The upstream tree has the ATA_DFLAG_PIO bug fixed but does not have the
pass throuugh bug fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure the pio_mode is always setup. Don't do any setup on the controller b
just ensure the mode reporting is valid to avoid tons of special cases
in PATA driver code when mode switching on the fly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Backport the "pio flush" from the libata major update to 2.6.17 for via atapi.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Relax the lowmem bounce buffer requirement for imm so that any
low memory page will do -- they don't need to be below the
ISA 16 MB limit, just need to be mapped in low memory.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Semantic changes in ISP24xx firmware behaviour inadvertently
caused the driver to believe an F-port topology was present in an
N_port-to-N_port configuration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify and centralise buffer allocation/deallocation, as
there's no point in having two memory request methods.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Expandind on the previous commit:
commit 79f89a4296
Author: andrew.vasquez@qlogic.com <andrew.vasquez@qlogic.com>
Date: Fri Jan 13 17:05:58 2006 -0800
[SCSI] qla2xxx: Disable port-type RSCN handling via driver state-machine.
and given:
- the process-context requirements of the FC transport
rport-APIs.
- lack of port-type RSCN processing logic for ISP24xx and newer
chips.
it's time now to remove the state-machine logic from mainline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In qla2x00_reset_chip the driver first takes the hardware lock,
and then later on takes the mbx lock.
In the mailbox_command code.. it goes the other way around.
Discovered with the lock validator.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If firmware image is unavailable via request_firwmare(), then
attempt to load the image (likely out-of-date) stored in flash
memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With ISP24XX and ISP54XX parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do not flush queues then block session. This will cause commands
to needlessly swing around on us and remove goofy
recovery_failed field and replace with state value.
And do not start recovery from within the host reset function.
This causeis too many problems becuase open-iscsi was desinged to
call out to userspace then have userpscae decide if we should
go into recovery or kill the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from david.somayajulu@qlogic.com and cleaned up by Tomo.
qla4xxx is going to have a different daemon so this patch
just routes the events to the right daemon.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Discovered by steven@hayter.me.uk and patch by michaelc@cs.wisc.edu
The dtask mempool is reserving 261120 items per session! Since we are now
sending headers with sendmsg there is no reason for the mempool and that
was causing us to us carzy amounts of mem. We can preallicate a header in
the r2t and task struct and reuse them
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We only use the mtask data buffer for login tasks so we do not
need to preallocate a buffer for every mtask. This saves
8 * 31 KB.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Zhen and ported by Mike:
Don't use sendpage for the headers. sendpage for the pdu headers
does not seem to have a performance impact, makes life harder
for mutiple data pdus to be in flight and still trips up some
network cards when it is from slab mem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
The queue tracking is just not being used, not even for debugging. Information
about outstanding commands can be acquired from the scsi structures.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
A race condition existed that could result in a lost completion of a
command to the ppc based cards.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Add the ability to adjust for unusual corner case failures. Both of
these additional module parameters deal with embedded, non-intel or
complicated system scenarios.
Aif_timeout can be increased past the default 2 minute timeout to drop
application registrations when a system has an unusually high event load
resulting from continuing management requests, or simultaneous builds,
or sluggish user space as a result of system load.
Startup_timeout can be increased past the default 3 minute timeout to
drop an adapter initialization for systems that have a very large number
of targets, or slow to spin-up targets, or a complicated set of array
configurations that extend the time for the firmware to declare that it
is operational. This timeout would only have an affect on non-intel
based systems, as the (more patient) BIOS would generally be where the
startup delay would be dealt with.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Slight space and speed efficiency improvement.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Since new commands to the card are quiesced, respect the changes in
the SCSI error path which dropped locking around the hba reset handler
and similarly drop the lock requirement in the driver's path.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A couple write attributes in sas transport layer have a small
bug that prevents them from being written to. Those
attributes are the link_reset and write_reset. This is due
the store field being set to NULL.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
the user_scan() callback currently has the potential to identify the
wrong device in the presence of expanders. This is because it finds
the first device with a matching target_id, which might be an
expander. Fix this by making it look specifically for end devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libata implemented a feature to schedule EH without an associated EH
by manipulating shost->host_eh_scheduled in ata_scsi_schedule_eh()
directly. Move this function to scsi_error.c and rename it to
scsi_schedule_eh(). It is now an exported API for SCSI transports and
exported via new header file drivers/scsi/scsi_transport_api.h
This patch also de-export scsi_eh_wakeup() which was exported
specifically for ata_scsi_schedule_eh().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LLDDs rely on libata that certain EH actions are automatically taken
on some errors. If the port is frozen or one or more qc's have failed
with HSM violation or timeout, softreset is enforced (LLDD can ask for
storonger EH action at will). If any other error condition exists,
libata EH always revalidates.
This behavior existed in earlier revisions of new EH but lost during
development process. This patch restores it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the HSM error_mask mapping.
Changes:
- Better mapping in ac_err_mask()
- In HSM_ST_FIRST ans HSM_ST state, check ATA_ERR|ATA_DF and map it to AC_ERR_DEV instead of AC_ERR_HSM.
- In HSM_ST_FIRST and HSM_ST state, map DRQ=1 ERR=1 to AC_ERR_HSM.
- For PIO data in and DRQ=1 ERR=1, add check after the junk data block is read.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform. His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them. Look for another patch for those (soon).
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.
This patch removes the local copies, in favour of just accessing the hardware
whenever we need them. Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis. The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.
