Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The five-second delay can be rather annoying, and makes the system
appear much less responsive when you connect a USB drive.
It's also not entirely clear that it is needed - the settling delay has
at least historically been an issue on some Apple iPods, for example,
and some devices have been reported to need even more than the old 5s
delay.
But before we penalize them all, let's see how bad it really is. Some
of the reasons for long delays seem to be actual historical kernel bugs
that should probably never have been papered over with a delay in the
first place (there's a Ubuntu bug report for 2.6.20 about a NULL pointer
dereference unless 'delay_use' is 8 or more, for example).
It also looks like some distros have already shipped with delay_use=0,
so the five second default may well be totally historical.
In other words: "Let's see if anybody screams".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eem_wrap() is sending a sentinel CRC, but it didn't indicate that to
the host, it should zero bit 14 (bmCRC) in the EEM packet header,
instead of setting it.
Also remove a redundant crc calculation in eem_unwrap().
Signed-off-by: Steve Longerbeam <stevel@netspectrum.com>
Acked-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and
CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard,
the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c
where otg_ulpi_create is defined is not compiled.
Build error:
arch/arm/mach-mx3/built-in.o: In function `mxc_board_init':
kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create'
kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create'
This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't
use functions defined in drivers/usb/otg/otg.o and is only needed
to get ulpi.o linked into the kernel image.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_multi used CONFIG_USB_ETH_RNDIS to check if RNDIS option was requested
where it should check for CONFIG_USB_G_MULTI_RNDIS. As a result, RNDIS
was never present in g_multi regardless of configuration.
This fixes changes made in commit 396cda90d2.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After kfifo rework FHCI fails to build:
CC drivers/usb/host/fhci-tds.o
drivers/usb/host/fhci-tds.c: In function 'fhci_ep0_free':
drivers/usb/host/fhci-tds.c:108: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:118: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:128: error: used struct type value where scalar is required
This is because kfifos are no longer pointers in the ep struct.
So, instead of checking the pointers, we should now check if kfifo
is initialized.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Dell Computer Corp. Wireless 5720 VZW Mobile
Broadband (EVDO Rev-A) Minicard GPS Port. I stole the name from lsusb,
but my card does not have a GPS on it (at least not that I can make
function). I'm sure the patch is whitespace damaged but the one line
addition should be fairly straightforward nonetheless.
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB product ID of KAIREN's USB VGA Adaptor,
USB20SVGA-MB-PLUS, to sisusbvga work with it.
Signed-off-by: Tanaka Akira <akr@fsij.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. There are two msleep calls inside two spin lock sections, need to unlock
and lock again after msleep.
2. Save a extra status reg setting.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB gadget controller drivers normally export their driver registration
function, allowing modular builds of the individual gadget drivers so
do so for s3c-hsotg, fixing builds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The build of r8a66597-udc was failing on ARM since IS_ERR() and
PTR_ERR() weren't protyped. Presumably err.h is being pulled in by
another header on other platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
them by default." comment (we simply add _all_ known devices - an
enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR
The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the subclass and protocol entries from a Microtech
entry in unusual_devs.h. This was reported by <ryck@pacbell.net>.
Greg, please apply.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c
AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB. datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdf
Signed-off-by: Radek Liboska <liboska@uochb.cas.cz>
I notice that the processcompl_compat() function seems to be leaking the
'struct async *as' in the error paths.
I think that the calling convention is fundamentally buggered. The
caller is the one that did the "reap_as()" to get the as thing, the
caller should be the one to free it too.
Freeing it in the caller also means that it very clearly always gets
freed, and avoids the need for any "free in the error case too".
From: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Marcus Meissner <meissner@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to only copy the data received by the device to userspace, not
the whole kernel buffer, which can contain "stale" data.
Thanks to Marcus Meissner for pointing this out and testing the fix.
Reported-by: Marcus Meissner <meissner@suse.de>
Tested-by: Marcus Meissner <meissner@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:
r8a66597_timer() <-- lock taken
r8a66597_root_hub_control()
r8a66597_check_syssts()
usb_hcd_poll_rh_status() <-- acquires the same lock
/* insert death here */
The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:
When the HDC driver writes the data to the transfer buffers it
pollutes the D-cache (unlike DMA drivers where the device writes
the data). If the corresponding pages get mapped into user space,
there are no additional cache flushing operations performed and
this causes random user space faults on architectures with
separate I and D caches (Harvard) or those with aliasing D-cache.
This fixes up crashes during USB boot on SH7724 and others:
http://marc.info/?l=linux-sh&m=126439837308912&w=2
Reported-by: Goda Yusuke <goda.yusuke@renesas.com>
Tested-by: Goda Yusuke <goda.yusuke@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was some left over #ifdef ARM logic that is outdated but no one
really noticed. So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings. So use %zu for sizeof() values. This is a
better version of the previous commit b0a9cf297e.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resolves kernel.org bug 14914.
Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).
The patch works, but let me clarify a few things about it. All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think). I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear. Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine. Starting with
2.6.30, things no longer work.
Signed-off-by: Ryan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: Kurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost. When remote wakeup is
enabled, this is undesirable behavior.
The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.
URBs with an interval of 2 or 4 microframes aren't handled.
For the time being, the patch reduces to interval to 1 uframe.
URBs are constrained to have an interval no larger than 1024
frames by usb_submit_urb(). But some EHCI controllers allow
use of a schedule as short as 256 frames; for these
controllers we may have to decrease the interval to the
actual schedule length.
The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames. But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Glynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a regression introduced by commit
715b1dc01f ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.
Please apply it to the 2.6.33-rc* tree.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.
Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.
Fixed that. Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: pancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wTotalLength should contain the sum of the interface and unit
descriptor sizes per the Audio Device Class specification 1.0.
Reported-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 91c8a5a998 broke
compilation of this driver after it introduced
otg_init() as a static inline in <linux/usb/otg.h>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of these workarounds are already in place, but labeled as affecting
all BF52x parts. Since we have official anomaly numbers now, use those
defines. And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below array index out of bounds issue.
Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84
The data stored in 'aInfo' array exceeds the array size of 78.
This patch increases the size of this array to hold the string
correctly without any memory corruption.
This issue was reported by Klockwork tool.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following NULL pointer dereference issue.
Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.
============
Code Snippet
============
748: request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
csr &= ~(MUSB_RXCSR_AUTOCLEAR
| MUSB_RXCSR_DMAENAB
| MUSB_RXCSR_DMAMODE);
musb_writew(epio, MUSB_RXCSR,
MUSB_RXCSR_P_WZC_BITS | csr);
792: request->actual += musb_ep->dma->actual_len;
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget stalling a zero-length SETUP request results in this error message:
SetupEnd came in a wrong ep0stage idle
In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request. Add the missing '\n' to the error message itself as well...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO. Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.
Update over previous patch to avoid taking the lock if already
taken. Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.
Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a null-pointer dereference bug.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
pointer types lacks a cast
So switch to min_t(size_t, ...).
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
probe() already was on __init, so moving remove() to __exit.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
