The patch below fixes the following sparse warning:
drivers/mtd/maps/nettel.c:482:27: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arjan: drivers/mtd/maps/sc520cdp.c:167: warning: par_table is never written to and should be declared 'const'
arjan: drivers/mtd/maps/pci.c:105: warning: mtd_pci_map is never written to and should be declared 'const'
arjan: mind fixing those up ?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ixp4xx updates:
- Handle reads that don't start on a half-word boundary.
- Make it work when CPU is in little-endian mode.
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Recent models of Intel/Sharp and Spansion CFI flash now have significant
bits in the upper byte of device ID codes, read via what Spansion calls
"autoselect" and Intel calls "read device identifier". Currently these
values are truncated to the low 8 bits in the mtd data structures, as
all CFI read query info has previously been read one byte at a time.
Add a new method for reading 16-bit info, currently just manufacturer
and device codes; datasheets hint at future uses for upper bytes in
other fields.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge from linux-mips:
Use physical addresses at the interface level, letting drivers remap
them as appropriate.
Signed-off-by: Maciej W. Rozycki <macro@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If you have an array with a write-intent-bitmap, and you remove a device, then
re-add it, a full recovery isn't needed. We detect a re-add by looking at
saved_raid_disk. For raid1, it doesn't matter which disk it was, only whether
or not it was an active device. The old code being removed set a value of
'mirror' which was then ignored, so it can go. The changed code performs the
correct check.
For raid6, if there are two missing devices, make sure we chose the right slot
on --re-add rather than always the first slot.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If an array is created using set_array_info, default_bitmap_offset isn't set
properly meaning that an internal bitmap cannot be hot-added until the array
is stopped and re-assembled.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When doing a recovery, we need to know whether the array will still be
degraded after the recovery has finished, so we can know whether bits can be
clearred yet or not. This patch performs the required check.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bitmap_unplug actually writes data (bits) to storage, so we shouldn't be
holding a spinlock...
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
raid10 has two different layouts. One uses near-copies (so multiple
copies of a block are at the same or similar offsets of different
devices) and the other uses far-copies (so multiple copies of a block
are stored a greatly different offsets on different devices). The point
of far-copies is that it allows the first section (normally first half)
to be layed out in normal raid0 style, and thus provide raid0 sequential
read performance.
Unfortunately, the read balancing in raid10 makes some poor decisions
for far-copies arrays and you don't get the desired performance. So
turn off that bad bit of read_balance for far-copies arrays.
With this patch, read speed of an 'f2' array is comparable with a raid0
with the same number of devices, though write speed is ofcourse still
very slow.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is for supporting IDE interface for M3A-2170(Mappi-III) board.
Signed-off-by: Mamoru Sakugawa <sakugawa@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove bogus usage of test/set_bit() from fbcon rotation code and just
manipulate the bits directly. This fixes an oops on powerpc among others
and should be faster. Seems to work fine on the G5 here.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some callers in cpufreq hotplug notify path that the lowest
function calls lock_cpu_hotplug(). The lock is already held during
cpu_up() and cpu_down() calls when the notify calls are broadcast to
registered clients.
Ideally if possible, we could disable_preempt() at the highest caller and
make sure we dont sleep in the path down in cpufreq->driver_target() calls
but the calls are so intertwined and cumbersome to cleanup.
Hence we consistently use lock_cpu_hotplug() and unlock_cpu_hotplug() in
all places.
- Removed export of cpucontrol semaphore and made it static.
- removed explicit uses of up/down with lock_cpu_hotplug()
so we can keep track of the the callers in same thread context and
just keep refcounts without calling a down() that causes a deadlock.
- Removed current_in_hotplug() uses
- Removed PF_HOTPLUG_CPU in sched.h introduced for the current_in_hotplug()
temporary workaround.
Tested with insmod of cpufreq_stat.ko, and logical online/offline
to make sure we dont have any hang situations.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Cc: Zwane Mwaikambo <zwane@linuxpower.ca>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This replaces the (in my opinion horrible) VM_UNMAPPED logic with very
explicit support for a "remapped page range" aka VM_PFNMAP. It allows a
VM area to contain an arbitrary range of page table entries that the VM
never touches, and never considers to be normal pages.