This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still has ATA_BUSY asserted.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it. These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register. Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).
While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it. This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function. This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.
This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels. This should not be needed,
in theory, but in practice it has caught bugs. Maybe nuke it at a later date.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ppa cannot handle highmem pages, and like imm, which already has
this patch, the device is slow, so performance is not a big issue,
so just force pages to be in low memory (hence mapped).
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
after upgrading our SUN E250 from 2.4 to 2.6 I'm seeing following error
when the HP DDS4 DAT changer gets probed:
scsi: host 1 channel 0 id 5 lun16777216 has a LUN larger than allowed by
the host adapter
The device is connected to a symbios 875 host. I've talked to Willy
about the problem, and he asked me to try to blacklist the device
for reportlun. I did that with the patch below and it solved the
problem. It now gets properly detected:
target1:0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
Vendor: HP Model: C5713A Rev: H307
Type: Sequential-Access ANSI SCSI revision: 03
target1:0:5: Beginning Domain Validation
target1:0:5: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 16)
target1:0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16)
target1:0:5: Domain Validation skipping write tests
target1:0:5: Ending Domain Validation
Vendor: HP Model: C5713A Rev: H307
Type: Medium Changer ANSI SCSI revision: 03
Signed-off-by: tsbogend@alpha.franken.de
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implement NCQ support. Sil24 has 31 command slots and all of them are
used for NCQ command queueing. libata guarantees that no other
command is in progress when it issues an internal command, so always
use tag 0 for internal commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With NCQ, there are multiple sg tables, so pp->cmd_tbl_sg doesn't cut
it. Directly calculate sg table address from pp->cmd_tbl.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* Rename CMD_TBL_HDR to CMD_TBL_HDR_SZ as it's size not offset.
* Define MAX_CMDS and CMD_SZ and use them in calculation of other
constants.
* Define CMD_TBL_AR_SZ as product of CMD_TBL_SZ and MAX_CMDS, and use
it when calculating PRIV_DMA_SZ.
* CMD_SLOT_SZ is also dependent on MAX_CMDS but hasn't been changed
because I didn't want to change the value used by the original code
(32 commands). Later NCQ change will bump MAX_CMDS to 32 anyway and
the hard coded 32 can be changed to MAX_CMDS then.
* Reorder HOST_CAP_* flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all NCQ related stuff are in place, implement NCQ device
configuration and bump ATA_MAX_QUEUE to 32 thus activating NCQ
support.
Original implementation is from Jens Axboe.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update EH to handle NCQ. ata_eh_autopsy() is updated to call
ata_eh_analyze_ncq_error() which reads log page 10h on NCQ device
error and updates eh_context accordingly. ata_eh_report() is updated
to report SActive.
Signed-off-by: Tejun Heo <htejun@gmail.com>
This patch implements NCQ command translation and exclusion. Note
that NCQ commands don't use ata_rwcmd_protocol() to choose ATA
command. This is because, unlike non-NCQ RW commands, NCQ commands
can only be used for NCQ protocol and FUA handling is done with a flag
rather than separate command.
NCQ enabled device will have queue depth larger than one but no two
non-NCQ commands can be issued simultaneously, neither can a non-NCQ
command and NCQ commands. This patch makes ata_scsi_translate()
return SCSI_MLQUEUE_DEVICE_BUSY if such exclusion is necessary. SCSI
midlayer will retry the command later.
As SCSI midlayer always retries once a command completes, this doesn't
incur unnecessary delays and as most commands will be NCQ ones for NCQ
device, so the overhead should be negligible.
Initial implementation is from Jens Axboe and using
SCSI_MLQUEUE_DEVICE_BUSY for exclusion is suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add ap->qc_active and ap->sactive, mask of all active qcs and libata's
view of the SActive register, respectively. Also, implement
ata_qc_complete_multiple() which takes new qc_active mask and complete
multiple qcs according to the mask.
These will be used to track NCQ commands and complete them. The
distinction between ap->qc_active and ap->sactive is also useful for
later PM implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rename ap->qactive to ap->qc_allocated. This is to accomodate
addition of ap->qc_active, mask of active qcs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_scsi_translate() will need to return SCSI_ML_QUEUE_DEVICE_BUSY to
achieve exlusion between NCQ and non-NCQ commands or among non-NCQ
commands. Pass its return value upward to SCSI midlayer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* kill ata_poll_qc_complete() and implement/use ata_hsm_qc_complete()
which completes qcs in new EH compliant manner from HSM
* don't print error message from ata_hsm_move(). it's responsibility
of EH.
* kill ATA_FLAG_NOINTR usage in bmdma EH
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert sata_sil24 to new EH.
* When port is frozen, IRQ for the port is masked.
* sil24_softreset() doesn't need to mangle with IRQ mask anymore.
libata ensures that the port is frozen during reset.
* Only turn on interrupts which are handled by interrupt handler and
EH. As we don't handle SDB notify yet, turn it off. DEV_XCHG and
UNK_FIS are handled by EH and thus turned on.
* sil24_softreset() usually fails to recover the port after DEV_XCHG.
ATA_PORT_HARDRESET is used as recovery action for DEV_XCHG.
* sil24 may be invoked without any active command. e.g. DEV_XCHG irq
occuring while no qc in progress still triggers EH and will reset
the port and revalidate attached device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
During multiblock PIO, multiple PIOS interrupts are generated before
qc compltion. Current code prints unnecessary message for such cases.
