Each break out of the for_each_available_child_of_node loop requires
of_node_put().
This patch adds missing of_node_put() when loop breaks on conflicting
values of led-sources DT property.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
The refcount of device_node increases after of_get_next_available_child()
is called. Make sure it is decremented also in case of DT parsing error.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Since brightness setting can sleep for this driver, implement
brightness_set_blocking op, instead of brightness_set.
It makes this driver compatible with LED triggers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Since brightness setting can sleep for this driver, implement
brightness_set_blocking op, instead of brightness_set.
It makes this driver compatible with LED triggers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
No need to explicitly check for pointer to be null,
of_prop_next_string anyways returns NULL, if passed pointer is NULL
and hence loop will continue.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The values of BCM6328_LED_MODE_ON and BCM6328_LED_MODE_OFF were named
for active low LEDs. These should be swapped so that they are named for
the default case of active high LEDs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When ensuring a consistent initial LED state in bcm6328_led (as they may
be blinking instead of on/off), the LED register is set using an inverted
copy of bcm6328_led_set(). To avoid further errors relating to active low
handling, call this function directly instead.
As bcm6328_led_set() acquires the same spinlock again when updating the
register, it is called after unlocking.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Workqueue, 'set_brightness_work' is used for scheduling brightness control.
This workqueue is canceled when the LED class device is unregistered.
Currently, LED subsystem handles like below.
cancel_work_sync(&led_cdev->set_brightness_work)
led_set_brightness(led_cdev, LED_OFF)
However, this could be a problem.
Workqueue is going to be canceled but LED device needs to be off.
The worst case is null pointer access due to scheduling a workqueue.
LED module is loaded.
LED driver private data is allocated by using devm_zalloc().
LED module is unloaded.
led_classdev_unregister() is called.
cancel_work_sync()
led_set_brightness(led_cdev, LED_OFF)
schedule_work() if LED driver uses brightness_set_blocking()
In the meantime, driver private data will be freed.
..scheduling..
brightness_set_blocking() callback is invoked.
For the brightness control, LED driver tries to access private
data but resource is removed!
To avoid this problem, LED subsystem should turn off the brightness first
and wait for completion.
led_set_brightness(led_cdev, LED_OFF)
flush_work(&led_cdev->set_brightness_work)
It guarantees that LED driver turns off the brightness prior to
resource management.
Cc: linux-leds@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Strobe state variable is declared as unsigned long, remove
the check for values less than zero then.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: David Binderman <dcb314@hotmail.com>
The refcount of device_node increases after of_node_get() is called.
So, a break out of the loop requires of_node_put().
This patch adds missing of_node_put() when loop breaks.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Some PWMs are disabled by default or the default pin setting
does not match the LED_OFF state (e.g., active-low leds).
Hence, the driver may end up reporting 0 brightness, but
the leds are actually on using full brightness, because
it never enforces its default configuration.
So enforce it by calling led_pwm_set() after successfully
registering the device.
Tested on a Phytec phyFLEX i.MX6Q board based on kernel
v3.19.5.
Signed-off-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Tested-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The header of this file fixes the license to GPL 2 only without the
option to use later version. So use the string "GPL v2" that is to be
used in this case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The transient trigger duration is documented to be in msec units, but is
actually in jiffies units. Other time based triggers are in msec units
as well. Fix the timer setup to convert from msec.
This could break an existing userspace that worked around this problem,
but exposing jiffies to userspace is just wrong and would break anyway
if HZ is changed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Raphael Assenat <raph@8d.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Raphael Assenat <raph@8d.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Reviewed-by: Mark Brown <broonie@kernel.org>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Milo Kim <milo.kim@ti.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Johan Hovold <johan@kernel.org>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Jan-Simon Moeller <dl9pf@gmx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the driver,
and switch to using brightness_set_blocking op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Now the core implements the work queue, remove it from the drivers,
and switch to using brightness_set_blocking op.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch removes SET_BRIGHTNESS_ASYNC and SET_BRIGHTNESS_SYNC flags.
led_set_brightness() now calls led_set_brightness_nosleep() instead of
choosing between sync and async op basing on the flags defined by the
driver.
From now on, if a user wants to make sure that brightness will be set
synchronously, they have to use led_set_brightness_sync() API. It is now
being made publicly available since it has become apparent that it is
a caller who should decide whether brightness is to be set in
a synchronous or an asynchronous way.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This patch makes LED core capable of setting brightness for drivers
that implement brightness_set_blocking op. It removes from LED class
drivers responsibility for using work queues on their own.
In order to achieve this set_brightness_delayed callback is being
modified to directly call one of available ops for brightness setting.
led_set_brightness_async() function didn't set brightness in an
asynchronous way in all cases. It was mistakenly assuming that all
LED subsystem drivers used work queue in their brightness_set op,
whereas only half of them did that. Since it has no users now,
it is being removed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This patch adds led_set_brightness_nosleep() and led_set_brightness_nopm()
functions, that guarantee setting LED brightness in a non-blocking way.
The latter is used from pm_ops context and doesn't modify the brightness
cached in the struct led_classdev. Its execution always ends up with
a call to brightness setting op - either directly or through
a set_brightness_work, regardless of LED_SUSPENDED flag state.
The patch also replaces led_set_brightness_async() with
led_set_brightness_nosleep() in all places where the most vital was setting
brightness in a non sleeping way but not necessarily asynchronously, which
is not needed for non-blocking drivers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The initial purpose of brightness_set_sync op, introduced along with
the LED flash class extension, was to add a means for setting torch LED
brightness as soon as possible, which couldn't have been guaranteed by
brightness_set op. This patch renames the op to brightness_set_blocking,
which describes its purpose in a more generic way. It is beneficial
in view of the prospective changes in the LED core, aiming at removing
the need for using work queues in LED class drivers that can sleep
or use delays while setting brightness.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This patch adds LED_BLINK_BRIGHTNESS_CHANGE flag to indicate that blink
brightness has changed, and LED_BLINK_DISABLE flag to indicate that
blinking deactivation has been requested. In order to use the flags
led_timer_function and set_brightness_delayed callbacks as well as
led_set_brightness() function are being modified. The main goal of these
modifications is to prepare set_brightness_work for extension of the
scope of its responsibilities.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
LED core has a mixture of EXPORT_SYMBOL and EXPORT_SYMBOL_GPL macros.
This patch fixes this discrepancy and switches to using EXPORT_SYMBOL_GPL
for each exported function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,r;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use of resource managed function devm_led_classdev_register to
make initialization path simpler. Also removed redundant remove
function.
Signed-off-by: Fida Mohammad <fmthoker@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use devm_led_classdev_register instead of led_classdev_register,
removing the redundant net48xx_led_remove function.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register, consequently remove redundant
menf21bmc_led_remove function.
Also drop the unneeded label err_free_leds.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource managed function devm_led_classdev_register to make
initialisation path simpler.
Also removed redundant led_classdev_unregister function.
Signed-off-by: Fida Mohammad <fmthoker@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
add a shutdown function for setting the gpio-leds
into off state when shuting down.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds more init register configuration options:
- Serial LEDs multiplexing.
