If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.
As a result gpio states are not saved/restored properly during suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
- enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards
- enable MXC nand driver
- enable UBI support
- disable cs89x0 support which broke all boards which do not have this chip
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
correct GPIO freed in treo680_irda_shutdown()
Signed-off-by: Tomáš ?ech <sleep_walker@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/plat-stmp3xxx/pinmux.c: linux/sysdev.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/plat-s3c64xx/pm.c: plat/regs-gpio.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/include/asm/atomic.h: asm/system.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/boot/compressed/misc.c: linux/compiler.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices. These devices are both interconnect
initiators and targets. Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:
Clock usbhost_48m_fck didn't enable in 100000 tries
Two bugs are fixed by this patch. First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips
should not wait for these clocks to enable. So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.
Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks. It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1]. Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.
This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].
In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.
Problem reported by Jarkko Nikula <jhnikula@gmail.com>:
http://marc.info/?l=linux-omap&m=124306184903679&w=2
...
1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
DSS case).
2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.
3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.
...
1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
(Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code. In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:
1. A clkops-specific companion clock return function (by default,
omap2_clk_dflt_find_companion())
2. A clkops-specific CM_IDLEST register address and bit shift return
function (by default, omap2_clk_dflt_find_idlest())
3. Code to wait for the CM to indicate that the module is ready
(omap2_cm_wait_idlest())
Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze. The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.
Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update the NOR flash support for TS-7200.
The TS-7200 models all have 16-bit NOR flash. Update the platform
init to support this.
Remove the private TS72XX_NOR_* defines and use the common ep93xx
defines for the external chip select physical base address instead.
Move the NOR flash registration into a static __init function. When
the NAND flash support is updated this function will also be used
to register the NAND flash for the TS-7250 and TS-7260.
Tested-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If CONFIG_APM_EMULATION=n em-x270 build fails with linker error:
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event'
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event'
make: *** [.tmp_vmlinux1] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Fix i2c_board_info definitions - we were defining the 'type' field
of these structures twice since the first argument of I2C_BOARD_INFO
sets this field. Move the second definition into I2C_BOARD_INFO().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc()
autorequest GPIO-71
Modules linked in:
[<c0028bd0>] (unwind_backtrace+0x0/0xe8) from [<c003c328>] (warn_slowpath_common+0x48/0x78)
[<c003c328>] (warn_slowpath_common+0x48/0x78) from [<c003c394>] (warn_slowpath_fmt+0x28/0x38)
[<c003c394>] (warn_slowpath_fmt+0x28/0x38) from [<c0146128>] (gpio_ensure_requested+0x58/0xbc)
[<c0146128>] (gpio_ensure_requested+0x58/0xbc) from [<c0146308>] (gpio_direction_input+0x80/0xf4)
[<c0146308>] (gpio_direction_input+0x80/0xf4) from [<c000c668>] (zylonite_pxa300_init+0x108/0x214)
[<c000c668>] (zylonite_pxa300_init+0x108/0x214) from [<c000c4e4>] (zylonite_init+0x8/0x84)
[<c000c4e4>] (zylonite_init+0x8/0x84) from [<c00097cc>] (customize_machine+0x18/0x24)
[<c00097cc>] (customize_machine+0x18/0x24) from [<c00222e0>] (do_one_initcall+0x30/0x1b0)
[<c00222e0>] (do_one_initcall+0x30/0x1b0) from [<c00083f4>] (kernel_init+0xa4/0x11c)
[<c00083f4>] (kernel_init+0xa4/0x11c) from [<c0023f3c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
This issue is caused by using gpio pin without request. Add gpio_request()
into zylonite. To simplify the code, error checking is omitted since this
is being performed early.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Removed the LBD support that isn't of any use right now at least,
then remove remnants of the TCM config flags that somehow crept
in by mistake (not yet merged patch for 2.6.32) and then the usual
defconfig noise from updated menus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the VIC resume from suspend flagged IRQ:s identical to
the flags indicating all possible interrupts. This is perhaps not
the optimal setting but setting it to 0 makes the system suspend
and never come back again (all IRQ sources masked off).