This is exposed when new EH slows down attached device into PIO mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert AHCI to new EH. Unfortunately, ICH7 AHCI reacts badly if IRQ
mask is diddled during operation. So, freezing is implemented by
unconditionally clearing interrupt conditions while frozen.
* Interrupts are categorized according to required action.
e.g. Connection status or unknown FIS error requires freezing the
port while TF or HBUS_DATA don't.
* Only CONNECT (reflects SErr.X) interrupt is taken into account not
PHYRDY (SErr.N), as CONNECT is better cue for starting EH.
* AHCI may be invoked without any active command. e.g. CONNECT irq
occuring while no qc in progress still triggers EH and will reset
the port and revalidate attached device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Convert sata_sil to new EH. As these controllers have hardware
interrupt mask and are known to have screaming interrupts issues, use
hardware IRQ masking for freezing. sil_freeze() masks interrupts for
the port and sil_thaw() unmasks them. As ports are automatically
frozen before probing reset, there is no need to initialize interrupt
masks sil_init_onde(). Remove related code.
Other than freezing, sata_sil uses stock BMDMA EH routines.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement new EH. The exported interface is ata_do_eh() which is to
be called from ->error_handler and performs the following steps to
recover the failed port.
ata_eh_autopsy() : analyze SError/TF, determine the cause of failure
and required recovery actions and record it in
ap->eh_context
ata_eh_report() : report the failure to user
ata_eh_recover() : perform recovery actions described in ap->eh_context
ata_eh_finish() : finish failed qcs
LLDDs can customize error handling by modifying eh_context before
calling ata_do_eh() or, if necessary, doing so inbetween each major
steps by calling each step explicitly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
struct ata_eh_info serves as the communication channel between
execution path and EH. Execution path describes detected error
condition in ap->eh_info and EH recovers the port using it. To avoid
missing error conditions detected during EH, EH makes its own copy of
eh_info and clears it on entry allowing error info to accumulate
during EH.
Most EH states including EH's copy of eh_info are stored in
ap->eh_context (struct ata_eh_context) which is owned by EH and thus
doesn't require any synchronization to access and alter. This
standardized context makes it easy to integrate various parts of EH
and extend EH to handle multiple links (for PM).
Signed-off-by: Tejun Heo <htejun@gmail.com>
This patch implements ata_ering and uses it to define dev->ering.
ata_ering is a ring buffer which records libata errors - whether a
command was for normar IO request, err_mask and timestamp. Errors are
recorded per-device in dev->ering. This will be used by EH to
determine recovery actions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SCSI command completion path used to do some part of EH including
printing messages and obtaining sense data. With new EH, all these
are responsibilities of the EH, update SCSI command completion path to
reflect this.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update ata_exec_internal() such that it uses new EH framework.
->post_internal_cmd() is always invoked regardless of completion
status. Also, when ata_exec_internal() detects a timeout condition
and new EH is in place, it freezes the port as timeout for normal
commands would do.
Note that ata_port_flush_task() is called regardless of
wait_for_completion status. This is necessary as exceptions unrelated
to the qc can abort the qc, in which case PIO task could still be
running after the wait for completion returns.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Update ata_scsi_error() for new EH. ata_scsi_error() is responsible
for claiming timed out qcs and invoking ->error_handler in safe and
synchronized manner. As the state of the controller is unknown if a
qc has timed out, the port is frozen in such cases.
Note that ata_scsi_timed_out() isn't used for new EH. This is because
a timed out qc cannot be claimed by EH without freezing the port and
freezing the port in ata_scsi_timed_out() results in unnecessary
abortion of other active qcs. ata_scsi_timed_out() can be removed
once all drivers are converted to new EH.
While at it, add 'TODO: kill' comments to old EH functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
PIO executes without holding host_set lock, so it cannot be
synchronized using the same mechanism as interrupt driven execution.
port_task framework makes sure that EH is not entered until PIO task
is flushed, so PIO task can be sure the qc in progress won't go away
underneath it. One thing it cannot be sure of is whether the qc has
already been scheduled for EH by another exception condition while
host_set lock was released.
This patch makes ata_poll_qc-complete() handle such conditions
properly and make it freeze the port if HSM violation is detected
during PIO execution.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Freezing is performed atomic w.r.t. host_set->lock and once frozen
LLDD is not allowed to access the port or any qc on it. Also, libata
makes sure that no new qc gets issued to a frozen port.
A frozen port is thawed after a reset operation completes
successfully, so reset methods must do its job while the port is
frozen. During initialization all ports get frozen before requesting
IRQ, so reset methods are always invoked on a frozen port.
Optional ->freeze and ->thaw operations notify LLDD that the port is
being frozen and thawed, respectively. LLDD can disable/enable
hardware interrupt in these callbacks if the controller's IRQ mask can
be changed dynamically. If the controller doesn't allow such
operation, LLDD can check for frozen state in the interrupt handler
and ack/clear interrupts unconditionally while frozen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_port_schedule_eh() directly schedules EH for @ap without
associated qc. Once EH scheduled, no further qc is allowed and EH
kicks in as soon as all currently active qc's are drained.
ata_port_abort() schedules all currently active commands for EH by
qc_completing them with ATA_QCFLAG_FAILED set. If ata_port_abort()
doesn't find any qc to abort, it directly schedule EH using
ata_port_schedule_eh().
These two functions provide ways to invoke EH for conditions which
aren't directly related to any specfic qc.
