Avoid unnecessarily pollution of the kernel's namespace by avoiding
mach/hardware.h. Include this header file where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move mci.h to new position in arch/arm/plat-s3c24xx/include/plat
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix fastpath issues
Since mmci_request() can be called from a non-interrupt
context, and does, during kernel init, causing a host
of debug messages during boot if you enable spinlock debugging,
we need to use the spinlock calls that save IRQ flags and
restore them.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
s3cmci: Add Ben Dooks/Simtec Electronics to header & copyright
s3cmci: fix continual accesses to host->pio_ptr
s3cmci: Support transfers which are not multiple of 32 bits.
s3cmci: cpufreq support
s3cmci: Make general protocol errors less noisy
mmc_block: tell block layer there is no seek penalty
Since the original authour (Thomas Kleffel) has been too busy to
merge the s3cmci driver and keep it up to date, I (mostly as part
of my role with Simtec Electronics) got the driver to a mergable
state and have been maintaining it since I think that I should
be added to the header. Also add a copyright statement for the
new work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The s3cmci driver uses the host->pio_ptr field to
point to the current position into the buffer for data
transfer. During the transfers it does the following:
while (fifo_words--)
*(host->pio_ptr++) = readl(from_ptr);
This is inefficent, as host->pio_ptr is not used in any
other part of the transfer but the compiler emits code
which does the following:
while (fifo_words--) {
u32 *ptr = host->pio_ptr;
*ptr = readl(from_ptr);
ptr++;
host->pio_ptr = ptr;
}
This is obviously a waste of a load and store each time
around the loop, which could be up to 16 times depending
on how much needs to be transfered.
Move the ptr accesses to outside the while loop so that
we do not end up reloading/re-writing the pointer.
Note, this seems to make the code 16 bytes larger.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
To be able to do SDIO the s3cmci driver has to support non-word-sized
transfers. Change pio_words into pio_bytes and fix up all the places
where it is used.
This variant of the patch will not overrun the buffer when reading an
odd number of bytes. When writing, this variant will still read past
the end of the buffer, but since the driver can't support non-word-
aligned transfers anyway, this should not be a problem, since a
word-aligned transfer will never cross a page boundary.
This has been tested with a CSR SDIO Bluetooth Type A device on a
Samsung S3C24A0 processor.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
General errors, such as timeouts during probe do not need to
be sent to the console, so move them down to be included if the
debug is enabled.
Such errors include:
s3c2440-sdi s3c2440-sdi: s3cmci_request: no medium present
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (24 commits)
MMC: Use timeout values from CSR
MMC: CSD and CID timeout values
sdhci: 'scratch' may be used uninitialized
mmc: explicitly mention SDIO support in Kconfig
mmc: remove redundant "depends on"
Fix comment in include/linux/mmc/host.h
sdio: high-speed support
mmc_block: hard code 512 byte block size
sdhci: force high speed capability on some controllers
mmc_block: filter out PC requests
mmc_block: indicate strict ordering
mmc_block: inform block layer about sector count restriction
sdio: give sdio irq thread a host specific name
sdio: make sleep on error interruptable
sdhci: reduce card detection delay
sdhci: let the controller wait for busy state to end
atmel-mci: Add missing flush_dcache_page() in PIO transfer code
atmel-mci: Don't overwrite error bits when NOTBUSY is set
atmel-mci: Add experimental DMA support
atmel-mci: support multiple mmc slots
...
Hard-coded timeout values of 250ms for writes and 100ms for reads are
currently used for MMC transactions over SPI. The spec states that the
timeout values from the card should be used.
Signed-off-by: Matthew Fleming <matthew.fleming@imgtec.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The variable 'scratch' is always initialized before it's used. The
conditional which is responsible for initialization of 'scratch' will
always evaluate 'true' when the first loop iteration occurs, and thus,
it's properly initialized. GCC doesn't see this, of course, so using
the uninitialized_var() macro seems to work for silencing this case.
