Some motherboards like the Advantech ARK3400 documentation
use a non-inverted GPIO pin. We fix this by assuming that
the BIOS will set the Polarity bit for the GPIO correctly
at startup and we keep the Bit-setting intact when we start
and stop the watchdog.
Reported-by: Jean-François Deverge <jf.deverge@gmail.com>
Signed-off-by: Dave Mueller <d.mueller@elsoft.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
OMAP watchdog driver is adapted to runtime PM like a general device
driver but it is not appropriate. It is causing couple of functional
issues.
1. On OMAP4 SYSCLK can't be gated, because of issue with WDTIMER2 module,
which constantly stays in "in transition" state. Value of register
CM_WKUP_WDTIMER2_CLKCTRL is always 0x00010000 in this case.
Issue occurs immediately after first idle, when hwmod framework tries
to disable WDTIMER2 functional clock - "wd_timer2_fck". After this
module falls to "in transition" state, and SYSCLK gating is blocked.
2. Due to runtime PM, watchdog timer may be completely disabled.
In current code base watchdog timer is not disabled only because of
issue 1. Otherwise state of WDTIMER2 module will be "Disabled", and there
will be no interrupts from omap_wdt. In other words watchdog will not
work at all.
Watchdong is a special IP and it should not be disabled otherwise
purpose of it itself is defeated. Watchdog functional clock should
never be disabled. This patch updates the runtime PM handling in
driver so that runtime PM is limited only during probe/shutdown
and suspend/resume.
The patch fixes issue 1 and 2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
ie6xx_wdt_probe() calls ie6xx_wdt_debugfs_exit() as part of
it's error cleanup path, and ie6xx_wdt_debugfs_exit() is
currently annotated __devexit.
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
bcm63xx_wdt was used as a platform_driver but was not suffixed with
_driver, thus causing section mismatches, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog driver had ioctl defines introduced locally
for pre timeout handling, marked to be removed as soon as
a generic replacement would become available.
The latter has actually occurred in 2006, at e05b59fe.
Remove the local duplicates for pre timeout handling.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Do not use clock-frequency property from parent node.
Use it from watchdog node.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-By: Alejandro Cabrera <acabrera@udio.cujae.edu.cu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make sure we prepare/unprepare the COH901327 watchdog timer
as is required by the clk API especially if you use common
clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by : Pankaj Jangra <jangra.pankaj9@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Jetway JNF99 motherboard features a F71869 SuperIO chip, but its
watchdog chipset ID appears to be 1007 (as opposed to 0814). Some testing
confirmed it behaves the exact same as 0814. So add this chipset ID to the
module's ID list so that the Fintek watchdog driver can correctly identify
and access it.
Signed-off-by: Justin Wheeler <jwheeler@datademons.com>
Acked-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Asus All-In-One PC keyboard model AK1D.
BugLink: https://bugs.launchpad.net/bugs/1027789
Signed-off-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ever since the DAPM performance improvements we've been marking all widgets
as not dirty after each DAPM run. Since _PRE and _POST events aren't part
of the DAPM graph this has rendered them non-functional, they will never be
marked dirty again and thus will never be run again.
Fix this by skipping them when marking widgets as not dirty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@vger.kernel.org
Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.
And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.
How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.