Signed-off-by: Tejun Heo <htejun@gmail.com>
There are several ways a qc can get schedule for EH in new EH. This
patch implements one of them - completing a qc with ATA_QCFLAG_FAILED
set or with non-zero qc->err_mask. ALL such qc's are examined by EH.
New EH schedules a qc for EH from completion iff ->error_handler is
implemented, qc is marked as failed or qc->err_mask is non-zero and
the command is not an internal command (internal cmd is handled via
->post_internal_cmd). The EH scheduling itself is performed by asking
SCSI midlayer to schedule EH for the specified scmd.
For drivers implementing old-EH, nothing changes. As this change
makes ata_qc_complete() rather large, it's not inlined anymore and
__ata_qc_complete() is exported to other parts of libata for later
use.
Signed-off-by: Tejun Heo <htejun@gmail.com>
New EH framework has clear distinction about who owns a qc. Every qc
starts owned by normal execution path - PIO, interrupt or whatever.
When an exception condition occurs which affects the qc, the qc gets
scheduled for EH. Note that some events (say, link lost and regained,
command timeout) may schedule qc's which are not directly related but
could have been affected for EH too. Scheduling for EH is atomic
w.r.t. ap->host_set->lock and once schedule for EH, normal execution
path is not allowed to access the qc in whatever way. (PIO
synchronization acts a bit different and will be dealt with later)
This patch make ata_qc_from_tag() check whether a qc is active and
owned by normal path before returning it. If conditions don't match,
NULL is returned and thus access to the qc is denied.
__ata_qc_from_tag() is the original ata_qc_from_tag() and is used by
libata core/EH layers to access inactive/failed qc's.
This change is applied only if the associated LLDD implements new EH
as indicated by non-NULL ->error_handler
Signed-off-by: Tejun Heo <htejun@gmail.com>
New EH may issue internal commands to recover from error while failed
qc's are still hanging around. To allow such usage, reserve tag
ATA_MAX_QUEUE-1 for internal command. This also makes it easy to tell
whether a qc is for internal command or not. ata_tag_internal() test
implements this test.
To avoid breaking existing drivers, ata_exec_internal() uses
ATA_TAG_INTERNAL only for drivers which implement ->error_handler.
For drivers using old EH, tag 0 is used. Note that this makes
ata_tag_internal() test valid only when ->error_handler is
implemented. This is okay as drivers on old EH should not and does
not have any reason to use ata_tag_internal().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add dev->ap which points back to the port the device belongs to. This
makes it unnecessary to pass @ap for silly reasons (e.g. printks).
Also, this change is necessary to accomodate later PM support which
will introduce ATA link inbetween port and device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Use new SCR and on/offline functions. Note that for LLDD which know
it implements SCR callbacks, SCR functions are guaranteed to succeed
and ata_port_online() == !ata_port_offline().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement ata_scr_{valid|read|write|write_flush}() and
ata_port_{online|offline}(). These functions replace
scr_{read|write}() and sata_dev_present().
Major difference between between the new SCR functions and the old
ones is that the new ones have a way to signal error to the caller.
This makes handling SCR-available and SCR-unavailable cases in the
same path easier. Also, it eases later PM implementation where SCR
access can fail due to various reasons.
ata_port_{online|offline}() functions return 1 only when they are
affirmitive of the condition. e.g. if SCR is unaccessible or
presence cannot be determined for other reasons, these functions
return 0. So, ata_port_online() != !ata_port_offline(). This
distinction is useful in many exception handling cases.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Init ap->cbl to ATA_CBL_SATA in ata_host_init(). This is necessary
for soon-to-follow SCR handling function changes. LLDDs are free to
change ap->cbl during probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add qc->result_tf and ATA_QCFLAG_RESULT_TF. This moves the
responsibility of loading result TF from post-compltion path to qc
execution path. qc->result_tf is loaded if explicitly requested or
the qc failsa. This allows more efficient completion implementation
and correct handling of result TF for controllers which don't have
global TF representation such as sil3124/32.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Make ata_do_reset() deal only with reset. postreset is now the
responsibility of the caller. This is simpler and eases later
prereset addition.
Signed-off-by: Tejun Heo <htejun@gmail.com>
It's not a very good idea to allocate memory during EH. Use
statically allocated buffer for dev->id[] and add 512byte buffer
ap->sector_buf. This buffer is owned by EH (or probing) and to be
used as temporary buffer for various purposes (IDENTIFY, NCQ log page
10h, PM GSCR block).
Signed-off-by: Tejun Heo <htejun@gmail.com>
ap->active_tag was cleared in ata_qc_free(). This left ap->active_tag
dangling after ata_qc_complete(). Spurious interrupts inbetween could
incorrectly access the qc. Clear active_tag in ata_qc_complete().
This change is necessary for later EH changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_bus_probe() doesn't clear dev->class after ->phy_reset(). This
can result in falsely enabled devices if probing fails. Clear
dev->class to ATA_DEV_UNKNOWN after fetching it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
While moving ata_scsi_error() from LLDD sht to libata transportt,
EXPORT_SYMBOL_GPL() entry was left out. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rename ata_down_sata_spd_limit() and friends to sata_down_spd_limit()
and likewise for simplicity & consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata needs to invoke EH without scmd. This patch adds
shost->host_eh_scheduled to implement such behavior.
