This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/core/message.c:1583:6: warning: symbol '__usb_queue_reset_device' was not declared. Should it be static?
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the USB core check the bandwidth when switching from one
interface alternate setting to another. Also check the bandwidth
when resetting a configuration (so that alt setting 0 is used). If
this check fails, the device's state is unchanged. If the device
refuses the new alt setting, re-instate the old alt setting in the
host controller hardware.
If a USB device doesn't have an alternate interface setting 0, install
the first alt setting in its descriptors when a new configuration is
requested, or the device is reset.
Add a mutex per root hub to protect bandwidth operations:
adding/reseting/changing configurations, and changing alternate interface
settings. We want to ensure that the xHCI host controller and the USB
device are set up for the same configurations and alternate settings.
There are two (possibly three) steps to do this:
1. The host controller needs to check that bandwidth is available for a
different setting, by issuing and waiting for a configure endpoint
command.
2. Once that returns successfully, a control message is sent to the
device.
3. If that fails, the host controller must be notified through another
configure endpoint command.
The mutex is used to make these three operations seem atomic, to prevent
another driver from using more bandwidth for a different device while
we're in the middle of these operations.
While we're touching the bandwidth code, rename usb_hcd_check_bandwidth()
to usb_hcd_alloc_bandwidth(). This function does more than just check
that the bandwidth change won't exceed the bus bandwidth; it actually
changes the bandwidth configuration in the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1298) fixes a bug in the new scatter-gather URB
facility. If an URB uses a scatterlist then it should not have the
URB_NO_INTERRUPT flag set; otherwise the system won't be notified when
the transfer completes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Vrabel <david.vrabel@csr.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The WHCI HCD will also support urbs with scatter-gather lists. Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD. Use this to decide whether to pass the scatter-list to the HCD
or not.
Make the usb-storage driver use this new field.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fix permits the "new" usbmon to access usb-storage's data buffer
without DMA remapping tricks. It should be compatible with PIO controllers
and not add any new crashes. Note that from now on PIO controllers and
usbmon are uniform in their access pattern and if one crashes then
the other will too. Hopefuly neither does.
As a side effect, we get rid for #ifdefs, which were a little ugly.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b7af0bb ("USB: allow malformed LANGID descriptors") broke support
for devices without string descriptor support.
Reporting string descriptors is optional to USB devices, and a device
lets us know it can't deal with strings by responding to the LANGID
request with a STALL token.
The kernel handled that correctly before b7af0bb came in, but failed
hard if the LANGID was reported but broken. More than that, if a device
was not able to provide string descriptors, the LANGID was retrieved
over and over again at each string read request.
This patch changes the behaviour so that
a) the LANGID is only queried once
b) devices which can't handle string requests are not asked again
c) devices with malformed LANGID values have a sane fallback to 0x0409
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the original patch I created before David Vrabel posted a better
patch (http://marc.info/?l=linux-usb&m=123377477209109&w=2) that does
basically the same thing. This patch will get replaced with his
(modified) patch later.
Allow USB device drivers that use usb_sg_init() and usb_sg_wait() to push
bulk endpoint scatter gather lists down to the host controller drivers.
This allows host controller drivers to more efficiently enqueue these
transfers, and allows the xHCI host controller to better take advantage of
USB 3.0 "bursts" for bulk endpoints.
This patch currently only enables scatter gather lists for bulk endpoints.
Other endpoint types that use the usb_sg_* functions will not have their
scatter gather lists pushed down to the host controller. For periodic
endpoints, we want each scatterlist entry to be a separate transfer.
Eventually, HCDs could parse these scatter-gather lists for periodic
endpoints also. For now, we use the old code and call usb_submit_urb()
for each scatterlist entry.
The caller of usb_sg_init() can request that all bytes in the scatter
gather list be transferred by passing in a length of zero. Handle that
request for a bulk endpoint under xHCI by walking the scatter gather list
and calculating the length. We could let the HCD handle a zero length in
this case, but I'm not sure if the core layers in between will get
confused by this.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally, the USB core had no support for allocating bandwidth when a
particular configuration or alternate setting for an interface was
selected. Instead, the device driver's URB submission would fail if
there was not enough bandwidth for a periodic endpoint. Drivers could
work around this, by using the scatter-gather list API to guarantee
bandwidth.
This patch adds host controller API to allow the USB core to allocate or
deallocate bandwidth for an endpoint. Endpoints are added to or dropped
from a copy of the current schedule by calling add_endpoint() or
drop_endpoint(), and then the schedule is atomically evaluated with a
call to check_bandwidth(). This allows all the endpoints for a new
configuration or alternate setting to be added at the same time that the
endpoints from the old configuration or alt setting are dropped.
Endpoints must be added to the schedule before any URBs are submitted to
them. The HCD must be allowed to reject a new configuration or alt
setting before the control transfer is sent to the device requesting the
change. It may reject the change because there is not enough bandwidth,
not enough internal resources (such as memory on an embedded host
controller), or perhaps even for security reasons in a virtualized
environment.
