Similar to the exception queue, this hold interrupts that have been
accepted by the virtual processor core but not yet injected.
Not yet used.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The vmx code assumes that IDT-Vectoring can only be set when an exception
is injected due to the exception in question. That's not true, however:
if the exception is injected correctly, and later another exception occurs
but its delivery is blocked due to a fault, then we will incorrectly assume
the first exception was not delivered.
Fix by unconditionally dequeuing the pending exception, and requeuing it
(or the second exception) if we see it in the IDT-Vectoring field.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we're emulating an instruction, either it will succeed, in which case
any previously queued exception will be spurious, or we will requeue the
same exception.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of processing nmi injection failure in the vm entry path, move
it to the vm exit path (vm_complete_interrupts()). This separates nmi
injection from nmi post-processing, and moves the nmi state from the VT
state into vcpu state (new variable nmi_injected specifying an injection
in progress).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently most interrupt exit processing is handled on the entry path,
which is confusing. Move the NMI IRET fault processing to a new function,
vmx_complete_interrupts(), which is called on the vmexit path.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The twisty maze of conditionals can be reduced.
[joerg: fix tlb flushing]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This function injects an interrupt into the guest given the kvm struct,
the (guest) irq number and the interrupt level.
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
As suggested by Avi, introduce accessors to read/write guest registers.
This simplifies the ->cache_regs/->decache_regs interface, and improves
register caching which is important for VMX, where the cost of
vmcs_read/vmcs_write is significant.
[avi: fix warnings]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
MSR_IA32_FEATURE_LOCKED is just a bit in fact, which shouldn't be prefixed with
MSR_. So is MSR_IA32_FEATURE_VMXON_ENABLED.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
As well as discard fake accessed bit and dirty bit of EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Accesses to CR4 are intercepted even with Nested Paging enabled. But the code
does not check if the guest wants to do a global TLB flush. So this flush gets
lost. This patch adds the check and the flush to svm_set_cr4.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch introduces a guest TLB flush on every NPF exit in KVM. This fixes
random segfaults and #UD exceptions in the guest seen under some workloads
(e.g. long running compile workloads or tbench). A kernbench run with and
without that fix showed that it has a slowdown lower than 0.5%
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
They are hardware specific MSRs, and we would use them in virtualization
feature detection later.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The shadow code assigns a pte directly in one place, which is nonatomic on
i386 can can cause random memory references. Fix by using an atomic setter.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Synchronize changes to host virtual addresses which are part of
a KVM memory slot to the KVM shadow mmu. This allows pte operations
like swapping, page migration, and madvise() to transparently work
with KVM.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows reading memslots with only the mmu_lock hold for mmu
notifiers that runs in atomic context and with mmu_lock held.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows the mmu notifier code to run unalias_gfn with only the
mmu_lock held. Only alias writes need the mmu_lock held. Readers will
either take the slots_lock in read mode or the mmu_lock.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With KVM/GFP/XPMEM there isn't just the primary CPU MMU pointing to pages.
There are secondary MMUs (with secondary sptes and secondary tlbs) too.
sptes in the kvm case are shadow pagetables, but when I say spte in
mmu-notifier context, I mean "secondary pte". In GRU case there's no
actual secondary pte and there's only a secondary tlb because the GRU
secondary MMU has no knowledge about sptes and every secondary tlb miss
event in the MMU always generates a page fault that has to be resolved by
the CPU (this is not the case of KVM where the a secondary tlb miss will
walk sptes in hardware and it will refill the secondary tlb transparently
to software if the corresponding spte is present). The same way
zap_page_range has to invalidate the pte before freeing the page, the spte
(and secondary tlb) must also be invalidated before any page is freed and
reused.
Currently we take a page_count pin on every page mapped by sptes, but that
means the pages can't be swapped whenever they're mapped by any spte
because they're part of the guest working set. Furthermore a spte unmap
event can immediately lead to a page to be freed when the pin is released
(so requiring the same complex and relatively slow tlb_gather smp safe
logic we have in zap_page_range and that can be avoided completely if the
spte unmap event doesn't require an unpin of the page previously mapped in
the secondary MMU).
The mmu notifiers allow kvm/GRU/XPMEM to attach to the tsk->mm and know
when the VM is swapping or freeing or doing anything on the primary MMU so
that the secondary MMU code can drop sptes before the pages are freed,
avoiding all page pinning and allowing 100% reliable swapping of guest
physical address space. Furthermore it avoids the code that teardown the
mappings of the secondary MMU, to implement a logic like tlb_gather in
zap_page_range that would require many IPI to flush other cpu tlbs, for
each fixed number of spte unmapped.