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some high speed capable controllers forget to set the high speed
capability bit. Make sure we enable the functionality anyway.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The card detection delay was added early when the behaviour of the
card interrupt was still very much unknown (i.e. before there was a
public specification). As it is now known that it is a debounced signal,
reduce the delay to something more sensible.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The sdhci controllers can interrupt us when the busy state from the
card has ended, saving CPU cycles and power.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After a data error, we wait for the NOTBUSY bit to be set so that we can
be sure the data transfer is completely finished. However, when NOTBUSY
is set, the interrupt handler copies the contents of SR into
data_status, overwriting any error bits we may have detected earlier.
To avoid this, initialize data_status to 0 before starting a request, and
don't overwrite it unless it still contains 0.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Atmel MCI controller can drive multiple cards through separate sets
of pins, but only one at a time. This patch adds support for
multiplexing access to the controller so that multiple card slots can be
used as if they were hooked up to separate mmc controllers.
The atmel-mci driver registers each slot as a separate mmc_host. Both
access the same common controller state, but they also have some state
on their own for card detection/write protect handling, and separate
shadows of the MR and SDCR registers.
When one of the slots receives a request from the mmc core, the common
controller state is checked. If it's idle, the request is submitted
immediately. If not, the request is added to a queue. When a request is
done, the queue is checked and if there is a queued request, it is
submitted before the completion callback is called.
This patch also includes a few cleanups and fixes, including a locking
overhaul. I had to change the locking extensively in any case, so I
might as well try to get it right. The driver no longer takes any
irq-safe locks, which may or may not improve the overall system
performance.
This patch also adds a bit of documentation of the internal data
structures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.
Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.
Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Some cards might get upset if we turn off the clock for extended periods
of time. So keep the clock running until the mmc core tells us to turn
it off.
Also, don't reset the controller between each transfer. That was an
attempt to work around earlier bugs, and it never really worked very
well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
With the current system of completed/pending events, things may get
handled in different order depending on which event triggers first. For
example, if the data transfer is complete before the command, the stop
command must be sent after the command is complete, not the data. This
creates a bit of complexity around the stop command.
By having the tasklet go through a sequence of clearly defined states,
things always happen in a certain order even if the events come at
different times, so the stop command can simply be sent when we exit the
"sending data" state because we will never enter that state before the
command has been sent successfully.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
1. add a CPUID table in the comment
2. make cpu_is_pxa25x() true for PXA210/250/255/26x
3. PXA210 is treated as PXA25x, all related code modified to
reflect this
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows the mmc core to detect card insertion/removal for slots that
don't have any CD pin wired up.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We used to store a binary register snapshot in the "regs" file, so we
set the file size to be the size of this snapshot. This is no longer
valid since we switched to using seq_file.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The debugfs hook atmci_regs_show allocates a temporary buffer for
storing a register snapshot, but it doesn't free it before returning.
Plug this leak.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure that the peripheral clock is enabled before reading the MMIO
registers for the debugfs "regs" dump.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
At91_mci is abusing dma_free_coherent(), which may not be called with IRQs
disabled. I saw "mkfs.ext3" on an MMC card objecting voluminously as each
write completed:
WARNING: at arch/arm/mm/consistent.c:368 dma_free_coherent+0x2c/0x224()
[<c002726c>] (dump_stack+0x0/0x14) from [<c00387d4>] (warn_on_slowpath+0x4c/0x68)
[<c0038788>] (warn_on_slowpath+0x0/0x68) from [<c0028768>] (dma_free_coherent+0x2c/0x224)
r6:00008008 r5:ffc06000 r4:00000000
[<c002873c>] (dma_free_coherent+0x0/0x224) from [<c01918ac>] (at91_mci_irq+0x374/0x420)
[<c0191538>] (at91_mci_irq+0x0/0x420) from [<c0065d9c>] (handle_IRQ_event+0x2c/0x6c)
...
This bug has been around for a LONG time. The MM warning is from late
2005, but the driver merged a year later ... so I'm puzzled why nobody
noticed this before now.
The fix involves noting that this buffer shouldn't be DMA-coherent; it's
just used for normal DMA writes. So replace it with standard kmalloc()
buffering and DMA mapping calls.
This is the quickie fix. A better one would not rely on allocating large
bounce buffers. (Note that dma_alloc_coherent could have failed too, but
that case was ignored... kmalloc is a bit more likely to fail though.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/mmc/host/sdricoh_cs.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Attach the routine to get_cd to allow the MMC core to find out whether
there is a card present or not without the tedious process of trying to
send commands to the card or not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the following sparse errors by making the functions
static and fixing the check for host->base.
