VT is very picky about when it can enter execution.
Get all segments setup and get LDT and TR into valid state to allow
VT execution under VMware and KVM (untested).
This makes the boot decompression run under VT, which makes it several
orders of magnitude faster on 64-bit Intel hardware.
Before, I was seeing times up to a minute or more to decompress a 1.3MB kernel
on a very fast box.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 19d36ccdc3 "x86: Fix alternatives
and kprobes to remap write-protected kernel text" uses code which is
being patched for patching.
In particular, paravirt_ops does patching in two stages: first it
calls paravirt_ops.patch, then it fills any remaining instructions
with nop_out(). nop_out calls text_poke() which calls
lookup_address() which calls pgd_val() (aka paravirt_ops.pgd_val):
that call site is one of the places we patch.
If we always do patching as one single call to text_poke(), we only
need make sure we're not patching the memcpy in text_poke itself.
This means the prototype to paravirt_ops.patch needs to change, to
marshal the new code into a buffer rather than patching in place as it
does now. It also means all patching goes through text_poke(), which
is known to be safe (apply_alternatives is also changed to make a
single patch).
AK: fix compilation on x86-64 (bad rusty!)
AK: fix boot on x86-64 (sigh)
AK: merged with other patches
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out CLFLUSH support is still not complete; we
flush the wrong pages. Again disable it for the release.
Noticed by Jan Beulich who then also noticed a stupid typo later.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current code assumed that devices were directly connected to a Calgary
bridge, as it tried to get the iommu table directly from the parent bus
controller.
When we have another bridge between the Calgary/CalIOC2 bridge and the
device we should look upwards until we get to the top (Calgary/CalIOC2
bridge), where the iommu table resides.
Signed-off-by: Murillo Fernandes Bernardes <mfb@br.ibm.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some broken devices have been discovered to require %al/%ax/%eax registers
for MMIO config space accesses. Modify mmconfig.c to use these registers
explicitly (rather than modify the global readb/writeb/etc inlines).
AK: also changed i386 to always use eax
AK: moved change to extended space probing to different patch
AK: reworked with inlines according to Linus' requirements.
AK: improve comments.
Signed-off-by: dean gaudet <dean@arctic.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch finishes the i386 and x86-64 ->sysdata conversion and hopefully
also fixes Riku's and Andy's observed bugs. It is based on Yinghai Lu's
and Andy Whitcroft's patches (thanks!) with some changes:
- introduce pci_scan_bus_with_sysdata() and use it instead of
pci_scan_bus() where appropriate. pci_scan_bus_with_sysdata() will
allocate the sysdata structure and then call pci_scan_bus().
- always allocate pci_sysdata dynamically. The whole point of this
sysdata work is to make it easy to do root-bus specific things
(e.g., support PCI domains and IOMMU's). I dislike using a default
struct pci_sysdata in some places and a dynamically allocated
pci_sysdata elsewhere - the potential for someone indavertantly
changing the default structure is too high.
- this patch only makes the minimal changes necessary, i.e., the NUMA node is
always initialized to -1. Patches to do the right thing with regards
to the NUMA node can build on top of this (either add a 'node'
parameter to pci_scan_bus_with_sysdata() or just update the node
when it becomes known).
The patch was compile tested with various configurations (e.g., NUMAQ,
VISWS) and run-time tested on i386 and x86-64. Unfortunately none of my
machines exhibited the bugs so caveat emptor.
Andy, could you please see if this fixes the NUMA issues you've seen?
Riku, does this fix "pci=noacpi" on your laptop?
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: <riku.seppala@kymp.net>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code corrects the usage of the request_irq() routine.
Signed-off-by: Jay Estabrook <jay.estabrook@hp.com>
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Connect up the fallocate() system call.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have had four seperate system lockups attributable to this exact problem
in two days of testing. Instead of trying to handle all the weird end
cases and wrap, how about changing it to look for exactly what we appear
to want.
The following patch removes a couple races in setup_APIC_timer. One occurs
when the HPET advances the COUNTER past the T0_CMP value between the time
the T0_CMP was originally read and when COUNTER is read. This results in
a delay waiting for the counter to wrap. The other results from the counter
wrapping.
This change takes a snapshot of T0_CMP at the beginning of the loop and
simply loops until T0_CMP has changed (a tick has happened).
<later>
I have one small concern about the patch. I am not sure it meets the intent
as well as it should. I think we are trying to match APIC timer interrupts up
with the hpet counter increment. The event which appears to be disturbing
this loop in our test environment is the NMI watchdog. What we believe has
been happening with the existing code is the setup_APIC_timer loop has read
the CMP value, and the NMI watchdog code fires for the first time. This
results in a series of icache miss slowdowns and by the time we get back to
things it has wrapped.
I think this code is trying to get the CMP as close to the counter value as
possible. If that is the intent, maybe we should really be testing against a
"window" around the CMP. Something like COUNTER = CMP+/2. It appears COUNTER
should get advanced every 89nSec (IIRC). The above seems like an unreasonably
small window, but may be necessary. Without documentation, I am not sure of
the original intent with this code.
In summary, this code fixes my boot hangs, but since I am not certain of the
intent of the existing code, I am not certain this has not introduced new bugs
or unexpected behaviors.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: "Aaron Durbin" <adurbin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My "slices" address space management code that was added in the 2.6.22
implementation of get_unmapped_area() doesn't properly check that the
size is a multiple of the requested page size. This allows userland to
create VMAs that aren't a multiple of the huge page size with hugetlbfs
(since hugetlbfs entirely relies on get_unmapped_area() to do that
checking) which leads to a kernel BUG() when such areas are torn down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc has a couple of bugs in the usage of dma_masks that tend to
break when drivers explicitly try to set a 32-bit mask for example.
