Actually, the support is already there, but it requires newer U-Boots
(to fill-in clock-frequency, and setup pin multiplexing).
Though, it appears that on RDB boards USBB pins aren't multiplexed
between USB and eSDHC (unlike MDS boards, where USB and eSDHC share
pctl and pwrfault pins).
So, for RDB boards we can safely setup pinmux and manually fill-in
clock-frequency, thus making eSDHC work even with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.
This series provides the following functionality:
- The board can boot with a serial console on UART1
- Ethernet:
UCC1 in RGMII mode
UCC2 in RGMII mode
UCC4 in RMII mode
UCC5 in RMII mode
UCC6 in RMII mode
UCC7 in RMII mode
UCC8 in RMII mode
following patch is necessary for working UCC in RMII mode:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html
- Flash accessed via MTD layer
On this hardware there is an Intel P30 flash, following patch
series is necessary for working with this hardware:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html
- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The advantages of this:
- Don't encourage legacy support;
- Less external symbols, less code to compile-in for !MPC832x_RDB
platforms.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add gpio-controller node to manage QE GPIO Bank D;
- Add mmc-spi node;
- Modify board file so that it won't use legacy SPI support with the new
device trees.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main purpose of this patch is to pass 'struct spi_device' to the chip
select handling routines. This is needed so that we could implement
full-fledged OpenFirmware support for this driver.
While at it, also:
- Replace two {de,activate}_cs routines by single cs_contol().
- Don't duplicate platform data callbacks in mpc83xx_spi struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_PPC_MULTIPLATFORM is a remain of the pre-powerpc days and isn't
really meaningful anymore. It was basically equivalent to PPC64 || 6xx.
This removes it along with the following changes:
- 32-bit platforms that relied on PPC32 && PPC_MULTIPLATFORM now rely
on 6xx which is what they want anyway.
- A new symbol, PPC_BOOK3S, is defined that represent compliance with
the "Server" variant of the architecture. This is set when either 6xx
or PPC64 is set and open the door for future BOOK3E 64-bit.
- 64-bit platforms that relied on PPC64 && PPC_MULTIPLATFORM now use
PPC64 && PPC_BOOK3S
- A separate and selectable CONFIG_PPC_OF_BOOT_TRAMPOLINE option is now
used to control the use of prom_init.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On MPC837X CPUs Dual-Role USB isn't always available (for example DR
USB pins can be muxed away to eSDHC).
U-Boot adds status = "disabled" property into the DR USB nodes to
indicate that we must not try to configure or probe Dual-Role USB,
otherwise we'll break eSDHC support on targets with MPC837X CPUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is used to help Jean Delvare to get rid of drivers/i2c/chips/
directory. The new location suggested by Kumar Gala: as the driver is
83xx specific it's placed into arch/powerpc/platforms/83xx/.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some 83xx boards were not ready for the optional QUICC Engine support.
This patch fixes following build errors:
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb308): undefined reference to `par_io_data_set'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb334): undefined reference to `par_io_data_set'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb408): undefined reference to `qe_ic_get_high_irq'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb478): undefined reference to `qe_ic_get_low_irq'
arch/powerpc/platforms/built-in.o: In function `mpc832x_spi_init':
mpc832x_rdb.c:(.init.text+0x574c): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x5768): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x5784): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x57a0): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x57bc): undefined reference to `par_io_config_pin'
arch/powerpc/platforms/built-in.o:mpc832x_rdb.c:(.init.text+0x57d8): more undefined references to `par_io_config_pin' follow
arch/powerpc/platforms/built-in.o: In function `mpc836x_rdk_init_IRQ':
mpc836x_rdk.c:(.init.text+0x5e84): undefined reference to `qe_ic_init'
arch/powerpc/platforms/built-in.o: In function `mpc836x_rdk_setup_arch':
mpc836x_rdk.c:(.init.text+0x5f10): undefined reference to `qe_reset'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes following sparse warnings:
CHECK 83xx/usb.c
83xx/usb.c:205:5: warning: symbol 'mpc837x_usb_cfg' was not declared. Should it be static?
CHECK 83xx/mpc831x_rdb.c
83xx/mpc831x_rdb.c:45:13: warning: symbol 'mpc831x_rdb_init_IRQ' was not declared. Should it be static?
