When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The unsafe doorbell and scratchpad access should display reason when
WARN is called. Otherwise we get a stack dump without any explanation.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Printouts driver name and version to indicate what is being loaded.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k. Change the driver default to 64k.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Disable DMA usage by default, since the CPU provides much better
performance with write combining. Provide a module parameter to enable
DMA usage when offloading the memcpy is preferred.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Changing the memory window BAR mappings to write combining significantly
boosts the performance. We will also use memcpy that uses non-temporal
store, which showed performance improvement when doing non-cached
memcpys.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Allocate memory and request the DMA channel for the same NUMA node as
the NTB device.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the ntb transport is connecting and waiting for the peer, the debug
console receives lots of debug level messages about the remote qp link
status being down. Rate limit those messages.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a simple debugging driver that enables the doorbell and
scratch pad registers to be read and written from the debugfs. This
tool enables more complicated debugging to be scripted from user space.
This driver may be used to test that your ntb hardware and drivers are
functioning at a basic level.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a simple ping pong driver that exercises the scratch pads and
doorbells of the ntb hardware. This driver may be used to test that
your ntb hardware and drivers are functioning at a basic level.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On link down, don't advance RX index to the next entry. The next entry
should never be valid after receiving the link down flag.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport. Change the messages so they are distinct.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer. The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer. Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Commit ab760a0 (ntb: Adding split BAR support for Haswell platforms)
changed ntb_device's mw from a fixed-size array into a pointer that is
allocated based on limits.max_mw; however, on Atom platforms, max_mw
is not initialized until ntb_device_setup(), which happens after the
allocation.
Fill out max_mw in ntb_atom_detect() to match ntb_xeon_detect(); this
happens before the use of max_mw in the ndev->mw allocation.
Fixes a null pointer dereference on Atom platforms with ntb hardware.
v2: fix typo (mw_max should be max_mw)
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The MW regbase and vbase(s) were not being freed if an error occurred
in the vbase allocation loop. This is corrected by updating the error
path for the allocation loop to err4.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The PCI core now disables MSI and MSI-X for all devices during enumeration
regardless of CONFIG_PCI_MSI. Remove device-specific code to disable
MSI/MSI-X.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On the Haswell platform, a split BAR option to allow creation of 2
32bit BARs (4 and 5) from the 64bit BAR 4. Adding support for this
new option.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of using a module parameter, we should detect the errata via
PCI DID and then set an appropriate flag. This will be used for additional
errata later on.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
To simplify some of the platform detection code. Move the platform detection
to a function to be called earlier.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Move the platform detection function to separate functions to allow
easier maintenence.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Create a debugfs entry for the NTB device to log the basic device info,
as well as display the error count on a number of registers.
Signed-off-by: Jon Mason <jon.mason@intel.com>
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Signed-off-by: Jon Mason <jon.mason@intel.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
This is an cleanup effort to make ntb_setup_msix() more
readable - use ntb_setup_bwd_msix() to init MSI-Xs on
BWD hardware and ntb_setup_snb_msix() - on SNB hardware.
Function ntb_setup_snb_msix() also initializes MSI-Xs the
way it should has been done - looping pci_enable_msix()
until success or failure.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
In the code for Xeon devices in back-to-back mode with xeon_errata_workaround
disabled, the downstream device puts the wrong value in SNB_B2B_XLAT_OFFSETL
(SNB_MBAR01_DSD_ADDR vs. SNB_MBAR01_USD_ADDR).
This was spotted while reading code, since the typo has no practical effect,
at least for now: the low 32 bits of both constants are actually identical
anyway. However, it's clearer and safer to use the right name.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage. Also, clean-ups
to remove duplicate defines and document a hardware errata. Finally,
some changes to improve performance.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nOG2
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.13' of git://github.com/jonmason/ntb
Pull non-transparent bridge updates from Jon Mason:
"NTB driver bug fixes to address a missed call to pci_enable_msix,
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage.
Also, clean-ups to remove duplicate defines and document a hardware
errata. Finally, some changes to improve performance"
* tag 'ntb-3.13' of git://github.com/jonmason/ntb:
NTB: Disable interrupts and poll under high load
NTB: Enable Snoop on Primary Side
NTB: Document HW errata
NTB: remove duplicate defines
NTB: correct dmaengine_get/put usage
NTB: Fix ntb_transport link down race
ntb: Fix missed call to pci_enable_msix()
NTB: Fix NTB-RP Link Up
NTB: Xeon Doorbell errata workaround
Enable Snoop from Primary to Secondary side on BAR23 and BAR45 on all
TLPs. Previously, Snoop was only enabled from Secondary to Primary
side. This can have a performance improvement on some workloads.
Also, make the code more obvious about how the link is being enabled.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Remove duplicate defines in drivers/ntb/ntb_regs.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
dmaengine_get() causes the initialization of the per-cpu channel tables.
It needs to be called prior to dma_find_channel().
Initial version by Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
A WARN_ON is being hit in ntb_qp_link_work due to the NTB transport link
being down while the ntb qp link is still active. This is caused by the
transport link being brought down prior to the qp link worker thread
being terminated. To correct this, shutdown the qp's prior to bringing
the transport link down. Also, only call the qp worker thread if it is
in interrupt context, otherwise call the function directly.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Current MSI-X enablement code assumes MSI-Xs were successfully
allocated in case less than requested vectors were available.
That assumption is wrong, since MSI-Xs should be enabled with
a repeated call to pci_enable_msix(). This update fixes this.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
The Xeon NTB-RP setup, the transparent side does not get a link up/down
interrupt. Since the presence of a NTB device on the transparent side
means that we have a NTB link up, we can work around the lack of an
interrupt by simply calling the link up function to notify the upper
layers.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Modifications to the 14th bit of the B2BDOORBELL register will not be
mirrored to the remote system due to a hardware issue. To get around
the issue, shrink the number of available doorbell bits by 1. The max
number of doorbells was being used as a way to referencing the Link
Doorbell bit. Since this would no longer work, the driver must now
explicitly reference that bit.
This does not affect the xeon_errata_workaround case, as it is not using
the b2bdoorbell register.
Signed-off-by: Jon Mason <jon.mason@intel.com>