First, the code that generates the pci devices from the OF device-tree
doesn't initialize the mask properly, then our implementation of
set_dma_mask() was trying to validate the -previous- mask value, not the
one passed in as an argument.
This fixes these problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 3baee95595.
That commit was a mistake from the start; I added mdio type to the
bus scan list early on in my ucc_geth migrate to phylib development,
which is just pure wrong (the ucc_geth_mii driver creates the mii
bus and the PHY layer handles PHY enumeration without translation).
This follows on from commit 77926826f3:
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
which was basically trying to hide a symptom of the original mistake
this revert fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the Kconfig message that indicates the PS3 platform support is
incomplete.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the PS3 storage probe logic to properly find device regions on cold
startup.
o Change the storage probe event mask from notify_device_ready
to notify_region_update.
o Improve the storage probe error handling.
o Change ps3_storage_wait_for_device() to use a temporary variable to hold
the buffer address.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves affinity initialization code from spu_base.c to a
new spu_management_of_ops function (init_affinity), which is empty
in the case of PS3. This fixes a linking problem that was happening
when compiling for PS3.
Also, some small code style changes were made.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were getting a duplicate entry in the SLB shadow buffer in
slb_flush_and_rebolt() if the kernel stack was in the same segment
as PAGE_OFFSET, which on POWER6 causes the hypervisor to terminate
the partition with an error. This fixes it.
Also we were not creating an SLB entry (or an SLB shadow buffer
entry) for the kernel stack on secondary CPUs when starting the
CPU. This isn't a major problem, since an appropriate entry will
be created on demand, but this fixes that also for consistency.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Every time a cpu is added via hotplug, we allocate the per-cpu MONDO
queues but we never free them up. Freeing isn't easy since the first
cpu gets this memory from bootmem.
Therefore, the simplest thing to do to fix this bug is to allocate the
queues for all possible cpus at boot time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the cpu type in the OBP device tree before committing to
using the optimized Niagara memcpy and memset implementation.
If we don't recognize the cpu type, use a completely generic
version.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses some issues in x86/x86-64 acpi-cpufreq driver:
1. Current memory allocation for acpi_perf_data is actually open-coded
alloc_percpu(). The patch defines and handles acpi_perf_data as percpu
data. The code will be cleaner and easier to be maintained with this
change.
2. Won't load driver in acpi_cpufreq_early_init() failure case.
3. Add __init for acpi_cpufreq_early_init().
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that __initmv references the machvec section unconditionally
there have been cases where folks have been mistakenly flagging
non-machvec structures with the machvec section attribute (presumably
to shut up modpost). This leads to obscure breakage in earlyprintk
amongst other places and is rather non-obvious.
Add a simple sanity check to try and catch __initmv misuse and
panic early.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- Include atmel_lcdc.h in at91sam926{1,3}_devices.c
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the availability of the iop-adma driver iop platforms can now use
their offload engines for md-raid5 (copy+xor) and net-dma (tcp receive
copy) offload.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When generic_ptrace_peekdata() was merged, the break for these cases
ended up getting dropped, which lead to each PEEKTEXT/PEEKDATA op leaking
in to PEEKUSR and get_user_pages() always -EFAULTing. Add the break back
in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fixes for the SLB shadow buffer code
[POWERPC] Fix a compile warning in powermac/feature.c
[POWERPC] Fix a compile warning in pci_32.c
[POWERPC] Fix parse_drconf_memory() for 64-bit start addresses
[POWERPC] Fix num_cpus calculation in smp_call_function_map()
[POWERPC] ps3: Fix section mismatch in ps3/setup.c
[POWERPC] spufs: Fix affinity after introduction of node_allowed() calls
[POWERPC] Fix special PTE code for secondary hash bucket
[POWERPC] Expand RPN field to 34 bits when using 64k pages
On a machine with hardware 64kB pages and a kernel configured for a
64kB base page size, we need to change the vmalloc segment from 64kB
pages to 4kB pages if some driver creates a non-cacheable mapping in
the vmalloc area. However, we never updated with SLB shadow buffer.
This fixes it. Thanks to paulus for finding this.
Also added some write barriers to ensure the shadow buffer contents
are always consistent.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
...by using the pci_get API instead of the deprecated old stuff.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some new machines use the "ibm,dynamic-reconfiguration-memory" property
to provide memory layout information, rather than via memory nodes.
There is a bug in the code to parse this property for start addresses
over 4GB; we store the start address in an unsigned int, which means
we throw away the high bits and add apparently duplicate regions.
This results in a BUG() in free_bootmem_core(). This fixes it by
using an unsigned long instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In smp_call_function_map(), num_cpus is set to the number of online
CPUs minus one. However, if the CPU mask does not include all CPUs
(except the one we're running on), the routine will hang in the first
while() loop until the 8 second timeout occurs.
The num_cpus should be set to the number of CPUs specified in the mask
passed into the routine, after we've made any modifications to the
mask. With this change, we can also get rid of the call to
cpus_empty() and avoid adding another pass through the bitmask.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x605d4): Section mismatch: reference to
.init.text:.__alloc_bootmem (between '.prealloc' and '.ps3_power_save')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes affinity reference point placement, which was not being
done in some situations, after the introduction of node_allowed() calls.
The previously used parameter, 'ctx', is just the iterator of the
previous list_for_each_entry_reverse loop, and its value might be
invalid at the end of the loop. Also, the right context to seek
for information when defining the reference ctx location
_is_ the reference ctx.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code for mapping special 4k pages on kernels using a 64kB base
page size was missing the code for doing the RPN (real page number)
manipulation when inserting the hardware PTE in the secondary hash
bucket. It needs the same code as has already been added to the
code that inserts the HPTE in the primary hash bucket. This adds it.
