization data
regulator: s5m8767: Prevent possible NULL pointer dereference
regulator: s5m8767: Fix dev argument for devm_kzalloc and of_get_regulator_init_data
regulator: core: Optimize _regulator_do_set_voltage if voltage does not change
regulator: max8998: Let regulator core handle the case selector == old_selector
regulator: s5m8767: Use of_get_child_count()
regulator: anatop: improve precision of delay time
regulator: show state for GPIO-controlled regulators
regulator: s5m8767: Fix build in non-DT case
regulator: add device tree support for s5m8767
regulator: palmas: Remove a redundant setting for warm_reset
regulator: mc13xxx: Use of_get_child_count()
regulator: max8997: Use of_get_child_count()
regulator: tps65090: Fix using wrong dev argument for calling of_regulator_match
regulators: anatop: add set_voltage_time_sel interface
regulator: Add missing of_node_put()
regulator: tps6507x: Fix using wrong dev argument for calling of_regulator_match
...
And fix a kzalloc argument inversion bug while converting to devres.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the Watchdog Timer Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current probe aborts if any of the 3 base address registers are
disabled. On a TunnelCreek system I am working on, this resulted in the
SMBIOS and GPIO devices being removed when it couldn't read the base
address for the watchdog timer.
This patch accommodates partial population of the lpc_sch_cells array and
only aborts if all the base address registers are disabled. A max size
array is allocated and the individual device cells are added to it after
their base addresses are successfully determined. This simplifies the
code a bit by removing the need for the separate tunnelcreek cells array
and combining some of the add/remove logic.
Cc: Grant Likely <grant.likely@secretlab.ca>,
Cc: Denis Turischev <denis@compulab.co.il>,
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
da9052_i2c_fix() is only used locally, so let it be static.
Fix the following sparse warning:
drivers/mfd/da9052-i2c.c:63:5: warning: symbol 'da9052_i2c_fix' was not declared. Should it be static?
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the following sparse warnings:
drivers/mfd/syscon.c:40:15: warning: symbol 'syscon_node_to_regmap' was not declared. Should it be static?
drivers/mfd/syscon.c:56:15: warning: symbol 'syscon_regmap_lookup_by_compatible' was not declared. Should it be static?
drivers/mfd/syscon.c:72:15: warning: symbol 'syscon_regmap_lookup_by_phandle' was not declared. Should it be static?
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 8a6aaa3 (mfd: twl-core: Collect global variables behind one
private structure (global)) removed the variable "inuse" that is used
to determine if the device has been initialised and now use the
twl_priv structure instead. This is causing the kernel to panic on
OMAP3+ devices using the twl driver, because we try to access the
twl_priv->ready member before checking if twl_priv is initialised. Fix
this and move this test to the beginning of the twl_i2c_read/write
function because twl_get_last_module() also uses the twl_priv structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.
In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When compiling the AB8500 core driver in the latest
MFD tree the following happens:
CC drivers/mfd/ab8500-debugfs.o
/home/elinwal/linux-next/drivers/mfd/ab8500-debugfs.c:157:3: error: 'AB8500_SYS_CTRL1_BLOCK' undeclared here (not in a function)
/home/elinwal/linux-next/drivers/mfd/ab8500-debugfs.c:157:2: error: array index in initializer not of integer type
/home/elinwal/linux-next/drivers/mfd/ab8500-debugfs.c:157:2: error: (near initialization for 'debug_ranges')
(...)
This is due to a missing include statement, so fix
it up.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A lot of mfd drivers select MFD_CORE which however depends on
GENERIC_HARDIRQS support.
So add the missing dependency to all drivers to get rid of
this link error:
ERROR: "irq_create_mapping" [drivers/mfd/mfd-core.ko] undefined!
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
update onkey driver's irq base, it should get from max8925,
but not save in a private value
Signed-off-by: Qing Xu <qingx@marvell.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
we encounter rtc/power/touch driver registry failure, root cause
it is resources confilict in insert_resouce, solved by changing
mfd_add_devices 5th parameter to NULL
Signed-off-by: Qing Xu <qingx@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add irqdomains for max8925's main irq, wrap irq register operations
into irqdomain's map func. it is necessary for dt support.
Also, add dt support for max8925 driver.