1 compile
gcc -o rds_client rds_client.c
gcc -o rds_server rds_server.c
2 run ./rds_server on one console
3 run ./rds_client on another console
4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor
/***************** rds_client.c ********************/
int main(void)
{
int sock_fd;
struct sockaddr_in serverAddr;
struct sockaddr_in toAddr;
char recvBuffer[128] = "data from client";
struct msghdr msg;
struct iovec iov;
sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if (sock_fd < 0) {
perror("create socket error\n");
exit(1);
}
memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4001);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind() error\n");
close(sock_fd);
exit(1);
}
memset(&toAddr, 0, sizeof(toAddr));
toAddr.sin_family = AF_INET;
toAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
toAddr.sin_port = htons(4000);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = strlen(recvBuffer) + 1;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendto() error\n");
close(sock_fd);
exit(1);
}
printf("client send data:%s\n", recvBuffer);
memset(recvBuffer, '\0', 128);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("receive data from server:%s\n", recvBuffer);
close(sock_fd);
return 0;
}
/***************** rds_server.c ********************/
int main(void)
{
struct sockaddr_in fromAddr;
int sock_fd;
struct sockaddr_in serverAddr;
unsigned int addrLen;
char recvBuffer[128];
struct msghdr msg;
struct iovec iov;
sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if(sock_fd < 0) {
perror("create socket error\n");
exit(0);
}
memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4000);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind error\n");
close(sock_fd);
exit(1);
}
printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;
/*
* I add 16 to sizeof(fromAddr), ie 32,
* and pay attention to the definition of fromAddr,
* recvmsg() will overwrite sock_fd,
* since kernel will copy 32 bytes to userspace.
*
* If you just use sizeof(fromAddr), it works fine.
* */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}
close(sock_fd);
return 0;
}
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no OVS_SAMPLE_ATTR_ACTIONS set then "acts_list" is NULL and
it leads to a NULL dereference when we call nla_len(acts_list). This
is a static checker fix, not something I have seen in testing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP messages generated in output path if frame length is bigger than
mtu are actually lost because socket is owned by user (doing the xmit)
One example is the ipgre_tunnel_xmit() calling
icmp_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED, htonl(mtu));
We had a similar case fixed in commit a34a101e1e (ipv6: disable GSO on
sockets hitting dst_allfrag).
Problem of such fix is that it relied on retransmit timers, so short tcp
sessions paid a too big latency increase price.
This patch uses the tcp_release_cb() infrastructure so that MTU
reduction messages (ICMP messages) are not lost, and no extra delay
is added in TCP transmits.
Reported-by: Maciej Żenczykowski <maze@google.com>
Diagnosed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.
Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_tw_remember_stamp we incorrectly checked tw
instead of tm, it can lead to oops if the cached entry is
not found.
tcpm_stamp was not updated in tcpm_check_stamp when
tcpm_suck_dst was called, move the update into tcpm_suck_dst,
so that we do not call it infinitely on every next cache hit
after TCP_METRICS_TIMEOUT.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return
value to be consistent with the rest of the checks after niu_rbr_add_page()
calls in this file.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Neptune ethernet driver to check dma mapping error after map_page()
interface returns.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mpic code creates a linear revmap just big enough for all
the sources, which happens to miss the IPIs and timers on some machines.
This will in turn break when the irqdomain code loses the fallback of
doing a linear search when the revmap fails (and really slows down IPIs
otherwise).
This happens for example on the U4 based Apple machines such as the
dual core PowerMac G5s.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In net/compat.c::put_cmsg_compat() we may assign 'data' the address of
either the 'ctv' or 'cts' local variables inside the 'if
(!COMPAT_USE_64BIT_TIME)' branch.
Those variables go out of scope at the end of the 'if' statement, so
when we use 'data' further down in 'copy_to_user(CMSG_COMPAT_DATA(cm),
data, cmlen - sizeof(struct compat_cmsghdr))' there's no telling what
it may be refering to - not good.
Fix the problem by simply giving 'ctv' and 'cts' function scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
The general flow of this patch series is that first the routing cache
is removed. We build a completely new rtable entry every lookup
request.
Next we make some simplifications due to the fact that removing the
routing cache causes several members of struct rtable to become no
longer necessary.
Then we need to make some amends such that we can legally cache
pre-constructed routes in the FIB nexthops. Firstly, we need to
invalidate routes which are hit with nexthop exceptions. Secondly we
have to change the semantics of rt->rt_gateway such that zero means
that the destination is on-link and non-zero otherwise.
Now that the preparations are ready, we start caching precomputed
routes in the FIB nexthops. Output and input routes need different
kinds of care when determining if we can legally do such caching or
not. The details are in the commit log messages for those changes.
