This patch modifies the driver to stop depending on the clock names
being passed from the platform and switch over to bus clock lookup
using generic clock names.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
You didn't mean this to be a bool.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When SDIO runtime PM was originally introduced, we immediately faced
two regressions with two different chipsets, and in response decided
not to enable it by default.
With the recent work on the 8686 we hoped we found all the gotchas,
so 08da834 did make sense (at least experimentally).
Unfortunately we now see that some setups out there still refuse to
work when SDIO runtime PM is enabled by default (see
http://www.spinics.net/lists/linux-mmc/msg11161.html), and obviously
we can't live with these kind of regressions.
This reverts commit 08da834a24.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Drop the "state" argument from sdhci_suspend_host. Its only user is the
PCI glue; this allows to move all SDHCI glues to use dev_pm_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When getting a cmd irq during an ongoing data transfer
with dma, the dma job were never terminated. This is now
corrected.
Cc: <stable@vger.kernel.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The interrupt was previously enabled and then correctly cleared.
Now we also handle it correctly.
Cc: <stable@vger.kernel.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
mmc_suspend_host() tries to claim host during suspend
and release it only when the bus suspend operation is
compeleted. If CONFIG_MMC_UNSAFE_RESUME is defined and
the host is flagged as removable, mmc_suspend_host()
tries to remove the card. In this process, the file system
sync can get blocked trying to acquire host which is already
claimed by mmc_suspend_host() causing deadlock.
Fix this deadlock by releasing host before ->remove() is called.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that the driver is using dev_pm_ops the suspend operations in the
platform_driver structure won't get called so don't need to be there,
and certainly shouldn't be the same function as dev_pm_ops since the
signatures are different.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not power down the card in .set_ios(), unless MMC_POWER_OFF is
requested. This fixes the SDHI functionality on ecovec.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not power down the card in .set_ios(), unless MMC_POWER_OFF is
requested. This fixes the MMCIF interface functionality on ecovec boards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix wrong bus_ops->sleep check. (This isn't expected to have real-world
consequences, because the mmc core always defines both 'awake' and
'sleep' ops.)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The eMMC 4.5 devices respond to only RESET and AWAKE command in the
sleep state. Hence the mmc switch command to notify power off state
should be sent before the device enters sleep state.
This patch fixes the same.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch skips the setting of the power notify state variable
for non eMMC 4.5 devices. Also fixes the problem of omap_hsmmc
noisy/broken for suspend resume reported by Kevin Hilman.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.
This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes: drivers/mmc/host/sdhci-cns3xxx.c:110: error: 'THIS_MODULE'
undeclared here (not in a function)
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
When we can't configure the dma channel we want to fall
back to PIO. We do this by setting host->do_dma to zero.
This does not work as do_dma is used to see whether dma
can be used for the current transfer. Instead, we have
to set host->dma to NULL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add pm_caps field to omap2_hsmmc_info and omap_mmc_slot_data
structs, so we will be able to indicate mmc pm capabilities
in the board file.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an mmc card has the MMC_PM_KEEP_POWER flag, it shouldn't
be powered off on suspend (and thus doesn't have to be powered-on
on resume)
While on it, change the suspend flow a bit, to make it a bit
easier to follow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reported by Russell King:
mmcblk0: error -84 transferring data, sector 149201, nr 64,
cmd response 0x900, card status 0xb00
mmcblk0: retrying using single block read
WARNING: at lib/dma-debug.c:811 check_unmap
omap_hsmmc omap_hsmmc.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000080933000] [size=20480 bytes]
In case of an error dma_unmap() is issued in omap_hsmmc_dma_cleanup()
and then again in omap_hsmmc_post_req(). Resolve this by clearing the
host_cookie to indicate there is no DMA mapped memory to unmap.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Tested-by: Balaji T K <balajitk@ti.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This converts the remaining USB drivers in the kernel to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Till Harbaum <till@harbaum.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following error is seen in some case when mounting rootfs from
SD/MMC cards.
Waiting for root device /dev/mmcblk0p1...