Signed-off-by: Qing Xu <qingx@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The vexpress_sysreg_init() is a core_initcall() already and it can
trigger the early initialisation if a matching node is found. This patch
allows the SoC code to avoid calling vexpress_sysreg_of_early_init()
explicitly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Support new model RTS5227.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implement different ways of selecting driving capability(a necessary adjustment
along with voltage change). It was origionally in device-independent
mmc/host/rtsx_pci_sdmmc.c. Moving it here to support devices which may have a
different way of adjustment.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The LEDs on the Versatile Express motherboard are controlled
through simple memory-mapped register. This patch extends
the pseudo-GPIO controller definition for these lines and
creates generic "leds-gpio" device using them
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We are using a generic abx500 hwmon layer, so rename specific ab8500 to generic
abx500 for hwmon device and driver matching.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. Schedule card detect work at the end of the ISR
2. Callback function ops->cd_deglitch may delay for a period of time.
It is not proper to call this callback when local irq disabled.
3. Card detect flow can't be executed in parallel with other card reader
operations, so it's better to be protected by mutex.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In function rtsx_pci_switch_clock, some variables, such as min_n, max_n,
and max_div, are not necessary. And those assigned values look very
obscure for others. It's more proper to use macro definitions here to
replace these variables.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Realtek PCIe card reader only supports 32bit DMA.
This declaration can improve the readability.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In function rtsx_pci_add_sg_tbl, the statement "ptr++" is useless.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65090 mfd driver implement the suspend/resume callbacks
which just disable and enable irqs in suspend/resume respectively.
This operation is already done in irq suspend and irq_resume and
hence it is not require to implement the same in the driver.
Remove this non-require code.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When device is get added through DT then irq_base is 0 (zero)
and in this case regmap_irq_chip_get_base() generates warning.
The interrupt of this device get added through irq_domain_add_linear()
when irq_base is 0.
Hence pass the irq domain in place of base_irq when calling
mfd_add_devices().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add device tree support for the TI PMIC TPS65090.
The device can be registered through platform or DT.
Add device tree binding document for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add device tree based initialization support for TI's
tps6507x mfd device.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
devm_* functions are device managed and make error handling
and code simpler; it also fix error exit paths
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the necessary structures to use the watchdog
functionality of PRCMU.
The watchdog driver is named ux500_wdt.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add EXPORT_SYMBOL to db500_prcmu_*_a9wdog functions to allow usage from
module.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In ICH5 and earlier the GPIOBASE and GPIOCTRL registers are found at
offsets 0x58 and 0x5C, respectively. This patch allows GPIO access to
properly be enabled (and disabled) for these chipsets.
Signed-off-by: Agócs Pál <agocs.pal.86@gmail.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl_i2c_read/write_u8 become as a simple wrapper over the twl_i2c_read/write.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the regmap conversion there is no longeer a need to allocate bigger
buffer for writes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Gather the global variables under a single structure and allocate it with
devm_kzalloc(). It is easier to see them and if in the future we try to add
support for multiple instance of twl in the system it is going to be much
simpler.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can fail earlier in case multiple instance of the twl-core is tried to
be loaded.
The twl-core by design only supports one instance.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When booted with DT we can manage without the dummy pdata.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is really no point to retry to add children devices in case the
of_platform_populate() fails.
We do not have any information provided via pdata in this case anyways.
Depending on the boot type (legacy or DT) only execute either one.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
At boot time we can allocate the twl_modules array dynamically based on the
twl class we are using with devm_kzalloc() instead of the static
twl_modules[] array.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of using SUB_CHIP_ID* or magic numbers use the twl_mapping table to
look for the subchip ID.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The module id table no longer can have invalid/unused entries.
No need for checking the ID for validity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use enums for all module definitions:
twl_module_ids for common functionality among twl4030/twl6030
twl4030_module_ids for twl4030 specific ids
twl6030_module_ids for twl6030 specific ids
In this way the list can be managed easier when new functionality going to
be implemented.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the MICBIAS voltages and other attributes to be configured by the
platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the mixer is underclocked it will drop a sample so log that error
more directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Runtime power management does not function during system suspend but the
Arizona devices need to use runtime power management to power up the device
in order to handle interrupts. Try to avoid interrupts firing during
resume by disabling the primary IRQ before interrupts are reenabled on
resume and only reenabling it again during main resume.
The goal is to avoid issues in the situation where an interrupt is asserted
during resume (eg, due to it being the wake source) and the interrupt
handling gets scheduled prior to the device being able to handle runtime
PM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM5102 register defaults are not up to date with the current register
map, synchronise them with those for current devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can cache some of them but this is simpler for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The latest evaluation of the revision B silicon suggests some changes to
the tuning applied for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Not strictly required as probe deferral will take care of everything but
it makes boot a little smoother.
