This patch adds #ifdef CONFIG_IWLWIFI_DEBUG in iwl_rx_reply_rx()
method in iwlwifi/iwl-rx.c) to avoid build error caused by "iwlwifi:
implement iwl_debug_report_frame for iwlagn".
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patches removes unused variable (pm_state) from iwl-dev.h and
from iwl-3945.h. (wireless-testing tree)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch protects iwlwifi indirect mmio operations with rmb() and
wmb(). It makes sure CPU reordering won't affect our indirect mmio
access.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch merges implementation of iwl_poll_bit() and
iwl_poll_direct_bit() by letting the latter be a special case of
the former.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the misue of CSR_GP_CNTRL with CSR_RESET address
in polling the CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY bit in
iwl4965_apm_reset(). This causes "MAC in deep sleep" error sometimes.
The patch also fixes the timeout value and the iwl_poll_bit() return
value check.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the misuse of microsecond with millisecond in the
polling mechanism of the iwlwifi driver. The impact of this problem
is the unacceptable latency for the whole system (especially during
bringing down the wlan interface).
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make sure we use only CCK rate for B only network.
For 3945 driver, it sets REPLY_RATE_SCALE command every time
we connect to a new network. In this command we set for every
rate the number of try and next rate. The problem mac80211 reports
same mode for both B and G mode as IEEE80211_BAND_2GHZ which will cause
using invalid rate other than CCK in B only network. THis patch
on association will examine sta valid rate on association, if no
OFDM rate in valid available rates it considers it as B only mode so
we can set REPLY_RATE_SCALE command with valid B only network and only
choose CCK rate in rate scaling.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old version of this code was copied from 3945 and never updated. This patch
cleans up structs that do not apply and accounts for other changes from
3945->iwlagn (e.g., PHY info can come in a separate cmd response from the
ucode.)
Signed-off-by: Daniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch does following things
1) This patch fixes the a-band association for passive channels with new
uCode feature that it allows direct scan on passive channels after
auto-switch from passive to active. This enables sending of direct probes
on passive channels, as long as some traffic is detected on that channel.
This improves the scanning for hidden SSIDs in A-band,which is all
passive channels.
This patch fixes the bug no 1748.
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1748
2) This fix will only work with uCode version 15.28.2.8 and above.
Prior versions of uCode would work only if we heard the traffic within
active dwell time, which is much shorter than passive dwell time and
is shorter than typical beacon periods. This patch also provids full
active dwell time even if we hear traffic late in passive dwell.
3) uCode API version is incremented to 2.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the infrastructure to support older firmware APIs.
The API version number is stored as part of the filename, we first try to
load the most recent firmware and progressively try lower versions.
The API version is also read from the firmware self and stored as part
of the iwl_priv structure. Only firmware that is supported by driver will
be loaded. The version number read from firmware is compared
to supported versions in the driver not the API version used as part of
filename.
An example using this new infrastrucure:
if (IWL_UCODE_API(priv->ucode_ver) >= 2) {
Driver interacts with Firmware API version >= 2.
} else {
Driver interacts with Firmware API version 1.
}
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We store the ucode version number as part of
iwl_priv/iwl3945_priv. This enables us to determine
if particular ucode has support for features in order
to have driver support more than one ucode API.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the misuse of DMA channel number by Tx queue number in
iwl_tx_ctx_stop().
The problem was originally reported by Wu Fengguang who complains
iwlagn driver takes too long time when issuing `ifconfig wlan0 down`.
The patch now decreases the interface bring down time from 2 seconds
to 0.8 second.
This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11956http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1790
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 rate scaling was broken in recent tree. This patch fix the following:
1- Get TX response info and update rates window.
2- Rate scaling selection.
3- Flush window timer.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add debugfs support to 3945 driver to display rs info.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves channels info display from sysfs to debugfs.
This shows channel information as stored in NIC EEPROM. This
is useful in debugging CRDA or iwl goes setting so it belongs
rather to debugfs then to sysfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_enable_interrupts and iwl_disable_interrupts
functions to iwl-core.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The find_station routine needs to look at the IWL_AP_ID entry if we're a STA.