Currently the only user of this feature is libata and no general
interface is defined. This patch simply adds handling for
host_eh_scheduled where needed and exports scsi_eh_wakeup() to
modules. The rest is upto libata. This is the result of the
following discussion.
http://thread.gmane.org/gmane.linux.scsi/23853/focus=9760
In short, SCSI host is not supposed to know about exceptions unrelated
to specific device or command. Such exceptions should be handled by
transport layer proper. However, the distinction is not essential to
ATA and libata is planning to depart from SCSI, so, for the time
being, libata will be using SCSI EH to handle such exceptions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Introduce scsi_req_abort_cmd(struct scsi_cmnd *).
This function requests that SCSI Core start recovery for the
command by deleting the timer and adding the command to the eh
queue. It can be called by either LLDDs or SCSI Core. LLDDs who
implement their own error recovery MAY ignore the timeout event if
they generated scsi_req_abort_cmd.
First post:
http://marc.theaimsgroup.com/?l=linux-scsi&m=113833937421677&w=2
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Problem spotted by: Suzuki K P <suzuki@in.ibm.com>
A zero return on success isn't correct for filesystem write functions.
They should either return negative error or the length of bytes
consumed. Add code to convert our zero on success error return to
return the length of bytes passed in.
This fixes the following:
$ echo "scsi remove-single-device 0 0 3 0" > /proc/scsi/scsi
bash: echo: write error: No such device or address"
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
debugged by wrwhitehead@novell.com
patch and analysis by fujita.tomonori@lab.ntt.co.jp
Only tcp_read_sock and recv_actor (iscsi_tcp_data_recv for us) see
desc.count. It is is used just for permitting tcp_read_sock to read
the portion of data in the socket.
When iscsi_tcp_data_recv sees a partial header, it sets
desc.count. However, it is possible that the next skb (containing the
rest of the header) still does not come. So I'm not sure that this
scheme is completely correct.
Ideally, we should use the exact length of the data in the socket for
desc.count. However, it is not so simple (see SIOCINQ in
tcp_ioctl). So I think that iscsi_tcp_data_recv can just stop playing
with desc.count and tell tcp_read_sock to read the all skbs. As
proposed already, if iscsi_tcp_data_ready sets desc.count to
non-zero, tcp_read_sock does that.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
debugged by Ming and Rohan:
The problem Ming and Rohan debugged was that during a normal session
login, open-iscsi is not incrementing the exp_statsn counter. It was
stuck at zero. From the RFC, it looks like if the login response PDU has
a successful status then we should be incrementing that value. Also from
the RFC, it looks like if when we drop a connection then reconnect, we
should be using the exp_statsn from the old connection in the next
relogin attempt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
align printk output
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from patmans@us.ibm.com and michaelc@cs.wisc.edu
Fix bugs when forcing a mgmt task to fail and allow
session recovery to cleanup the session/connection
of any running mgmt tasks. When called during
the in login state.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
add transport end point callbacks so iscsi drivers that cannot connect
from userspace, like iscsi tcp, using sockets do not have to
implement their own socket infrastructure.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the lpfc driver to revision 8.1.6, which includes
the following changes:
- Fix data corruption in SCSI BUS reset path, due to reusing
the same request structure for each target.
- Change version number to 8.1.6
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.
It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When abort failed, the driver gets reset handleer called. In the reset
handler, driver calls 'scsi_done()' callback for same SCSI command packet
(struct scsi_cmnd) multiple times if there are multiple SCSI command packet
in the pend_list. More over, if there are entry in the pend_lsit with
IOCTL packet associated, the driver returns it to wrong free_list so that,
in turn, the driver could end up with 'NULL pointer dereference..' during
I/O command building with incorrect resource.
Also, the patch contains several minor/cosmetic changes besides this.
Signed-off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some versions of the IBM 2104-DU3 disk enclosure
have been observed to hang Inquiries to non zero
LUNs to the SES device. This device only has LUN 0,
so this patch adds it to the BLIST to prevent scsi
core from scanning beyond LUN 0.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some pioneer DVDs are apparently returning odd "not ready" status
codes that the mid-layer doesn't recognise and so passes back to the
user as errors.
This patch overhauls our not-ready handling and adds transparent retries for:
format in progress
rebuild in progress
recalculation in progress
operation in progress
Long write in progress
self test in progress
The Pioneer was actually returning "long write in progress"
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix resource leak in
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c::ahc_linux_pci_dev_probe()
Found by the coverity checker (#668)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds AHCI support for the VIA VT8251.
Includes a workaround for a hardware bug which requires a Command List
Override before softreset.
Signed-off-by: Bastiaan Jacques <b.jacques@planet.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix ahc_pci_write_config's (wrong order of arguments).
Signed-off-by: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/megaraid.c: In function `mega_internal_command':
drivers/scsi/megaraid.c:4474: warning: unused variable `flags'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one() fails before calling request_irq() but gets to
qla2x00_free_device() then it will mistakenly try to free an irq it didn't
request. It's chosing to free based on ha->pdev->irq which is always set.
host->irq is set after request_irq() succeeds so let's use that to decide
to free or not.
This was observed and tested when a silly set of circumstances lead to
firmware loading failing on a 2100.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes coverity bug id #480. Since id_array is declared as
id_array[MAX_SLOTS], the check for i>MAX_SLOTS is obviously false.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/scsi_lib.c: In function `scsi_kmap_atomic_sg':
drivers/scsi/scsi_lib.c:2394: warning: unsigned int format, different type arg (arg 3)
drivers/scsi/scsi_lib.c:2394: warning: unsigned int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Contains the following misc fixes:
- Fix build warnings
- Race condition in lpfc_workq_post_event() could corrupt phba->work_list.
