It was accidentally added in commit 44ba2641 ("ASoC: dapm: Add support for DAI
multicodec").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a function helper to factorize the hw_params code.
Suggested by Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The platform field in the snd_soc_dapm_widget and snd_soc_dapm_context structs
is now unused can be removed. New code that wants to get the platform for a
widget or dapm context should use snd_soc_dapm_to_platform(w->dapm) or
snd_soc_dapm_to_platform(dapm).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds full DAPM support at the component level. Previously there was
only full DAPM support for CODECs and partial DAPM support (e.g. no Mixers nor
MUXs) for platforms. Having DAPM support at the component level will allow all
types of components to use DAPM and also help in consolidating the DAPM support
between CODECs and platforms.
Since the DAPM context is directly embedded into the snd_soc_codec and
snd_soc_platform struct and the 'dapm' field is directly referenced in a lot of
drivers moving the field just right now is not possible without causing code
churn. The approach this patch takes is to add two new fields to the component
struct. One field which is the pointer to the actual DAPM context used by the
component and one DAPM context that will be used as the default if no other
context was specified. For CODECs and platforms the pointer is initialized to
point to the CODEC or platform DAPM context. All generic code when referencing
a component's DAPM struct will go via the pointer. This will make it possible to
eventually seamlessly move the DAPM context from snd_soc_codec and
snd_soc_platform struct over once all direct references have been eliminated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the DAPM code directly looks at the CODEC driver struct to get a
handle to the set_bias_level() callback. This patch adds a new set_bias_level()
callback to the DAPM context struct. The DAPM code will use this new callback
instead of the CODEC callback. For CODECs the new callback is set up to call the
CODEC specific set_bias_level callback(). Not looking directly at the CODEC
driver struct will allow non CODEC DAPM contexts to implement a set_bias_level()
callback.
This is also similar to how the seq_notifier() and stream_event() callbacks are
currently handled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently only pins in CODEC DAPM contexts are automatically marked as
non-connected if the card has the fully_routed flag set. This makes sense since
widgets which qualify for auto-disconnection are only found in CODEC DAPM
contexts. But with componentisation this is going to change, so consider all
widgets for auto-disconnection.
Also it is probably faster to walk the widgets list only once rather than once
for each CODEC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The component struct already has a name and id field which are initialized to
the same values as the same fields in the CODEC and platform structs. So remove
them from the CODEC and platform structs and used the ones from the component
struct instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the name_prefix from the CODEC struct to the component struct. This will
eventually allow to specify prefixes for all types of components. It is also
necessary to make the DAPM code component type independent (i.e. a DAPM context
does not need to know whether it belongs to a CODEC or a platform or something
else).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit c9e065c27f ("ASoC: dapm: Make sure to always update the DAPM graph
in _put_volsw()") stopped updating register values in those cases where
initial after boot state of kcontrol appears to not change but where
register value still needs update because it is not in sync with the
kcontrol state.
Fix this by doing snd_soc_test_bits() unconditionally as it was before but
by using separate flags for kcontrol and register state changes. This allow
both DAPM graph to be updated when disabling auto-muted control and update
register if it is out-of-sync in respect of kcontrol state.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when the DAPM context bias level is SUSPEND and the target bias level
is OFF dapm_pre_sequence_async() will first transition to PREPARE and
dapm_post_sequence_async() will then transition back from PREPARE to STANDBY and
then to OFF.
This patch makes sure that dapm_pre_sequence_async() only transitions to PREPARE
when either going to ON or away from ON. This avoids the extra unnecessary
transitions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit commit de9ba98b6d ("ASoC: dapm: Make widget power register settings more
flexible") added generic support for on_val/off_val in the DAPM core. With this
in place there is no need anymore for having a special event callback for
SND_SOC_DAPM_REG() widgets.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we find a widget who's stream name matches the name of a DAI widget then
thats the one it should be connected to. Based on the widget id we can say in
which direction the path should be. No need to go back to the DAI and check the
stream names.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already know the widgets we want to connect, so use snd_soc_dapm_add_path()
instead of snd_soc_dapm_add_route() in snd_soc_dapm_new_pcm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already know which two widgets should be connected, so use
snd_soc_dapm_add_path() instead of snd_soc_dapm_add_route() in
snd_soc_dapm_connect_dai_link_widgets().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit bd23c5b661.