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
<linux/io.h> was getting included by <mach/ts72xx.h>, is should be
included by this file.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attepmpt to configure ULPI pins gives the following compile error:
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_AF0' undeclared here (not in a function)
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_DS01X' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-pxa/cm-x300.o] Error 1
make[1]: *** [arch/arm/mach-pxa] Error 2
make: *** [sub-make] Error 2
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Document the layout of our swp PTE entries, adding definitions for
the bit masks/shifts/sizes, and implement MAX_SWAPFILES_CHECK()
such that we fail to build if we are unable to properly encode the
swp type field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now required for libsas:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 1096 modules
ERROR: "xscale_flush_kern_dcache_page" [drivers/scsi/libsas/libsas.ko] undefined!
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As slab is available early now, use kzalloc() rather than
alloc_bootmem_low() in pxa_init_gpio_chip().
This removes the following boot time warning:
<4>------------[ cut here ]------------
<4>WARNING: at mm/bootmem.c:535 alloc_arch_preferred_bootmem+0x2c/0x54()
<d>Modules linked in:
[<c0029430>] (unwind_backtrace+0x0/0xdc) from [<c0036f64>] (warn_slowpath_common+0x4c/0x80)
[<c0036f64>] (warn_slowpath_common+0x4c/0x80) from [<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54)
[<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54) from [<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0)
[<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0) from [<c000f6e4>] (___alloc_bootmem+0xc/0x34)
[<c000f6e4>] (___alloc_bootmem+0xc/0x34) from [<c000cb20>] (pxa_init_gpio+0x48/0x228)
[<c000cb20>] (pxa_init_gpio+0x48/0x228) from [<c0009794>] (init_IRQ+0x34/0x44)
[<c0009794>] (init_IRQ+0x34/0x44) from [<c00089d4>] (start_kernel+0x144/0x264)
[<c00089d4>] (start_kernel+0x144/0x264) from [<a0008034>] (0xa0008034)
<4>---[ end trace 1b75b31a2719ed1c ]---
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In commit f23d491131, the pwr-i2c device name changed due to the
newly introduced device table. This patch fixes the clock so the
driver's probe will succeed again.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The default configuration file for the KwikByte kb9202 board was based on a 2.6.13-rc2 kernel and doesn't produce a bootable kernel. Update the
configuration in order to produce a bootable image.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a few default locks to the clocks (the clocks were used
before the locks were initialized by code), then renames the clocks
a bit to fit with the latest driver names (some changed during
review). Lastly it moves the initialization of the clock debugfs
entry to module_init() initcall level since the debugfs isn't up
in core_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This defconfig update selects all the new U300 drivers merged for
2.6.31-rc1 in the merge window and add defaults for the new
config options. It compiles and boots nicely from initramfs on
the U300.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling and wiring mode correction:
RGB wiring on the -EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the link script for ARM to use PAGE_SIZE instead of hard-
coded 4096. Also the old RODATA macro is deprecated
for the RO_DATA(PAGE_SIZE) macro. As a consequence the PAGE_SIZE
was changed from (1UL << PAGE_SHIFT) to (_AC(1,UL) << PAGE_SHIFT)
because the linker does not understand the "UL" suffix to numeric
constants.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
handle_bad_irq() expects the IRQ number to be valid (used for statistics),
so it cannot be called with an illegal vector. The problem was reported
by a static analysis tool.
The change makes bad_irq_desc redundant, so delete it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes two errors we get when building GTA02 kernel.
~ use_bbt is incorrect, we need flash_bbt.
~ We do not need .force_soft_ecc because we can unset
CONFIG_MTD_NAND_S3C2410_HWECC.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: updated patch description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit 9db41f9edc added
the .flash_bbt flag to the nand set, so add this back into
the mach-mini2440.c file (taken out on initial commit to
allow build).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 added IIS
platform devices, but these do not build on s3c24xx systems
and the file depends on SND_S3C24XX_SOC, which is selected
for all S3C64XX/S3C24XX systems.
As a quick fix, make the dev-audio.o file depends on
SND_S3C64XX_SOC_I2S instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 removed
the s3c_device_iis, but didn't replace it with anything
so a number of s3c24xx machines are currently failing
to build.