The patch series then winds down with some more struct rtable
simplifications and other tidy ups that remove unnecessary overhead.
On a SPARC-T3 output route lookups are ~876 cycles. Input route
lookups are ~1169 cycles with rpfilter disabled, and about ~1468
cycles with rpfilter enabled.
These measurements were taken with the kbench_mod test module in the
net_test_tools GIT tree:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net_test_tools.git
That GIT tree also includes a udpflood tester tool and stresses
route lookups on packet output.
For example, on the same SPARC-T3 system we can run:
time ./udpflood -l 10000000 10.2.2.11
with routing cache:
real 1m21.955s user 0m6.530s sys 1m15.390s
without routing cache:
real 1m31.678s user 0m6.520s sys 1m25.140s
Performance undoubtedly can easily be improved further.
For example fib_table_lookup() performs a lot of excessive
computations with all the masking and shifting, some of it
conditionalized to deal with edge cases.
Also, Eric's no-ref optimization for input route lookups can be
re-instated for the FIB nexthop caching code path. I would be really
pleased if someone would work on that.
In fact anyone suitable motivated can just fire up perf on the loading
of the test net_test_tools benchmark kernel module. I spend much of
my time going:
bash# perf record insmod ./kbench_mod.ko dst=172.30.42.22 src=74.128.0.1 iif=2
bash# perf report
Thanks to helpful feedback from Joe Perches, Eric Dumazet, Ben
Hutchings, and others.
Signed-off-by: David S. Miller <davem@davemloft.net>
Core:
- Rename cd-gpio to slot-gpio and extend it to support more
slot GPIO functions, such as write-protect.
- Add a function to get regulators (Vdd and Vccq) for a host.
Drivers:
- sdhci-pxav2, sdhci-pxav3: Add device tree support.
- sdhi: Add device tree support.
- sh_mmcif: Add support for regulators, device tree, slot-gpio.
- tmio: Add regulator support, use slot-gpio.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OBTA
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.6:
Core:
- Rename cd-gpio to slot-gpio and extend it to support more slot GPIO
functions, such as write-protect.
- Add a function to get regulators (Vdd and Vccq) for a host.
Drivers:
- sdhci-pxav2, sdhci-pxav3: Add device tree support.
- sdhi: Add device tree support.
- sh_mmcif: Add support for regulators, device tree, slot-gpio.
- tmio: Add regulator support, use slot-gpio."
* tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (62 commits)
mmc: sdhci-dove: Prepare for common clock framework
mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BIT
mmc: omap_hsmmc: ensure probe returns error upon resource failure
mmc: mxs-mmc: Add wp-inverted property
mmc: esdhc: Fix DMA_MASK to not break mx25 DMA access
mmc: core: reset signal voltage on power up
mmc: sd: Fix sd current limit setting
mmc: omap_hsmmc: add clk_prepare and clk_unprepare
mmc: sdhci: When a UHS switch fails, cycle power if regulator is used
mmc: atmel-mci: modify CLKDIV displaying in debugfs
mmc: atmel-mci: fix incorrect setting of host->data to NULL
mmc: sdhci: poll for card even when card is logically unremovable
mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER
mmc: sdio: Change pr_warning to pr_warn_ratelimited
mmc: core: Simplify and fix for SD switch processing
mmc: sdhci: restore host settings when card is removed
mmc: sdhci: fix incorrect command used in tuning
mmc: sdhci-pci: CaFe has broken card detection
mmc: sdhci: Report failure reasons for all cases in sdhci_add_host()
mmc: s3cmci: Convert s3cmci driver to gpiolib API
...
Pull x86/mce changes from Ingo Molnar:
"This tree improves the AMD thresholding bank code and includes a
memory fault signal handling fixlet."