Currently, it only looks for STA entries which causes HW crypto to fail.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_check_rxon_cmd into iwl-agn-hcmd-check.c
This function compiled out in none debugging or non development
mode and more. We haven't decided which one yet hence preserving the
current 'always compile' state.
More functions will be added to the file namely for checking TX and LQ
commands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables LO, TXIQ, and BB calibrations for 5150
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for 5150 eeprom versions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds computation of ct kill threshold
for 5150. Threshold is computed from calibration
data in the EEPROM.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables DC calibration for 5150
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi does not support AP mode in any way. For one, it doesn't even
buffer multicast/broadcast frames properly. We didn't allow zd1211rw AP
mode to be enabled without this, so iwlwifi shouldn't be allowed to
advertise AP mode either.
It also doesn't work at all, it doesn't even answer to probe requests,
I'm guessing the packet injection code was disabled again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 hardware does not emit the interrupts CSR_INT_BIT_RF_KILL (rfkill
toggled) and CSR_INT_BIT_CT_KILL (adapter too hot). Hence this part of code
can be removed since iwl3945_irq_tasklet does not handle 4965 hw at all.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base versions handle constant folding just fine.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
This patch also fixes a memory corruption problem reported in
http://marc.info/?l=linux-wireless&m=122641417231586&w=2 and tracked in
http://bugzilla.kernel.org/show_bug.cgi?id=12040.
When the key is removed a second time the offset is set to 255 - this
index is not valid for the ucode_key_table and corrupts the eeprom pointer
(which is 255 bits from ucode_key_table).
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Reported-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This instructs FH to increment the retry count of a packet when
it is brought from the memory to TX-FIFO to save transactions
during aggregation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures correctly TX DMA channel. It is not
the same as TX queue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apply same idiom as in 5000 introduced by
'iwlwifi: define firmware file name once'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds base band calibration support.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_clear_stations_table into iwl-sta.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the ad-hoc mode by
1) Removing redundant clear_stations_table which prevented generation of
beacons.
2) Setting assoc_id to 1. It was never set so preventing tx flow
in iwl3945_tx_skb.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables the custom firmware regulatory solution option
on iwlwifi drivers. These devices are uncapable of mapping their
EEPROM regulatory domain to a specific ISO / IEC alpha2.
Although the new 11n devices (>= iwl 5000) have only
3 regultaory SKUs -- MOW, ABG (no N) and BG -- the older
devices (3945 and 4965) have a more complex SKU arrangement
and therefore its not practical to move this to the driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix value of upper FH register bound plus
it reorders and groups registers in more readable way
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up some flow handler related document. It also
removes some blank lines.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch rewrites the mac80211 configure_filter handler to better mapping
mac80211 filter flags to iwlwifi hardware filter flags. We now can support
5 mac80211 filter flags: FIF_OTHER_BSS, FIF_ALLMULTI, FIF_PROMISC_IN_BSS,
FIF_BCN_PRBRESP_PROMISC and FIF_CONTROL. This patch also avoids reconnecting
if the filter flags are changed when the STA is associated. Because rx_assoc
is used when full rxon is not necessary.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use IWL_CCK_RATES_MASK and IWL_OFDM_RATES_MASK instead of
their values directly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch
1. Removes use once use only fc variables, they are useless after refactoring
ieee80211 frame control handlers
2. Other trivial cleanups
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code around and group most of the station
management code into iwl-sta.c
No functional changes (yet)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch aligns iwl3945_pci_probe with iwlwifi's iwl_pci_probe.
Added few comments and code simplified to make readable.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the RX DMA fix for iwlwifi ("iwlagn: fix RX skb alignment") Luis
pointed out:
> aligned_dma_addr can obviously be > real_dma_addr at this point, what
> guarantees we can use it on our own whim?
I asked around, and he's right, there may be platforms that do not allow
passing such such an address to the DMA API functions. This patch
changes it by using the proper dma_sync_single_range_for_cpu API
invented for this purpose.
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RCSR default value for single frame mode is off (a RB contains more than
one frames). But the driver assumes single frame mode apparently. This patch
enables single frame mode for the hardware. It also adds a BUG_ON to make sure
the allocated skb satisfies the hardware alignment requirement and removes
a useless check.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds additional info about wrong command queue bug
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved rate_msk calculation to iwl3945_rate_get_lowest_plcp.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