Spotted by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes up the defconfig for various sh7751r based boards
by updating them to the single cpu subtype CONFIG_CPU_SUBTYPE_SH7751R.
The following sh4 boards are updated: hs7751rvoip, landisk, lboxre2,
systemh, titan.
The current defconfigs with two subtypes defined trigger a configuration
bug which result in kernel configurations with missing board support
code. We end up with kernels without board code and with generic machvec
only.
So we need this patch to make sure the board code gets compiled in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure cf support is enabled on R2D-PLUS but disabled
on R2D-1. Without this fix R2D-1 boards hang on bootup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- Disable CONFIG_SH_DMA to avoid boot up freeze on R2D-1
- Disable CONFIG_SH_STANDARD_BIOS to support R2D-PLUS boot loaders
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updated the snapgear defconfig to get a booting kernel.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a missing =m constraint to the EDD-probing code, that could have
caused improper dead-code elimination.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add memory operand constraint and write-only modifier to the inline
assembly to effect the writing of the EDID block to boot_params.edid_info.
Without this, gcc would think the EDID query was dead code and would
eliminate it.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] ITC: Reduce rating for ITC clock if ITCs are drifty
[IA64] SN2: Fix up sn2_rtc clock
[IA64] Fix wrong access to irq_desc[] in iosapic_register_intr().
[IA64] Fix possible race in destroy_and_reserve_irq()
[IA64] Fix registered interrupt check
[IA64] Remove a few duplicate includes
[IA64] Allow smp_call_function_single() to current cpu
[IA64] fix a few section mismatch warnings
Enable the MB93090 motherboard's MB86943 PCI arbiter correctly by assigning to
the register rather than comparing against it. This is required to support
bus mastering.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure to reduce the rating of the ITC clock if ITCs are drifty. If they
are drifting then we have not synchronized the ITC values, nor are we doing
the jitter compensation (useless since drift may increase the differentials
arbitrarily).
Without this patch it is possible that the ITC clock becomes selected as
the system clock on systems with drifty ITCs which will result in
nanosleep hanging.
One can still select the itc clock manually on such systems via
clocksource=itc
(Produces nice hangs on SGI Altix.)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If the sn2_rtc clock is present then it is a must have since sn2_rtc
provides a synchronized time source on Altix systems. So elevate
the priority to 450. Otherwise the ITC would take precendence. Altix
systems currently do not boot because the ITC clocksource is broken. It
seems to assume that ITCs are synchronized and as a result nanosleep
hangs (may be fixed in a different patch).
While we are at it: Remove the sn2_mc definition. The sn2_rtc has a fixed
address. No point in reading the address from memory. Removing it avoids
touching one cacheline.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In error path we must unlock irq_desc[irq].lock before we change
'irq'.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
SH-X3 has the FPU exceptions on different vectors completely,
patch in do_fpu_state_restore() to the proper vectors.
Results in a much happier userspace.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When reading the cached TTB value and extracting the pgd, we
accidentally applied a __va() to it and bumped it off in to bogus
space which ended up causing multiple faults in the error path.
Fix it up so unhandled faults don't do strange and highly unorthodox
things when oopsing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fault-nommu defines the page fault handler stubs for SH-3/4 parts,
but is not needed on SH-2/SH-2A now that the entry code has been
logically separated.
Add it in for SH-3 and SH-4 explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We were missing the trace_hardirqs_on() instrumentation in the nommu
case, resync with the MMU version of the page fault handler to have
this behaving consistently. Also explicitly re-enable IRQs now that
the assembly code isn't doing it for us any more.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the SH-3/4 TLB access violation path we were enabling IRQs before
the call in to trace_hardirqs_on(), which ended up triggering:
if (DEBUG_LOCKS_WARN_ON(!irqs_disabled()))
return;
in kernel/lockdep.c:2031. Fix this up by removing the early re-enable,
we were already re-enabling IRQs post-trace_hardirqs_on() already, so
the semantics are now as was initially intended.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] EDD: Fix the computation of the MBR sector buffer
[x86 setup] Newline after setup signature failure message
x86 boot code comments typos
C files should include the header files that prototype their functions.
Eliminates a sparse warning:
warning: symbol 'check_bugs' was not declared. Should it be static?
Signed-off-by: Josh Triplett <josh@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
C files should include the header files that prototype their functions.
Eliminates a sparse warning:
warning: symbol 'check_bugs' was not declared. Should it be static?
Signed-off-by: Josh Triplett <josh@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On make install I get the this error:
...
sh /work/crazy/linux-git/linux-2.6/arch/i386/boot/install.sh
2.6.22-g4eb6bf6b arch/i386/boot/bzImage System.map "/boot"
/work/crazy/linux-git/linux-2.6/arch/i386/boot/install.sh: line 54:
/etc/lilo/install: No such file or directory
make[1]: *** [install] Error 127
...
I don't use and don't have lilo installed on this system. The attached
patch fixes the problem for me.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/i386/kernel/apm.c: In function 'apm_init':
arch/i386/kernel/apm.c:2240: warning: format '%lx' expects type 'long
unsigned int', but argument 3 has type 'u32'
apm_info.bios.offset is of type 'u32'.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add $(LIBS_Y) to get lib/lib.a so srm_printk is present.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current 2.6.23-rc1+git, make bootimage gives the following warning while
compiling arch/alpha/boot/main.c. The patch below fixes the warning by
casting callback argument explicitly to void*. The original value comes from
START_ADDR macro and is clearly numeric so only cast it for the callback.