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 SDC 3.74 GiB
mmcblk0: p1
mmc1: Timeout waiting for hardware interrupt.
mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 3678225
Buffer I/O error on device mmcblk0p1, logical block 458754
lost page write due to I/O error on mmcblk0p1
This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: add MAINTAINERS entries
hwspinlock/omap: omap_hwspinlock_remove should be __devexit
hwspinlock/u8500: add hwspinlock driver
hwspinlock/core: register a bank of hwspinlocks in a single API call
hwspinlock/core: remove stubs for register/unregister
hwspinlock/core: use a mutex to protect the radix tree
hwspinlock/core/omap: fix id issues on multiple hwspinlock devices
hwspinlock/omap: simplify allocation scheme
hwspinlock/core: simplify 'owner' handling
hwspinlock/core: simplify Kconfig
Fix up trivial conflicts (addition of omap_hwspinlock_pdata, removal of
omap_spinlock_latency) in arch/arm/mach-omap2/hwspinlock.c
Also, do an "evil merge" to fix a compile error in omap_hsmmc.c which
for some reason was reported in the same email thread as the "please
pull hwspinlock changes".
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
Once the implicit use of module.h is prevented, these files will
fail to find the stat.h header content.
Fix up the implicit usage expectations in advance of the cleanup.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two basic defines were everywhere, simply because module.h
was also everywhere. But we are cleaning up the latter. So make
the exporters actually call out their need for the include.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves mmc drivers to use new enum
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
Code cleanup, putting all eMMC 4.5 detection cases together.
This patch removes one if-statement and assembles all. And it also
removes variable initialization below else-statement -- all members
of card structure are already set to zero at card-init.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7131/1: clkdev: Add Common Macro for clk_lookup
clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
clk: timer-sp: convert to clk_prepare()/clk_unprepare()
clk: sa1111: convert to clk_prepare()/clk_unprepare()
clk: mmci: convert to clk_prepare()/clk_unprepare()
clk: amba-pl011: convert to clk_prepare()/clk_unprepare()
clk: amba-pl010: convert to clk_prepare()/clk_unprepare()
clk: amba-clcd: convert to clk_prepare()/clk_unprepare()
clk: amba bus: convert to clk_prepare()/clk_unprepare()
clk: provide prepare/unprepare functions
While trying to suspend the mmc host there could still be
ongoing requests that we need to wait for. At the same time
a device driver must respond to a suspend request rather quickly.
Instead of potentially wait "forever" by claiming the host we now
"try" to claim the host instead. If it fails, -EBUSY is returned.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.
This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Reported-by: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch will apply the generic CMD6 timeout to switch command
for power class.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.
This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA. It assumes 2.40a is the latest version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only allow runtime PM for devices that specifically indicate
that they support it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Go through the driver's set_power() functions rather than
calling regulator_enable/disable() directly because otherwise
pbias configuration for MMC1 is not done.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sc->clk_bus[ptr] could be NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed. During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.
For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_request_done() is sometimes called from interrupt or other atomic
context. Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request(). As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().
This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file. But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:
core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts
disabled], we run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler returns with
interrupts enabled (see commit [b738a50a: genirq: Warn when handler
enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors. Since there is no access, mmcboot0/1
devices should not be created. Add a host capability to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the power class selection feature available for mmc
versions 4.0 and above. During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Replace setup("fail_mmc_request") and faulty "ifdef KERNEL" with
a simple module_param(). The module param mmc_core.fail_request
may be used to set the fault injection attributes during boot time
or module load time.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the basic support for imx6q usdhc, which is a
derivative of esdhc controller.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is a minor fix. It makes mmc_ios_show print proper string when the
host's timing is one of the newly added UHS-I modes.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide platforms with a simplified way to specify MMCIF DMA slave IDs in
a way, similar to SDHI and other sh_dma clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error. However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC core provides a checking function that checks if the reset
has happended. Add a test to use that function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an SDHCI operation for hardware reset and connect it to the
host controller operation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC's may have a hardware reset line. This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card. Also, for MMC,
the reset is always performed before initialization.
The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The error condition indicates that mmci_post_request() should cleanup
after the mmci_pre_request(). In this case the resources allocated by
device_prep_slave_sg() are freed by calling dmaengine_terminate_all().
dma_unmap_sg() should always be performed if the host_cookie is set.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet. The err condition is not set if an MMC
request returns an error.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Earlier all cards where initiated with bus mode set as OPENDRAIN, and then
later switched to PUSHPULL. According to the MMC/SD/SDIO specifications
only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus
mode shall be PUSHPULL before attempting to init the card.