Any user of "remap_pfn_range()" automatically gets this new
functionality, and doesn't even have to mark the pages reserved or
indeed mark them any other way. It just works. As a side effect, doing
mmap() on /dev/mem works for arbitrary ranges.
Sparc update from David in the next commit.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch marks a few serial data structures const, moving them to
.rodata where they won't false-share cachelines with things that get
written to.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A review against MMC/SD specifications found some errors in the current
implementation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Coverity checker spotted this obvious use-after-release bug caused
by a wrong order of the cleanups.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This code fixes a tiny problem with the recent fbcon rotation changes:
fb_prepare_logo doesn't check the return value of fb_find_logo and that
causes a crash for my while booting.
Obvious & working & tested fix is here.
Signed-off-by: Jasper Spaans <jasper@vs19.net>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A fix for a locking bug which is triggered when a client tries to lock with
flag DMA_QUIESCENT (typically the X server), but gets interrupted by a signal.
The locking IOCTL should then return an error, but if DMA_QUIESCENT succeeds
it returns 0, and the client falsely thinks it has the lock. In addition
The client waits for DMA_QUISCENT and possibly DMA_READY without having the lock.
From: Thomas Hellstrom
Signed-off-by: Dave Airlie <airlied@linux.ie>
remove redundant include
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Wed, Nov 16, 2005 at 06:34:24PM -0800, Pete Zaitcev wrote:
>On Wed, 16 Nov 2005 23:52:32 +0100, David Hrdeman <david@2gen.com> wrote:
>> usb-storage: waiting for device to settle before scanning
>> Vendor: I0MEGA Model: UMni1GB*IOM2K4 Rev: 1.01
>> Type: Direct-Access ANSI SCSI revision: 02
>> SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
>> sda: Write Protect is off
>> sda: Mode Sense: 00 00 00 00
>> sda: assuming drive cache: write through
>> ioctl_internal_command: <8 0 0 0> return code = 8000002
>> : Current: sense key=0x0
>> ASC=0x0 ASCQ=0x0
>> SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
>
>I think it's harmless. I saw things like that, and initially I plugged
>them with workarounds like this:
Thanks for the pointer, and yes, it is harmless, but it floods the
console with the messages which hides other (potentially important)
messages...following your example I've made a patch which fixes the
problem.
Signed-off-by: David Hrdeman <david@2gen.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This should fix a suspend/resume issues that appear with OHCI on some
PPC hardware. The PCI layer should doesn't have the hooks needed for
such ASIC-specific hooks (in this case, software clock gating), so
this moves the code to do that into hcd-pci.c ... where it can be
done after the relevant PCI PM state transition (to/from D3).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Moving the PCI-specific parts of the EHCI driver into their own file
created a few issues ... notably on resume paths which (like swsusp)
require re-initializing the controller. This patch:
- Splits the EHCI startup code into run-once HCD setup code and
separate "init the hardware" reinit code. (That reinit code is
a superset of the "early usb handoff" code.)
- Then it makes the PCI init code run both, and the resume code only
run the reinit code.
- It also removes needless pci wrappers around EHCI start/stop methods.
- Removes a byteswap issue that would be seen on big-endian hardware.
The HCD glue still doesn't actually provide a good way to do all this
run-one init stuff in one place though.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This cleans up the recent updates to EHCI PCI support:
- Gets rid of checks for "is this a PCI device", they're no
longer needed since this is now all PCI-only code.
- Reduce log spamming: MWI is only interesting in the atypical
case that it can actually be used.
- Whitespace cleanup, as appropriate for a new file with no
other pending patches.
So other than that minor logging change, no functional updates.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes some bugs in EHCI suspend/resume that joined us over the past
few releases (as usbcore, PCI, pmcore, and other components evolved):
- Removes suspend and resume recursion from the EHCI driver, getting
rid of the USB_SUSPEND special casing.
- Updates the wakeup mechanism to work again; there's a newish usbcore
call it needs to use.
- Provide simpler tests for "do we need to restart from scratch", to
address another case where PCI Vaux was lost. (In this case it was
restoring a swsusp snapshot, but there could be others.)
Un-exports a symbol that was temporarily exported.