CC arch/alpha/boot/main.o
arch/alpha/boot/main.c: In function 'load':
arch/alpha/boot/main.c:135: warning: passing argument 3 of 'callback_read' makes pointer from integer without a cast
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current 2.6.23-rc1+git, make bootimage gives the following warnings while
compiling objstrip.c. The patch below fixes these warnings by casting strncmp
argument to char * - it does not seem feasible to change its type in struct
elfhdr.
HOSTCC arch/alpha/boot/tools/objstrip
arch/alpha/boot/tools/objstrip.c: In function 'main':
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of '__builtin_strcmp' differ in signedness
arch/alpha/boot/tools/objstrip.c:147: warning: pointer targets in passing argument 1 of 'strncmp' differ in signedness
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current 2.6.23-rc1+git, make bootimage gives the following warnings while
compiling mkbb.c. The patch below fixes these warnings by using the proper
include for exit() and using appropriate printf format.
HOSTCC arch/alpha/boot/tools/mkbb
arch/alpha/boot/tools/mkbb.c: In function 'main':
arch/alpha/boot/tools/mkbb.c:95: warning: implicit declaration of function 'exit'
arch/alpha/boot/tools/mkbb.c:95: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:102: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:110: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:117: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
arch/alpha/boot/tools/mkbb.c:118: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:125: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
arch/alpha/boot/tools/mkbb.c:126: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:143: warning: incompatible implicit declaration of built-in function 'exit'
arch/alpha/boot/tools/mkbb.c:148: warning: incompatible implicit declaration of built-in function 'exit'
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7e92b4fc34. It broke Sébastien Dugué's
machine and Jeff said (persuasively)
This seems like it will break decades-long-working stuff, in favor of
breaking new ground in our favorite area, "trusting the BIOS."
It's just not worth it for serial ports, IMO. Serial ports are something
that just shouldn't break at this late stage in the game. My new Intel
platform boxes don't even have serial ports, so I question the value of
messing with serial port probing even more... because... just wait a year,
and your box won't have a serial port either! :)
I certainly don't object to the use of platform devices (or isa_driver),
but the probe change seems questionable. That's sorta analagous to
rewriting the floppy driver probe routine. Sure you could do it... but why
risk all that damage and go through debugging all over again?
It seems clear from this report that we cannot, should not, trust BIOS for
something (a) so simple and (b) that has been working for over a decade.
Much discussion ensued and we've decided to have another go at all of this.
Cc: Sébastien Dugué <sebastien.dugue@bull.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following section mismatch warnings:
WARNING: o-alpha/vmlinux.o(.text+0x1a4d4): Section mismatch: reference to .init.text:free_area_init (between 'paging_init' and 'srm_paging_stop')
WARNING: o-alpha/vmlinux.o(.text+0x1a4dc): Section mismatch: reference to .init.text:free_area_init (between 'paging_init' and 'srm_paging_stop')
One instance of paging_init() was declared __init but not the other one -
used by defconfig. Fixed by declaring the second instance ___init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous DEBUG_SHIRQ patch missed one case. The console doesn't
set its host descriptors non-blocking.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix section mismatch warnings:
these functions are called only from __init functions.
WARNING: vmlinux.o(.text+0x1861c): Section mismatch: reference to .init.text:free_bootmem (between 'free_tce_table' and 'build_tce_table')
WARNING: vmlinux.o(.text+0x187e5): Section mismatch: reference to .init.text:__alloc_bootmem_low (between 'alloc_tce_table' and 'kretprobe_trampoline_holder')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local variable "covered" is used without initialization in i386
acpi-cpufreq driver. The initial value of covered should be 0. The bug
will cause memory leak when hit. The following patch fixes this bug.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the other archs, there is more factoring of smp call code, and more care
in the use of get_cpu(). That can be a follow-up MIPS patch.
Signed-off-by: Peter Watkins <pwatkins@sicortex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec':
arch/mips/kernel/machine_kexec.c:54: warning: assignment makes integer from pointer without a cast
arch/mips/kernel/machine_kexec.c:70: warning: assignment makes integer from pointer without a cast
arch/mips/kernel/machine_kexec.c:81: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unlike the current code suggests, the RaQ1 actually has an UART. Only
the Qube1 (Qube 2700) lacks one.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes some duplicate includes from arch/mips/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new type of irq handler remove a parameter (struct pt_regs *),but
someone forgot to supply it.
Signed-off-by: Dajie Tan <jiankemeng@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/smp.c: In function 'titan_mailbox_irq':
arch/mips/pmc-sierra/yosemite/smp.c:112: warning: 'status' may be used uninitialized in this function
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/i2c-yosemite.c: In function 'titan_i2c_xfer':
arch/mips/pmc-sierra/yosemite/i2c-yosemite.c:98: warning: 'data' may be used uninitialized in this function
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit e436d80085
Author: Ingo Molnar <mingo@elte.hu>
Date: Thu Jul 19 21:28:35 2007 +0200
[PATCH] sched: implement cpu_clock(cpu) high-speed time source
broke the build of several MIPS platforms which were already using the
symbol cpu_clock for the own purposes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
linux/arch/mips/pci/fixup-tx4938.c:21:5: warning: symbol 'pci_get_irq' was not declared. Should it be static?
linux/arch/mips/pci/fixup-tx4938.c:76: warning: passing argument 1 of 'pci_get_irq' discards qualifiers from pointer target type
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When comparing a pointer, it's clearer to compare it to NULL than to 0.