To make an example: if what happens on the primary MMU is a protection
downgrade (from writeable to wrprotect) the secondary MMU mappings will be
invalidated, and the next secondary-mmu-page-fault will call
get_user_pages and trigger a do_wp_page through get_user_pages if it
called get_user_pages with write=1, and it'll re-establishing an updated
spte or secondary-tlb-mapping on the copied page. Or it will setup a
readonly spte or readonly tlb mapping if it's a guest-read, if it calls
get_user_pages with write=0. This is just an example.
This allows to map any page pointed by any pte (and in turn visible in the
primary CPU MMU), into a secondary MMU (be it a pure tlb like GRU, or an
full MMU with both sptes and secondary-tlb like the shadow-pagetable layer
with kvm), or a remote DMA in software like XPMEM (hence needing of
schedule in XPMEM code to send the invalidate to the remote node, while no
need to schedule in kvm/gru as it's an immediate event like invalidating
primary-mmu pte).
At least for KVM without this patch it's impossible to swap guests
reliably. And having this feature and removing the page pin allows
several other optimizations that simplify life considerably.
Dependencies:
1) mm_take_all_locks() to register the mmu notifier when the whole VM
isn't doing anything with "mm". This allows mmu notifier users to keep
track if the VM is in the middle of the invalidate_range_begin/end
critical section with an atomic counter incraese in range_begin and
decreased in range_end. No secondary MMU page fault is allowed to map
any spte or secondary tlb reference, while the VM is in the middle of
range_begin/end as any page returned by get_user_pages in that critical
section could later immediately be freed without any further
->invalidate_page notification (invalidate_range_begin/end works on
ranges and ->invalidate_page isn't called immediately before freeing
the page). To stop all page freeing and pagetable overwrites the
mmap_sem must be taken in write mode and all other anon_vma/i_mmap
locks must be taken too.
2) It'd be a waste to add branches in the VM if nobody could possibly
run KVM/GRU/XPMEM on the kernel, so mmu notifiers will only enabled if
CONFIG_KVM=m/y. In the current kernel kvm won't yet take advantage of
mmu notifiers, but this already allows to compile a KVM external module
against a kernel with mmu notifiers enabled and from the next pull from
kvm.git we'll start using them. And GRU/XPMEM will also be able to
continue the development by enabling KVM=m in their config, until they
submit all GRU/XPMEM GPLv2 code to the mainline kernel. Then they can
also enable MMU_NOTIFIERS in the same way KVM does it (even if KVM=n).
This guarantees nobody selects MMU_NOTIFIER=y if KVM and GRU and XPMEM
are all =n.
The mmu_notifier_register call can fail because mm_take_all_locks may be
interrupted by a signal and return -EINTR. Because mmu_notifier_reigster
is used when a driver startup, a failure can be gracefully handled. Here
an example of the change applied to kvm to register the mmu notifiers.
Usually when a driver startups other allocations are required anyway and
-ENOMEM failure paths exists already.
struct kvm *kvm_arch_create_vm(void)
{
struct kvm *kvm = kzalloc(sizeof(struct kvm), GFP_KERNEL);
+ int err;
if (!kvm)
return ERR_PTR(-ENOMEM);
INIT_LIST_HEAD(&kvm->arch.active_mmu_pages);
+ kvm->arch.mmu_notifier.ops = &kvm_mmu_notifier_ops;
+ err = mmu_notifier_register(&kvm->arch.mmu_notifier, current->mm);
+ if (err) {
+ kfree(kvm);
+ return ERR_PTR(err);
+ }
+
return kvm;
}
mmu_notifier_unregister returns void and it's reliable.
The patch also adds a few needed but missing includes that would prevent
kernel to compile after these changes on non-x86 archs (x86 didn't need
them by luck).
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix mm/filemap_xip.c build]
[akpm@linux-foundation.org: fix mm/mmu_notifier.c build]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an event (such as an interrupt) is injected, and the stack is
shadowed (and therefore write protected), the guest will exit. The
current code will see that the stack is shadowed and emulate a few
instructions, each time postponing the injection. Eventually the
injection may succeed, but at that time the guest may be unwilling
to accept the interrupt (for example, the TPR may have changed).
This occurs every once in a while during a Windows 2008 boot.