The consequence of having incorrect bus mode can lead to not being able
to detect the card. Therefore the default behavior have now been changed
to PUSHPULL in mmc_power_up, and will only be temporarily switched when
trying to attach or init a MMC card.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.
This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently if card_power_gpio is passed from platform data, it is acquired
and its value is either set or reset. After that we overwrite it with 1,
which is not required.
So, this patch removes the extra line which sets its value.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Freescale eSDHC registers only support 32-bit accesses, this patch
ensures that all Freescale eSDHC register accesses are 32-bit.
Signed-off-by: Xu lei <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend
so that Vcc (NAND core) can be cut to minimize power consumption.
eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5.
Current implemention on resume from suspend relies on CMD0 in
mmc_init_card to get out of SLEEP mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default controller configuration which was previously setup by
platform helper functions is moved into the driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Stress-testing the runtime power management of libertas_sdio
through a rmmod/insmod loop revealed that it is quite easy to
cause an ETIMEDOUT failure in mmc_sdio_power_restore() leading to:
libertas_sdio: probe of mmc1:0001:1 failed with error -16
Experimentation shows that a very short delay (100us) is needed in
the power down path before the card can be successfully booted again.
We know that this setup is lacking poweroff clamps on the card's power
lines, but as only a short delay is needed, apply this unconditionally.
Also bump up to 1ms sleep for extra legroom.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The previous patch which implemented a DT binding for sdhci-tegra did not
allow all platform data fields to be initialized from DT. The following
were missing:
is_8bit: Implemented by this patch.
pm_flags: Not implemented yet. There are no mainline users of this field.
I'm not quite sure what it's for, and hence how to represent this
in DT; the value ends up being assigned to host->mmc->pm_caps.
While we're at it, fix the binding documentation to refer to "SD/MMC"
instead of "eSDHC", since that's the correct name; "eSDHC" was cut/paste
from the Freescale binding docs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Patch adds the support for SDIO interrupts for all slots.
It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq
and the handling of the slot specific interrupts in the Interrupt Service
Routine.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If DMA resource is not available then SDCC driver
should atleast work in PIO data transfer mode.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intialize busclk_timer before it is accessed in probe.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all targets have IRQ1 line routed from the SD controller to
the processor. So we cannot rely on IRQ1 for PIO interrupts.
This patch moves all PIO interrupts to IRQ0 and enables the PIO
mode.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which
case only "cmd_irq" must be used even for PIO. With this change,
all the targets will use only "cmd_irq" for both CMD and PIO.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For clocks that support rates which can be set (most clocks other
than _pclk AHB clocks), a rate must be set using clk_set_rate()
before the clock is enabled for the first time with clk_enable().
Subsequent calls to clk_enable() need not be preceded with the
clk_set_rate() calls unless we wish to change the clock rate that
is set previously.
SDC host->clk is currently enabled without setting the clock rate
even once. This patch fixes this, by ensuring that the clock rate
for this clock is first set before enabling the clock.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This allows boards with non-standard sdio cards to fill the CIS/CCCR data.
It is particularly important for old msm72k boards using wl1251.
Also drop the obsolete embedded_sdio_data structure from the header
as it was intended to surve a similiar purpose but was not implemented.
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: Sahitya Tummala <stummala@codeaurora.org>
[davidb: minor formatting cleanup]
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of && instead of || caused a NULL pointer dereference if
gpio setup was not passed via platform data
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide separate interrupt handlers which may be used by platforms where
SDHI has three interrupt sources.
This patch also removes the commented-out handling of CRC and other errors.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This avoids the need to look up the masks each time an interrupt is handled.
As suggested by Guennadi.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning "drivers/mmc/card/queue.c:111:20: warning:
symbol 'mmc_alloc_sg' was not declared. Should it be static?"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add hooks to read gpio configuration out of the device tree node.
[grant.likely: Rewrite of original patch from John Bonesio]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[swarren: Fixed tegra_sdhci_get_ro() to retrieve pdata correctly]
[swarren: Reworked to avoid #ifdef CONFIG_OF]
[swarren: Reworked binding based on fsl-imx-esdhc.txt]
[swarren: Documented binding]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.
The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.
After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.
For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html
Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.
This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.
The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace all occurrences of CONFIG_SOC_AU1??? with runtime feature detection.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-mmc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2683/
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When indirect inclusion to <mach/hardware.h> via <mach/gpio.h> gets
removed, we will see the following compile error.