Here is an excerpt of the semantic patch:
@@
expression *E;
@@
E ==
- 0
+ NULL
@@
expression *E;
@@
E !=
- 0
+ NULL
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: akpm@linux-foundation.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some BIOSes require that sector buffers not cross 64K
boundaries. As a result, we compute a dynamic address on the
setup heap. Unfortunately, this address computation was just
totally wrong.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
End the "No setup signature found..." with a newline (the puts
routine will automatically add a carriage return.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This deals with a sun4c issue caused by commit b6a2fea393:
mm: variable length argument support.
The new way the code works means that sun4c_update_mmu_cache gets
called before a context has been selected, which results in invalid
operation of the underling mm code.
Simply ignoring update requests when there is no valid context solves
the problem.
Signed-off-by Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.23:
sh: Fix fs.h removal from mm.h regressions.
sh: fix get_wchan() for SH kernels without framepointers
sh: arch/sh/boot - fix shell usage
rtc: rtc-sh: Correct sh_rtc_set_time() for some SH-3 parts.
sh: remove support for sh7300 and solution engine 7300
sh: Add sh to the CC_OPTIMIZE_FOR_SIZE dependencies.
sh: Kill off virt_to_bus()/bus_to_virt().
sh: sh-sci - fix SH7708 support
sh: Restrict DSP support to specific CPUs.
sh: Silence sq compile warning on sh4 nommu.
sh: Kill the rest of the SE73180 cruft.
sh: remove support for sh73180 and solution engine 73180
sh: remove old broken pint code
sh: Reclaim beginning of P3 space for vmalloc area.
sh: Fix Dreamcast DMA issues.
sh: Add kmap_coherent()/kunmap_coherent() interface for SH-4.
Needs interrupt.h:
CC arch/sh64/kernel/irq_intc.o
arch/sh64/kernel/irq_intc.c: In function 'make_intc_irq':
arch/sh64/kernel/irq_intc.c:179: error: implicit declaration of function 'disable_irq_nosync'
make[1]: *** [arch/sh64/kernel/irq_intc.o] Error 1
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, destroy_and_reserve_irq() sets irq_status[irq] UNUSED using
clear_irq_vector() and sets irq_status[irq] RSVD using reserve_irq().
But there is a race window because vector_lock is once released between
them. This patch fixes this race window.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that interrupts are not initialized correctly at PCI
hotplug or driver reloading time.
By vector domain change, the iosapic_rte_info structure was changed to
be on the iosapic_intr_info[irq].rtes list even after the interrupts
are unregistered. So iosapic_intr_info[irq].rtes list must not be
checked to see if there are registered interrupts (RTEs) on the
irq. We must check iosapic_intr_info[irq].count counter instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes a few duplicate includes from arch/ia64/
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This removes the requirement for callers to get_cpu() to check in simple
cases. i386 and x86_64 already received a similar treatment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the following section mismatch warnings:
WARNING: vmlinux.o(.text+0x41902): Section mismatch: reference to .init.text:__alloc_bootmem (between 'ia64_mca_cpu_init' and 'ia64_do_tlb_purge')
WARNING: vmlinux.o(.text+0x49222): Section mismatch: reference to .init.text:__alloc_bootmem (between 'register_intr' and 'iosapic_register_intr')
WARNING: vmlinux.o(.text+0x62beb2): Section mismatch: reference to .init.text:__alloc_bootmem_node (between 'hubdev_init_node' and 'cnodeid_get_geoid')
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix show_stack() when stack argument is NULL.
[SPARC]: Fix serial console node string creation.
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
[SPARC64]: asm-sparc64/floppy.h needs linux/pci.h
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
[VIDEO]: Fix OOPS in all SBUS framebuffer drivers.
[SPARC64]: Handle mostek clock type in mini_rtc driver.
[PARTITION]: Sun/Solaris VTOC table corrections
[SPARC]: Fix floppy on some sun4c systems.
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
[PARTITION] MSDOS: Fix Sun num_partitions handling.
[SPARC]: Update defconfig.
Commit 296699de6b broke building APM
support if CONFIG_PM_SLEEP is not set.
Reported by Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Simplified a bit as suggested by Rafael. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the m32r build after the commit "Remove fs.h from mm.h"
was merged (commit 4e950f6f01).
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It didn't handle that case at all, and now dump_stack()
can be implemented directly as show_stack(current, NULL)
Signed-off-by: David S. Miller <davem@davemloft.net>
The string setting code depends upon the original value of the
"skip" variable, not the one that gets modified by the node
traversal loop.
Based upon a patch by Mark Fortescue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sclp_vt220 error handling.
[S390] cio: Reorganize initialization.
[S390] cio: Make CIO_* macros safe if dbfs are not available.
[S390] cio: Clean up messages.
[S390] Fix IRQ tracing.
[S390] vmur: fix diag14_read.
[S390] Wire up sys_fallocate.
[S390] add types.h include to s390_ext.h
[S390] cio: Remove deprecated rdc/rcd.
[S390] Get rid of new section mismatch warnings.
[S390] sclp: kill unused SCLP config option.
[S390] cio: Remove remains of _ccw_device_get_device_number().
[S390] cio: css_sch_device_register() can be made static.
[S390] Improve __smp_call_function_map.
[S390] Convert to smp_call_function_single.
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
This fixes the jornada720.c file :
* ifdef for CONFIG_SA1100_JORNADA720_SSP since we dont want to include anything not selected in menyconfig.
* add documentation for init for future reference
* change platform driver name from jornada720_mcu ->
jornada_ssp.
* change maintainer in file.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When comparing a pointer, it's clearer to compare it to NULL than to 0.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Signed-off-by: Tony Luck <tony.luck@intel.com>
b716395e2b added code to handle
a compatability issue with 32bit quota tools, but the new compat
routines are only needed when CONFIG_COMPAT=y (and with this set
to 'n' there are compilation problems since some new typedefs are
not visible).