- Serial LEDs clock signal low/high polarity.
- Serial LEDs data signal low/high polarity.
- Serial LEDs shift direction inverted/normal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch simplifies and improves the code related to
default-state handling.
It also changes the code to power off the LEDs by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Print invalid LED instead of warning only about maximum LED value.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch sets the led_classdev max_brightness to the maximum level
value supported by hardware. This allows to get rid of the brightness
conversion operation (from software [0:LED_FULL] to hardware ranges) in
brightness_set().
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch converts the leds-netxbig driver to use the devres functions
devm_gpio_request_one() and devm_led_classdev_register(). This allows to
simplify the code a bit.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds device tree support for the netxbig LEDs.
This also introduces a additionnal DT binding for the GPIO extension bus
(netxbig-gpio-ext) used to configure the LEDs. Since this bus could also
be used to control other devices, then it seems more suitable to have it
in a separate DT binding.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds possibility to invert heartbeat blinking.
The inverted LED is more time ON then OFF. It's because it looks
better when the heartbeat LED is next to other LED which is most
time ON. The invert value is exported same way via sysfs in file
invert like oneshot. I get inspiration from this trigger.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Since the API for controlling LED brightness and blinking is defined in
the LED core, move the related timer and work callbacks to the led-core.c,
and initialize them through a new led_core_init API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Spaces at the starting of a line are removed, indentation using
tab, instead of space. Also, line width of more than 80 characters
is also taken care of.
Two warnings are left alone to aid better readability.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use of resource-managed function devm_led_classdev_register
instead of led_classdev_register is preferred, consequently
remove redundant function micro_leds_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to make the error path simpler.
The goto is replaced with direct return, unneeded label err is
dropped. Also, remove redundant ot200_led_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register
instead of led_classdev_register to simplify error path.
An unnecessary check of ret is replaced with a direct return
Also, remove redundant hp6xxled_remove.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register to make the error-path simpler.
To be compatible with the change, goto is replaced with direct
return, unneeded label err_null is dropped and unnecessary variable
retval is removed. Also, remove redundant cobalt_qube_led_remove.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit [b67893206f: leds:lp55xx: fix firmware loading error]
tries to address the firmware file handling with user helper, but it
sets a wrong Kconfig CONFIG_FW_LOADER_USER_HELPER_FALLBACK. Since the
wrong option was enabled, the system got a regression -- it suffers
from the unexpected long delays for non-present firmware files.
This patch corrects the Kconfig dependency to the right one,
CONFIG_FW_LOADER_USER_HELPER. This doesn't change the fallback
behavior but only enables UMH when needed.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=944661
Fixes: b67893206f ('leds:lp55xx: fix firmware loading error')
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=URbg
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Stop using LP855X Platform Data to control regulators
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: tosa: Export I2C module alias information
backlight: lp8788_bl: Delete a check before backlight_device_unregister()
backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
backlight: pm8941-wled: Move PM8941 WLED driver to backlight
backlight: lp855x: Use private data for regulator control
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV5+GzAAoJEFHr6jzI4aWA0iAP/jcd0kNaNBzLgcDKKygKdgz4
xn4EWu81vfMfZYWesb0ATrjlH0hLsRxSXoFUqUMhtJTa5kNAoCIaz/M8WBALS50h
aT+i7br4WEU2j2FcaMyP3iAZx/2hl+2utODJSHPRWPkec1fUDBfEyBf++e520RWM
HUQGIGZXh8yq7KMA96Pwhsvls9vOB8hS2UdU/NS8ff3J5jFvXC1/WmF2qfzJBS1V
8iHyz26Jl8+dJ+et7iC2oD5XQAjIH1oJgOyPVPBzAQttfi8RjuVzRA30TfPBAUwI
lC9nlmPy6bCe4kiQYWVB1z7GegHyW/9vkeuMj/u8mZbqpaayMEMZmd2C3iNDXNHx
i2NSvdln539t4qWYsV2v6lVCfa/ayDHD73Wackj5Dk394tzXnpCPhxNzc2yKEd5v
h7vwYc9jBhsbfSCSogaM+gSHJ1APgCidggHJMYYNA2nN2u6V62RpsMB7zp/1+Q2v
yqYdD8oYF4Dm21x/ujaNFrlizROD46WS0UqdJ3yP6HAqRYIpRXtibmpECJgt1n5h
HjADEci4hQ2UQxdMdp/Q5KZnPTJebBtrZrmkW5r6cZBUaTB5TVkFaEWN44CT/Loh
tMNeA3qOBN06CaQS2WL3UUUWpbZq9fSbWuUZ5lWZDb5AOyRxe5eWVYNLkiyIXozY
L24l1bYdBhXahnjoS/kc
=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
- optimizations and improvements to existing LED class drivers
- improvements to the common LEDs DT documentation
- modifications of kirkwood-* dts files, to be in sync with patches for
leds-ns2 driver, that move LEDs mode mapping outside of the driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)
iQIcBAABAgAGBQJV5EAlAAoJEL1qUBy3i3wmcZkP/3ZdQZsv5EbF5XLZFXPORs2s
BQESLaTVdbgDuSP6CoNkpOGucc5115z+/8GmskWreSck8qxUzgwR8sClU9T2eNi4
epA3SUBi2QaqjK8sl7tRbva0kAXNT+KqHgPwCuN0Pui0EgXsPHEnDYKfLWULx+wi
6NVofK2pTHTV+V3QccjMvO4443Mi9FNO9Ee0EaSVPdE/Mh2rIUPhtB5KmK/XUEv1
gBqVysRoTw/sE5z6SDX2FaSs+98L6UNP9tC8qZCLFqwe2SdQZNqwYJklzHlm3ErI
lrkxJaJ7NixB4zAO5MKJ7eZJmJ+YMroC2uIa4DjKiiekfA1d18ioOB6jFgkFyH0o
cErLiXKbJoabIc1XsoE/XT7v8a+dSVB9Tj3OPWQcx6HlGpBXTRcV5sayh0wX895Z
mn0taprYqS+MnPY/M8jrsl6btsUVRfV6jyneExhIxc3gArkjEjb9m/h3mQNauB8h
I0kZ56q1nYCcp/4JhfrUEwnD0sdX9jUqvr3yIOFgNknOHAsqgXMgW38H0RxsBiI4
Tx33cXkp6zh0wqVTPmWe2Ic1xAVY/dSd3ZF2smjzhbwe37unPrXNym6eRguu0ezb
4ZFjvetkqmz8uqyyTq3Lfc5rfbGPOgtCLvKXOgEyo2HaNPPAxeHqRI3HU8bBDtqp
j0CCXXXhVqRg4VTzJiXk
=sa6j
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this merge window we'd like to announce a change on the list of LED
subsystem maintainers - Bryan Wu decided to step back and handed over
the maintainership to me (Jacek Anaszewski), which entailed an update
of LED subsystem git tree URL.