If the call to check_bandwidth() fails, the USB core must call
reset_bandwidth(). This causes the schedule to be reverted back to the
state it was in just after the last successful check_bandwidth() call.
If the call succeeds, the host controller driver (and hardware) will have
changed its internal state to match the new configuration or alternate
setting. The USB core can then issue a control transfer to the device to
change the configuration or alt setting. This allows the core to test new
configurations or alternate settings before unbinding drivers bound to
interfaces in the old configuration.
WIP:
The USB core must add endpoints from all interfaces in a configuration
to the schedule, because a driver may claim that interface at any time.
A slight optimization might be to add the endpoints to the schedule once
a driver claims that interface. FIXME
This patch does not cover changing alternate settings, but it does
handle a configuration change or de-configuration. FIXME
The code for managing the schedule is currently HCD specific. A generic
scheduling algorithm could be added for host controllers without
built-in scheduling support. For now, if a host controller does not
define the check_bandwidth() function, the call to
usb_hcd_check_bandwidth() will always succeed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1239) updates the kernel's treatment of Unicode. The
character-set conversion routines are well behind the current state of
the Unicode specification: They don't recognize the existence of code
points beyond plane 0 or of surrogate pairs in the UTF-16 encoding.
The old wchar_t 16-bit type is retained because it's still used in
lots of places. This shouldn't cause any new problems; if a
conversion now results in an invalid 16-bit code then before it must
have yielded an undefined code.
Difficult-to-read names like "utf_mbstowcs" are replaced with more
transparent names like "utf8s_to_utf16s" and the ordering of the
parameters is rationalized (buffer lengths come immediate after the
pointers they refer to, and the inputs precede the outputs).
Fortunately the low-level conversion routines are used in only a few
places; the interfaces to the higher-level uni2char and char2uni
methods have been left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the encoding of strings returned by usb_string() from ISO 8859-1
to UTF-8.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an USB hardware does not provide a valid LANGID, fall back to value
zero which is still a reasonable default for most devices.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
transfer_buffer_length and actual_length have become unsigned, therefore some
additional conversion of local variables, function arguments and print
specifications is desired.
A test for a negative urb->transfer_buffer_length became obsolete; instead
we ensure that it does not exceed INT_MAX. Also, urb->actual_length is always
less than urb->transfer_buffer_length.
rh_string() does no longer return -EPIPE in the case of an unsupported ID.
Instead its only caller, rh_call_control() does the check.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter. This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor! The
usb_get_string() routine needs to check whether it got the right
type of descriptor.
Oddly enough, this sort of check is already present in
usb_get_descriptor(). The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Guillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
===================================================================
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1197) fixes an error introduced recently. Since a
significant number of devices can't handle Set-Interface requests, we
no longer call usb_set_interface() when a driver unbinds from an
interface, provided the interface is already in altsetting 0. However
the interface still does get disabled, and the call to
usb_set_interface() was the only thing re-enabling it. Since the
interface doesn't get re-enabled, further attempts to use it fail.
So the patch adds a call to usb_enable_interface() when a driver
unbinds and the interface is in altsetting 0. For this to work
right, the interface's endpoints have to be re-enabled but their
toggles have to be left alone. Therefore an additional argument is
added to usb_enable_endpoint() and usb_enable_interface(), a flag
indicating whether or not the endpoint toggles should be reset.
This is a forward-ported version of a patch which fixes Bugzilla
#12301.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Roka <roka@dawid.hu>
Reported-by: Erik Ekman <erik@kryo.se>
Tested-by: Erik Ekman <erik@kryo.se>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1195) eliminates a potential problem identified by
Oliver Neukum. When a driver queues an asynchronous Set-Config
request using usb_driver_set_configuration(), the request should be
cancelled if userspace changes the configuration first. The patch
introduces a linked list of pending async Set-Config requests, and
uses it to invalidate the requests for a particular device whenever
that device's configuration is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1185) makes usbcore take advantage of the bus
notifications sent out by the driver core. Now we can create all our
device and interface attribute files before the device or interface
uevent is broadcast.
A side effect is that we no longer create the endpoint "pseudo"
devices at the same time as a device or interface is registered -- it
seems like a bad idea to try registering an endpoint before the
registration of its parent is complete. So the routines for creating
and removing endpoint devices have been split out and renamed, and
they are called explicitly when needed. A new bitflag is used for
keeping track of whether or not the interface's endpoint devices have
been created, since (just as with the interface attributes) they vary
with the altsetting and hence can be changed at random times.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a new call to be able to do a USB reset from an
atomic contect. This is quite helpful in USB callbacks to handle
errors (when the only thing that can be done is to do a device
reset).
It is done queuing a work struct that will do the actual reset. The
struct is "attached" to an interface so pending requests from an
interface are removed when said interface is unbound from the driver.