Reported by Doug Chapman. Fix tuned by a cast of thousands (Andi,
Andreas, Arthur, HPA, Willy)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Forgot to adjust this one with the acpi autoloading patches
in commit 8c8eb78f67
Acked-by: Myron Stowe <myron.stowe@hp.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If a machine check is pending and the external or I/O interrupt handler
returns to userspace io_mcck_pending is going to call s390_handle_mcck.
Before this happens a call to TRACE_IRQS_ON was already made since we
know that we are going back to userspace and hence interrupts will be
enabled. So there was an indication that interrupts are enabled while
in reality they are still disabled.
s390_handle_mcck will do a local_irq_save/restore pair and confuse
lockdep which later complains about inconsistent irq tracing.
To solve this just call trace_hardirqs_off before calling
s390_handle_mcck and trace_hardirqs_on afterwards.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements support of fallocate system call on s390(x)
platform. A wrapper is added to address the issue which s390 ABI has with
the arguments of this system call.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no need to disable bottom halves when holding call_lock. Also
this could imply that it is legal to call smp_call_function* from
bh context, which it is not.
Also test if func will be executed locally before disabling
and aterwards enabling interrupts again. It's not necessary to disable
and enable interrupts each time __smp_call_function_map gets called.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_call_function_single now has the same semantics as s390's
smp_call_function_on. Therefore convert to the *single variant
and get rid of some architecture specific code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix wrong return value in parse_vector_domain().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64's acpi_gsi_to_irq() function assumes irq == vector. But in
fact irq can be different from vector. This patch fix this wrong
assumption.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add some sanity checks into __bind_irq_vector().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (21 commits)
[POWERPC] spusched: Fix initial timeslice calculation
[POWERPC] spufs: Fix incorrect initialization of cbe_spu_info.spus
[POWERPC] Fix Maple platform ISA bus
[POWERPC] Make pci_iounmap actually unmap things
[POWERPC] Add function to check if address is an IO port
[POWERPC] Fix Pegasos keyboard detection
[POWERPC] iSeries: Fix section mismatch warning in lpevents
[POWERPC] iSeries: Fix section mismatch warnings
[POWERPC] iSeries: We need vio_enable_interrupts
[POWERPC] Fix RTC and device tree on linkstation machines
[POWERPC] Add of_register_i2c_devices()
[POWERPC] Fix loop with unsigned long counter variable
[POWERPC] Fix register labels on show_regs() message for 4xx/Book-E
[POWERPC] Only allow building of BootX text support on PPC_MULTIPLATFORM
[POWERPC] Fix the ability to reset on MPC8544 DS and MPC8568 MDS boards
[POWERPC] Fix mpc7448hpc2 tsi108 device_type bug
[POWREPC] Fixup a number of modpost warnings on ppc32
[POWERPC] Fix ethernet PHY support on MPC8544 DS
[POWERPC] Don't try to allocate resources for a Freescale POWERPC PHB
Revert "[POWERPC] Don't complain if size-cells == 0 in prom_parse()"
...
This reverts most of commit 19d36ccdc3.
The way to DEBUG_RODATA interactions with KPROBES and CPU hotplug is to
just not mark the text as being write-protected in the first place.
Both of those facilities depend on rewriting instructions.
Having "helpful" debug facilities that just cause more problem is not
being helpful. It just adds complexity and bugs. Not worth it.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change INT0 trigger mode from edge-sense mode to level-sense mode,
in order to fix the following timeout error:
'NETDEV WATCHDOG: eth0: transmit timed out'.
This patch is required only for the Mappi platform.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following two section mismatch warnings:
WARNING: vmlinux.o(.text+0x1ce84): Section mismatch: reference to .init.text:free_bootmem (between 'free_tce_table' and 'build_tce_table')
WARNING: vmlinux.o(.text+0x1d04d): Section mismatch: reference to .init.text:__alloc_bootmem_low (between 'alloc_tce_table' and 'kretprobe_trampoline_holder')
In both cases the functions was used only from __init
context so mark them __init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function arch_vma_name() is declared weak and thus it was
not noticed that x86_64 had two almost identical implementations.
It was introduced in syscall32.c by: c633090e31
It was introduced in mm/init.c by: 2aae950b21
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following compile error introduced by
commit e8666b2718 and reported
by Alexey Dobriyan:
<-- snip -->
CC arch/i386/kernel/acpi/cstate.o
In file included from arch/i386/kernel/acpi/cstate.c:17:
include/acpi/processor.h:88: error: expected specifier-qualifier-list before 'acpi_integer'
<-- snip -->
If you select something you must ensure that the dependencies of what
you are selecting are fulfilled.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Joshua Hoblitt <jhoblitt@ifa.hawaii.edu>
Cc: Dave Jones <davej@redhat.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
u32* volatile cyclone_timer means volatile auto pointer to u32,
which is clearly not what had been intended (we never even take
the address of that variable, let alone pass it to something that
could change it behind our back). u32 volatile * is what the
authors apparently wanted to say, but in reality we don't need that
qualifier there at all - it's (properly) only passed to iomem helpers
which takes care of that stuff just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in 68328 timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in ColdFire PIT timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the unused mach_trap_init function pointer. All use of it
removed with change to using generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in ColdFire simple timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch to using the generic irq framework removed the
coldfire_trap_init() code, so remove all references to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use setup_irq() instead of request_irq() to set up system timer
in 68360 timer code. With the old m68knommu irq code this
was safe, but it is not now within the generic irq framework.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not follow the frame pointers (/proc/X/task/1/stat) unless we were
compiled with them.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the shell call to explicitly use bash, since they are bash
specific and not all systems have bash as the default.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wire up ARCH_NO_VIRT_TO_BUS, and kill off the remaining users. The
dma-mapping code really wanted virt_to_phys()/phys_to_virt() anyways,
there are no inherently special bus addresses.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all CPUs support the DSP, and this leads to problems when mixing
and matching CPU types and DSP opcodes. Fix this up by only allowing
CONFIG_SH_DSP to be enabled for the CPUs that explicitly have such a
block.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently we calculate the first timeslice for every context
incorrectly - alloc_spu_context calls spu_set_timeslice before we set
ctx->prio so we always calculate the longest possible timeslice for the
lowest possible priority.