Reported-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since regmap sometimes uses volatile as a proxy for readable simply
having a blanket condition can mark too many registers as readable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Palma RTC is capable of generating alarm interrupt. Pass the alarm interrupt
as IRQ_RESOURCE for palmas-rtc sub device driver so that rtc driver can get
irq as platform_get_irq().
Also pass the irq domain in mfd_add_devices() to properly offset the irqs for
sub devices. This is needed when adding device through DT.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes the below build warning when driver is built-in.
drivers/mfd/omap-usb-host.c:750:12: warning:
‘usbhs_omap_remove’ defined but not used [-Wunused-function]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
clk_set_parent is expected to fail on OMAP3 platforms. We don't
consider that as fatal so don't spam console.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
We split initializing revision 1 and revision 2 into different
functions. Initialization is now done dynamically so that only
the number of ports available on the system are initialized.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The driver does not have an interrupt handler and
we don't really need a spinlock, so get rid of it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Enable the optional HSIC clocks (60MHz and 480MHz) for the ports
that are configured in HSIC mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
All ports have similarly named port clocks so we can
bunch them into a port data structure and use for loop
to enable/disable the clocks.
Dynamically allocate and get clocks based on number of ports
available on the platform
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Both OMAP4 and 5 exhibit the same revision ID in the REVISION register
but they have different number of ports i.e. 2 and 3 respectively.
So we can't rely on REVISION register for number of ports on OMAP5
and depend on platform data (or device tree) instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Use devm_ variants of kzalloc and ioremap. Also clean up error path.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Get rid of the unnecessary missing platform data checks
in runtime_suspend/resume. We are already checking for missing
platform data in probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The TLL module on OMAP5 has 3 channels.
HSIC mode requires the TLL channel to be in Transparent UTMI mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Get rid of the unnecessary spin_lock_irqsave/restore() as there is
no interrupt handler for this driver. Instead we serialize access
to tll_dev using a global spinlock.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
omap_enable/disable_tll() can fail if TLL device is not
initialized. It could be due to multiple reasons and not only
due to missing platform data.
Also make local variables static and use 'struct device *'
instead of 'struct platform_device *' for global reference.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
No need to check for missing platform data in runtime_suspend/resume
as it makes more sense to do it in the probe function.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This is a handy macro to check if the port requires the
USB TLL module or not. Use it to Enable the TLL module and manage
the clocks.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Every channel has a functional clock that is similarly named.
It makes sense to use a for loop to manage these clocks as OMAPs
can come with up to 3 channels.
Dynamically allocate and get channel clocks depending on the
number of clocks avaiable on the platform.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use devm_ variants of kzalloc() and ioremap(). Simplify the error path.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Fix channel count detecion for REV2. Also, don't give up
if we don't recognize the IP Revision. We assume the default
number of channels (i.e. 3) for unrecognized IPs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Let's have a single platform data structure for the OMAP's High-Speed
USB host subsystem instead of having 3 separate ones i.e. one for
board data, one for USB Host (UHH) module and one for USB-TLL module.
This makes the code much simpler and avoids creating multiple copies of
platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
For the ehci-omap.c part:
Acked-by: Alan Stern <stern@rowland.harvard.edu>
This is a branch of fixes that originally were scheduled for 3.8 but
due to the request from Linus to hold back on all but the most critical
of fixes, we're re-queueing them for 3.9 here.
* fixes-for-3.9:
ARM: dts: imx6: fix fec ptp clock slow 10 time
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
ARM: at91/at91sam9x5.dtsi: fix usart3 TXD
ARM: at91: at91sam9x5: fix usart3 pinctrl name
ARM: EXYNOS: Fix crash on soft reset on EXYNOS5440
ARM: dts: fix tick and alarm irq numbers for exynos5440
ARM: dts: fix compatible value for exynos pinctrl
ARM: dts: Fix compatible value of pinctrl module on EXYNOS5440
ARM: S3C24XX: fix uninitialized variable warning
mfd/vexpress: vexpress_sysreg_setup must not be __init
ARM: ux500: Fix u9540 booting issues
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
ARM: ux500: add spin_unlock(&master_lock).