CC drivers/mmc/host/mxcmmc.o
drivers/mmc/host/mxcmmc.c: In function ‘mxcmci_init_card’:
drivers/mmc/host/mxcmmc.c:811:2: error: implicit declaration of function ‘cpu_is_mx3’
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will eventually allow <mach/gpio.h> to be deleted. This mirrors
LinusW's recent equivalent work on various other ARM platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add runtime PM support to the MMCI primecell driver, making use of
the core primecell bus runtime PM support.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
Some devices connected to the MMC bus are power controlled by external
means. For instance, an SDIO device may be powered down/up by an
external gpio line.
In order to avoid toggling power from within the MMC host driver, add a
set_power callback function, which will be called by set_ios upon
powering down/up.
Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Chris Ball <cjb@laptop.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch removes the samsung specific enum type 's3c2410_dmasrc'
and uses 'dma_data_direction' instead.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).
In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.
The current patch will clear the previous bus mode and apply the new
mode setting.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.
Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.
So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.
To prevent this from happening we use system_nrt_wq instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.
First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:
mmc_set_ios():
...
if (ios->clock > 0)
mmc_set_ungated(host);
Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.
This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:
[ 13.818610] mmc2: Timeout waiting for hardware interrupt.
[ 13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[ 13.818753] sdhci: Sys addr: 0x00000000 | Version: 0x00008901
[ 13.818804] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 13.818903] sdhci: Present: 0x1fff0000 | Host ctl: 0x00000001
[ 13.818951] sdhci: Power: 0x0000000d | Blk gap: 0x00000000
[ 13.819000] sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
[ 13.819049] sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[ 13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.819196] sdhci: Caps: 0x6bee32b2 | Caps_1: 0x00000000
[ 13.819245] sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 13.819292] sdhci: Host ctl2: 0x00000000
[ 13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[ 13.819377] sdhci: ===========================================
[ 13.919605] mmc2: Reset 0x2 never completed.
and it never recovers.
Second race might happen while running mmc_power_off():
static void mmc_power_off(struct mmc_host *host)
{
host->ios.clock = 0;
host->ios.vdd = 0;
[ clock gating kicks in here ]
/*
* Reset ocr mask to be the highest possible voltage supported for
* this mmc host. This value will be used at next power up.
*/
host->ocr = 1 << (fls(host->ocr_avail) - 1);
if (!mmc_host_is_spi(host)) {
host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
}
If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:
[ 4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[ 4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[ 4.185509] Modules linked in:
[ 4.185565]
[ 4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[ 4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[ 4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[ 4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[ 4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[ 4.186049] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[ 4.186219] Stack:
[ 4.186257] f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[ 4.186418] c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[ 4.186579] f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[ 4.186739] Call Trace:
[ 4.186802] [<c1365173>] sdhci_set_ios+0x1c3/0x340
[ 4.186883] [<c1355bd8>] mmc_gate_clock+0x68/0x120
[ 4.186963] [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[ 4.187052] [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[ 4.187134] [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[ 4.187219] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187300] [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[ 4.187379] [<c105ec82>] process_one_work+0x172/0x5b0
[ 4.187457] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187538] [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[ 4.187625] [<c105f3c8>] worker_thread+0x118/0x330
[ 4.187700] [<c1496cee>] ? preempt_schedule+0x2e/0x50
[ 4.187779] [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[ 4.187857] [<c1062cf4>] kthread+0x74/0x80
[ 4.187931] [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[ 4.188015] [<c149acfa>] kernel_thread_helper+0x6/0xd
[ 4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[ 4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[ 4.188898] ---[ end trace a7b23eecc71777e4 ]---
This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.
We prevent these by inhibiting the clock gating while we update the ios
structure.
Both problems can be reproduced by simply running the device in a reboot
loop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per suggestion by Linus Walleij:
> If you think the names of the functions are confusing then
> you may rename them, say like this:
>
> mmc_host_clk_ungate() -> mmc_host_clk_hold()
> mmc_host_clk_gate() -> mmc_host_clk_release()
>
> Which would make the usecases more clear
(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.
drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new REQ_PRIO to let requests preempt others in the cfq I/O schedule,
and lave REQ_META purely for marking requests as metadata in blktrace.
All existing callers of REQ_META except for XFS are updated to also
set REQ_PRIO for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts. This makes SDIO work.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