- nlp_sid was not being initialized properly
- Fix some RSCN handling during the re-discovery after Link Up event.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Additional fixes to LOGO, PLOGI, and RSCN processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix cleanup code in the lpfc_pci_probe_one() error code path.
This changes the original patch by:
- hardsetting the return value from lpfc_pci_probe_one() to
-ENODEV (negative value) if we fail attach
- removes the checks from lpfc_pci_remove_one() validating the
host and phba pointers as it's no longer needed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed FC protocol violation in handling of PRLO.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use asynchronous ABTS completion to speed up abort completions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix Discovery processing for NPorts that hit nodev_tmo during discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a NULL pointer dereference spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/scsi_scan.c: In function `scsi_probe_and_add_lun':
drivers/scsi/scsi_scan.c:926: warning: unused variable `vend'
drivers/scsi/scsi_scan.c:926: warning: unused variable `mod'
drivers/scsi/scsi_scan.c: At top level:
drivers/scsi/scsi_scan.c:829: warning: `scsi_inq_str' defined but not used
Fix those, tighten up the (somewhat poorly-designed) logging macro and fix
some coding-style warts.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current dc395x driver uses PIO to transfer up to 4 bytes which do not
get transferred by DMA (under unclear circumstances). For this the driver
uses page_address() which is broken on highmem. Apart from this the
actual calculation of the virtual address is wrong (even without highmem).
So, e.g., for reading it reads bytes from the driver to a wrong address
and returns wrong data, I guess, for writing it would just output random
data to the device.
The proper fix, as suggested by many, is to dynamically map data using
kmap_atomic(page, KM_BIO_SRC_IRQ) / kunmap_atomic(virt). The reason why it
has not been done until now, although I've done some preliminary patches
more than a year ago was that nobody interested in fixing this problem was
able to reliably reproduce it. Now it changed - with the help from
Sebastian Frei (CC'ed) I was able to trigger the PIO path. Thus, I was
also able to test and debug it.
There are 4 cases when PIO is used in dc395x - data-in / -out with and
without scatter-gather. I was able to reproduce and test only data-in with
and without SG. So, the data-out path is still untested, but it is also
somewhat simpler than the data-in. Fredrik Roubert (also CC'ed) also had
PIO triggering on his system, and in his case it was data-out without SG.
It would be great if he could test the attached patch on his system, but
even if he cannot, I would still request to apply the patch and just wait
if anybody cries...
Implementation: I put 2 new functions in scsi_lib.c and their declarations
in scsi_cmnd.h. I exported them without _GPL, although, I don't feel
strongly about that - not many drivers are likely to use them. But there
is at least one more - I want to use them in tmscsim.c. Whether these are
the right files for the functions and their declarations - not sure
either. Actually, they are not scsi-specific, so, might go somewhere
around other scattergather magic? They are not platform specific either,
and most SG functions are defined under arch/*/... As these issues were
discussed previously there were some more routines suggested to manipulate
scattergather buffers, I think, some of them were needed around
crypto code... So, might be a common place reasonable, like
lib/scattergather.c? I am open here.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert kmalloc + memset to kcalloc in ibmvscsi
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
include/scsi/scsi_devinfo.h
Same number for two BLIST flags: BLIST_MAX_512 and BLIST_ATTACH_PQ3
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This just converts iscsi_tcp to the lib
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a lot of code duplcited between iscsi_tcp
and the upcoming iscsi_iser driver. This patch puts
the duplicated code in a lib. There is more code
to move around but this takes care of the
basics. For iscsi_offload if they use the lib we will
probably move some things around. For example in the
queuecommand we will not assume that the LLD wants
to do queue_work, but it is better to handle that
later when we know for sure what iscsi_offload looks
like (we could probably do this for iscsi_iser though to).
Ideally I would like to get the iscsi_transports modules
to a place where all they really have to do is put data
on the wire, but how to do that will hopefully be more clear
when we see other modules like iscsi_offload. Or maybe
iscsi_offload will not use the lib and it will just be
iscsi_iser and iscsi_tcp and maybe the iscsi_tcp_tgt if that
is allowed in mainline.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current iscsi_tcp eh is not nicely setup for dm-multipath
and performs some extra task management functions when they
are not needed.
The attached patch:
- Fixes the TMF issues. If a session is rebuilt
then we do not send aborts.
- Fixes the problem where if the host reset fired, we would
return SUCCESS even though we had not really done anything
yet. This ends up causing problem with scsi_error.c's TUR.
- If someone has turned on the userspace nop daemon code to try
and detect network problems before the scsi command timeout
we can now drop and clean up the session before the scsi command
timesout and fires the eh speeding up the time it takes for a
command to go from one patch to another. For network problems
we fail the command with DID_BUS_BUSY so if failfast is set
scsi_decide_disposition fails the command up to dm for it to
try on another path.
- And we had to add some basic iscsi session block code. Previously
if we were trying to repair a session we would retrun a MLQUEUE code
in the queuecommand. This worked but it was not the most efficient
or pretty thing to do since it would take a while to relogin
to the target. For iscsi_tcp/open-iscsi a lot of the iscsi error handler
is in userspace the block code is pretty bare. We will be
adding to that for qla4xxx.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For iscsi boot when going from initramfs to the real root we
need to stop the userpsace iscsi daemon. To later restart it
iscsid needs to be able to rebuild itself and part of that
process is matching a session running the kernel with the
iscsid representation. To do this the attached patch
adds several required iscsi values. If the LLD does not provide
them becuase, login is done in userspace, then the transport
class and userspace set ths up for the LLD.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from hare@suse.de and michaelc@cs.wisc.edu
hw iscsi like qla4xxx does not allocate a host per session and
for userspace it is difficult to restart iscsid using the
"iscsi handles" for the session and connection, so this
patch just has the class or userspace allocate the id for
the session and connection.