ARM: ux500: Disable Power Supply and Battery Management by default
Signed-off-by: Olof Johansson <olof@lixom.net>
When trying to get rid of the cross-includes of <mach/id.h>
from different drivers, so we can localize ASIC/CPU detection
to the mach-ux500 folder, we run into the way the PRCMU
handles base addresses and firmware detection.
This patch updates the firmware version detection to pass
the required information as platform data instead of
relying on cpu_is_* macros.
Now the PRCMU base address, the secondary TCDM area, the
TCPM area and the IRQ are passed as resources instead of
being grabbed from <mach/*> files. Incidentally this also
removes part of the reliance on <mach/irqs.h>.
Further it updates the firmware version detection, since the
location of the firmware ID bytes in the designated memory
are is now passed from the platform data instead. There is
no reason not to include the nice split-off of a struct to
hold the firmware information and a separate function to
populate it.
The patch actually rids the need to use the external
db8500_prcmu_early_init call at all, but I'm keepin back
that removal as I don't want the patch to be too big.
Cc: arm@kernel.org
Cc: Michel Jaoen <michel.jaouen@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Loic Pallardy <loic.pallardy@stericsson.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old AB8500 GPIO driver has been un-BROKEN and converted into a
multi-platform pinctrl driver. If any AB9540 based devices wish to
request any GPIO pins that it offers, they can after this patch.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old, BROKEN AB8500 GPIO driver has been revamped as a shiny
new pinctrl driver and has been renamed as such. So, if we would
like to make use of it, we need to register it via its new name.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the AB8500 IRQ mask and unmask functions, we rely on testing for
IRQ_TYPE_EDGE_RISING and IRQ_TYPE_EDGE_FALLING interrupts to
physically mask and unmask the correct interrupt lines. In order
for us to do that, the trigger needs to be set in the associated
flags. However, unless a irq_set_type() function pointer is passed
when registering the IRQ chip, the IRQ subsystem will refuse to do
it. For that reason, we're providing one.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch:
"mfd: ab8500: prepare to handle AB8500 GPIO's IRQs correctly"
altered the AB8500 IRQ mask/unmask functions such that they
would handle masking on/off the falling edge IRQ if this was
requested by the consumer. However the bit mask for hwirqs
43 and 44 was shifting the bit mask incorrectly, resulting in
the wrong IRQ being mased/unmasked.
Further while the patch would mask/unmask the correct line,
when the interrupt actually came in, it would still be treated
as a valid hwirq. The offsetting applied when masking/unmasking
was not applied when handling the IRQ, i.e. the falling edge
lines were not routed back to the rising edge lines.
This fixes both cases. The end result has been tested with
the SIM detect IRQ, GPIO12, hwirq 46 and 62.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
In an upcoming patch, the gpio-ab8500 driver will relinquish all
IRQ handling capability and pass it back into the AB8500 core
driver. This will aid in reducing massive code duplication within
the kernel. Also, most of the functionality is already in the
AB8500 core driver, as the GPIO IRQs are actually sandwiched
between lots of other IRQs which the core driver already handles.
All we're doing here is providing the core driver with knowledge
that each GPIO has two IRQs assigned to it; one for rising and
a separate one for falling.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix drift in DT parsing function name in the stub code.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The new format of ab8500_gpadc_get() accepts a device name as a
parameter to specify which device to retrieve. This patch
enforces the use of that new format.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
The ab8500_gpadc structure carries lots of important information which
most functions make good use of. The initial expectation was that
ab8500_gpadc_runtime_idle() would be no exception; however, this hasn't
been the case to date. Let's remove it for now and add it back in only
when we have a use for it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reduce the conversion timeout from 2s to 0.5s
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Simple pointer error fix to obtain the expected sizeof() result.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ashok G <ashok.g@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Add runtime pm support to speed up multiple ADC reads in a row.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
This patch adds an entry in debugfs to check number of interrupts
from the AB.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
Add support for AB8505 and AB9540
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
With the introduction of new AB* platforms, it's important to allow
as much code reuse as possible. By allowing a system's number of IRQs
to be dynamically passed, we can reuse almost all of the -debugfs
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Implement an API so that a user may dump all AB8500 registers
via debugfs file access.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Update the ab8500_registers_print() to reuse it from multiple places.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
In case of AB-V3, the eye diagram related issues are resolved.
So, set the device charging current to 300mA when connected to
standard host. Also, add the USB PHY tuning values to improve
the USB eye diagram
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: <thirupathi.chippakurthy@stericsson.com>
Allow a user to take a glimpse into the inner workings of the
AB8500 Analogue-to-Digital Converters, via debugfs.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Add debugfs entry ab8500/hwreg to read/write bit-field in AB8500 registers.