A notable change from previous version is that this doesn't move
the spinlock init, so there's still a resume/reinit path bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Stefan Nies of KOBIL Systems for
two of their devices using the FTDI chip.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch solves the following problem I've already discovered on the
latest 2.6.15-rc1-git1 kernel:
Nov 13 07:37:28 wrobel kernel: Bad page state at free_hot_cold_page (in process 'motion', page c164e020)
Nov 13 07:37:28 wrobel kernel: flags:0x40000400 mapping:00000000 mapcount:0 count:0
Nov 13 07:37:28 wrobel kernel: Backtrace:
Nov 13 07:37:28 wrobel kernel: [<c0146d86>] bad_page+0x85/0xbe
Nov 13 07:37:28 wrobel kernel: [<c0147629>] free_hot_cold_page+0x54/0x129
Nov 13 07:37:28 wrobel kernel: [<c01598c6>] __vunmap+0xa9/0xfe
Nov 13 07:37:28 wrobel kernel: [<c0154114>] vmalloc_to_page+0x34/0x55
Nov 13 07:37:28 wrobel kernel: [<c0159942>] vfree+0x27/0x35
Nov 13 07:37:28 wrobel kernel: [<f8a20292>] sn9c102_release_buffers+0x30/0x3f [sn9c102]
Nov 13 07:37:28 wrobel kernel: [<f8a231c2>] sn9c102_release+0x37/0xeb [sn9c102]
Nov 13 07:37:28 wrobel kernel: [<c0163e74>] __fput+0xa9/0x1aa
Nov 13 07:37:28 wrobel kernel: [<c01624f7>] filp_close+0x49/0x6d
Nov 13 07:37:30 wrobel kernel: [<c016258f>] sys_close+0x74/0x95
Nov 13 07:37:30 wrobel kernel: [<c0102ef9>] syscall_call+0x7/0xb
Nov 13 07:37:31 wrobel kernel: Trying to fix it up, but a reboot is needed
Signed-off-by: Damian Wrobel <dwrobel@ertel.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per the PCI Express spec, the power-fault-detected bit in the
slot status register can be set anytime hardware detects a power
fault, regardless of whether the slot has a device populated in
it or not. This bit is sticky and must be explicitly cleared.
This patch is needed to allow hot-add after such a power fault
has been detected.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial patch to report both hdaps axises to the joystick device, not
just the X axis.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug where setting the low fan speed limits will not work if no
data was ever read through the sysfs interface and the fan clock
dividers have not been explicitely set yet either. The reason is that
data->fan_div[nr] may currently be used before it is initialized from
the chip register values. The fix is to explicitely initialize
data->fan_div[nr] before using it.
Bug reported, and fix tested, by Nicolas Mailhot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the lm78 VID reading, which I accidentally broke while making
this driver use the common vid_from_reg function rather than
reimplementing its own in 2.6.14-rc1.
I'm not proud of it, trust me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add SENSORS_LIMIT in store VCore limit functions. This fixes a potential
u8 overflow on out-of-range user input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (as603) makes a few small fixes to the driver core:
Change spin_lock_irq for a klist lock to spin_lock;
Fix reference count leaks;
Minor spelling and formatting changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fix causes problems on the very first floppy access - we haven't yet
talked to the FDC so we don't know which state the write-protect tab is in.
Revert for now.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We memset the structure across opens except for the flags. The correct
fix is more intrusive but this should fix a problem with bad iounmaps
seen on AGP radeons acting like PCI ones.
Signed-off-by: Dave Airlie <airlied@linux.ie>
The DRM only uses drm_alloc_pages for non-SG PCI cards using DRM.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
PCI->PCI bridge, then bus->self is allowed to be NULL. Certainly that's
the case on my Pegasos, and it makes the MGA DRM driver oops...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The spinlock region_lock is held while calling mark_region which can sleep.
Drop the spinlock before calling that function.
A region's state and inclusion in the clean list are altered by rh_inc and
rh_dec. The state variable is set to RH_CLEAN in rh_dec, but only if
'pending' is zero. It is set to RH_DIRTY in rh_inc, but not if it is already
so. The changes to 'pending', the state, and the region's inclusion in the
clean list need to be atomicly.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bio_list_merge() should do nothing if the second list is empty - not oops.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
