Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down. Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.
Don't bother arming to tx hang detection when link is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a recent fix to e1000 (commit 15b2bee2) caused KVM/QEMU/VMware based
virtualized e1000 interfaces to begin failing when resetting.
This is because the driver in a virtual environment doesn't
get to run instructions *AT ALL* when an interrupt is asserted.
The interrupt code runs immediately and this recent bug fix
allows an interrupt to be possible when the interrupt handler
will reject it (due to the new code), when being called from
any path in the driver that holds the E1000_RESETTING flag.
the driver should use the __E1000_DOWN flag instead of the
__E1000_RESETTING flag to prevent interrupt execution
while reconfiguring the hardware.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded.
This apparently confused *some* versions of networkmanager.
Andy tested this for e1000e and confirmed it was working for him.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the e1000 transmit cleanup inner loop exited early, then
cleaned might not be true. This could cause tx hangs or other
badness. Use count to track the total number of descriptors
cleaned instead of basing a tx queue restart off of a temporary
working state variable.
This code now makes the flow the same for e1000/e1000e/igb/ixgbe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent e1000 from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate e1000_shutdown() from e1000_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e1000 (and e1000e, igb, ixgbe, ixgb) all do a series of
operations each time a multicast address is added. The flow goes
something like
1) stack adds one multicast address
2) stack passes whole current list of unicast and multicast
addresses to driver
3) driver clears entire list in hardware
4) driver programs each multicast address using iomem in a loop
This was causing multicast packets to be lost during the
reprogramming process.
reference with test program:
http://kerneltrap.org/mailarchive/linux-netdev/2009/3/14/5160514/thread
Thanks to Dave Boutcher for his report and test program.
This driver fix prepares an array all at once in memory and
programs it in one shot to the hardware, not requiring an "erase"
cycle.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is in regards to
http://bugzilla.kernel.org/show_bug.cgi?id=12876
where it appears that e1000 can leave its interrupt enabled after
exiting the driver. Fix the bug by making the interrupt enable
paths more aware of the driver exiting.
Thanks to Alan Cox for the poke and initial investigation.
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx cleanup routine was stopping after 64 packets and this was causing
issues resulting in the ring not being completely cleaned.
This change updates the driver to clean the entire ring and if it doesn't
it then will retry on the next pass.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the dma mapping to better support
skb_dma_map/skb_dma_unmap and addresses and redefines the tx hang logic to
be based off of time stamp instead of if the dma field is populated
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in reference to the issue shown in kerneloops (search e1000 unmap)
The e1000 transmit code was calling pci_unmap_page on dma handles that it
might have called pci_map_single on.
Same bug as e1000e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the unused macro PAGE_USE_COUNT(), since there is no more reference
to it. The last reference was removed by Jesse's commit number
630b25cdf4.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On machine were no IO ports are assigned the call
to pci_enable_device() will fail, even if need_ioport
is false, we need to use pci_enable_device_mem() here.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A nasty bug was found where an MTU change (or anything else that caused a
reset) could race with the interrupt code. The interrupt code was entered
by a shared interrupt during the MTU change.
This change prevents the interrupt code from running while the driver is in
the middle of its reset path.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLTX is deprecated, don't use it. This completes the removal of LLTX from
the Intel Network drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348eef
"[NET]: Make NAPI polling independent of struct net_device objects."
made NAPI polling to be independent of net_device.
So e1000_adapter->polling_netdev is no longer used.
Kill it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced pci_ioremap_bar() function in drivers/net.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes e1000 to set vlan_features so TSO and CSUM
offload can be used by VLAN devices, similar as with the other
Intel drivers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading transmit checksums only, the driver was not
correctly configuring the hardware to handle the case of a zero
checksum. For UDP the correct behavior is to leave it alone, but
for tcp the checksum must be changed from 0x0000 to 0xFFFF. The
hardware takes care of this case but only if it is told the
packet is tcp.
same patch as e1000e
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the e1000/e1000e split, no hardware supported by e1000
supports packet split, just remove the Kconfig option and associated
code from the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Andrey reports e1000 corruption, and that a patch in vmware's ESX fixed
it.
The EEPROM corruption is triggered by concurrent access of the EEPROM
read/write. Putting a lock around it solve the problem.
[akpm@linux-foundation.org: use DEFINE_SPINLOCK to avoid confusing lockdep]
Signed-off-by: Christopher Li <chrisl@vmware.com>
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Zach Amsden <zach@vmware.com>
Cc: Pratap Subrahmanyam <pratap@vmware.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Here's the patch. It shrinks the stack from 1152 bytes to 192 bytes (the
first version, that only did the e1000_option part, got it down to 600
bytes). About half comes from not using multiple "e1000_option"
structures, the other half comes from turning the "e1000_opt_list[]"
arrays into "static const" instead, so that gcc doesn't copy them onto the
stack.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reveiewed-by: Auke Kok <auke-jan.h.kok@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes e1000 driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed. This is based on the
ioport-free patch of e1000 driver from Auke Kok and Tomohiro Kusumi.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher<jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The email linux-nics@intel.com is no longer available, remove all
references.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Redefine DPRINTK macro using do while(0)
__FUNCTION__ to __func__
structs {} on separate lines
Surround negative constants with ()
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use struct e1000_hw *hw = adapter->hw; where necessary
Change macros E1000_READ_REG and E1000_WRITE_REG to er32 and ew32
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With the recent changes to tx mutiqueue, e1000 was not calling
netif_start_queue() before calling netif_wake_queue().