CHECK 83xx/mpc832x_rdb.c
83xx/mpc832x_rdb.c:133:13: warning: symbol 'mpc832x_rdb_init_IRQ' was not declared. Should it be static?
CHECK 83xx/mpc832x_mds.c
83xx/mpc832x_mds.c:68:12: warning: Using plain integer as NULL pointer
83xx/mpc832x_mds.c:72:13: warning: incorrect type in assignment (different address spaces)
83xx/mpc832x_mds.c:72:13: expected unsigned char [usertype] *static [toplevel] bcsr_regs
83xx/mpc832x_mds.c:72:13: got void [noderef] <asn:2>*
83xx/mpc832x_mds.c:99:11: warning: incorrect type in argument 1 (different address spaces)
83xx/mpc832x_mds.c:99:11: expected void volatile [noderef] <asn:2>*addr
83xx/mpc832x_mds.c:99:11: got unsigned char [usertype] *static [toplevel] bcsr_regs
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the standalone setup the board's CPLD disables the PCI internal
arbiter, thus any access to the PCI bus will hang the board.
The common way to disable particular devices in the device tree is to
put the "status" property with any value other than "ok" or "okay"
into the device node we want to disable.
So, when there is no PCI arbiter on the bus the u-boot adds status =
"broken (no arbiter)" property into the PCI controller's node, and so
marks the PCI controller as unavailable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.
The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH). Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We must not use MPC831X_SICR[HL]_* definitions for the MPC8315 processors,
because SICR USB bits locations are not compatible with MPC8313.
This patch fixes ULPI workability on MPC8315E-RDB boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This allows other platforms with the same pci block like MPC5121 to use it.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Choosing PCI or not at config time is allowed on some
platforms via an if expression in arch/powerpc/Kconfig.
To add a new platform with PCI support selectable at
config time, you must change the if expression. This
patch makes this easier by changing:
bool "PCI support" if <long expression>
to
bool "PCI support" if PPC_PCI_CHOICE
and adding select PPC_PCI_CHOICE to all the config nodes that
were previously in the PCI if expression.
Platforms with unconditional PCI support continue to
just select PCI in their config nodes.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic PM support for 83xx. Standby is implemented as sleep.
Suspend-to-RAM is implemented as "deep sleep" (with the processor
turned off) on 831x.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There isn't any reason at this point that we can't build 82xx, 83xx & 86xx
support in with the other 6xx based boards. Twiddle the Kconfigs to allow
this.
This allows us to remove the machine type selection for related to 6xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently USB Host isn't functional on the MPC8315E boards, for two
reasons as described below.
MPC8315 Reference Manual says:
"The USB DR unit must have the same clock ratio as the encryption core
unit, unless one of them has its clock disabled."
The encryption core also drives I2C clock, so it is enabled and is equal
to 01. That means USBDRCM should be 01 here.
Plus, according to MPC8315E-RDB schematics, USB unit consumes CLK_IN
clock from the 24.00MHz oscillator, which means we must adjust REFSEL
bits as well.
p.s.
Idially we should rework whole 83xx/usb.c code, in two steps:
1. Move SCCR code to the U-Boot;
2. Implement fsl,usb-clock property in the device tree, so usb.c could
decide what clock exactly to use on per-board basis.
Though, today we're not in a hurry since there is just one 8315e board
out there.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to probe nor and nand flashes on the localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/83xx/mpc832x_rdb.c: In function ‘mpc832x_rdb_setup_arch’:
arch/powerpc/platforms/83xx/mpc832x_rdb.c:104: warning: ‘np’ is used uninitialized in this function
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '83xx' which existed only for compat with arch/ppc
* Removed Kconfig option 'PPC_MPC836x' since its not used
* Renamed Kconfig option 'MPC834x' to 'PPC_MPC834x' to match others
* Added a multiplatform 83xx defconfig (mpc83xx_defconfig).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
primarily based on mpc837x mds code.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8315 identical to mpc8313 here, just check compatible.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
prepare for adding support for the mpc8315 rdb, since they are
identical wrt platform code.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the basic support for the Wind River SBC834x boards. The
SBC8349 is more common, although it should work on the SBC8347 board
as well. Support is heavily based on the existing MPC834x_MDS code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the declarations for isa_io_base and isa_mem_base as they are declared
in pci-common.c now.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.
This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MPC837x MDS is a new member of Freescale MDS reference system.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mmc_spi has hit the mainline, so we can start using it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