Note: this breaks userspace and requires users to upgrade to the newest
open-iscsi tools. Sorry about his but open-iscsi is still too new to
say we have a stable user-kernel api and we were not good nough
designers to know that other hw iscsi drivers and iscsid itself would
need such changes. Actually we sorta did but at the time we did not
have the HW available to us so we could only guess.
Luckily, the only tools hooking into the class are the open-iscsi ones
or other tools like iscsitart hook into the open-iscsi engine from
userspace or prgroams like anaconda call our tools so they are not affected.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some devices report a peripheral qualifier of 3 for LUN 0; with the original
code, we would still try a REPORT_LUNS scan (if SCSI level is >= 3 or if we
have the BLIST_REPORTLUNS2 passed in), but NOT any sequential scan.
Also, the device at LUN 0 (which is not connected according to the PQ) is not
registered with the OS.
Unfortunately, SANs exist that are SCSI-2 and do NOT support REPORT_LUNS, but
report a unknown device with PQ 3 on LUN 0. We still need to scan them, and
most probably we even need BLIST_SPARSELUN (and BLIST_LARGELUN). See the bug
reference for an infamous example.
This is patch 3/3:
3. Implement the blacklist flag BLIST_ATTACH_PQ3 that makes the scsi
scanning code register PQ3 devices and continues scanning; only sg
will attach thanks to scsi_bus_match().
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some devices report a peripheral qualifier of 3 for LUN 0; with the original
code, we would still try a REPORT_LUNS scan (if SCSI level is >= 3 or if we
have the BLIST_REPORTLUNS2 passed in), but NOT any sequential scan.
Also, the device at LUN 0 (which is not connected according to the PQ) is not
registered with the OS.
Unfortunately, SANs exist that are SCSI-2 and do NOT support REPORT_LUNS, but
report a unknown device with PQ 3 on LUN 0. We still need to scan them, and
most probably we even need BLIST_SPARSELUN (and BLIST_LARGELUN). See the bug
reference for an infamous example.
This patch 2/3:
If a PQ3 device is found, log a message that describes the device
(INQUIRY DATA and C:B:T:U tuple) and make a suggestion for blacklisting
it.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some devices report a peripheral qualifier of 3 for LUN 0; with the original
code, we would still try a REPORT_LUNS scan (if SCSI level is >= 3 or if we
have the BLIST_REPORTLUNS2 passed in), but NOT any sequential scan.
Also, the device at LUN 0 (which is not connected according to the PQ) is not
registered with the OS.
Unfortunately, SANs exist that are SCSI-2 and do NOT support REPORT_LUNS, but
report a unknown device with PQ 3 on LUN 0. We still need to scan them, and
most probably we even need BLIST_SPARSELUN (and BLIST_LARGELUN). See the bug
reference for an infamous example.
This is patch 1/3:
If we end up in sequential scan, at least try LUN 1 for devices
that reported a PQ of 3 for LUN 0.
Also return blacklist flags, even for PQ3 devices.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Equivalent of the same patch for the 3w-xxxx driver.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_kill_request() completes requests via normal SCSI completion path
which decrements busy counts; however, requests which get passed to
scsi_kill_request() aren't holding busy counts and scsi_kill_request()
don't increment them before invoking completion path resulting in
incorrect busy counts. Bump up busy counts before invoking completion
path.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As previously reported via Michael Reed, the FC transport took a hit
in 2.6.15 (perhaps a little earlier) when we solved a recursion error.
There are 2 deadlocks occurring:
- With scan and the delete items sharing the same workq, flushing the
workq for the delete code was getting it stalled behind a very long
running scan code path.
- There's a deadlock where scsi_remove_target() has to sit behind
scsi_scan_target() due to contention over the scan_lock().
This patch resolves the 1st deadlock and significantly reduces the
odds of the second. So far, we have only replicated the 2nd deadlock
on a highly-parallel SMP system. More on the 2nd deadlock in a following
email.
This patch reworks the transport to:
- Only use the scsi host workq for scanning
- Use 2 other workq's internally. One for deletions, the other for
scheduled deletions. Originally, we tried this with a single workq,
but the occassional flushes of the scheduled queues was hitting the
second deadlock with a slightly higher frequency. In the future, we'll
look at the LLDD's and the transport to see if we can get rid of this
extra overhead.
- When moving to the other workq's we tightened up some object states
and some lock handling.
- Properly syncs adds/deletes
- minor code cleanups
- directly reference fc_host_attrs, rather than through attribute
macros
- flush the right workq on delayed work cancel failures.
Large kudos to Michael Reed who has been working this issue for the last
month.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a target is added aic79xx tries to be overly clever: it changes
the command on the fly to TEST UNIT READY and tries to requeue the
original command. Sadly this breaks SCSI compability and of course
the midlayer is getting a bit confused by it.
So we're just removing that bit of code and let the midlayer deal with
it. It's clever enough by now. And the driver code is getting simpler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's no longer needed after the convrsion to use the linux srp.h file.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As James B. correctly noted, ahd_reset_channel() in
ahd_linux_bus_reset() should be protected by ahd_lock(). However, the
main reason for not doing so was a deadlock with the interesting
polling mechanism to detect the end a bus reset.
