fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o New CKSUM flag added by fw to notify cksum is verified.
o Update version to 5.0.9
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hypervisor allows, two VM's interfaces to have same mac address.
These VM's interfaces get differentiate with Vlan tag.
This patch add support to learn and configure mac+vlan filter on device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device eswitch need to configure with VM's mac address.
Hypervisor doesn't provide any utility/callbacks to get VM's mac address.
Unicast mac address filter improves performance and also provide
packet loopback capability i.e communication between VM.
Above features is by default off, can be turned on with module parameter
'mac_learn'.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Rename mac_learning to mac_override
o Added check in set_mac to return error if mac override is disabled.
o Disabling mac_override only supported for Non priviledged functions.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o skb->mac_header is not set, so machine panics while using function eth_hdr.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow enabling/disabling mac anti spoof policy only for
Non privilege functions.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Default eswitch config was set, even before eswitch capabilty get detected.
As a result setting default config was getting fail.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Mac addr was read from flash for every fw reset
for Non-priviledge function.It should be read only once.
o Remove unnecessary get_mac_addr callback
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o ethtool reg version bumped to 2
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Backing out "firmware initialization update" changes, commit-id
"d4066833bb1b35fefb1dd45eb2b10659d46bf151".
o fix heartbit spelling, it should be heartbeat
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added PCI ID to board info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a FW hang when the driver loads, it can not determine the FW operational
mode. Fix it by checking the FW state first before issuing any FW commands to
determine its capabilities and thereby detecting driver operational mode.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, the error codes returned from some of the functions
are not caught and sent up the caller chain. Fixed it here.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change QLCNIC_CRB_DEV_REF_COUNT to QLCNIC_CRB_DRV_ACTIVE to match
document.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Privilege function should wait for npar state to be operational
before creating context.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On NIC Partition capable adapter, Administrator can configure to
tag packet with particular vlan id. Packet will be tagged and strip with
that vlan id. Also if 'Tagging' flag is disable, other packet will be drop.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove validation before deleting vlan id
o Add missing 'break' while deleting vlan id.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_intr has pointer to qlcnic_host_sds_ring
as second parameter not pointer to qlcnic_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fw can get stuck while holding pci semaphore. Driver will not
be able to perform fw initialization, without this lock.
Release semaphore forcefully in that case.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup legacy code which is not valid for Qlogic
CNA adapters.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark device state failed in error path.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Privilege functions should wait for npar state to be operational.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Administrator can configure to drop packet in transmit,
if it doesn't match interface mac address, in case of virtual function.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device is not capable of enabling/disabling offload setting per
port in case of Nic Partition.So offload settings needs to be
enabled/disabled per eswitch and it will affect all the function
on that eswitch.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Nic partition capable devices has embedded switch, this needs to support
various features like external switch.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Serial number references are not used in driver.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spin_lock(rds_ring->lock) is not required while posting buffers
from qlcnic_open and freeing buffers from qlcnic_down.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error code is stored in the variable err, but it is the variable ret
that is returned instead. So store the error code in ret. Err is then
useless.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Also dont allow lro to be turn on, if rx csum is disabled
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Give sufficient time for all makes of PHY modules
to establish the link after loopback test.
o Perform online test before offline test.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display interface name with netdev_info() for link status message.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding eswitch statistics support. User can get
whole eswitch stats or stats of func belong to that eswitch.
Added:
o command to get statistics of eswitch and function.
o sysfs support to export eswitch and func statatistics.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
function modes was not working with CNA device, in CNA mode
other function(FCOE) can be enabled before nic.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o NPAR state should be set to operationl by Mangement function only.
o NPAR state should be set to non operational before device reset.
o VF function should wait for NPAR state to be operational.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual function are not privilge to initialize firmware.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes.
That's a lot if you run with 4K stacks. I allocated them with kcalloc()
instead.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code we allocated memory conditionally and freed it in
the error handling unconditionally. It turns out that this function is
only called during initialization and "adapter->npars" and
"adapter->eswitch" are always NULL at the start of the function. I
removed those checks.
Also since I was cleaning things, I changed the error handling for
qlcnic_get_pci_info() and pulled everything in an indent level.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_attach missing from error path in qlcnic_diag_alloc_res
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback not supported for virtual function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix maximum and minmum bandwith value.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_get_domain_bus_and_slot: caller must decrement the
reference count by calling pci_dev_put().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o NPAR configuration which is programmed in fw, need to
restore after fw recovery.
o Update version to 5.0.7
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci error recovery support added.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>