mxs is a device tree only platform, which allows us to simplify a bit
mxs_sgtl5000_probe(), because there is no need to check whether device tree is
supported or not.
Remove mxs_sgtl5000_probe_dt() and place its content inside mxs_sgtl5000_probe()
for making the code simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On a mx28 board, running "aplay -l" and "arecord -l" results in the following:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
,which is not correct because we got a capture device listed in aplay and a
playback device listed in arecord.
On mx28 there are two serial audio interface ports (SAIF0 and SAIF1) and each
one of them are unidirectional.
Allow to specify a dai link as 'playback_only' or 'capture_only', which suits
well for this case.
After this change we can correctly report the capabilities as follows:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: HiFi Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: HiFi Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
Also tested playback and capture on the mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It makes no sense to hardcode the I2C bus into the codec_name field.
cpu_dai_name and platform_name are also overwritten later in
mxs_sgtl5000_probe_dt().
So remove the three fields, as mxs platform is dt-only platform.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Variable 'ret' is not needed here, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prior to this patch, the CPU side of a DAI link was specified using a
single name. Often, this was the result of calling dev_name() on the
device providing the DAI, but in the case of a CPU DAI driver that
provided multiple DAIs, it needed to mix together both the device name
and some device-relative name, in order to form a single globally unique
name.
However, the CODEC side of the DAI link was specified using separate
fields for device (name or OF node) and device-relative DAI name.
This patch allows the CPU side of a DAI link to be specified in the same
way as the CODEC side, separating concepts of device and device-relative
DAI name.
I believe this will be important in multi-codec and/or dynamic PCM
scenarios, where a single CPU driver provides multiple DAIs, while also
booting using device tree, with accompanying desire not to hard-code the
CPU side device's name into the original .cpu_dai_name field.
Ideally, both the CPU DAI and CODEC DAI loops in soc_bind_dai_link()
would now be identical. However, two things prevent that at present:
1) The need to save rtd->codec for the CODEC side, which means we have
to search for the CODEC explicitly, and not just the CODEC side DAI.
2) Since we know the CODEC side DAI is part of a codec, and not just
a standalone DAI, it's slightly more efficient to convert .codec_name/
.codec_of_node into a codec first, and then compare each DAI's .codec
field, since this avoids strcmp() on each DAI's CODEC's name within
the loop.
However, the two loops are essentially semantically equivalent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for mxs-sgtl5000 machine driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Same as the commit 518de86 (ASoC: tegra: register 'platform' from DAIs,
get rid of pdev), it makes mxs-pcm not a platform_driver but helper to
register "platform", so that the platform_device for mxs-pcm can be
saved completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add missing .owner of struct snd_soc_card. This prevents the module from being
removed from underneath its users.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver only supports playback firstly.
For recording, as we have to use two saif instances to implement full
duplex (playback & recording) due to hardware limitation, we need to
figure out a good design to fit in ASoC.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