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix siginfo_t->si_addr value for non-recoverable memory faults
x86, MCE, AMD: Update copyrights and boilerplate
x86, MCE, AMD: Give proper names to the thresholding banks
x86, MCE, AMD: Make error_count read only
x86, MCE, AMD: Cleanup reading of error_count
x86, MCE, AMD: Print decimal thresholding values
x86, MCE, AMD: Move shared bank to node descriptor
x86, MCE, AMD: Remove local_allocate_... wrapper
x86, MCE, AMD: Remove shared banks sysfs linking
x86, amd_nb: Export model 0x10 and later PCI id
As mach-dove is moving towards common clock framework prepare
the sdhci driver to grab its clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdio controller on dove doesn't have a bit to indicate
high-speed. With the quirk set it fixes accessing high-speed
sdcards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If platform_get_resource_by_name() fails, driver probe is aborted an
should return an error so the driver is not bound to the device.
However, in the current error path of platform_get_resource_by_name(),
probe returns zero since the return value (ret) is not properly set.
With a zero return value, the driver core assumes probe was successful
and will bind the driver to the device.
Fix this by ensuring that probe returns an error code in this failure
path.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The write-protect GPIO is inverted on some boards. Handle such case.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Patch to not set reserved bits in i.MX25 PROCTL register. DMA stops
working if those bits get set.
Signed-off-by: Wilson Callan <wilson.callan@savantsystems.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
* ACPI conversion to PM handling based on struct dev_pm_ops.
* Conversion of a number of platform drivers to PM handling based on struct
dev_pm_ops and removal of empty legacy PM callbacks from a couple of PCI
drivers.
* Suspend-to-both for in-kernel hibernation from Bojan Smojver.
* cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti U Murthy.
* cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
* Suspend and hibernate fixes from Srivatsa S. Bhat and Colin Cross.
* Generic PM domains framework updates.
* RTC CMOS wakeup signaling update from Paul Fox.
* sparse warnings fixes from Sachin Kamat.
* Build warnings fixes for the generic PM domains framework and PM sysfs code.
* sysfs switch for printing device suspend times from Sameer Nanda.
* Documentation fix from Oskar Schirmer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=vC4/
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- ACPI conversion to PM handling based on struct dev_pm_ops.
- Conversion of a number of platform drivers to PM handling based on
struct dev_pm_ops and removal of empty legacy PM callbacks from a
couple of PCI drivers.
- Suspend-to-both for in-kernel hibernation from Bojan Smojver.
- cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti
Murthy.
- cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
- Suspend and hibernate fixes from Srivatsa Bhat and Colin Cross.
- Generic PM domains framework updates.
- RTC CMOS wakeup signaling update from Paul Fox.
- sparse warnings fixes from Sachin Kamat.
- Build warnings fixes for the generic PM domains framework and PM
sysfs code.
- sysfs switch for printing device suspend times from Sameer Nanda.
- Documentation fix from Oskar Schirmer.
* tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
cpufreq: Fix sysfs deadlock with concurrent hotplug/frequency switch
EXYNOS: bugfix on retrieving old_index from freqs.old
PM / Sleep: call early resume handlers when suspend_noirq fails
PM / QoS: Use NULL pointer instead of plain integer in qos.c
PM / QoS: Use NULL pointer instead of plain integer in pm_qos.h
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
cpuilde / ACPI: remove time from acpi_processor_cx structure
cpuidle / ACPI: remove usage from acpi_processor_cx structure
cpuidle / ACPI : remove latency_ticks from acpi_processor_cx structure
rtc-cmos: report wakeups from interrupt handler
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
olpc-xo15-sci: Use struct dev_pm_ops for power management
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / crypto / ux500: Use struct dev_pm_ops for power management
PM / IPMI: Remove empty legacy PCI PM callbacks
tpm_nsc: Use struct dev_pm_ops for power management
tpm_tis: Use struct dev_pm_ops for power management
...
Pull target updates from Nicholas Bellinger:
"There have been lots of work in a number of areas this past round.