This patch makes sure to update the schedule-related fields before
calculating the timeslice and also makes sure we update the timeslice for
a non-running context when entering spu_run so a priority change affects
the context as soon as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently initialize cbe_spu_info[].spus in both init_spu_base and
spu_sched_init. The initialise in spu_sched_init clears the SPU list,
so we end up with no physical SPUs. Because of this, the spu_run
syscall will block forever.
This change removes the unnecessary initialization in spu_sched_init.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Maple platform has ISA IOs but didn't call the new functions to
actually map those, thus crashing when trying to access the nvram.
This fixes Maple and JS2x using SLOF.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch uses the newly added functions for testing if an address is
an ISA or PCI IO port to properly unmap things in pci_iounmap that
aren't such ports. Without that, drivers using the iomap API will never
actually unmap resources, which on IBM server machines will prevent
hot-unplug of the corresponding HW adapters.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a function that tells you if a given kernel virtual address
is hitting a PCI or ISA IO port permanent mapping or not. This is to
be used in the next patch to fix iomap APIs to properly unmap things.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As of 2.6.22 the kernel doesn't recognize the i8042 keyboard/mouse
controller on the PegasosPPC. This is because of a feature/bug in the
OF device tree: the "device_type" attribute is an empty string instead
of "8042" as the kernel expects. This adds a secondary detection
which looks for a device whose *name* is "8042" if there is no device
whose *type* is "8042".
Signed-off-by: Alan Curry <pacman@world.std.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x4f568): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.setup_hvlpevent_queue' and '.process_hvlpevents')
setup_hvlpevent_queue is only called from __init code so make it __init
as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x8124): Section mismatch: reference to .init.text:.iSeries_early_setup (between '.__start_initialization_iSeries' and '.__mmu_off')
WARNING: vmlinux.o(.text+0x8128): Section mismatch: reference to .init.text:.early_setup (between '.__start_initialization_iSeries' and '.__mmu_off')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Scan the device tree for i2c devices, check their "compatible" property
against a hard-coded table, and, if found, register with i2c boardinfo.
This provides the infrastructure needed to find i2c devices in the
device tree and register them with the i2c subsystem.
This and the following commit let the linkstation work with the new i2c
API and thus fix a regression.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a possible infinite loop when the unsigned long counter "i"
is used in lmb_add_region() in the following for loop:
for (i = rgn->cnt-1; i >= 0; i--)
by making the loop counter "i" be signed.
Signed-off-by: Manish Ahuja <ahuja@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In a show_regs() message The DEAR and ESR were reported as
DAR and DSISR which only exist on classic parts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BootX text code is only supported on systems with real OF at this point
which is PPC_OF && PPC_MULTIPLATFORM.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix mpc7448hpc2 tsi108 device_type bug.
Wrong device type will break the board startup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixed the following warnings:
WARNING: vmlinux.o(.text+0x2934): Section mismatch: reference to .init.text:__alloc_bootmem (between 'irq_alloc_host' and 'irq_set_default_host')
WARNING: vmlinux.o(.text+0xb2aa): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xb2b2): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xe354): Section mismatch: reference to .init.text:__alloc_bootmem (between 'pcibios_alloc_controller' and 'pci_domain_nr')
WARNING: vmlinux.o(.text+0x12768): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x127a8): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x17566c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI PHBs actual report back values in the BAR registers
this causes issues in that we try to allocate resources for them
and will get error messages like the following on MPC8544 DS:
PCI: Failed to allocate mem resource #1:80000000@0 for 0000:00:00.0
To address this if we are class PCI_CLASS_PROCESSOR_POWERPC, a normal
header type, and the PHB we clear out all the resources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit fd6e9d3945.
Having #size-cells == 0 in a node indicates that things under the
node aren't directly accessible, and therefore we shouldn't try to
translate addresses for devices under the node into CPU physical
addresses.
Some drivers, such as the nvram driver for powermacs, rely on
of_address_to_resource failing if they are called for a node
representing a device whose resources aren't directly accessible
by the CPU. These drivers were broken by commit fd6e9d39,
resulting in the "Lombard" powerbook hanging early in the boot
process.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Nail two more simple section mismatch errors
[IA64] fix section mismatch warnings
[IA64] rename partial_page
[IA64] Ensure that machvec is set up takes place before serial console
[IA64] vector-domain - fix vector_table
[IA64] vector-domain - handle assign_irq_vector(AUTO_ASSIGN)
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
pcibios_setup (between 'pci_setup' and 'quirk_mellanox_tavor')
setup_profiling_timer (between 'write_profile' and 'delayed_put_task_struct')
Signed-off-by: Tony Luck <tony.luck@intel.com>
In 741f98fe29 Sam added full
checking across the entire vmlinux image. This flushed out
a dozen new section mismatch warnings. Start the whack-a-mole
game again to stomp them out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jens has added a partial_page thing in splice whcih conflicts with the ia64
one. Rename ia64 out of the way. (ia64 chose poorly).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make "struct ist_info" valid on both i386 and x86-64, and use the
structure by name in the setup code. Additionally, "Intel SpeedStep
IST" is redundant, refer to it as IST consistently.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For APM calls, BX contains the device index, which is zero for
the system BIOS. Disconnect requres BX = 0.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Starting with kernel 2.6.23-rc1, the i386 APM driver fails
on several of my machines with the message:
apm: BIOS not found
This happens because of a bug in the i386 boot code rewrite
from assembler to C. The original assembly code had the
following code in its APM BIOS presence test (boot/setup.S):
andw $0x02, %cx # Is 32 bit supported?
je done_apm_bios # No 32-bit, no (good) APM BIOS
That is, the code bails out if bit 2 is zero.