This causes an oops during loading of the driver.
(Based on commit d55b53fff0
("igb/ixgbe/e1000e: resolve tx multiqueue bug").)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field
for priority mappings, don't truncate the upper 4 bits.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to e1000_clean_tx_irq in e1000_netpoll can race with the call
to e1000_clean_tx_irq in e1000_clean. With a small bit of tweaking to
to netpoll_send_skb to simulate a system that was under extreme stress,
I was able to reproduce these concurrent calls. This can result in
multiple frees to the skbs on the tx ring buffer.
Dropping this call from e1000_netpoll should be fine since we can rely
on the calls in e1000_clean to do what is needed since napi will poll
the hardware just after calling poll_controller.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We do not want to prolong the situation much longer that e1000
and e1000e support these devices at the same time. As a result,
take out the bandage that was added for the interim period
and remove all the PCI Express device IDs from e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When enabling TSO via ethool on e1000, it is possible to set
NETIF_F_TSO6 on hardware that does not support it. Setting TSO via
ethtool now matches the settings used when the hardware is probed.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Conglomerate from 4 separate patches from Joe.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
irq_sem was just a hack to prevent interrupts from being enabled
unexpectedly in deep call paths. Simply finding those call paths and
fixing them by hand results in a driver that behaves as we expect and
doesn't need the atomic at all.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Thu, 2008-03-06 at 10:07 -0800, Kok, Auke wrote:
> send me a patch for e1000 and for ixgb and I'll happily apply those :)
boolean_t to bool
TRUE to true
FALSE to false
comment typo ahread to ahead
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We're already starting to see reports from users still
using e1000 where they should be using e1000e now that this is
actually possible. Just to prevent some of this thrash, add
a big warning on load on these devices that people should
switch to e1000e.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The e1000 driver stores the content of the PCI resources into
unsigned long's before ioremapping. This breaks on 32 bits
platforms that support 64 bits MMIO resources such as ppc 44x.
This fixes it by removing those temporary variables and passing
directly the result of pci_resource_start/len to ioremap.
The side effect is that I removed the assignments to the netdev
fields mem_start, mem_end and base_addr, which are totally useless
for PCI devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
drivers/net/e1000/e1000_main.c | 18 +++++-------------
1 file changed, 5 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global e1000_dump_eeprom() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the old e1000 driver and the new e1000e driver can drive some
PCI-Express e1000 cards, and we should avoid ambiguity about which
driver will pick up the support for those cards when both drivers are
enabled.
This solves the problem by having the old driver support those cards if
the new driver isn't configured, but otherwise ceding support for PCI
Express versions of the e1000 chipset to the newer driver. Thus
allowing both legacy configurations where only the old driver is active
(and handles all chips it knows about) and the new configuration with
the new driver handling the more modern PCIE variants.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new e1000e driver is apparently not yet suitable for general use, so
mark it experimental, and re-instate all the PCI-Express device IDs in
the old and stable e1000 driver so that people (namely me) can continue
to use a driver that actually works.
Auke & co have been appraised of the situation.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To help supporting users with a bad eeprom checksum, dump the
eeprom info when such a situation is encountered by a user.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for configuring secondary unicast addresses. Unicast
addresses take precendece over multicast addresses when filling
the exact address filters to avoid going to promiscous mode.
When more unicast addresses are present than filter slots,
unicast filtering is disabled and all slots can be used for
multicast addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal macro to function conversion in e1000_ethtool.c
Adds functions reg_pattern_test and reg_set_and_check
Changes REG_PATTERN_TEST and REG_SET_AND_CHECK macros
to call these functions.
Saves ~2.5KB
Compiled x86, untested (no hardware)
old:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
16778 0 0 16778 418a drivers/net/e1000/e1000_ethtool.o
new:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
14128 0 0 14128 3730 drivers/net/e1000/e1000_ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.
The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.
This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().
Unfortunately, this trips up the semaphore used here in the Intel
drivers. If you hit this case, when you try to bring the interface
back up it won't enable interrupts. A reload of the driver module
fixes it of course.
So what we do is make sure all the sequences now go:
napi_disable();
atomic_set(&adapter->irq_sem, 0);
*_irq_disable();
which makes sure the counter is always in the correct state.
Reported by Robert Olsson.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression added by changeset
53e52c729c ("[NET]: Make ->poll()
breakout consistent in Intel ethernet drivers.")
As pointed out by Jesse Brandeburg, for three of the drivers edited
above there is breakout logic in the *_clean_tx_irq() code to prevent
running TX reclaim forever. If this occurs, we have to elide NAPI
poll completion or else those TX events will never be serviced.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.
Now they will all break out when the amount of RX work done is less
than 'budget'.
At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this). But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.
Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't exit polling when we have not yet used our budget, this causes
the NAPI system to end up with a messed up poll list.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
mii-tool can cause the driver to call msleep during nway reset,
bugzilla.kernel.org bug 8430. Fix by simply calling reinit_locked
outside of the spinlock, which is safe from ethtool, so it should be
safe from here.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings and problems from e1000 driver.
Added a sparse fix for the module param array index
-- Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These driver changes incorporate the proposed PCI-X / PCI-Express read byte
count interface. Reading and setting those valuse doesn't take place
"manually", instead wrapping functions are called to allow quirks for some
PCI bridges.
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This blade-specific board form factor is identical to the 82571EB
board.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