The highlights include:
- Break out target_core_cdb.c emulation into SPC/SBC ops (hch)
- Add a parse_cdb method to target backend drivers (hch)
- Move sync_cache + write_same + unmap into spc_ops (hch)
- Use target_execute_cmd for WRITEs in iscsi_target + srpt (hch)
- Offload WRITE I/O backend submission in tcm_qla2xxx + tcm_fc (hch +
nab)
- Refactor core_update_device_list_for_node() into enable/disable
funcs (agrover)
- Replace the TCM processing thread with a TMR work queue (hch)
- Fix regression in transport_add_device_to_core_hba from TMR
conversion (DanC)
- Remove racy, now-redundant check of sess_tearing_down with qla2xxx
(roland)
- Add range checking, fix reading of data len + possible underflow in
UNMAP (roland)
- Allow for target_submit_cmd() returning errors + convert fabrics
(roland + nab)
- Drop bogus struct file usage for iSCSI/SCTP (viro)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (54 commits)
iscsi-target: Drop bogus struct file usage for iSCSI/SCTP
target: NULL dereference on error path
target: Allow for target_submit_cmd() returning errors
target: Check number of unmap descriptors against our limit
target: Fix possible integer underflow in UNMAP emulation
target: Fix reading of data length fields for UNMAP commands
target: Add range checking to UNMAP emulation
target: Add generation of LOGICAL BLOCK ADDRESS OUT OF RANGE
target: Make unnecessarily global se_dev_align_max_sectors() static
target: Remove se_session.sess_wait_list
qla2xxx: Remove racy, now-redundant check of sess_tearing_down
target: Check sess_tearing_down in target_get_sess_cmd()
sbp-target: Consolidate duplicated error path code in sbp_handle_command()
target: Un-export target_get_sess_cmd()
qla2xxx: Get rid of redundant qla_tgt_sess.tearing_down
target: Make core_disable_device_list_for_node use pre-refactoring lock ordering
target: refactor core_update_device_list_for_node()
target: Eliminate else using boolean logic
target: Misc retval cleanups
target: Remove hba param from core_dev_add_lun
...
Lots and lots of fixes from Axel and some others here, plus some framework
enhancements which continue the theme of factoring code out of the drivers
and into the core.
- Initial framework support for GPIO controlled enable signals, saving a
bunch of code in drivers.
- Move fixed regulator enable time and voltage mapping table
specifications to data.
- Used some of the recent framework enhancements to make voltage change
notifications more useful, passing the voltage in as an argument to the
notification.
- Fixed the pattern used for finding individual regulators on a device
to not rely on the node name, supporting the use of multiple PMICs of
the same type in the system.
- New drivers for Maxim MAX77686, TI LP872x and LP8788, Samsung S2MPS11,
and Wolfson Arizona microphone supplies and LDOs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Nv8m
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Lots and lots of fixes from Axel and some others here, plus some
framework enhancements which continue the theme of factoring code out
of the drivers and into the core.
- Initial framework support for GPIO controlled enable signals,
saving a bunch of code in drivers.
- Move fixed regulator enable time and voltage mapping table
specifications to data.
- Used some of the recent framework enhancements to make voltage
change notifications more useful, passing the voltage in as an
argument to the notification.
- Fixed the pattern used for finding individual regulators on a
device to not rely on the node name, supporting the use of multiple
PMICs of the same type in the system.
- New drivers for Maxim MAX77686, TI LP872x and LP8788, Samsung
S2MPS11, and Wolfson Arizona microphone supplies and LDOs."
* tag 'regulator-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (176 commits)
regulator: add new lp8788 regulator driver
regulator: mc13xxx: Remove extern function declaration for mc13xxx_sw_regulator
regulator: tps65910: set input_supply on desc unconditionally
regulator: palmas: Fix calcuating selector in palmas_map_voltage_smps
regulator: lp872x: Simplify implementation of lp872x_find_regulator_init_data()
regulator: twl: Fix list_voltate for twl6030ldo_ops
regulator: twl: Convert twl6030ldo_ops to [get|set]_voltage_sel
regulator: twl: Fix the formula to calculate vsel and voltage for twl6030ldo
regulator: s5m8767: Properly handle gpio_request failure
regulator: max8997: Properly handle gpio_request failure
regulator: tps62360: use devm_* for gpio request
regulator: tps6586x: add support for input supply
regulator: tps65217: Add device tree support
regulator: aat2870: Remove unused min_uV and max_uV from struct aat2870_regulator
regulator: aat2870: Convert to regulator_list_voltage_table
regulator: da9052: initialize of_node param for regulator register
regulator: Add REGULATOR_STATUS_UNDEFINED.