Fix by unshadowing the fault address if the fault was due to an event
injection.
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is no guarantee that the old TSS descriptor in the GDT contains
the proper base address. This is the case for Windows installation's
reboot-via-triplefault.
Use guest registers instead. Also translate the address properly.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The segment base is always a linear address, so translate before
accessing guest memory.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If NPT is enabled after loading both KVM modules on AMD and it should be
disabled, both KVM modules must be reloaded. If only the architecture module is
reloaded the behavior is undefined. With this patch it is possible to disable
NPT only by reloading the kvm_amd module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The direct mapped shadow code (used for real mode and two dimensional paging)
sets upper-level ptes using direct assignment rather than calling
set_shadow_pte(). A nonpae host will split this into two writes, which opens
up a race if another vcpu accesses the same memory area.
Fix by calling set_shadow_pte() instead of assigning directly.
Noticed by Izik Eidus.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the guest issues a clflush in a mmio address, the instruction
can trap into the hypervisor. Currently, we do not decode clflush
properly, causing the guest to hang. This patch fixes this emulating
clflush (opcode 0f ae).
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Harden kvm_mmu_zap_page() against invalid root pages that
had been shadowed from memslots that are gone.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Flush the shadow mmu before removing regions to avoid stale entries.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch fixes issue encountered with HLT instruction
under FreeDOS's HIMEM XMS Driver.
The HLT instruction jumped directly to the done label and
skips updating the EIP value, therefore causing the guest
to spin endlessly on the same instruction.
The patch changes the instruction so that it writes back
the updated EIP value.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Fix a potention issue caused by kvm_mmu_slot_remove_write_access(). The
old behavior don't sync EPT TLB with modified EPT entry, which result
in inconsistent content of EPT TLB and EPT table.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_mmu_zap_page() needs slots lock held (rmap_remove->gfn_to_memslot,
for example).
Since kvm_lock spinlock is held in mmu_shrink(), do a non-blocking
down_read_trylock().
Untested.
Signed-off-by: Avi Kivity <avi@qumranet.com>
On suspend the svm_hardware_disable function is called which frees all svm_data
variables. On resume they are not re-allocated. This patch removes the
deallocation of svm_data from the hardware_disable function to the
hardware_unsetup function which is not called on suspend.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is no need to grab slots_lock if the vapic_page will not
be touched.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Older linux guests (in this case, 2.6.9) can attempt to
access the performance counter MSRs without a fixup section, and injecting
a GPF kills the guest. Work around by allowing the guest to write those MSRs.
Tested by me on RHEL-4 i386 and x86_64 guests, as well as F-9 guests.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The function ept_update_paging_mode_cr0() write to
CPU_BASED_VM_EXEC_CONTROL based on vmcs_config.cpu_based_exec_ctrl. That's
wrong because the variable may not consistent with the content in the
CPU_BASE_VM_EXEC_CONTROL MSR.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of prefetching all segment bases before emulation, read them at the
last moment. Since most of them are unneeded, we save some cycles on
Intel machines where this is a bit expensive.
Signed-off-by: Avi Kivity <avi@qumranet.com>
rip relative decoding is relative to the instruction pointer of the next
instruction; by moving address adjustment until after decoding is complete,
we remove the need to determine the instruction size.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we're not gonna do anything (case in which failure is already
reported), we do not need to even bother with calculating the linear rip.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Only abort guest entry if the timer count went from 0->1, since for 1->2
or larger the bit will either be set already or a timer irq will have
been injected.
Using atomic_inc_and_test() for it also introduces an SMP barrier
to the LAPIC version (thought it was unecessary because of timer
migration, but guest can be scheduled to a different pCPU between exit
and kvm_vcpu_block(), so there is the possibility for a race).
Noticed by Avi.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables coalesced MMIO for x86 architecture.
It defines KVM_MMIO_PAGE_OFFSET and KVM_CAP_COALESCED_MMIO.
It enables the compilation of coalesced_mmio.c.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Modify member in_range() of structure kvm_io_device to pass length and the type
of the I/O (write or read).
This modification allows to use kvm_io_device with coalesced MMIO.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
SVM cannot benefit from page prefetching since guest page fault bypass
cannot by made to work there. Avoid accessing the guest page table in
this case.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Encountered in FC6 boot sequence, now that we don't force ss.rpl = 0 during
the protected mode transition. Not really necessary, but nice to have.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add support for mov r, sreg (0x8c) instruction.