598:6: warning: symbol 's3cmci_dma_done_callback' was not declared. Should it be static?
744:6: warning: symbol 's3cmci_dma_setup' was not declared. Should it be static?
1209:20: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the MMC subdevice 'cell' commonly found in
TMIO based MFDs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Raise the DMA block size limit from 2048 bytes to the maximum supported
by the DMA controllers on the chip (64KB on Au1100, 4MB on Au1200).
This gives a very small performance boost and apparently fixes an oops
when MMC-DMA and network traffic are active at the same time.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The wrong flag was manipulated when an invalid sg list was given, turning
off DMA on the next (and all subsequent) request instead of the current
one.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Minor cleanups for the MMC/SD support on avr32:
- Make at32_add_device_mci() properly initialize "missing"
platform data ... so boards like STK1002 won't try GPIO 0.
- Switch over to gpio_is_valid() instead of testing for only
one designated value.
- Provide STK1002 platform data for the unlikely case that
switches are set so first Ethernet controller isn't in use.
(That's the only way to get card detect and writeprotect
switch sensing on the STK1000.)
And get rid of one "unused variable" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
atmel-mci: debugfs support
mmc: Add per-card debugfs support
mmc: Export internal host state through debugfs
imxmmc: fix crash when no platform data is provided
imxmmc: fix platform resources
imxmmc: remove DEBUG definition
mmc_spi: put signals to low power off fix
Don't crash if no platform data is provided.
In this case assume that card is present.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fixup platform resources handling.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Removed DEBUG #define #undef, because module is automaticaly
compiled with -DDEBUG when CONFIG_MMC_DEBUG is defined.
Currently it just generates compiler warning about redefinition.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha:
drivers/mmc/host/sdhci.h:242: error: field 'sg_miter' has incomplete type
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original intention was to write a zero byte to mmc to force spi
signals to low when doing power off. Somehow the spi_w8r8 call got there
so a read followed the write of single zero byte. This patch changes
that to simple write of zero byte without the following read.
This way the power off is more reliable and completely sufficient.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Commit c8b3e02 renamed a variable, but missed one reference to it
inside a WARN_ON, causing it to incorrectly trigger.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The ADMA code path assumes that the 3 byte alignment fix doesn't cross
a page boundary. I'm not convinced this is worth supporting, but at
least print a warning in the off chance we'll actually see such a request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ensure that the s3cmci host controller is turned off
when the machine is shutdown, otherwise we end up
leaving the card powered and processing insertion and
removal events after the system prints "System halted."
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Basic suspend/resume support: disable peripheral on suspend and
reinit on resume.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the naming of various functions in the s3cmc
driver to stop triggering section mismatch warnings.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch does a few small cleanups around the atmel mci platform code
and in the atmel-mci driver. The platform changes simply removes an
unused variable, uses the fact that by the end we always have some form
of platform data and notes that GPIO_PIN_NONE != 0. This last point
could cause the incorrect attempt to twice reserve pin PA0.
While we've got the hood up, add linux/err.h to the atmel-mci.c include
list. It needs it and generally pulls it by voodoo but I did once
stumble across a config which don't build.
This is against Linus' latest git.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This comment update got lost in the great floo^Wmerge. As Pierre
pointed out, no one knows what 'CaFe' is.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
DMA addresses are not pointers, so don't treat them as such. Avoids
compiler warnings when using 64-bit DMA addresses on a 32-bit system.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fix warning :shadowing dma variable
and made use of module_param_named instead of module_param
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The hardware does not support any multi-block transfers
with an block-size that is not 32bit aligned. Also the driver
itself does not support single block non-32bit transfers
either.
Ensure that the s3cmci_setup_data() returns the appropriate
error if we encounter this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add better debugging to show where errors are being
generated, as some error codes can come from several
different code paths.