As a temporary fix, re-instate s3c_device_iis until a
proper replacement can be done for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit ec976d6eb0
removed a number of gpio definitions from <mach/hardware.h>
but misssed updating these two files:
Fix the following build errors by including <linux/gpio.h>:
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c: In function 's3c24xx_spi_gpiocfg_bus1_gpg5_6_7':
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c: In function 's3c24xx_spi_gpiocfg_bus0_gpe11_12_13':
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the MT9T031 CMOS camera sensor from Aptina to the PCM037
board. Also add two I2C iomux pin definitions, needed for pcm037. Also
remove now unneeded #ifdef CONFIG_I2C_IMX.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since recent mxc_nand driver fixes from linux-mtd this patch
add support for ST NAND02GW3B2CN6 (2k pages flash) placed on the armadillo 500
motherboard.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch add support for NOR flash mapping through the physmap driver.
The purpose is to maintain the original Atmark partition model.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove the unused CONFIG_DEBUG_S3C_PORT as we currently only have
support for using the S3C UARTs via the low-level debug code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CONFIG_S3C24XX_PWM was defined in arch/arm/plat-s3c24xx/Kconfig but
not used anywhere else as the corresponding makefile used
CONFIG_HAVE_PWM (selected by CONFIG_S3C24XX_PWM) to compile the PWM
driver.
Change the makefile to use CONFIG_S3C24XX_PWM to compile this driver
to ensure it is only build when needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some bootloader may initialize debounce register and this will make
dbclk not consist with the debounce register after linux kernel boot
up.
Signed-off-by: janboe <janboe.ye@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function flush_iotlb_page is not loading the CAM register with
the correct entry to be flushed, so it is flushing other entry
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use async timings when sync timings are not requested.
Also ensure that OneNAND is in async mode when async
timings are used.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables MStandby smart-idle mode, autoidle smartidle mode,
and the autoidle bit for DMA4_OCP_SYSCONFIG.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
SRAM size fix for HS/EMU devices
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq
is unsigned, so the error was not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which
breaks MMC3. Find the right controller to use instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the N770's MMC configuration options seem to have been
dropped. This patch adds them back in again.
Note that only the .ocr_mask change was /critical/, but I've added the
.max_freq setting back as well, as the original sources had it. Can
anyone confirm if this is unnecessary?
Secondly, there is support in the original code for a 4wire/higher
speed mode. As I don't have the requisite N770 hardware (I think it
was a rev2 N770?) to test this, I can't really add it back.
Signed-off-by: Andrew de Quincey <adq@lidskialf.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the positioning of " in MODULE_AUTHOR, which is currently
causing a build failure on latest git with CONFIG_OMAP_MBOX_FWK=m; the
original breakage appears to date from the end of last year in
a5abbbe52b7e89a7633319c5417bd4331f7ac8ed
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
[ARM] idle: clean up pm_idle calling, obey hlt_counter
[ARM] S3C: Fix gpio-config off-by-one bug
[ARM] S3C64XX: add to_irq() support for EINT() GPIO
[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
[ARM] S3C64XX: fix HCLK gate defines
[ARM] Update mach-types
[ARM] wire up rt_tgsigqueueinfo and perf_counter_open
OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
OMAP3: Add support for DPLL3 divisor values higher than 2
OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
OMAP3 SRAM: add more comments on the SRAM code
OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
OMAP3 clock: add a short delay when lowering CORE clk rate
OMAP3 clock: initialize SDRC timings at kernel start
OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
[ARM] Add old Feroceon support to compressed/head.S
[ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
[ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
[ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
...
pm_idle is used by infrastructure (eg, cpuidle) which expects architectures
to call it in a certain way. Arrange for ARM to follow x86's lead on this
and call pm_idle() with interrupts already disabled. However, we expect
pm_idle() to enable interrupts before it returns.
Also, OMAP wants to be able to disable hlt-ing, so allow hlt_counter to
prevent all calls to pm_idle.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix gpio-config off-by-one bug. Without this patch, touching GPA0 pin on
S3C64XX platform causes kernel oops.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
N group
Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A few typos seems to have sneaked into the HCLK gate defines, causing the
usb host clock to not get enabled. Fix them according to the reference
manual and throw in the 3d accel bit for good measure.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
with while (i++ < MAX_CLOCK_ENABLE_WAIT); i can reach MAX_CLOCK_ENABLE_WAIT + 1
after the loop, so if (i == MAX_CLOCK_ENABLE_WAIT) that's still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Correspondence with the TI OMAP hardware team indicates that
SDRC_DLLA_CTRL.FIXEDDELAY should be initialized to 0x0f. This number
was apparently derived from process validation. This is only used
when the SDRC DLL is unlocked (e.g., SDRC clock frequency less than
83MHz).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