Besides the changes in MAINTAINERS we have:
- optimizations and improvements to existing LED class drivers
- improvements to the common LEDs DT documentation
- modifications of kirkwood-* dts files, to be in sync with patches
for leds-ns2 driver, that move LEDs mode mapping outside of the
driver"
* tag 'leds_for_4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: Export OF module alias information in missing drivers
leds:lp55xx: use the private data instead of updating I2C device platform data
leds: syscon: Correct check for syscon_node_to_regmap() errors
leds: leds-fsg: Use devm_led_classdev_register
MAINTAINERS: Change LED subsystem git tree URL
leds/led-class: Add missing put_device()
ARM: Kirkwood: add modes-map property to ns2-leds nodes
leds: tlc591xx: Remove redundant I2C_FUNC_SMBUS_BYTE_DATA functionality check
leds: leds-ns2: depends on MACH_ARMADA_370
leds: leds-ns2: handle can_sleep GPIOs
leds: leds-ns2: move LED modes mapping outside of the driver
leds: lp8860: Constify reg_default tables
leds: Drop owner assignment from i2c_driver
leds: Allow compile test of LEDS_AAT1290 and LEDS_KTD2692 if !GPIOLIB
leds: Allow compile test of GPIO consumers if !GPIOLIB
DT: leds: Improve description of flash LEDs related properties
The I2C core always reports the MODALIAS uevent as "i2c:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: I2C id table or OF match table).
So drivers needs to export the I2C id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and I2C id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same I2C device name for example.
To avoid the above, the I2C core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Currently, lp55xx_of_populate_pdata() allocates lp55xx_platform_data if
it's null. And it parses the DT and copies values into the
'client->dev.platform_data'. This may have architectural issue.
Platform data is configurable through the DT or I2C board info inside the
platform area. However, lp55xx common driver changes this configuration
when it is loaded. So 'client->dev.platform_data' is not null anymore.
Eventually, the driver initialization is not identical when it's unloaded
and loaded again.
The lp55xx common driver should use the private data, 'lp55xx_chip->pdata'
instead of changing the original platform data.
So, lp55xx_of_populate_pdata() is modified as follows.
* Do not update 'dev->platform_data'. Return the pointer of new allocated
lp55xx_platform_data. Then the driver points it to private data,
'lp55xx_chip->pdata'.
* Each lp55xx driver checks the pointer and handles an error case.
Then, original platform data configuration will be kept regardless of
loading or unloading the driver.
The driver allocates the memory and copies them from the DT if it's NULL.
After the driver is loaded again, 'client->dev.platform_data' is same as
initial load, so the driver is initialized identically.
Cc: Toshi Kikuchi <toshik@chromium.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
syscon_node_to_regmap() returns a regmap or an ERR_PTR().
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register to make the error-path simpler.
To be compatible with the change, various gotos are replaced with
direct returns and unneeded labels are dropped. Also, remove
fsg_led_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Devices found by class_find_device must be freed with put_device().
Otherwise the reference count will not work properly.
Fixes: a96aa64cb5 ("leds/led-class: Handle LEDs with the same name")
Reported-by: Alan Tull <delicious.quinoa@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This checking is done by regmap_get_i2c_bus() which is called in
devm_regmap_init_i2c().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The leds-ns2 driver is also used by the n090401 board (Seagate NAS
4-Bay), which is based on the Marvell Armada-370 SoC.
Then this patch allows to select the leds-ns2 driver if MACH_ARMADA_370
is enabled. Additionally, this also updates the Kconfig help message.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
On the board n090401 (Seagate NAS 4-Bay), some of the LEDs are handled
by the leds-ns2 driver. This LEDs are connected to an I2C GPIO expander
(PCA95554PW) which means that GPIO access may sleep. This patch makes
leds-ns2 compatible with such GPIOs by using the *_cansleep() variant of
the GPIO functions. As a drawback this functions can't be used safely in
a timer context (with the timer LED trigger for example). To fix this
issue, a workqueue mechanism (copied from the leds-gpio driver) is used.
Note that this patch also updates slightly the ns2_led_sata_store
function. The LED state is now retrieved from cached values instead of
reading the GPIOs previously. This prevents ns2_led_sata_store from
working with a stale LED state (which may happen when a delayed work
is pending).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
On the board n090401 (Seagate NAS 4-Bay), the LED mode mapping (GPIO
values to LED mode) is different from the one used on other boards
supported by the leds-ns2 driver.
With this patch the hardcoded mapping is removed from leds-ns2. Now,
it must be defined either in the platform data (if an old-fashion board
setup file is used) or in the DT node. In order to allow the later, this
patch also introduces a modes-map property for the leds-ns2 DT binding.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
If COMPILE_TEST is enabled, relax the dependency on GPIOLIB for the
recently introduced symbols LEDS_AAT1290 and LEDS_KTD2692.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Qualcomm PM8941 WLED block is used for backlight and should therefor
be in the backlight framework and not in the LED framework. This moves
the driver and adapts to the backlight api instead.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When I merged the OPAL support for the powernv LEDS driver I missed a
hunk.
This is slightly modified from the original patch, as the original added
code to opal-api.h which is not in the skiboot version, which is
discouraged.
Instead those values are moved into the driver, which is the only place
they are used.
Fixes: 8a8d91817a ("powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states")
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements LED driver for PowerNV platform using the existing
generic LED class framework.
PowerNV platform has below type of LEDs:
- System attention
Indicates there is a problem with the system that needs attention.
- Identify
Helps the user locate/identify a particular FRU or resource in the
system.
- Fault
Indicates there is a problem with the FRU or resource at the
location with which the indicator is associated.
We register classdev structures for all individual LEDs detected on the
system through LED specific device tree nodes. Device tree nodes specify
what all kind of LEDs present on the same location code. It registers
LED classdev structure for each of them.
All the system LEDs can be found in the same regular path /sys/class/leds/.
We don't use LED colors. We use LED node and led-types property to form
LED classdev. Our LEDs have names in this format.
<location_code>:<attention|identify|fault>
Any positive brightness value would turn on the LED and a zero value would
turn off the LED. The driver will return LED_FULL (255) for any turned on
LED and LED_OFF (0) for any turned off LED.
The platform level implementation of LED get and set state has been
achieved through OPAL calls. These calls are made available for the
driver by exporting from architecture specific codes.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull LED subsystem updates from Bryan Wu:
"In this cycle, we finished to merge patches for LED Flash class
driver.
Other than that we have some bug fixes and new drivers for LED
controllers"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (33 commits)
leds:lp55xx: fix firmware loading error
leds: fix max77693-led build errors
leds: fix aat1290 build errors
leds: aat1290: pass flags parameter to devm_gpiod_get
leds: ktd2692: pass flags parameter to devm_gpiod_get
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
leds: aat1290: add support for V4L2 Flash sub-device
DT: aat1290: Document handling external strobe sources
leds: max77693: add support for V4L2 Flash sub-device
media: Add registration helpers for V4L2 flash sub-devices
v4l: async: Add a pointer to of_node to struct v4l2_subdev, match it
Documentation: leds: Add description of v4l2-flash sub-device
leds: add BCM6358 LED driver
leds: add DT binding for BCM6358 LED controller
leds: fix brightness changing when software blinking is active
Documentation: leds-lp5523: describe master fader attributes
leds: lp5523: add master_fader support
leds: leds-gpio: Allow compile test if !GPIOLIB
leds: leds-gpio: Add missing #include <linux/of.h>
gpiolib: Add missing dummies for the unified device properties interface
...