Check the debugfs entries usage from heading comments in ab8500-debugfs.c
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: carriere etienne <etienne.carriere@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Partly for coding style reasons, but mostly because sparse warns on it.
This patch is a completion of a previous patch by Mark Brown.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a counter to the sysfs file dynamically created
by debugfs. It also fixes an array index error.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Some drivers can detect subsystem failures e.g. shared memory driver
can detect modem sub system failures. It would be helpful in analyzing
these failures if AB register dump is available at that point. This
patch adds the API for the drivers to dump AB registers in the kernel
log.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Export ab8500_sysctrl_read() and ab8500_sysctrl_write() symobols.
They will be used by LTP test cases.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Add the possibility to pass configuration settings for
SysCl1kReqRfClkBuf to SysClk8ReqRfClkBuf via platform data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kennet Wallden <kennet.wallden@stericsson.com>
Reviewed-by: Karl-Johan PERNTZ <karl-johan.perntz@stericsson.com>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
The resolution of msleep is related to HZ, so with HZ set to
100 any msleep of less than 10ms will become ~10ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's possible to supply a string to provide a reason for
triggering a restart. In this case our reason is to enter
charging-only mode, as a charger was found to be present.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
When a charger is connected, we usually want AB8500 based systems to
reboot into charging-only mode. However, if the battery type cannot
be identified this would be futile, so we'll just shut the system
down instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
If a charger is attached on power off, reboot the system
into charging mode instead of powering it off.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
The kernel allows us to specify a function call-back which will be
invoked when a system power-off request has been received. Here we
provide one which is to be used when shutting down AB8500 based
platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
* Move sp810 header to a more generic location,
mainly to share it with arm64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCULAAAoJEL9jRaJfXa5PyysH/AsFbihoAGU0S7o+ggyN4S8m
5myEfbdMvgI5Hjcl/MgcVJAl6jFpDjmBH5ZPu+o8WzoP5L91C9F//kMRZqK0zATj
Y2OdMVNfVQG94bSsmjHryWF8W0RYcY2bQr0wJmgguNDpRLFsFdF3Rb58AWzG+2tP
KFxDg9u/CyhC/sv7BzoKI+J3ol5wEmv4BNMbPyjYG8L5TcBfe/IZqnl6KZ/QAw5i
QUFs3oXtT4/v8bnsxAym+VXIvjSHWs2t0CivfMyH+ZIgb3NbfJ1gIOCOJIk5XWTu
6L1yYyBBcRr60y9p4s2Nd4NxHZEB7pyZYuboUOxSmRNnEM54RT2Nkvcdon8j6Rw=
=uB7w
-----END PGP SIGNATURE-----
Merge tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux into next/drivers
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zjvx
-----END PGP SIGNATURE-----
Merge tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
From Linus Walleij:
Removal of the <mach/id.h> include from ux500
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
* tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: de-globalize <mach/id.h>
ARM: ux500: Introduce cpu_is_u8580()
mfd: prcmu: delete pin control helpers
Signed-off-by: Olof Johansson <olof@lixom.net>
This removes the file <mach/id.h> from the global kernel include
scope, making it a pure mach-ux500 detail. All ASIC specifics
needed by drivers shall henceforth be passed from either platform
data or the device tree.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch 52666298a 'mfd: vexpress-sysreg: Don't skip initialization
on probe' adds a call to vexpress_sysreg_setup from a non-__init
function, so this also has to lose its __init annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: arm@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
* depends/cleanup: (375 commits)
ARM: at91: fix board-rm9200-dt after sys_timer conversion
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
timer: vt8500: Move timer code to drivers/clocksource
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
...