In the new C version, this is coded as (boot/apm.c):
if (cx & 0x02) /* 32 bits supported? */
return -1;
Here we see that the test has been accidentally inverted.
The fix is to negate the test. I've verified that this
allows the APM driver to work again on my affected machines.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Kconfig: remove CONFIG_ACPI_SLEEP from source
ACPI: quiet ACPI Exceptions due to no _PTC or _TSS
ACPI: Remove references to ACPI_STATE_S2 from acpi_pm_enter
ACPI: Kconfig: always enable CONFIG_ACPI_SLEEP on X86
ACPI: Kconfig: fold /proc/acpi/sleep under CONFIG_ACPI_PROCFS
ACPI: Kconfig: CONFIG_ACPI_PROCFS now defaults to N
ACPI: autoload modules - Create __mod_acpi_device_table symbol for all ACPI drivers
ACPI: autoload modules - Create ACPI alias interface
ACPI: autoload modules - ACPICA modifications
ACPI: asus-laptop: Fix failure exits
ACPI: fix oops due to typo in new throttling code
ACPI: ignore _PSx method for hotplugable PCI devices
ACPI: Use ACPI methods to select PCI device suspend state
ACPI, PNP: hook ACPI D-state to PNP suspend/resume
ACPI: Add acpi_pm_device_sleep_state helper routine
ACPI: Implement the set_target() callback from pm_ops
Parse the machvec command line option outside of the early_param()
so that ia64_mv is set before any console intialisation that
may result from early_param parsing.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This change fixes a panic when assign_irq_vector(irq) is called with
irq = AUTO_ASSIGN.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Intec Wildfire and WildFireMod boards.
Signed-Off-By: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is useless to preserve THREAD_SR in `resume'. The real user's sr
is actually in the stack. We also don't need to disable interrupts :
we'll never be in an invalid state, the sp switch is atomic.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add build support for the new Arcturus boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need to explicitly include linux/device.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Arcturus UC5272 and UC5282 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We didn't actually propogate the flag we pass into setup_indirect_pci()
to set indirect_type and thus were getting the wrong endianness if
PPC_INDIRECT_TYPE_BIG_ENDIAN was set.
Also, we need to or in additional flags rather than just doing a
direct assignment.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As it was a synonym for (CONFIG_ACPI && CONFIG_X86),
the ifdefs for it were more clutter than they were worth.
For ia64, just add a few stubs in anticipation of future
S3 or S4 support.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch removes old dead code:
- kill off sh73180 cpu support
- get rid of broken solution engine 73180 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The code in arch/sh/kernel/cpu/irq/pint.c doesn't compile, so let's
get rid of it to make space for a future pint implementation on top
of intc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The first 1MB of P3 space was reserved and used for page colouring,
as we've reworked that to use fixmaps, we can reclaim the space and
hand it back to VMALLOC_START.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We can't mark the whole thing init because there are dependencies
in bootloaders that assume that _start, or whatever the image
entry value, is 2 instructions before the "HdrS" signature.
In fact, TILO assumes this entry is always at 0x4000, yikes!
Also, right after the bootloader info area there are OBP strings and
values that get used later in the boot process, and those are not all
provably .init yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Sparc optimized memset (arch/sparc/lib/memset.S) does not fill last
byte of the memory area, if area size is less than 8 bytes and start
address is not word (4-bytes) aligned.
Here is code chunk where bug located:
/* %o0 - memory address, %o1 - size, %g3 - value */
8:
add %o0, 1, %o0
subcc %o1, 1, %o1
bne,a 8b
stb %g3, [%o0 - 1]
This code should write byte every loop iteration, but last time delay
instruction stb is not executed because branch instruction sets
"annul" bit.
Patch replaces bne,a by bne instruction.
Error can be reproduced by simple kernel module:
--------------------
#include <linux/module.h>
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <string.h>
static void do_memset(void **p, int size)
{
memset(p, 0x00, size);
}
static int __init memset_test_init(void)
{
char fooc[8];
int *fooi;
memset(fooc, 0xba, sizeof(fooc));
do_memset((void**)(fooc + 3), 1);
fooi = (int*) fooc;
printk("%08X %08X\n", fooi[0], fooi[1]);
return -1;
}
static void __exit memset_test_cleanup(void)
{
return;
}
module_init(memset_test_init);
module_exit(memset_test_cleanup);
MODULE_LICENSE("GPL");
EXPORT_NO_SYMBOLS;
--------------------
Signed-off-by: Alexander Shmelev <ashmelev@task.sun.mcst.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes boot failures when the build-id LD option is
actually used, because without it we end up with multiple
PT_LOAD sections which the SILO boot loader cannot handle.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'request-queue-t' of git://git.kernel.dk/linux-2.6-block:
[BLOCK] Add request_queue_t and mark it deprecated
[BLOCK] Get rid of request_queue_t typedef