- Fix a recently added memory leak in an error path in the ACPI
resources management code (Dan Carpenter).
- Fix a build warning triggered by an ACPI video header function
that should be static inline (Borislav Petkov).
- Change names of helper function converting struct fwnode_handle
pointers to either struct device_node or struct acpi_device
pointers so they don't conflict with local variable names
(Alexander Sverdlin).
- Make the hibernate core re-enable nonboot CPUs on failures to
disable them as expected (Vitaly Kuznetsov).
- Increase the default timeout of the device suspend watchdog to
prevent it from triggering too early on some systems (Takashi Iwai).
- Prevent the cpuidle powernv driver from registering idle
states with CPUIDLE_FLAG_TIMER_STOP set if CONFIG_TICK_ONESHOT
is unset which leads to boot hangs (Preeti U Murthy).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=vkde
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes that didn't make it to the previous PM+ACPI pull
request or are fixing issues introduced by it.
Specifics:
- Fix a recently added memory leak in an error path in the ACPI
resources management code (Dan Carpenter)
- Fix a build warning triggered by an ACPI video header function that
should be static inline (Borislav Petkov)
- Change names of helper function converting struct fwnode_handle
pointers to either struct device_node or struct acpi_device
pointers so they don't conflict with local variable names
(Alexander Sverdlin)
- Make the hibernate core re-enable nonboot CPUs on failures to
disable them as expected (Vitaly Kuznetsov)
- Increase the default timeout of the device suspend watchdog to
prevent it from triggering too early on some systems (Takashi Iwai)
- Prevent the cpuidle powernv driver from registering idle states
with CPUIDLE_FLAG_TIMER_STOP set if CONFIG_TICK_ONESHOT is unset
which leads to boot hangs (Preeti U Murthy)"
* tag 'pm+acpi-4.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
ACPI / video: Inline acpi_video_set_dmi_backlight_type
ACPI / resources: free memory on error in add_region_before()
LP55xx driver uses not firmware file but raw data to load program through
the firmware interface.(Documents/leds/leds-lp55xx.txt)
For example, here is how to run blinking green channel pattern.
(The second engine is seleted and MUX is mapped to 'RGB' mode)
echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux
echo 1 > /sys/class/firmware/lp5562/loading
echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
echo 0 > /sys/class/firmware/lp5562/loading
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
However, '/sys/class/firmware/<device name>' is not created after the
firmware loader user helper was introduced.
This feature is used in the case below.
As soon as the firmware download is requested by the driver, firmware
class subsystem tries to find the binary file.
If it gets failed, then it just falls back to user helper to load
raw data manually. Here, you can see the device file under
/sys/class/firmware/.
To make it happen, LP55xx driver requires two configurations.
1. Enable CONFIG_FW_LOADER_USER_HELPER_FALLBACK in Kconfig
2. Set option, 'FW_OPT_USERHELPER' on requesting the firmware data.
It means the second option should be 'false' in
request_firmware_nowait().
This option enables to load firmware data manually by calling
fw_load_from_user_helper().
Cc: linux-leds@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fix build errors when LEDS_MAX77693=y and V4L2_FLASH_LED_CLASS=m
by restricting LEDS_MAX77693 to =m if V4L2_FLASH_LED_CLASS=m.
drivers/leds/leds-max77693.c:1062: undefined reference to `v4l2_flash_release'
drivers/leds/leds-max77693.c:1068: undefined reference to `v4l2_flash_release'
drivers/built-in.o: In function `max77693_register_led':
drivers/leds/leds-max77693.c:968: undefined reference to `v4l2_flash_init'
drivers/built-in.o: In function `max77693_led_probe':
drivers/leds/leds-max77693.c:1048: undefined reference to `v4l2_flash_release'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fix build errors when LEDS_AAT1290=y and V4L2_FLASH_LED_CLASS=m
by restricting LEDS_AAT1290 to =m if V4L2_FLASH_LED_CLASS=m.
drivers/built-in.o: In function `aat1290_led_remove':
leds-aat1290.c:(.text+0xe5d77): undefined reference to `v4l2_flash_release'
drivers/built-in.o: In function `aat1290_led_probe':
leds-aat1290.c:(.text+0xe6494): undefined reference to `v4l2_flash_init'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=02Gm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
* acpi-video:
ACPI / video: Inline acpi_video_set_dmi_backlight_type
* device-properties:
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
* pm-sleep:
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
* pm-cpuidle:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
Commit 8a0662d9 introduced of_node and acpi_node symbols in global namespace
but there were already ~63 of_node local variables or function parameters
(no single acpi_node though, but anyway).
After debugging undefined but used of_node local varible (which turned out
to reference static function of_node() instead) it became clear that the names
for the functions are too short and too generic for global scope.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
In this case the driver cannot easily be simplified but as the flags
parameter will become mandatory soon this change is necessary
beforehand.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
In this case the driver cannot easily be simplified but as the flags
parameter will become mandatory soon this change is necessary
beforehand.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This file is built for a bool Kconfig variable, and hence this
code is either present or absent. It currently can never be
modular, so using module_init as an alias for __initcall can be
somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
And since it can't be modular, we remove all the __exitcall
stuff related to module_exit() -- it is dead code that won't
ever be executed.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add support for V4L2 Flash sub-device to the aat1290 LED Flash class
driver. The support allows for V4L2 Flash sub-device to take the control
of the LED Flash class device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add support for V4L2 Flash sub-device to the max77693 LED Flash class
driver. The support allows for V4L2 Flash sub-device to take the control
of the LED Flash class device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the LED controller on Broadcom's BCM6358.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The following sequence:
echo timer >/sys/class/leds/<name>/trigger
echo 1 >/sys/class/leds/<name>/brightness
should change the ON brightness for blinking.
The function led_set_brightness() was mistakenly initiating the
delayed blink stop procedure, which resulted in no blinking with
the timer trigger still active.
This patch fixes the problem by changing led_set_brightness()
to not initiate the delayed blink stop when brightness is not 0.
CC: Richard Purdie <rpurdie@rpsys.net>
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: linux-leds@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch introduces 4 new attributes:
master_fader_leds
master_fader1
master_fader2
master_fader3
Fo example, to map channel 0,6 to master_fader1,
map channel 1,7 to master_fader2,
map channel 2,8 to master_fader3, and
map channel 3,4,5 to none
echo "123000123" > master_fader_leds
A different factor can be set to each master_fader:
echo 255 > master_fader1
echo 100 > master_fader2
echo 0 > master_fader3
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-by: Milo Kim <milo.kim@ti.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of LEDS_GPIO on GPIOLIB if COMPILE_TEST is
enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds a driver to support the ktd2692 flash LEDs.
ktd2692 can control flash current by ExpressWire interface.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of
hibernation callbacks means those pm functions will not be
called upon hibernation - that leads to system crash on ARM during
freezing if gpio-led is used in combination with CPU led trigger.