We have some build failure fixes (twl4030, vexpress, abx500 and tps65910),
some actual runtime oops and lockup fixes (rtsx, da9052), and some more
hypothetical NULL pointers dereferences fixes for pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output voltage
and clock divider correctness for rtl8411 (rtsx driver), and irqdomain fix for
db8550-prcmu, and some more cosmetic fixes for arizona and wm5102.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRBIBuAAoJEIqAPN1PVmxKCZYP/3EP7I6nTnHfmMJHr6KhL9F8
h/PFzSJiYC5DHoYpvcD6ESkDtqgZTOgt/R8VzbzcfCoSAlARCyo3WenCjUhREspW
2vCb+rVqBXc3+pn/Hed5WlTx3a231iSYiQd4OMbDkG22TuTKdf4GOWcl4KnAVMjp
NMqD3wCkDeMkutxRO7eWc+B/eXmYDp38abiYU+xJCMfmpvRwiPp7/RQTw/9kHgF/
VHGqzH91YPJmcF9OcDDzsvJ2zGwPsXPhtsOnwxL7KkjI4WM4EZv8Nr0NwTsuIgNJ
liqs4QO1XpTF+bAPKW/aT4VVLxYmLrzVao+bg6A9Vn5Q6Wt+N4McectvN7yndfOQ
GuSPI+LqcZvDEHaKGybRFdsbN+sh95f7Qz6dbFedJ3nWBhlFd7YiXgkQF3Yg38sX
rbK66F0PuH7F010a3cbhZ4jsHUb1MxzU6YSCLwUvukF1ijitPP89md0K9YaN9cbT
YbBdZpphaiFePz9CjRyyYJvo4DC9i9BTgC8Ac3qiG1TELhb/Dl064d4o0oDDEfzH
qVo21yUWeJ9jsHMnFvJuaDe9IbfxyDWJSLXFPlwaW/1qdbDPKzCr1Sro4v+lmOh5
1RIiHfu52RSPDewo0ACZPPOd8h8/Jfra37CDiGPGnjbEkUJTxC7XfHie6M9034ov
m/ORqHJOi6Wh9Iy7YHM3
=rxug
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the twl4030_write_script function gets called with
a zero length argument, its return value does not
get set. We know that all scripts have a nonzero
length, but returning an error in case they ever
do is probably appropriate.
Without this patch, building omap2plus_defconfig results in:
drivers/mfd/twl4030-power.c: In function 'load_twl4030_script':
drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: "Kristo, Tero" <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
If charging is started before USB enumeration of an Accessory
Charger Adapter has finished, the AB8500 will generate a
VBUS_ERROR. This in turn results in timeouts and delays the
enumeration with around 15 seconds. This patch delays the
charging and then ramps currents slowly to avoid VBUS errors.
The delay allows the enumeration to have finished before
charging is turned on.
Signed-off-by: Martin Sjoblom <martin.w.sjoblom@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Compiling vexpress client drivers as module results in error messages such as
ERROR: "__vexpress_config_func_get" [drivers/hwmon/vexpress.ko] undefined!
ERROR: "vexpress_config_func_put" [drivers/hwmon/vexpress.ko] undefined!
This is because the global functions in drivers/mfd/vexpress-config.c are not
exported. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the control bus is unrelabile we may hit errors during regcache_sync(),
especially given that it tends to be one the most dense bursts of I/O in
many systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes a regression in the TC3589x driver introduced in
commit 15e27b1088
"mfd: Provide the tc3589x with its own IRQ domain"
If a system with a TC3589x expander is booted and a base
IRQ is passed from platform data, a legacy domain will
be used. However, since the Ux500 is now switched to use
SPARSE_IRQ, no descriptors get allocated on-the-fly,
and we get a crash.
Fix this by switching to using the simple irqdomain that
will handle this uniformly and also allocates descriptors
explicitly.
Also fix two small whitespace errors in the vicinity while
we're at it.
Cc: stable@kernel.org
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses pcf->dev in the dev_err call before setting it to
&client->dev. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses max77693->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
This patch also includes below cleanups:
- Move checking pdata earlier and show dev_err if no platform data found.
- Remove unnecessary err_regmap goto label.
- Unregister i2c devices if regmap init for muic fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code uses max77686->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes two issues with the DB8500 PRCMU irqdomain:
- You have to state the irq base 0 to get a linear domain
for the DT case from irq_domain_add_simple()
- The irqdomain was not used to translate the initial irq
request using irq_create_mapping() making the linear
case fail as it was lacking a proper descriptor.
I took this opportunity to fix two lines of whitespace
errors in related code as I was anyway messing around with
it.
