* 'ubuntu-updates' of master.kernel.org:/pub/scm/linux/kernel/git/bcollins/ubuntu-2.6:
[pci_ids] Add Quicknet XJ vendor/device ID's.
[valkyriefb] Ifdef for when CONFIG_NVRAM isn't enabled.
[platinumfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[igafb] Add pci dev table for module auto loading.
[controlfb] Ifdef for when CONFIG_NVRAM isn't enabled.
[hid-core] TurboX Keyboard needs NOGET quirk.
[ixj] Add pci dev table for module auto loading.
[initio] Add pci dev table for module auto loading.
[fdomain] Add pci dev table for module auto loading.
[BusLogic] Add pci dev table for auto module loading.
[mv643xx] Add pci device table for auto module loading.
[alim7101] Add pci dev table for auto module loading.
This reverts earlier change that attempted to fix flow control.
Device needs to discard pause frames, otherwise it hangs after a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
When using flow control, the PHY needs to accept multicast pause frames.
Without this fix, these frames were getting discarded by the PHY before
doing any flow control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Under high load it is possible to make the receiver FIFO get overloaded.
The driver/hardware recover properly, so there is no reason to fill the log
with lots of extra messages, just update counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of flow control negotiation should not limit the next
negotiatition. If board is plugged into an old half duplex 10Mbit port,
without pause, then replugged into a gigabit port, it should negotiate
what is desired, not inherit that last negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The result of duplex negotiation is avaliable in the phy status
register, so use that to simplify code and avoid rereading the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
When PHY is turned off on shutdown, it causes the IRQ to get stuck on.
Make sure and disable the IRQ first, and if IRQ occurs when device
is not running, don't access PHY because that will hang.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The workaround timer is not needed in most systems with proper IRQ
routing and by perodically waking up it adds to laptop power consumption.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Some motherboards don't implement MSI correctly. The driver handles this
but the warning is too verbose and overly cautious.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
In preparation for moving check_signature, change these users from asm/io.h
to linux/io.h
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adjust the pause threshold on slower systems to keep from getting overrun.
Since FIFO is 2K bytes, don't send XON pause until there is space for a full
frame.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The pci express error handling extensions don't work unless PCI access is via
mmconfig. Otherwise, all accesses to pci config registers greater than 256 fail.
Since the sky2 driver has other ways of getting to PCI config space, it works
around this short coming, but the pci_find_ext_capablity doesn't work.
This backs out commit 91aeb3edbc
Go back to hardcoding, since we know where the error registers are anyway.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7222
Signed-off-by: Stephen Hemminger <shemmminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Want to be able to track downstream impact of fiber related
fixes.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do flow control negotiation properly. Don't let auto negotiation
status limit renegotiation. Separate desired pause values from
the result of auto negotiation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do correct mapping of pause and duplex when using 1000BaseX fiber
versions of the board.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PHY interrupt from the internal fiber is getting
stuck on when the link is down. Add code to handle the
transition and mask it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bugfix: rx descriptor release function fails to visit
the last entry while walking receive descriptor ring.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ring buffer descriptors are DMA-accessed bidirectionally,
but are not declared in this way. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cosmetic patch: give the variable holding the numer of descriptors
a more descriptive name, so to avoid confusion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current code attempts to start the TX dma every time a packet
is queued. This is too conservative, and wastes CPU time. This
patch changes behaviour to call the kick-dma function less often,
only when the tx queue is at risk of emptying.
This reduces cpu usage, improves performance.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove a dummy register read that is not needed.
This reduces CPU usage notably during transmit.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side of the spider ethernet driver currently
places locks around some very large chunks of code. This
results in a fair amount of lock contention is some cases.
This patch makes the locks much more fine-grained, protecting
only the cirtical sections. One lock is used to protect
three locations: the queue head and tail pointers, and the
queue low-watermark location.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves transmit queue cleanup code out of the
interrupt context, and into the NAPI polling routine.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement basic low-watermark support for the transmit queue.
Hardware low-watermarks allow a properly configured kernel
to continously stream data to a device and not have to handle
any interrupts at all in doing so. Correct zero-interrupt
operation can be actually observed for this driver, when the
socket buffer is made large enough.
The basic idea of a low-watermark interrupt is as follows.
The device driver queues up a bunch of packets for the hardware
to transmit, and then kicks the hardware to get it started.
As the hardware drains the queue of pending, untransmitted
packets, the device driver will want to know when the queue
is almost empty, so that it can queue some more packets.
If the queue drains down to the low waterark, then an interrupt
will be generated. However, if the kernel/driver continues
to add enough packets to keep the queue partially filled,
no interrupt will actually be generated, and the hardware
can continue streaming packets indefinitely in this mode.
The impelmentation is done by setting the DESCR_TXDESFLG flag
in one of the packets. When the hardware sees this flag, it will
interrupt the device driver. Because this flag is on a fixed
packet, rather than at fixed location in the queue, the
code below needs to move the flag as more packets are
queued up. This implementation attempts to keep the flag
at about 1/4 from "empty".
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bugfix -- the rx chain is in memory after the tx chain --
the offset being used was wrong, resulting in memory corruption
when the size of the rx and tx rings weren't exactly the same.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turn off mis-interpretation of the queue-empty interrupt
status bit as an error.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The print message associated with the descriptor chain end interrupt
prints a bogs value. Fix that.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current receive interrupt mask sets a bogus bit that doesn't even
belong to the definition of this register. Remove it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds a call to netif_stop_queue() when there is
no more room for more packets on the transmit queue.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the names of a few fields in the DMA control
register. There is no functional change.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Set the netdev watchdog timer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Polite device drivers pad short packets to 60 bytes,
so that mean-spirited users don't accidentally DOS
some other OS that can't handle short packets.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bugfix: when cleaning up the transmit queue upon device close,
be sure to walk the entire queue.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The module param permsissions should bw read-only, not writable.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch increases the Burst Address alignment from 64 to 1024 in the
Spidernet driver. This improves transmit performance for large packets.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds version information as reported by
ethtool -i to the Spidernet driver.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch includes a bug fix for the port state notification
and fixes the default queue sizes.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This eHEA patch covers required changes related to Anton Blanchard's new hvcall interface.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ibmveth.c:939: error: too many arguments to function `ibmveth_interrupt'
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes eeprom read on big-endian architectures.
readw returns the data in CPU order. With cpu_to_le16 we convert it to little
endian, because "ptr" is a pointer to a _byte_ arrray. See the cast above. A
byte array is little endian.
The bug is:
Reading u16 values with readw, casting them into an u8 array and accessing
this u8 array as an u8 (byte) array. The correct fix is to swap the
CPU-ordering value returned by readw into little endian, as the u8 array is
little endian.
This compiles to nothing on little endian hardware (so it does not change b44
code on LE hardware), but _fixes_ code on BE hardware.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>