The patch claims that the patch is necessary to avoid double prefix addition
when calling snd_soc_dapm_add_route() from snd_soc_dapm_connect_dai_link_widgets().
But snd_soc_dapm_add_route() is called with the card's DAPM context, which does
not have a prefix, which means there is no prefix that could be added a second
time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC DAI links the paths are created in snd_soc_dapm_new_pcm().
Also for CODEC to CODEC links the widgets are connected cross-over via a DAI
link widget, meaning that the capture widget of one CODEC will be connected to
the playback widget of the other and vice versa. Whereas
snd_soc_dapm_connect_dai_link_widgets() directly connects the playback widget of
the CPU DAI to the playback widget of the CODEC DAI and the capture widget of
the CPU DAI to the capture widget of the CODEC DAI. So not skipping
CODEC<->CODEC links in snd_soc_dapm_connect_dai_link_widgets() will create
incorrect connections between the two CODECs which will cause DAPM to detect
active paths where there are none and unnecessarily power up widgets.
Fixes: b893ea5 ("ASoC: sapm: Automatically connect DAI link widgets in DAPM graph.")
Cc: <stable@vger.kernel.org> (for 3.14+)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When using auto-muted controls it may happen that the register value will not
change when changing a control from enabled to disabled (since the control might
be physically disabled due to the auto-muting). We have to make sure to still
update the DAPM graph and disconnect the mixer input.
Fixes: commit 5729507 ("ASoC: dapm: Implement mixer input auto-disable")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In soc_dapm_stream_event() we have the same code twice, once for the codec_dai
and once for the cpu_dai. This patch factors the duplicated code out into a
separate function. This will make it easier to modify the implementation (since
there is only one place that needs to be updated) and also easier to add support
for more than two DAIs per DAI link.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no unlocked version of soc_widget_update_bits_locked() and there is no
plan to introduce it in the near future, so drop the _locked suffix.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We currently have two very similar IO abstractions in ASoC, one for CODECs, the
other for platforms. Moving this to the component level will allow us to unify
those two. It will also enable us to move the standard kcontrol helpers as well
as DAPM support to the component level.
The new component level abstraction layer is primarily build around regmap.
There is a per component pointer for the regmap instance for the underlying
device. There are four new function snd_soc_component_read(),
snd_soc_component_write(), snd_soc_component_update_bits() and
snd_soc_component_update_bits_async(). They have the same signature as their
regmap counter-part and will internally forward the call one-to-one to regmap.
If the component it not using regmap it will fallback to using the custom IO
callbacks. This is done to be able to support drivers that haven't been
converted to regmap yet, but it is expected that this will eventually be removed
in the future once all component drivers have been converted to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 9e1fda4ae158 ("ASoC: dapm: Implement mixer input auto-disable")
is trying to free the widget it allocated by snd_soc_dapm_new_control()
call in dapm_kcontrol_data_alloc() by adding kfree(data->widget) to
dapm_kcontrol_free().
This is causing a widget double free with auto-disabled DAPM kcontrols
in sound card unregistration because widgets are already freed before
dapm_kcontrol_free() is called.
Reason for that is all widgets are added into dapm->card->widgets list
in snd_soc_dapm_new_control() and freed in dapm_free_widgets() during
execution of snd_soc_dapm_free().
Now snd_soc_dapm_free() calls for different DAPM contexts happens before
snd_card_free() call from where the call chain to dapm_kcontrol_free()
begins:
soc_cleanup_card_resources()
soc_remove_dai_links()
soc_remove_link_dais()
snd_soc_dapm_free(&cpu_dai->dapm)
soc_remove_link_components()
soc_remove_platform()
snd_soc_dapm_free(&platform->dapm)
soc_remove_codec()
snd_soc_dapm_free(&codec->dapm)
snd_soc_dapm_free(&card->dapm)
snd_card_free()
snd_card_do_free()
snd_device_free_all()
snd_device_free()
snd_ctl_dev_free()
snd_ctl_remove()
snd_ctl_free_one()
dapm_kcontrol_free()
This wasn't making harm with ordinary DAPM kcontrols since data->widget is NULL for
them.