The call flow then becomes:
usb_queue_reset_device()
__usb_queue_reset_device() [workqueue]
usb_reset_device()
usb_probe_interface()
usb_cancel_queue_reset() [error path]
usb_unbind_interface()
usb_cancel_queue_reset()
usb_driver_release_interface()
usb_cancel_queue_reset()
Note usb_cancel_queue_reset() needs smarts to try not to unqueue when
it is actually being executed. This happens when we run the reset from
the workqueue: usb_reset_device() is called and on interface unbind
time, usb_cancel_queue_reset() would be called. That would deadlock on
cancel_work_sync(). To avoid that, we set (before running
usb_reset_device()) usb_intf->reset_running and clear it inmediately
after returning.
Patch is against 2.6.28-rc2 and depends on
http://marc.info/?l=linux-usb&m=122581634925308&w=2 (as submitted by
Alan Stern).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no need to take the address of the function params or local variables
when the direct value byteswapping routines are available.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1155) fixes a bug in usbcore. When interfaces are
deleted, either because the device was disconnected or because of a
configuration change, the extra attribute files and child endpoint
devices may get left behind. This is because the core removes them
before calling device_del(). But during device_del(), after the
driver is unbound the core will reinstall altsetting 0 and recreate
those extra attributes and children.
The patch prevents this by adding a flag to record when the interface
is in the midst of being unregistered. When the flag is set, the
attribute files and child devices will not be created.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.27, 2.6.26, 2.6.25]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Okay, I found the cause of the hang. It is a simple bug in the USB
scatter-gather library, caused by changes added in response to the S-G
chaining modification.
This patch (as1125) fixes a bug in the USB scatter-gather library.
Early exit from the S-G initialization loop does not reset the count of
outstanding URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is the usb interface driver probe() methods that
can't call usb_set_configuration, not usb device driver.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1103) changes the iteration in the USB scatter-gather to
use a standard SG iterator. Otherwise the iteration will fail if it
encounters a chained SG list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.
Unfortunately there are a few attributes which cannot be created that
early. The "descriptors" attribute is binary and so must be created
separately. The power-management attributes can't be created until
the dev/power/ group exists. And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I used ohci-sm501, hcd_alloc_coherent() in map_urb_for_dma() is not
called, because usb_sg_init() always sets URB_NO_TRANSFER_DMA_MAP.
dmesg (CONFIG_USB_STORAGE_DEBUG enabled):
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code -75; transferred 0/36
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x2
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removing an interface's sysfs files before unregistering the interface
doesn't work properly, because usb_unbind_interface() will reinstall
altsetting 0 and thereby create new sysfs files. This patch (as1074)
removes the files after the unregistration is finished. It's not
quite as clean, but at least it works.
Also, there's no need to check if an interface has been registered
before removing its sysfs files. If it hasn't been registered then
the files won't have been created, so usb_remove_sysfs_intf_files()
will simply do nothing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1048) extends the descriptor checking after a device is
reset. Now the SerialNumber string descriptor is compared to its old
value, in addition to the device and configuration descriptors.
As a consequence, the kmalloc() call in usb_string() is now on the
error-handling pathway for usb-storage. Hence its allocation type is
changed to GFO_NOIO.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request. A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Over two years ago, the Linux USB developers stated that they believed
there was no way to create a USB kernel driver that was not under the
GPL. This patch moves the USB apis to enforce that decision.
There are no known closed source USB drivers in the wild, so this patch
should cause no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1010) was written by both Kay Sievers and me. It solves
the problem of duplicated keys in USB uevent structures by refactoring
the uevent subroutines, taking advantage of the way the hotplug core
calls uevent handlers for the device's bus and for the device's type.
Keys needed for both USB-device and USB-interface events are added in
usb_uevent(), which is the bus handler. Keys appropriate only for
USB-device or USB-interface events are added in usb_dev_uevent() or
usb_if_uevent() respectively, the type handlers.
In addition, unnecessary tests for NULL pointers are removed as are
duplicated debugging log statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1009) solves the problem of multiple registrations for
USB sysfs files in a more satisfying way than the existing code. It
simply adds a flag to keep track of whether or not the files have been
created; that way the files can be created or removed as needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
This patch renames the IOMMU config option to GART_IOMMU because in fact it
means the GART and not general support for an IOMMU on x86.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch (as1005) fixes a rather subtle problem. When
usb_set_configuration() registers the interfaces and their files in
sysfs, it doesn't expect those files to exist already. But when an
interface is registered, its driver may call usb_set_interface() and
thereby cause the sysfs files to be created. The result is an error
when usb_set_configuration() goes on to create those same files again.
The (not-so-great) solution is to have usb_set_configuration() remove
any existing files before creating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
This patch (as988) breaks usb_hcd_endpoint_disable() apart into two
routines. The first, usb_hcd_flush_endpoint() does the -ESHUTDOWN
unlinking of all URBs in the endpoint's queue and waits for them to
complete. The second, usb_hcd_disable_endpoint() -- renamed for
better grammatical style -- merely calls the HCD's endpoint_disable
method. The changeover is easy because the routine currently has only
one caller.
This separation of function will be exploited in the following patch:
When a device is suspended, the core will be able to cancel all
outstanding URBs for that device while leaving the HCD's
endpoint-related data structures intact for later.
As an added benefit, HCDs no longer need to check for existing URBs in
their endpoint_disable methods. It is now guaranteed that there will
be none.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