This patch replaces the polling mechanism with a saner signalling via
flags; it also gives us the benefit of detecting any multiple calls to
ahd_reset_channel().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Ingo Flaschberger <if@xip.at>
To support the RA4100 array from Compaq.
This patch now correctly handles SCSI_UNKNOWN types with regard to
BLIST_REPORTLUNS2 (allow it) and cdb[1] LUN inclusion (don't).
It also allows a BLIST_MAX_512 flag to restrict the maximum transfer
length to 512 blocks (apparently this is an RA4100 problem).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When spinlock debugging is turned on, a struct completion grows beyond the
size allowed for the scsi_pointer. So move the struct completion back onto
the stack. The additional memory barriers are to keep us from completing
a random piece of kernel stack if the command happens to complete after
the error handling has finished.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Encapsulate some more of the device reset processing in
preparation for SATA support.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove some unused printk macros, make some more robust, and
convert some to use standard printk macros when possible.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify the dumping of the command status area by
removing some device specific information that has proven
to not be worthwhile.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixup a check used by the ipr driver to determine if a given
device is a SCSI disk. Due to the addition of support for
attaching SATA devices, this check needs to be more robust.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of NULLing the resource entry pointer when a disk
goes away to prevent any new commands being sent to it,
set the adapter resource handle to an invalid value so
new ops getting sent to it will fail with a selection timeout
response. This patch is needed for future SATA patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
when the sg driver is unable to setup direct IO, free that scatter
gather list prior to falling back to indirect IO
Further to this thread started by Bryan Holty:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114306885116728&w=2
Here is the reworked patch again. This time it has been
tested with a program provided by Bryan.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch enables clustering and sets max_sectors to 0xffff to enable
reading and writing of large blocks with tapes (and large transfers with
sg). This change is needed after the sg and st drivers started using
chained bios through scsi_request_async() in 2.6.16.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use wait_for_completion_timeout() instead of using a timer (as
Christoph Hellwig did for aic7xxx).
That lets me eliminate the sym_eh_wait structure; the struct completion,
the old_done pointer and the to_do flag can be folded into the sym_ucmd
(which overrides the scsi_pointer in scsi_cmnd).
The sym_eh_done() function becomes much simpler as the timeout handling
is done in sym_eh_handler() directly.
The host_lock can be unlocked earlier, and I cache the host in
a local variable to make accesses to it quicker.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The PDC code can set the bus mode, but we were ignoring that setting.
Also move the code that determines bus mode into its own function.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now sym2 is using spi_print_msg, we don't need to have our own messages
for IGNORE WIDE RESIDUE and MODIFY DATA POINTER, so provide the option
of passing NULL for the label.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Undef SYM_OPT_HANDLE_DEVICE_QUEUEING.
Call sym_put_start_queue instead of sym_start_next_ccbs.
Turn asserts into checks that we can send the command to the adapter,
and return busy from queuecommand if we can't.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch below is one out of a large series to mark kernel data const when
possible, goal is to use .rodata and avoid false sharing
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- to_do was never set to SYM_EH_DO_COMPLETE, so remove that code
- move the spinlocks inside the common error handler code path
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We had our own code (pci_get_base_address()) to get the bus address of
a BAR. We can get this using pcibios_resource_to_bus() instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Most of the Kconfig options for switching between IO Port and MMIO
operations use the opposite sense from sym2. Really, this option
should be set at a chipset level rather than per-driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix puts so that release functions will be called.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Fix module param
Update driver version.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
On 64 bit machines, when a 32 bit application tries to acquire the AIF,
they will always get and EFAULT error response from the driver.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Add max_channel and max_id sysfs parameters.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Since the helper thread for the driver can be killed unceremoniously by
an application, we detect the loss of the helper and restart it.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Remove superfluous code, optimize code, harden code, cast code, correct
some text, use msleep instead of schedule_timeout_interruptible. No
bugs.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
If there are no aacraid controllers, we do not create the raid
controller chrdev, thus when the driver is unloaded it performs a
superfluous deregistration.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The max_channel field is set one too large.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Some of the error return paths during initialization resulted in a zero
report to caller
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Plug and play actions resulting from event sequences shall time out if
they take longer than 30 seconds to complete.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The loss of the ownership flags, despite their flaws, in the scsi
command were sorely missed and are reinstated more accurately in the
aacraid driver to track commands and permit us to properly handle error
recovery actions.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Clean up the remaining scsi id access methods, drop ID_LUN_TO_CONTAINER
macro.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a window where we can be re-enabling an adapter, but
still allow SCSI commands to be sent to the target. This fix
sets our window (request_limit) to -1 as soon as we know the
adapter is being reenabled, and closes a very teeny tiny
window where we could set the window back to 1 before we
grab a lock.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Doug found a bug where if scsi_execute_async fails, we are leaking
sg resources. scsi_do_req never failed so we did not have to handle
that case before.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently have two implementations of this obsolete ioctl, one in
the block layer and one in the scsi code. Both of them have drawbacks.
This patch kills the scsi layer version after updating the block version
with the missing bits:
- argument checking
- use scatterlist I/O
- set number of retries based on the submitted command
This is the last user of non-S/G I/O except for the gdth driver, so
getting this in ASAP and through the scsi tree would be nie to kill
the non-S/G I/O path. Jens, what do you think about adding a check
for non-S/G I/O in the midlayer?
Thanks to Or Gerlitz for testing this patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