regulator: Fix a typo in regulator_mode_to_status() core function.
regulator: s2mps11: Use sec_reg_write rather than sec_reg_update when mask is 0xff
regulator: s2mps11: Fix wrong setting for config.dev
...
A few fixes plus a few features, the most generally useful thing being
the register paging support which can be used by quite a few devices:
- Support for wake IRQs in regmap-irq
- Support for register paging
- Support for explicitly specified endianness, mostly for MMIO.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=uSSe
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A few fixes plus a few features, the most generally useful thing being
the register paging support which can be used by quite a few devices:
- Support for wake IRQs in regmap-irq
- Support for register paging
- Support for explicitly specified endianness, mostly for MMIO."
* tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix incorrect arguments to kzalloc() call
regmap: Add hook for printk logging for debugging during early init
regmap: Fix work_buf switching for page update during virtual range access.
regmap: Add support for register indirect addressing.
regmap: Move lock out from internal function _regmap_update_bits().
regmap: mmio: Staticize regmap_mmio_gen_context()
regmap: Remove warning on stubbed dev_get_regmap()
regmap: Implement support for wake IRQs
regmap: Don't try to map non-existant IRQs
regmap: Constify regmap_irq_chip
regmap: mmio: request native endian formatting
regmap: allow busses to request formatting with specific endianness
all we need it for is file->private_data, which is assign-once, already
assigned by that point and, incidentally, its value is already in use
by zoran ->mmap() anyway. So just store that pointer instead...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use the new custom EOF argument to generic_file_llseek_size so
that SEEK_END will go to the max hash value for htree dirs
in ext3 rather than to i_size_read()
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use the new functionality in generic_file_llseek_size() to
accept a custom EOF position, and un-cut-and-paste all the
vfs llseek code from ext4.
Also fix up comments on ext4_llseek() to reflect reality.
Signed-off-by: Eric Sandeen <sandeen@redaht.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For ext3/4 htree directories, using the vfs llseek function with
SEEK_END goes to i_size like for any other file, but in reality
we want the maximum possible hash value. Recent changes
in ext4 have cut & pasted generic_file_llseek() back into fs/ext4/dir.c,
but replicating this core code seems like a bad idea, especially
since the copy has already diverged from the vfs.
This patch updates generic_file_llseek_size to accept
both a custom maximum offset, and a custom EOF position. With this
in place, ext4_dir_llseek can pass in the appropriate maximum hash
position for both maxsize and eof, and get what it wants.
As far as I know, this does not fix any bugs - nfs in the kernel
doesn't use SEEK_END, and I don't know of any user who does. But
some ext4 folks seem keen on doing the right thing here, and I can't
really argue.
(Patch also fixes up some comments slightly)
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
wakeup_flusher_threads(0) will queue work doing complete writeback for each
flusher thread. Thus there is not much point in submitting another work doing
full inode WB_SYNC_NONE writeback by writeback_inodes_sb().
After this change it does not make sense to call nonblocking ->sync_fs and
block device flush before calling sync_inodes_sb() because
wakeup_flusher_threads() is completely asynchronous and thus these functions
would be called in parallel with inode writeback running which will effectively
void any work they do. So we move sync_inodes_sb() call before these two
functions.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It is not necessary to write block devices twice. The reason why we first did
flush and then proper sync is that
for_each_bdev() {
write_bdev()
wait_for_completion()
}
is much slower than
for_each_bdev()
write_bdev()
for_each_bdev()
wait_for_completion()
when there is bigger amount of data. But as is seen in the above, there's no real
need to scan pages and submit them twice. We just need to separate the submission
and waiting part. This patch does that.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