Also fix the error return path from s3cmci_setup_data()
to return the error it returned to the request.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ensure that we have physical media present before attempting to
send a request to a card. This ensures that we do not get flooded
by errors from commands that can never be completed timing out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
mmc_detect_change() takes jiffies, not msecs. Convert the
previous value of msecs into jiffies before calling.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add MODULE_ALIAS() declerations for all the supported platform
devices for this driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The driver should be checking for a negative error code from
s3c2410_dma_request(), not non-zero. Newer kernels now return
the DMA channel number that was allocated by the request.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add support to the S3C24XX MMC driver to have the card detect be on
a pin that is not IRQ capable.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix a crash if host->mrq->data is NULL on ending a transfer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for inverting the sense of the MMC driver's write
protect detection line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds platform data support to the s3mci driver. This allows
flexible board-specific configuration of set_power, card detect and read only
pins.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix Bug #677 - I/O errors on heavy microSD writes for 2.6.22.x.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
is stopped.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Bugfix to ensure DMA channel allocated is freed on exit.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is the latest S3C MMC/SD driver by Thomas Kleffel
with cleanups as suggested by AKPM done by Ben Dooks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.
Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The upcoming JMicron chips will have solved all the currently known
bugs, so don't penalize them for older problems.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The MMC core provides a carddetect poll feature, time to
remove the driver's own implementation of it.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Don't process an MMC request if no card is present.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Clean up the codebase, no functional changes.
- merge the au1xmmc.h header contents into the driver file,
- indentation, spelling and style fixes.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Wire up the SD controllers' SDIO IRQ capability.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove the DB1200 board-specific functions (card present, read-only,
activity LED methods) and instead add platform data which is passed
to the driver. This also allows for platforms to implement other
carddetect schemes (e.g. dedicated irq) without having to pollute the
driver code. The poll timer (used for pb1200) is kept for compatibility.
With the board-specific stuff gone, the driver's ->probe() code can be
cleaned up considerably.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
According to the documentation the AT91SAM9261 MCI shares the block size
limitations of the AT91RM9200 MCI. Also the errata documentation for
AT91RM9200 and AT91SAM9261 state that stream commands are not supported.
This has not been tested on actual hardware.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs
but the actual condition for this erratum did not trigger in my tests so it's
unclear if it actually works as intended.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In at91_mci_completed_command() function, this patch distinguishes
command error and data error. It reports it in the corresponding
error field.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Reading AT91_MCI_SR again at the end of transfer can corrupt the
error reporting. Some fields in the SR register are read-and-clear.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Enable SDIO interrupt handling.
Signed-off-by: Eric Benard <ebenard@free.fr>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
at91_mci is capable of multiwrite. Enable it before it disappears.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Modify bytes_xfered value after a write.
That will report, as accurately as possible, the amount of
sectors that are effectively written.
This update introduces the check of the busy signal given by
the card.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The at91 mci controller internal state machine seems to often crash. This can
be fixed by resetting the controller after each command for at91rm9200 and by
setting the MCI_BLKR register on at91sam926*.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Implement transfer with size not modulo 4 for at91sam9*. Please note that the
at91rm9200 simply can't handle this.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.
This patch changes some hosts in two ways:
1. Now functions should be smart to not return negative values in
"RO asserted" case (particularly gpio_ calls could return negative
values for the outermost GPIOs).
Also, board code usually passes get_ro() callbacks that directly return
gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
handlers need take special care when returning platform's values to the
mmc core.
2. In case of host instance didn't implement get_ro() callback, it should
really return -ENOSYS and let the mmc core decide what to do about it
(mmc core thinks the same way as the hosts, so it isn't functional
change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds new platform data variable "caps", so platforms
could pass theirs capabilities into MMC core (for example, platforms
without interrupt on the CD line will most probably want to pass
MMC_CAP_NEEDS_POLL).
New platform get_cd() callback provided to optimize polling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Gracefully handle when the device is suddenly removed. Do a test read
and avoid any further access if that read returns -1.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
JMicron chips sometimes have two interfaces to work around limitations
in Microsoft's sdhci driver. This patch allows us to use either interface.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some of the JMicron chips requires us to manually enable the power
output stages of the chip. Add the necessary hooks and functions to
manage this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Give the quirk for broken timeout handling a better chance of handling
more controllers by simply classifying the system as broken and setting
a fixed value.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove the quirk to force DMA on the Ricoh and TI controllers as it is
no longer needed. The only bug they have is that they use an incorrect
PCI interface value, and that is not respected anymore.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.
