Restructure the UVC descriptors parsing code to handle multiple streaming
interfaces. The driver now creates a uvc_video_chain instance for each chain
detected in the UVC control interface descriptors, and tries to register one
video device per streaming endpoint.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards multiple streaming interfaces support, reorganize the
driver's data structures to cleanly separate video control and video streaming
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API (chapter 1.5) states that:
Drivers must implement all input ioctls when the device has one
or more inputs, all output ioctls when the device has one or more outputs.
When the device has any audio inputs or outputs the driver must set the
V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
VIDIOC_QUERYCAP ioctl.
So, devices without audio input should return -EINVAL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are many lock imbalances in this driver. Fix all found.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There seems to be one superfluos unlock in a poll function. Remove it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The irq handler will touch memory. Even in the error case some URBs may
complete. Thus no memory must be kfreed before all URBs are killed.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Zilog Z8F0811 IR transceiver chips on
CX2341[68] based boards to ir-kbd-i2c for both the old i2c binding model
and the new i2c binding model.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support to the cx18 driver for setting up the
Z8F0811/Hauppauge IR Tx/Rx chip with the i2c binding model in newer
kernels.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functions which are referenced by their address can't be inlined by
definition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au0828-dvb driver uses bulk usb transfers for digital transport,
but the debug reports, "iso xfer already running!\n".
Fix this to report bulk instead of isoc.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents a loop if a permanent error occurs in usb_set_interface().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patches
gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.
gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.
will make the preview function not work, so I disable the 1280x1024 resolution
and revert back to the origin mi1310_soc settings.
And, using USB snoop tool on Windows to get the correct i2c commands to
turn on/off the LED flash.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* use i2c_w instead of reg_w
* return error on failure
* read the correct number of bytes
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the i2c subdev changes the ordering of initialization changed,
causing a total loss of previous GPIO settings and a loss of DTV.
The generic firmware loading routine has now changed to preserve
GPIO values if the device is cx23885 based (safety) and I've
moved the GPIO configuration from probe() into the cx23885 init
func which is a little clearer and fixes the bug.
Tested-by: Sohail Syyed <linuxtv@hubstar.net>
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.
Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the subdev_s_std() method from the GPIO subdev. It appears it was
used in the past to effect the switch back from radio mode to tuner mode,
but it had a side effect that is improper and against the V4L2 spec, when
you were not in radio mode. Whenever the video stanadrd was changed, the
GPIO audio mux was set back to the tuner audio input, even if you were set
to a Line In input.
Thanks to Ravi A. for doing the troubleshooting to point me right to the
problem.
Reported-by: Ravi A <asvravi@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least one MT6227 model crashes when receiving a GET_DEF request on the
video probe control. As the various models can't be told apart based on the
descriptors, add a PROBE_DEF quirk to avoid sending the GET_DEF request and
enable the quirk for all models.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
. added code to print an error message when buffer is too small to hold frame
data, that is better than just a hard crash. Tested using MAX_FRAME_SIZE =
50000, lots of error messages appeared in /var/log/messages but no crash.
. removed line "f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;" in
zr364xx_vidioc_try_fmt_vid_cap, it should not be there.
. changes to improve performance (or at least not hurt it): removed some
unneeded debug messages; added macro FULL_DEBUG to enable debug messages in
performance critical places, this macro is disabled by default; removed "if
(frm->lpvbits == NULL)..." in zr364xx_read_video_callback because after
analisying the source code I concluded it will always results to false, so it
is not needed.
. some small code reorganization.
Signed-off-by: Lamarque V. Souza <lamarque@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements changing resolution in zr364xx_vidioc_s_fmt_vid_cap for
zr364xx driver. This version is synced with v4l-dvb as of 20/Jul/2009. Tested
with Creative PC-CAM 880.
OBS: I had to increase MAX_FRAME_SIZE to prevent a hard crash in my notebook
(caps lock blinking) when testing with mplayer, which automatically sets
resolution to the maximum (640x480). Maybe we should add code to auto-detect
frame size to prevent this kind of crash in the future.
Signed-off-by: Lamarque V. Souza <lamarque@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add CAM presence checkout during CiMax init for NetUP card.
CAM presence checkout is needed after power on PC.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx23885: Add support for ATSC/QAM on Hauppauge HVR-1850
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... improves readability and routes the calls through a specific single point.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The encoder driver has hardcoded GPIO bits set for the HVR1800, regardless
of whether it's being used by a HVR1800 or not. I've implemented some generic
GPIO manipulation routines and I'm calling them only when appropriate.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements V4L2_CAP_STREAMING for the zr364xx driver, by
converting the driver to use videobuf. This version is synced with v4l-dvb as
of 15/Jul/2009.
Tested with Creative PC-CAM 880.
It basically:
. implements V4L2_CAP_STREAMING using videobuf;
. re-implements V4L2_CAP_READWRITE using videobuf;
. copies cam->udev->product to the card field of the v4l2_capability struct.
That gives more information to the users about the webcam;
. moves the brightness setting code from before requesting a frame (in
read_frame) to the vidioc_s_ctrl ioctl. This way the brightness code is
executed only when the application requests a change in brightness and
not before every frame read;
. comments part of zr364xx_vidioc_try_fmt_vid_cap that says that Skype +
libv4l do not work.
This patch fixes zr364xx for applications such as mplayer,
Kopete+libv4l and Skype+libv4l can make use of the webcam that comes
with zr364xx chip.
Signed-off-by: Lamarque V. Souza <lamarque@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
[mchehab@redhat.com: fix the lack of linux/version.h]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, some devices with saa711x had their parameters controlled
directly inside em28xx driver, instead of using their proper module for
it.
Due to that, the ac97 controls were mixed with saa711x ones.
Older patches removed all saa711x controls, but we still need to control
ac97 devices on em28xx, since we don't have a separate v4l2 device for
it.
The proper way to address is to create a separate ac97 v4l2 device.
While we don't have it, we should clean up the code to allow having a
better view of what is part of em28xx core code and what's due to ac97
control inside it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As em28xx chip has nothing to do with volume/mute controls, rename those
controls to properly indicate that they control the companion AC97 chip
that it is inside the boards with this chip.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- call a new subdriver function 'isoc_init' before chosing the first
alternate setting.
- call a new subdriver function 'isoc_nego' when submitting the URBs failed.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only the back sensor (mi1320_soc) is usable.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