It may happen after freeze_noirq stage (GPIO is suspended)
and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.
Log:
PM: noirq freeze of devices complete after 1.425 msecs
Disabling non-boot CPUs ...
^ system may crash or stuck here with message (TI AM572x)
WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access
CPU1: shutdown
^ or here
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation callbacks and move
led_suspend/led_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Fixes: 73e1ab41a8 (leds: Convert led class driver from legacy pm ops to dev_pm_ops)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently syscon LEDs will traverse the device tree looking for syscon devices
and if found, traverse any subnodes of these to identify matching children
and from there instantiate LED class devices.
This is not a good use of the Linux device model. Instead we have converted the
device trees to add the "simple-mfd" property to the MFD nexi spawning syscon
LEDs so that these will appear as platform devices in the system and we can
use the proper device probing mechanism.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the LED controller on Broadcom's BCM6328.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds a driver for the 1.5A Step-Up Current Regulator
for Flash LEDs. The device is programmed through a Skyworks proprietary
AS2Cwire serial digital interface.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds led-flash support to Maxim max77693 chipset.
A device can be exposed to user space through LED subsystem
sysfs interface. Device supports up to two leds which can
work in flash and torch mode. The leds can be triggered
externally or by software.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Part of led-trigger API was in the private drivers/leds/leds.h header.
Move it to the include/linux/leds.h header to unify the API location
and announce it as public. It has been already exported from
led-triggers.c with EXPORT_SYMBOL_GPL macro. The no-op definitions are
changed from macros to inline to match the style of the surrounding code.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Make sure that already registered LEDs will be torn down properly
if the name of the next LED to create is unavailable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In gpio_leds_create(), when devm_get_gpiod_from_child() fails with
-EPROBE_DEFER on the second gpio led to be created, the first already
registered led is not torn down properly. This causes create_gpio_led()
to fail for the first led on re-probe().
Fix this misbehaviour by incrementing num_leds only if all
potentially failing calls completed successfully.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The TLC59116 is an I2C bus controlled 16-channel LED driver. The
TLC59108 is an I2C bus controlled 8-channel LED driver, which is very
similar to the TLC59116. Each LED output has its own 8-bit
fixed-frequency PWM controller to control the brightness of the LED.
The LEDs can also be fixed off and on, making them suitable for use as
GPOs.
This is based on a driver from Belkin, but has been extensively
rewritten and extended to support both 08 and 16 versions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Matthew.Fatheree@belkin.com
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
The LED name was wrongly interpreted as format string. Stop doing that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
The LED names are expected to be unique in the system. Use KERN_WARNING log
level to notify the user about the matter.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
The current code expected that every LED had an unique name. This is a
legit expectation when the device tree can no be modified or extended.
But with device tree overlays this requirement can be easily broken.
This patch finds out if the name is already in use and adds the suffix
_1, _2... if not.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch fix a spelling typo in MODULE_DESCRIPTION in
leds-lp8860.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch fix a spelling typo in MODULE_DESCRIPTION in
leds-lp8501.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds support for the WLED ('White' LED) block on Qualcomm's
PM8941 PMICs.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Only the name and default_trigger fields are initialized.
Other fields (currently flags only) contain random stack data.
Pre-initialize the led structure completely to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Synchronized flash strobe feature has been considered not fitting
for LED subsystem sysfs interface and thus is being removed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
(cooloney@gmail.com: add _unregister function into the document)
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The gpio binding document says that new code should always use named
gpios. Patch 40b73183 added support to parse a list of gpios from child
nodes, but does not make it possible to use named gpios. This patch adds
the con_id property and implements it is done in gpiolib.c, where the
old-style of using unnamed gpios still works.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probe function open coded a bad variant of devm_gpiod_get_optional
using devm_gpiod_get and just ignoring all errors.
In contrast to that devm_gpiod_get_optional returns NULL if there was no
corresponding gpio specified in the device tree (or ACPI table) and
fails if there is an error (or GPIOLIB is not enabled).
Moreover since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) which appeared in v3.17-rc1, the gpiod_get* functions take an
additional parameter that allows to specify direction and initial value
for output which allows some simplification.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
pwm_get_period() is called twice in case the child parameter is set. I
assume retrieving this parameter once is enough therefore this patch
removes the conditial invocation of pwm_get_period().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Instead of overriding error codes, pass them on unmodified. This
way a EPROBE_DEFER is correctly passed to the driver core. This results
in the LED driver correctly requesting probe deferral in cases the GPIO
controller is not yet available.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-and-tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some LED devices support two operation modes - torch and flash.
This patch provides support for flash LED devices in the LED subsystem
by introducing new sysfs attributes and kernel internal interface.
The attributes being introduced are: flash_brightness, flash_strobe,
flash_timeout, max_flash_timeout, max_flash_brightness, flash_fault,
flash_sync_strobe and available_sync_leds. All the flash related
features are placed in a separate module.
The modifications aim to be compatible with V4L2 framework requirements
related to the flash devices management. The design assumes that V4L2
sub-device can take of the LED class device control and communicate
with it through the kernel internal interface. When V4L2 Flash sub-device
file is opened, the LED class device sysfs interface is made
unavailable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
of_find_node_by_name() calls of_node_put() on its "from" parameter.
To counter this, mc13xxx_led_probe_dt() calls of_node_get() first.
Use of_get_child_by_name() instead to get rid of the refcount hack.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Since commit 4d71a4a12b ("leds: Add support for setting brightness in
a synchronous way") the value passed to brightness_set() is no longer
limited to max_brightness and can be different from the internally saved
brightness value.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch fixes a NULL pointer dereference on led_dat->mode_val. Due to
this bug, a kernel oops can be observed at probe time on the LaCie 2Big
and 5Big v2 boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
[...]
[<c03f244c>] (netxbig_led_probe) from [<c02c8c6c>] (platform_drv_probe+0x4c/0x9c)
[<c02c8c6c>] (platform_drv_probe) from [<c02c72d0>] (driver_probe_device+0x98/0x25c)
[<c02c72d0>] (driver_probe_device) from [<c02c7520>] (__driver_attach+0x8c/0x90)
[<c02c7520>] (__driver_attach) from [<c02c5c24>] (bus_for_each_dev+0x68/0x94)
[<c02c5c24>] (bus_for_each_dev) from [<c02c6408>] (bus_add_driver+0x124/0x1dc)
[<c02c6408>] (bus_add_driver) from [<c02c7ac0>] (driver_register+0x78/0xf8)
[<c02c7ac0>] (driver_register) from [<c000888c>] (do_one_initcall+0x80/0x1cc)
[<c000888c>] (do_one_initcall) from [<c0733618>] (kernel_init_freeable+0xe4/0x1b4)
[<c0733618>] (kernel_init_freeable) from [<c058db9c>] (kernel_init+0xc/0xec)
[<c058db9c>] (kernel_init) from [<c0009850>] (ret_from_fork+0x14/0x24)
[...]
This bug was introduced by commit 588a6a9928
("leds: netxbig: fix attribute-creation race").