[avi: drop the sreg decoding table in favor of 1:1 encoding]
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add support for jmp far (opcode 0xea) instruction.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Update c->dst.bytes in decode instruction instead of instruction
itself. It's needed because if c->dst.bytes is equal to 0, the
instruction is not emulated.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Prefixes functions that will be exported with kvm_.
We also prefixed set_segment() even if it still static
to be coherent.
signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add emulation for the memory type range registers, needed by VMware esx 3.5,
and by pci device assignment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
VMX hardware can cache the contents of a vcpu's vmcs. This cache needs
to be flushed when migrating a vcpu to another cpu, or (which is the case
that interests us here) when disabling hardware virtualization on a cpu.
The current implementation of decaching iterates over the list of all vcpus,
picks the ones that are potentially cached on the cpu that is being offlined,
and flushes the cache. The problem is that it uses mutex_trylock() to gain
exclusive access to the vcpu, which fires off a (benign) warning about using
the mutex in an interrupt context.
To avoid this, and to make things generally nicer, add a new per-cpu list
of potentially cached vcus. This makes the decaching code much simpler. The
list is vmx-specific since other hardware doesn't have this issue.
[andrea: fix crash on suspend/resume]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM turns off hardware virtualization extensions during reboot, in order
to disassociate the memory used by the virtualization extensions from the
processor, and in order to have the system in a consistent state.
Unfortunately virtual machines may still be running while this goes on,
and once virtualization extensions are turned off, any virtulization
instruction will #UD on execution.
Fix by adding an exception handler to virtualization instructions; if we get
an exception during reboot, we simply spin waiting for the reset to complete.
If it's a true exception, BUG() so we can have our stack trace.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The KVM MMU tries to detect when a speculative pte update is not actually
used by demand fault, by checking the accessed bit of the shadow pte. If
the shadow pte has not been accessed, we deem that page table flooded and
remove the shadow page table, allowing further pte updates to proceed
without emulation.
However, if the pte itself points at a page table and only used for write
operations, the accessed bit will never be set since all access will happen
through the emulator.
This is exactly what happens with kscand on old (2.4.x) HIGHMEM kernels.
The kernel points a kmap_atomic() pte at a page table, and then
proceeds with read-modify-write operations to look at the dirty and accessed
bits. We get a false flood trigger on the kmap ptes, which results in the
mmu spending all its time setting up and tearing down shadows.
Fix by setting the shadow accessed bit on emulated accesses.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Attached is a patch that fixes a guest crash when booting older Linux kernels.
The problem stems from the fact that we are currently emulating
MSR_K7_EVNTSEL[0-3], but not emulating MSR_K7_PERFCTR[0-3]. Because of this,
setup_k7_watchdog() in the Linux kernel receives a GPF when it attempts to
write into MSR_K7_PERFCTR, which causes an OOPs.
The patch fixes it by just "fake" emulating the appropriate MSRs, throwing
away the data in the process. This causes the NMI watchdog to not actually
work, but it's not such a big deal in a virtualized environment.
When we get a write to one of these counters, we printk_ratelimit() a warning.
I decided to print it out for all writes, even if the data is 0; it doesn't
seem to make sense to me to special case when data == 0.
Tested by myself on a RHEL-4 guest, and Joerg Roedel on a Windows XP 64-bit
guest.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The in-kernel PIT emulation ignores pending timers if operating
under mode 3, which for example Hurd uses.
This mode should output a square wave, high for (N+1)/2 counts and low
for (N-1)/2 counts. As we only care about the resulting interrupts, the
period is N, and mode 3 is the same as mode 2 with regard to
interrupts.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To distinguish between real page faults and nested page faults they should be
traced as different events. This is implemented by this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds the missing kvmtrace markers to the svm
module of kvm.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds some kvmtrace bits to the generic x86 code
where it is instrumented from SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With an exit handler for INTR intercepts its possible to account them using
kvmtrace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With an exit handler for NMI intercepts its possible to account them using
kvmtrace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves the trace entry for APIC accesses from the VMX code to the
generic lapic code. This way APIC accesses from SVM will also be traced.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Noticed by sparse:
arch/x86/kvm/vmx.c:1583:6: warning: symbol 'vmx_disable_intercept_for_msr' was not declared. Should it be static?
arch/x86/kvm/x86.c:3406:5: warning: symbol 'kvm_task_switch_16' was not declared. Should it be static?