This patch is based on work by Ben Dooks but he did not have time
to complete it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The specification is insufficiently strict when it comes to how the
hardware should update the block count register, making it useless
for checking transfer progress.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
The pxa27x DMA controller defaults to 64-bit alignment. This caused
the SCR reads to fail (and, depending on card type, error out) when
card->raw_scr was not aligned on a 8-byte boundary.
For performance reasons all scatter-gather addresses passed to
pxamci_request should be aligned on 8-byte boundaries, but if
this can't be guaranteed, byte aligned DMA transfers in the
have to be enabled in the controller to get correct behaviour.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even the newer ENE controllers have bugs in their DMA engine that make
it too dangerous to use. Disable it until someone has figured out under
which conditions it corrupts data.
This has caused problems at least once, and can be found as bug report
10925 in the kernel bugzilla.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CaFe chip has a hardware bug that ends up with us getting a timeout
value that's too small, causing the following sorts of problems:
[ 60.525138] mmcblk0: error -110 transferring data
[ 60.531477] end_request: I/O error, dev mmcblk0, sector 1484353
[ 60.533371] Buffer I/O error on device mmcblk0p2, logical block 181632
[ 60.533371] lost page write due to I/O error on mmcblk0p2
Presumably this is an off-by-one error in the hardware. Incrementing
the timeout count value that we stuff into the TIMEOUT_CONTROL register
gets us a value that works. This bug was originally discovered by
Pierre Ossman, I believe.
[thanks to Robert Millan for proving that this was still a problem]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been sitting around unloved for way too long..
The Marvell CaFe chip's SD implementation chokes during card insertion
if one attempts to set the voltage and power up in the same
SDHCI_POWER_CONTROL register write. This adds a quirk that does
that particular dance in two steps.
It also adds an entry to pci_ids.h for the CaFe chip's SD device.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.
Also converted all drivers using this function.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With CONFIG_DEBUG_SHIRQ set we will get an interrupt as soon as we
allocate one. Tasklets may be scheduled in the interrupt handler but they
will be initialized after the handler returns, causing a BUG() in
kernel/softirq.c when they run.
Should fix this Fedora bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=449817
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
at91_mci: minor cleanup
mmc: mmc host test driver
mmc: Fix omap compile by replacing dev_name with dma_dev_name
MMC_POWER_ON is a noop, no need to set the power pin again.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes error:
drivers/mmc/host/omap.c: In function 'mmc_omap_get_dma_channel':
drivers/mmc/host/omap.c:1038: error: called object 'dev_name' is not a function
Commit 06916639e2 adds a function
called dev_name. This will cause a name conflict as dev_dbg calls
dev_name(((host->mmc)->parent)).
This same issue should not affect other drivers as they don't seem
to use dev_name with dev_dbg.
Thanks to Paul Walmsley <paul@pwsan.com> for figuring this one out.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Otherwise it can only take the values 0/-1 which doesn't seem to
have been intended.
drivers/mmc/host/sdhci.h:190:20: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes some two minor clk issues.
The first is a comparison where a byte will probably wrap around to 0 instead of being saturated to 255, shouldn't be triggered very often but need fixing.
The second is an attempt by the driver to adjust MCLK down to the maximum frequency according to the spec, so we don't accidentally overclock the PL18x block. None of the mach-{versatile|integrator|lh7a40x} that use it in-tree seem to have a problem with this (all are well below 100MHz, typically 33MHz), but some day there will be a problem.
This is not applied on top of the earlier mmci patch for race condition but rather a clean 2.6.25, but I guess it applies without major protests anyway.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Jones <tonyj@suse.de>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updated version of 4446/1. This also drops the suggested comparison
of host_remain for == 0, since that doesn't make sense (still works
for us, too). We have verified that this patch solve race problems
on atleast 2 archs at high frequencies.
(Verbatim copy of old patch text below.)
The patch below fixes a race condition in the ARM MMCI PL18x driver.
If new data arrives in the FIFO while existing data is being read then
we get a second iteration of the loop in mmci_pio_read.
However host->size is not updated until after mmci_pio_read returns,
so we get count = number of new bytes PLUS number of bytes already
copied in the first iteration. This results in a FIFO underrun as
we try and read mode data than is available.
The fix is to compensating for data read on previous iterations
when calculating the amount of data in the FIFO.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