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # 3.17+
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Pull LED subsystem update from Bryan Wu:
"We got some cleanup and driver for LP8860 as well as some patches for
LED Flash Class"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: lp8860: Fix module dependency
leds: lp8860: Introduce TI lp8860 4 channel LED driver
leds: Add support for setting brightness in a synchronous way
leds: implement sysfs interface locking mechanism
leds: syscon: handle multiple syscon instances
leds: delete copy/paste mistake
leds: regulator: Convert to devm_regulator_get_exclusive
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Commit a43f2cbbb0 ("leds: leds-gpio: Make use of device property API")
caused a regression by reading the incorrect string for the "default-state"
property.
Fix the property string check to restore the original behaviour.
Fixes: a43f2cbbb0 (leds: leds-gpio: Make use of device property API)
Reported-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit a43f2cbbb0 ("leds: leds-gpio: Make use of device property
API") it is no longer possible to register multiple gpio leds without passing
the 'label' property.
According to Documentation/devicetree/bindings/leds/common.txt:
"Optional properties for child nodes:
- label : The label for this LED. If omitted, the label is
taken from the node name (excluding the unit address)."
So retrieve the node name when the 'label' property is absent to keep the old
behaviour and fix this regression.
Fixes: a43f2cbbb0 (leds: leds-gpio: Make use of device property API)
Reported-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The driver should select REGMAP_I2C rather than depend on it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Introduce the Texas Instruments lp8860
4 channel LED driver.
This driver configures the device in display cluster mode
as this seems to be the most used configuration at the
time of the driver configuration.
For more product information please see the link below:
http://www.ti.com/product/lp8860-q1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
There are use cases when setting a LED brightness has to
have immediate effect (e.g. setting a torch LED brightness).
This patch extends LED subsystem to support such operations.
The LED subsystem internal API __led_set_brightness is changed
to led_set_brightness_async and new led_set_brightness_sync API
is added.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add a mechanism for locking LED subsystem sysfs interface.
This patch prepares ground for addition of LED Flash Class
extension, whose API will be integrated with V4L2 Flash API.
Such a fusion enforces introducing a locking scheme, which
will secure consistent access to the LED Flash Class device.
The mechanism being introduced allows for disabling LED
subsystem sysfs interface by calling led_sysfs_disable function
and enabling it by calling led_sysfs_enable. The functions
alter the LED_SYSFS_DISABLE flag state and must be called
under mutex lock. The state of the lock is checked with use
of led_sysfs_is_disabled function. Such a design allows for
providing immediate feedback to the user space on whether
the LED Flash Class device is available or is under V4L2 Flash
sub-device control.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Currently the syscon LED driver will only handle LEDs on the
first syscon found in the system. But there can be several of
them, so augment the driver to traverse all syscon nodes and
check for syscon LEDs on them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
A chunk of text followed the copied license text, ehm, sorry
that kind of things happen from time to time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In the legacy case, led_dat->gpiod is initialized correctly, but
overwritten later by template->gpiod, which is NULL, causing leds-gpio
to fail with:
gpiod_direction_output: invalid GPIO
leds-gpio: probe of leds-gpio failed with error -22
Move the initialization of led_dat->gpiod from template->gpiod up, and
always use led_dat->gpiod later, to fix this.
Fixes: 5c51277a9a (leds: leds-gpio: Add support for GPIO descriptors)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 21f2aae91e902aad ("leds: leds-gpio: Add support for GPIO
descriptors") already converted most of the driver to use GPIO descriptors.
What is still missing is the platform specific hook gpio_blink_set() and
board files which pass legacy GPIO numbers to this driver in platform data.
In this patch we handle the former and convert gpio_blink_set() to take
GPIO descriptor instead. In order to do this we convert the existing four
users to accept GPIO descriptor and translate it to legacy GPIO number in
the platform code. This effectively "pushes" legacy GPIO number usage from
the driver to platforms.
Also add comment to the remaining block describing that it is legacy code
path and we are getting rid of it eventually.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make use of device property API in this driver so that both OF and ACPI
based system can use the same driver.
This change contains material from Max Eliaser and Mika Westerberg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull LED update from Bryan Wu:
"Basically we have some bug fixing and clean up and one big thing is we
start to merge patch to add support LED Flash class"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: gpio: cleanup the leds-gpio driver
led: gpio: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
led: gpio: Sort include headers alphabetically
leds: Improve and export led_update_brightness
leds: trigger: gpio: fix warning in gpio trigger for gpios whose accessor function may sleep
leds: lp3944: fix sparse warning
leds: avoid using DEVICE_ATTR macro for max_brightness attribute
leds: make brightness type consistent across whole subsystem
leds: Reorder include directives
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into drivers
directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=POJD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others,
as well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Smzi
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others, as
well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: update Shawn's email address
MAINTAINERS: condense some Tegra related entries
MAINTAINERS: add Alexandre Courbot for Tegra
MAINTAINERS: CNS3xxx and IXP4xx update.
MAINTAINERS: Add maintainers entry for Mediatek SoCs
arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500
MAINTAINERS: add a third maintainer to mach-bcm
CNS3xxx: Fix PCIe read size limit.
CNS3xxx: Fix logical PCIe topology.
CNS3xxx: Fix debug UART.
MAINTAINERS: Add entry for the Amlogic MesonX SoCs
MAINTAINERS: update ARM pxa maintainers
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
ARM: mvebu: Netgear RN102: Use Hardware BCH ECC
ARM: Kirkwood: Fix DT based DSA.
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: LPC32xx: Fix reset function
ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
...
Since we cannot make sure the 'pdata->num_leds' will always be none
zero here, and then if it equals to zero, the kmemdup() will return
ZERO_SIZE_PTR, which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmemdup().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This makes it possible to create a set of LEDs from a syscon
MFD instance, which is lean mean and clean on the ARM
reference designs and can replace the Versatile LEDs driver
in the long run, as well as other custom syscon LEDs drivers.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
[Fixed cocinelle warnings]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added driver to support the 14F021P00 BMC LEDs.