Cc: stable@kernel.org
Acked-by Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65910 mfd driver uses functions that are only avaiable when
REGMAP_IRQ is enabled. So "select REGMAP_IRQ" is added to mfd
Kconfig to fix below build error:
drivers/built-in.o: In function `tps65910_irq_exit':
/media/anil/kernel/drivers/mfd/tps65910.c:265: undefined reference to `regmap_del_irq_chip'
drivers/built-in.o: In function `tps65910_irq_init':
/media/anil/kernel/drivers/mfd/tps65910.c:254: undefined reference to `regmap_add_irq_chip'
drivers/built-in.o: In function `tps65910_i2c_probe':
/media/anil/kernel/drivers/mfd/tps65910.c:509: undefined reference to `regmap_irq_get_domain'
make: *** [vmlinux] Error 1
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than disabling the error reporting only for earlier revisions
unconditionally disable it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This brings in all of the mei and other fixes that are needed to continue
development in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build error:
drivers/built-in.o: In function `twl_probe':
drivers/mfd/twl-core.c:1256: undefined reference to `devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[ Samuel is busy, taking it directly - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Since the cpufreq driver for ux500 has been renamed from
cpufreq-db8500 to cpufreq-dbx500, we need to change the
device name here as well.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4g/i
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really."
There was some concern about commit 68136b10 ("RM: sunxi: Change device
tree naming scheme for sunxi"), but Tony says:
"Looks like that's trivial to fix as needed, no need to rebuild the
branch to fix that AFAIK.
The fix can be done once Olof is available online again.
Linus, I suggest that you go ahead and pull this if there are no other
issues with this branch."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: sunxi: Change device tree naming scheme for sunxi
ARM: ux500: fix missing include
ARM: u300: delete custom pin hog code
ARM: davinci: fix build break due to missing include
ARM: exynos: Fix warning due to missing 'inline' in stub
ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
ARM: dts: mx27: Fix the AIPI bus for FEC
ARM: OMAP2+: common: remove use of vram
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
...
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8+P4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
These patches fixes a build error caused by a merge
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.
* tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: common: remove use of vram
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
mfd: omap-usb-host: get rid of cpu_is_omap..() macros
ARM: OMAP: Remove debug-devices.c
ARM: OMAP2420: Fix ethernet support for OMAP2420 H4
OMAP2+: mux: Fixed gpio mux mode analysis
OMAP: board-files: fix i2c_bus for tfp410
ARM: OMAP2+: Fix sparse warnings in timer.c
ARM: AM335x: Fix warning in timer.c
ARM: OMAP2+: Fix realtime_counter_init warning in timer.c
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.
The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace the
proprietary Nokia BME stack;
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks to
Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers;
- Random fixups and enhancements for a bunch of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Bb5O
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
A fairly quiet release again, a couple of relatively small new features
and a bunch of driver specific work including yet more code elimination
and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM vexpress.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2d65
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release again, a couple of relatively small new
features and a bunch of driver specific work including yet more code
elimination and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM
vexpress."
Fix up trivial conflict (due to typo fix) in palmas-regulator.c
* tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (80 commits)
regulator: core: Fix logic to determinate if regulator can change voltage
regulator: s5m8767: Fix to work even if no DVS gpio present
regulator: s5m8767: Fix to read the first DVS register.
regulator: s5m8767: Fix to work when platform registers less regulators
regulator: gpio-regulator: gpio_set_value should use cansleep
regulator: gpio-regulator: Fix logical error in for() loop
regulator: anatop: Use regulator_[get|set]_voltage_sel_regmap
regulator: anatop: Use linear_min_sel with linear mapping
regulator: max1586: Implement get_voltage_sel callback
regulator: lp8788-buck: Kill _gpio_request function
regulator: tps80031: Convert tps80031_ldo_ops to linear_min_sel and list_voltage_linear
regulator: lp8788-ldo: Remove val array in lp8788_config_ldo_enable_mode
regulator: gpio-regulator: Add ifdef CONFIG_OF guard for regulator_gpio_of_match
regulator: palmas: Convert palmas_ops_smps to regulator_[get|set]_voltage_sel_regmap
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
regulators: add regulator_can_change_voltage() function
regulator: tps51632: Ensure [base|max]_voltage_uV pdata settings are valid
regulator: wm831x-dcdc: Add MODULE_ALIAS for wm831x-boostp
regulator: wm831x-dcdc: Ensure selected voltage falls within requested range
regulator: tps51632: Use linear_min_sel and regulator_[map|list]_voltage_linear
...
This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=IIsz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is
not quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq. note
that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UJlh
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's also
taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YMKB
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Here is the "big" char/misc driver patches for 3.8-rc1. I'm starting to
put random driver subsystems that I had previously sent you through the
driver-core tree in this tree, as it makes more sense to do so.