Fixes: 9e1fda4ae158 (ASoC: dapm: Implement mixer input auto-disable)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch change reg's type from unsigned short to int.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to spot locking issues by asserting that the DAPM mutex is held when
it should be. There's a bit of fun due to us not requiring the lock to be
held prior to the card being instantiated which mean we need to wrap the
assert in some paths and this isn't methodical by any stretch of the
imagination.
Signed-off-by: Mark Brown <broonie@linaro.org>
The new sequence ensure that dapm_pre_sequence_async work on
the card before all codecs and dapm_post_sequence_async work
on the card after all codecs.
So the machine driver could utilize the determinate sequence
to do the gloabl setup and teardown in the right place.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The widgets generated by the machine driver need to power off too.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are three different completely independent code paths in
dapm_set_path_status(). One of them is never used at all and the other two (one
for mixers, one for MUXs) have their distincive callsites that always go onto
the same path. Breaking the function into two parts allows us to reduce the code
size and in the MUX case also do some optimizations to avoid having to calcualte
the selected item for each item again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
MUXs and virtual MUXs are almost identical, the only difference is that for
virtual MUX there is no hardware backing register in which setting is stored.
This patch adds code, which is similar to what we already do for DAPM mixer
controls to support virtual mixer controls, to DAPM enum controls. The new code
will check if the enum does a hardware backing register and skip over reading
and writing to the register if it has not. This allows us to use the same code
path for both MUXs and virtual MUXs and a lot of nearly identical code can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
MUXs and value MUXs are almost identical, the only difference is that a value
MUX uses a look-up table to map from the selected control item to a register
value, while MUXs use a direct mapping. This patch uses
snd_soc_enum_item_to_val() and snd_soc_enum_val_to_item(), which where earlier
introduced during the consolidation of enum and value enum controls, to hide
this difference. This allows us to use the same code path for both MUXs and
value MUXs and a lot of nearly duplicated code can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We will often call sync after several functions that require the DAPM
mutex to be held. Rather than release and immediately relock the mutex
provide an unlocked function for this situation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The snd_soc_dapm_xxxx_pin all require the dapm_mutex to be held when
they are called as they edit the dirty list, however very few of the
callers do so.
This patch adds unlocked versions of all the functions replacing the
existing implementations with one that holds the lock internally. We
also fix up the places where the lock was actually held on the caller
side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The name "max" in struct soc_enum is rather confusing since it
actually takes the number of items. With "max", one might try to
assign (nitems - 1) value.
Rename the field to a more appropriate one, "items", which is also
used in struct snd_ctl_elem_info, too.
This patch also rewrites some code like "if (x > e->nitems - 1)" with
"if (x >= e->nitems)". Not only the latter improves the readability,
it also fixes a potential bug when e->items is zero.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The error messages for bypassing/unbypassing a regulator appear to be
swapped round, this patch corrects these.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit f7d3c1709 ("ASoC: dapm: Change prototype of soc_widget_read") changed the
signature of soc_widget_read() so that it, instead of return the register value
as a int, takes a pointer to a unsigned int and stores the register value in
that pointer. There are still a few places that pass a int type value to that
function though. Change these to unsigned int. For more consistency also change
the signature of soc_widget_write() to take a unsigned int instead of an int for
the register value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The prefix for the codec driver can be used during dual identical
codec usecases. However, dapm adds prefix twice for codec DAI widget
in snd_soc_dapm_add_route API.
This change is to avoid double prefix addition for codec DAI widget
and is needed while using identical dual codecs.