The BMC is a Board Management Controller including four LEDs which
can be switched on and off.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
led_update_brightness helper function used to be exploited only locally
in the led-class.c module, where its result was being passed to the
brightness_show sysfs callback. With the introduction of v4l2-flash
subdevice the same functionality becomes required for reading current
brightness from a LED device. This patch adds checking of return value
of the brightness_get callback and moves the led_update_brightness()
function to the LED subsystem public API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
When using a GPIO driver whose accessor functions may sleep (e.g. an
I2C GPIO extender like PCA9554) the following warning is issued:
WARNING: CPU: 0 PID: 665 at drivers/gpio/gpiolib.c:2274 gpiod_get_raw_value+0x3c/0x48()
Modules linked in:
CPU: 0 PID: 665 Comm: kworker/0:2 Not tainted 3.16.0-karo+ #115
Workqueue: events gpio_trig_work
[<c00142cc>] (unwind_backtrace) from [<c00118f8>] (show_stack+0x10/0x14)
[<c00118f8>] (show_stack) from [<c001bf10>] (warn_slowpath_common+0x64/0x84)
[<c001bf10>] (warn_slowpath_common) from [<c001bf4c>] (warn_slowpath_null+0x1c/0x24)
[<c001bf4c>] (warn_slowpath_null) from [<c020a1b8>] (gpiod_get_raw_value+0x3c/0x48)
[<c020a1b8>] (gpiod_get_raw_value) from [<c02f68a0>] (gpio_trig_work+0x1c/0xb0)
[<c02f68a0>] (gpio_trig_work) from [<c0030c1c>] (process_one_work+0x144/0x38c)
[<c0030c1c>] (process_one_work) from [<c0030ef8>] (worker_thread+0x60/0x5cc)
[<c0030ef8>] (worker_thread) from [<c0036dd4>] (kthread+0xb4/0xd0)
[<c0036dd4>] (kthread) from [<c000f0f0>] (ret_from_fork+0x14/0x24)
---[ end trace cd51a1dad8b86c9c ]---
Fix this by using the _cansleep() variant of gpio_get_value().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fix sparse warning appeared after changing brightness
type in the leds.h from int to enum led_brightness.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Make definition of the brightness related sysfs attributes
consistent. The modification entails change of the function
name: led_max_brightness_show -> max_brightness_show
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Reorder include directives so that they are arranged
in alphabetical order.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD which will be set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Link: https://lkml.kernel.org/r/1409417172-6846-5-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
Fixes the following sparse warnings:
drivers/leds/leds-ipaq-micro.c:130:24: warning:
symbol 'micro_leds_device_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds a driver for the iPAQ microcontroller LED.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The leds-atmel-pwm driver is now obsolete. It is not used by any mainlined
boards and is replaced by the generic leds_pwm with the pwm-atmel driver using
the generic PWM framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch converts the blink timer from led-core to workqueue which is more
suitable for this kind of non-priority operations. Moreover, timer may lead to
errors when a LED setting function use a scheduling function such as pinctrl
which is using mutex.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
PCA9632 defaults to open-drain
PCA9633/4/5 defaults to totem-pole
the driver assumed that totem-pole default and didn't actively set
the value; the MODE2 register is now written if platform
data indicating the mode is given
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the LED attributes
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Make sure the sysfs group is removed when the LEDs are unregistered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the src attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the blink attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the sata attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the sata attribute
during probe in order to avoid racing with userspace.
[cooloney@gmail.com: clean up return led_classdev_register()]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the mode attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the flash and
torch-LED attributes during probe in order to avoid racing with
userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the indicator-LED
attributes during probe in order to avoid racing with userspace.
Note that the comment about the pattern attribute only being for LM3554
was incorrect and did not match the code (the original leds-lm3556
driver had the attribute before LM3554 support was added).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the attributes
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the attribute groups of the led-class to create the mode attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Allow led-class devices to be created with optional attribute groups.
This is needed in order to allow led drivers to create custom device
attributes in a race-free manner.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull LED updates from Bryan Wu:
"I just found merge window is open and I'm quite busy and almost forget
to send out this pull request. Thanks Russell and Alexandre ping me
about this.
So basically we got some clean up and leds-pwm fixing patches from
Russell"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Remove duplicated OOM message for individual driver
drivers/leds: Replace __get_cpu_var use through this_cpu_ptr
leds: lp55xx: add DT bindings for LP55231
leds: 88pm860x: Fix missing refcount decrement for parent of_node
leds: 88pm860x: Use of_get_child_by_name
leds: leds-pwm: add DT support for LEDs wired to supply
leds: leds-pwm: implement PWM inversion
leds: leds-pwm: convert OF parsing code to use led_pwm_add()
leds: leds-pwm: provide a common function to setup a single led-pwm device
leds: pca9685: Remove leds-pca9685 driver
dell-led: add mic mute led interface
The majority of these changes are cleanups and fixes across all drivers.
Redundant error messages are removed and more PWM controllers set the
.can_sleep flag to signal that they can't be used in atomic context.
Support is added for the Broadcom Kona family of SoCs and the Intel LPSS
driver can now probe PCI devices in addition to ACPI devices. Upon shut-
down, the pwm-backlight driver will now power off the backlight. It also
uses the new descriptor-based GPIO API for more concise GPIO handling.
A large chunk of these changes also converts platforms to use the lookup
mechanism rather than relying on the global number space to reference
PWM devices. This is largely in preparation for more unification and
cleanups in future patches. Eventually it will allow the legacy PWM API
to be removed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BDxR
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The majority of these changes are cleanups and fixes across all
drivers. Redundant error messages are removed and more PWM
controllers set the .can_sleep flag to signal that they can't be used
in atomic context.
Support is added for the Broadcom Kona family of SoCs and the Intel
LPSS driver can now probe PCI devices in addition to ACPI devices.
Upon shutdown, the pwm-backlight driver will now power off the
backlight. It also uses the new descriptor-based GPIO API for more
concise GPIO handling.
A large chunk of these changes also converts platforms to use the
lookup mechanism rather than relying on the global number space to
reference PWM devices. This is largely in preparation for more
unification and cleanups in future patches. Eventually it will allow
the legacy PWM API to be removed"
* tag 'pwm/for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (38 commits)
pwm: fsl-ftm: set pwm_chip can_sleep flag
pwm: ab8500: Fix wrong value shift for disable/enable PWM
pwm: samsung: do not set manual update bit in pwm_samsung_config
pwm: lp3943: Set pwm_chip can_sleep flag
pwm: atmel: set pwm_chip can_sleep flag
pwm: mxs: set pwm_chip can_sleep flag
pwm: tiehrpwm: inline accessor functions
pwm: tiehrpwm: don't build PM related functions when not needed
pwm-backlight: retrieve configured PWM period
leds: leds-pwm: retrieve configured PWM period
ARM: pxa: hx4700: use PWM_LOOKUP to initialize struct pwm_lookup
ARM: shmobile: armadillo: use PWM_LOOKUP to initialize struct pwm_lookup
ARM: OMAP3: Beagle: use PWM_LOOKUP to initialize struct pwm_lookup
pwm: modify PWM_LOOKUP to initialize all struct pwm_lookup members
ARM: pxa: hx4700: initialize all the struct pwm_lookup members
ARM: OMAP3: Beagle: initialize all the struct pwm_lookup members
pwm: renesas-tpu: remove unused struct tpu_pwm_platform_data
ARM: shmobile: armadillo: initialize all struct pwm_lookup members
pwm: add period and polarity to struct pwm_lookup
pwm: twl: Really disable twl6030 PWMs
...