arch/x86/kvm/x86.c:3429:5: warning: symbol 'kvm_task_switch_32' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1968:6: warning: symbol 'kvm_mmu_remove_one_alloc_mmu_page' was not declared. Should it be static?
arch/x86/kvm/mmu.c:2014:6: warning: symbol 'mmu_destroy_caches' was not declared. Should it be static?
arch/x86/kvm/lapic.c:862:5: warning: symbol 'kvm_lapic_get_base' was not declared. Should it be static?
arch/x86/kvm/i8254.c:94:5: warning: symbol 'pit_get_gate' was not declared. Should it be static?
arch/x86/kvm/i8254.c:196:5: warning: symbol '__pit_timer_fn' was not declared. Should it be static?
arch/x86/kvm/i8254.c:561:6: warning: symbol '__inject_pit_timer_intr' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Switching msrs can occur either synchronously as a result of calls to
the msr management functions (usually in response to the guest touching
virtualized msrs), or asynchronously when preempting a kvm thread that has
guest state loaded. If we're unlucky enough to have the two at the same
time, host msrs are corrupted and the machine goes kaput on the next syscall.
Most easily triggered by Windows Server 2008, as it does a lot of msr
switching during bootup.
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM has a heuristic to unshadow guest pagetables when userspace accesses
them, on the assumption that most guests do not allow userspace to access
pagetables directly. Unfortunately, in addition to unshadowing the pagetables,
it also oopses.
This never triggers on ordinary guests since sane OSes will clear the
pagetables before assigning them to userspace, which will trigger the flood
heuristic, unshadowing the pagetables before the first userspace access. One
particular guest, though (Xenner) will run the kernel in userspace, triggering
the oops. Since the heuristic is incorrect in this case, we can simply
remove it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_mmu_pte_write() does not handle 32-bit non-PAE large page backed
guests properly. It will instantiate two 2MB sptes pointing to the same
physical 2MB page when a guest large pte update is trapped.
Instead of duplicating code to handle this, disallow directory level
updates to happen through kvm_mmu_pte_write(), so the two 2MB sptes
emulating one guest 4MB pte can be correctly created by the page fault
handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
rmap_next() does not work correctly after rmap_remove(), as it expects
the rmap chains not to change during iteration. Fix (for now) by restarting
iteration from the beginning.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If a timer fires after kvm_inject_pending_timer_irqs() but before
local_irq_disable() the code will enter guest mode and only inject such
timer interrupt the next time an unrelated event causes an exit.
It would be simpler if the timer->pending irq conversion could be done
with IRQ's disabled, so that the above problem cannot happen.
For now introduce a new vcpu requests bit to cancel guest entry.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A guest vcpu instance can be scheduled to a different physical CPU
between the test for KVM_REQ_MIGRATE_TIMER and local_irq_disable().
If that happens, the timer will only be migrated to the current pCPU on
the next exit, meaning that guest LAPIC timer event can be delayed until
a host interrupt is triggered.
Fix it by cancelling guest entry if any vcpu request is pending. This
has the side effect of nicely consolidating vcpu->requests checks.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Shadows for large guests can take a long time to tear down, so reschedule
occasionally to avoid softlockup warnings.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Clear CR4.VMXE in hardware_disable. There's no reason to leave it set
after doing a VMXOFF.
VMware Workstation 6.5 checks CR4.VMXE as a proxy for whether the CPU is
in VMX mode, so leaving VMXE set means we'll refuse to power on. With this
change the user can power on after unloading the kvm-intel module. I
tested on kvm-67 and kvm-69.
Signed-off-by: Eli Collins <ecollins@vmware.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Migrate the PIT timer to the physical CPU which vcpu0 is scheduled on,
similarly to what is done for the LAPIC timers, otherwise PIT interrupts
will be delayed until an unrelated event causes an exit.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The hypercall instructions on Intel and AMD are different. KVM allows the
guest to choose one or the other (the default is Intel), and if the guest
chooses incorrectly, KVM will patch it at runtime to select the correct
instruction. This allows live migration between Intel and AMD machines.
This patching occurs in the x86 emulator. The current code also executes
the hypercall. Unfortunately, the tail end of the x86 emulator code also
executes, overwriting the return value of the hypercall with the original
contents of rax (which happens to be the hypercall number).
Fix not by executing the hypercall in the emulator context; instead let the
guest reissue the patched instruction and execute the hypercall via the
normal path.
Signed-off-by: Avi Kivity <avi@qumranet.com>