Nothing major here, the various __dev* removals, some mei driver
updates, and other random driver-specific things from the different
maintainers and developers.
Note, some MFD drivers got added through this tree, and they are also
coming in through the "real" MFD tree as well, due to some major
mis-communication between me and the different developers. If you have
any merge conflicts, take the ones from the MFD tree, not these ones,
sorry about that.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHj7AACgkQMUfUDdst+ym7pQCgxhFDGQRJimG+Ddag+ghfLhQh
Ql0AoJsWVFvQjb7q1NO7OvOABaxjEJdu
=na5b
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver patches for 3.8-rc1. I'm starting
to put random driver subsystems that I had previously sent you through
the driver-core tree in this tree, as it makes more sense to do so.
Nothing major here, the various __dev* removals, some mei driver
updates, and other random driver-specific things from the different
maintainers and developers.
Note, some MFD drivers got added through this tree, and they are also
coming in through the "real" MFD tree as well, due to some major
mis-communication between me and the different developers. If you
have any merge conflicts, take the ones from the MFD tree, not these
ones, sorry about that.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflict in drivers/mmc/host/Kconfig due to new drivers
having been added (both at the end, as usual..)
* tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (84 commits)
MAINTAINERS: remove drivers/staging/hv/
misc/st_kim: Free resources in the error path of probe()
drivers/char: for hpet, add count checking, and ~0UL instead of -1
w1-gpio: Simplify & get rid of defines
w1-gpio: Pinctrl-fy
extcon: remove use of __devexit_p
extcon: remove use of __devinit
extcon: remove use of __devexit
drivers: uio: Only allocate new private data when probing device tree node
drivers: uio_dmem_genirq: Allow partial success when opening device
drivers: uio_dmem_genirq: Don't use DMA_ERROR_CODE to indicate unmapped regions
drivers: uio_dmem_genirq: Don't mix address spaces for dynamic region vaddr
uio: remove use of __devexit
uio: remove use of __devinitdata
uio: remove use of __devinit
uio: remove use of __devexit_p
char: remove use of __devexit
char: remove use of __devinitconst
char: remove use of __devinitdata
char: remove use of __devinit
...
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2XeO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
fixes for existing platforms as well as new ports for some ARM
platforms. In addition there are new clk drivers for audio devices and
MFDs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GoXf
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Mike Turquette:
"The common clock framework changes for 3.8 are comprised of lots of
fixes for existing platforms as well as new ports for some ARM
platforms. In addition there are new clk drivers for audio devices
and MFDs."
Fix up trivial conflict in <linux/clk-provider.h> (removal of 'inline'
clashing with return type fixes)
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (51 commits)
MAINTAINERS: bad email address for Mike Turquette
clk: introduce optional disable_unused callback
clk: ux500: fix bit error
clk: clock multiplexers may register out of order
clk: ux500: Initial support for abx500 clock driver
CLK: SPEAr: Remove unused dummy apb_pclk
CLK: SPEAr: Correct index scanning done for clock synths
CLK: SPEAr: Update clock rate table
CLK: SPEAr: Add missing clocks
CLK: SPEAr: Set CLK_SET_RATE_PARENT for few clocks
CLK: SPEAr13xx: fix parent names of multiple clocks
CLK: SPEAr13xx: Fix mux clock names
CLK: SPEAr: Fix dev_id & con_id for multiple clocks
clk: move IM-PD1 clocks to drivers/clk
clk: make ICST driver handle the VCO registers
clk: add GPLv2 headers to the Versatile clock files
clk: mxs: Use a better name for the USB PHY clock
clk: spear: Add stub functions for spear3[0|1|2]0_clk_init()
CLK: clk-twl6040: fix return value check in twl6040_clk_probe()
clk: ux500: Register nomadik keypad clock lookups for u8500
...
Currently the AB8500 battery management subsystem receives platform
specific information via two different means depending on how the
platform is booted. If DT is not enabled, a reference to a *_bm_data
data structure containing each platform specific attribute is passed
though platform_data. However, if DT is enabled, then platform_data
is empty and the reference is gained though a DT specific probe
function. There are two issues here 1) the same reference is
being collected each time and 2) the DT way doesn't allow any
provisions to select different platform specific attributes, which
kind of defeats the object.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch extends existing DT support for stmpe devices. This updates:
- missing header files in stmpe.c
- stmpe_of_probe() with pwm, rotator and new bindings.
- Bindings are updated in binding document.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