Pull HID patches from Jiri Kosina:
- RMI driver for Synaptics touchpads, by Benjamin Tissoires, Andrew
Duggan and Jiri Kosina
- cleanup of hid-sony driver and improved support for Sixaxis and
Dualshock 4, by Frank Praznik
- other usual small fixes and support for new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (29 commits)
HID: thingm: thingm_fwinfo[] doesn't need to be global
HID: core: add two new usages for digitizer
HID: hid-sensor-hub: new device id and quirk for STM Sensor hub
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard
HID: hid-sensor-hub: Set report quirk for Microsoft Surface
HID: debug: add labels for HID Sensor Usages
HID: uhid: Use kmemdup instead of kmalloc + memcpy
HID: rmi: do not handle touchscreens through hid-rmi
HID: quirk for Saitek RAT7 and MMO7 mices' mode button
HID: core: fix validation of report id 0
HID: rmi: fix masks for x and w_x data
HID: rmi: fix wrong struct field name
HID: rmi: do not fetch more than 16 bytes in a query
HID: rmi: check for the existence of some optional queries before reading query 12
HID: i2c-hid: hid report descriptor retrieval changes
HID: add missing hid usages
HID: hid-sony - allow 3rd party INTEC controller to turn off all leds
HID: sony: Add blink support to the Sixaxis and DualShock 4 LEDs
HID: sony: Initialize the controller LEDs with a device ID value
HID: sony: Use the controller Bluetooth MAC address as the unique value in the battery name string
...
The PWM core is now able to initialize the PWM period from a lookup
table defined by board files. Use it if available and fallback to the
value supplied in pwm_period_ns.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
I got a build error today, since LEDS_VERSATILE can be built-in while LEDS_CLASS
is a module:
drivers/built-in.o: In function `versatile_leds_probe':
:(.text+0x155020): undefined reference to `led_classdev_register'
I suggest we turn this option into 'tristate' so that the dependency
tracking works correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The OOM message of individual driver is unnecessary, and this is
duplicate the memory subsystem generic OOM message.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use this_cpu_ptr for the address calculation instead of __get_cpu_var.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The TI55231 appears to be fully compatible to the 5523 model from
National Semicondutor. This patch just adds DT bindings for it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver obtained the reference to parent->of_node but immediately it
was overwritten by reference to child node 'leds'. The of_node_put at
the end of DT parsing function decremented only the child 'leds' so
effectively the reference to parent of_node leaked.
Getting reference to parent->of_node is not needed at all so get rid of
it to fix the reference count.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use of_get_child_by_name to obtain reference to charger node instead of
of_find_node_by_name which can walk outside of the parent node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The non-DT driver allowed an active low property to be specified, but DT
is missing this in its description. Add the property to the DT binding
document, making it optional. It defaults to active high, which retains
compatibility with existing descriptions.
This should only be used for causes where the LED is wired to supply,
and the PWM does not sensibly support its own inversion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some PWM outputs are wired such that the LED they're controlling is
connected to supply rather than ground. These PWMs may not support
output inversion, or when they do, disabling the PWM may set the
PWM output low, causing a "brightness" value of zero to turn the LED
fully on.
The platform data for this driver already indicates that this was
thought about, and we have the "active_low" property there already.
However, the implementation for this is missing.
Add the trivial implementation for this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Convert the OF parsing code to use the common PWM LED registration code,
which means we have a consistent method, and single point where the
registration happens for both paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Provide a common function to setup a single led-pwm device, replacing
the platform data initialisation path with this function. This allows
us to have a common method of creating these devices in a consistent
manner, which then allows us to place the probe failure cleanup in one
place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This driver is replaced by pwm-pca9685 driver and there is no user uses this
driver in current tree. So remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch provides similar led functional of
420f973 thinkpad-acpi: Add mute and mic-mute LED functionality
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch refactors the way the thingm driver registers a blink(1) LED.
In order to make the driver simpler and more standard, drop the "rgb"
sysfs attribute and create one instance of LED class per RGB channel.
Actually, the name of the LED class instance registered for a blink(1)
device is "blink1::ABCD", where ABCD is the last 4 chars of the serial
number. The driver now registers 3 instances per RGB chip, named
"thingmX:{red,green,blue}:ledY" where X is the hidraw minor number and Y
is the RGB chip number (as seen by the firmware).
This patch also uses work queues to defer calls with the device, which
now allows triggers to work as expected with this LED device.
Also remove the brightness structure field and the brightness_get
backend, as it is already handled by the LED class, and changes the
prefix of functions and structures to thingm_ to match the driver name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull LED updates from Bryan Wu:
"This cycle we got:
- new driver for leds-mc13783
- bug fixes
- code cleanup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: make sure we unregister a trigger only once
leds: leds-pwm: properly clean up after probe failure
leds: clevo-mail: Make probe function __init
leds-ot200: Fix dependencies
leds-gpio: of: introduce MODULE_DEVICE_TABLE for module autoloading
leds: clevo-mail: remove __initdata marker
leds: leds-ss4200: remove __initdata marker
leds: blinkm: remove unnecessary spaces
leds: lp5562: remove unnecessary parentheses
leds: leds-ss4200: remove DEFINE_PCI_DEVICE_TABLE macro
leds: leds-s3c24xx: Trivial cleanup in header file
drivers/leds: delete non-required instances of include <linux/init.h>
leds: leds-gpio: add retain-state-suspended property
leds: leds-mc13783: Add devicetree support
leds: leds-mc13783: Remove unnecessary cleaning of registers on exit
leds: leds-mc13783: Use proper "max_brightness" value fo LEDs
leds: leds-mc13783: Use LED core PM functions
leds: leds-mc13783: Add MC34708 LED support
leds: Turn off led if blinking is disabled
ledtrig-cpu: Handle CPU hot(un)plugging
When probing with DT, we add each LED one at a time. If we find a LED
without a PWM device (because it is not available yet) we fail the
initialisation, unregister previous LEDs, and then by way of managed
resources, we free the structure.
The problem with this is we may have a scheduled and active work_struct
in this structure, and this results in a nasty kernel oops.
We need to cancel this work_struct properly upon cleanup - and the
cleanup we require is the same cleanup as we do when the LED platform
device is removed. Rather than writing this same code three times,
move it into a separate function and use it in all three places.
Fixes: c971ff185f ("leds: leds-pwm: Defer led_pwm_set() if PWM can sleep")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Now that we have converted this driver to a real platform device
module-based thing, we move the driver down into the LEDs
subsystem and rename the config option to LEDS_VERSATILE.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the benefits of platform_driver_probe() is that you can make
the probe function __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The Bachmann OT200 is a Geode-based device, so OT200-specific drivers
are only useful on X86_32, except for build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Enable autoloading of leds-gpio module when a corresponing DT entry is present.
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Remove __initdata marker, because it is not right for a module
parameter. It will make the kernel oops problem.
(cooloney@gmail.com: update commit message since it's really a
wrong notation)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Remove __initdata marker, because it is not right for a module
parameter. It will make the kernel oops problem.
(cooloney@gmail.com: update commit message since it's really a
wrong notation)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Remove unnecessary space in order to fix the following
checkpatch issues.
WARNING: space prohibited before semicolon
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jan-Simon Möller <dl9pf@gmx.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Remove unnecessary parentheses in order to fix the following
checkpatch error.
ERROR: return is not a function, parentheses are not required
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is deprecated.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some gpio-leds need retain the state even in suspend, such as charger led.
But this property missed in devicetree, add it.
(cooloney@gmail.com: fold DT binding updates into this patch)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds devicetree support for the MC13XXX LED driver.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LED core switches each LED to OFF-state on exit, so there is no need
for resetting registers.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Instead of using maximum value of 255 and shift it to appropriate
LED duty cycle, this patch introduce a helper to use proper maximum
value for each LED.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