Signed-off-by: Songhee Baek <sbaek@nvidia.com>
Signed-off-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_widget_read API returns the register data and it is possible
that a register can contain 0xffffffff. Thus, change the prototype
of soc_widget_read to return only the error code and pass the reg
data through pointer argument.
Signed-off-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Connect the DAPM graph through each BE DAI link to the componnent(s) on the
other side of the BE DAI link. This allows the graph to be walked on
both sides of the link when graph changes are made.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM can dynamically alter the FE to BE PCM links at runtime based
on mixer/mux setting updates. Add soc_dpcm_runtime_update() calling in
get/put function for mixer/mux to support this feature.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some additional fixes for v3.13, the majority of which are removals and
downgrades of BUG()s from Takashi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=osG+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.13
Some additional fixes for v3.13, the majority of which are removals and
downgrades of BUG()s from Takashi.
Leaving BUG_ON() in a core layer like dapm is rather inappropriate as
it leads to panic(), even though sanity checks might be still useful
for debugging.
Instead, Use WARN_ON(), and handle the error cases accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
BUG() used in the driver is just to spit the stack trace on buggy
points, not really needed to stop the whole operation. For that
purpose, it'd be more convenient to use WARN() instead with more
error information.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
... instead of NULL dereferences.
Spotted by coverity CID 402004.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
... due to a copy & paste error.
Spotted by coverity CID 710923.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
In order to avoid trying to use an external clock or supply for an
on-chip supply prior to it being enabled move the clock and regulator
supply events to a separate step in DAPM sequencing from normal supply
events.
This should have minimal practical impact since these widgets are sorted
using SND_SOC_NOPM which is a negative value and hence sorted
separately to any real register writes, though it may be relevant if
supplies have event callbacks only.
Signed-off-by: Mark Brown <broonie@linaro.org>
Within a DAPM sequence we normally don't care about when exactly a register
write has completed so long as they happen in the order we requested. This
means that we can issue most of the writes we do asynchronously which
should maximise the ability of the underlying frameworks to keep the
hardware busy, providing a small performance improvement on some systems.
We currently ensure that all writes are completed both when changing to a
different device and when calling into the regulator and clock frameworks.
This should ensure that the previous ordering is maintained.
We also ensure that writes are completed prior to calling into widget
event functions since some event functions implement delays. This
should be improved in future so that widgets can disable this sync in
order to add extra writes.
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for virtual DAPM mixer controls. They are similar to
virtual DAPM enums. There is no hardware register backing the control, so
changing the control's value wont have any direct effect on the hardware. But it
still influences the DAPM graph by causing the path it sits on to be connected
or disconnected. This in turn can cause power changes for some of the widgets on
the DAPM graph, which will then modify the hardware state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
VMID widgets behave very similar to signal generator widgets. Both are always
considered to be powered up. This means that we need to ignore the VMID widgets
in the same way as signal generator widgets when calculating the DAPM context's
target bias level. Otherwise the presence of a VMID widget, regardless whether
it is on an active path or not, will cause the DAPM context to be powered up.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We need to make sure that the control's cached value is initialized to the same
value as the control's widget->on_val. Otherwise updates might be lost.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current calls to dapm_mark_dirty() in snd_soc_dapm_add_path() are on a path
that is only reached if the sink widget is either a mixer or a mux. Move the
calls further up so they are called for all widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure that the recently added path kcontrol list is initialised otherwise
we may crash trying to delete routes that don't have kcontrols.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Attempting to create the route as part of adding a mux control causes us
to attempt to add the same route twice since we loop over all sources
for the mux after creating the control. Instead do the addition in the
callers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
ASoC automatically creates snd_soc_dapm_dai_in and snd_soc_dapm_dai_out
widgets for DAI drivers, and adds them to the list. Later on, ASoC
creates automatic routes between these widgets and a widget with a
stream name.
We look for a snd_soc_dapm_dai_in or snd_soc_dapm_dai_out widget, and
use this to obtain the DAI structure. We then scan all widgets for
any with a stream name refering to either the capture or the playback
stream, and create routes.
If you have both a snd_soc_dapm_dai_in and a snd_soc_dapm_dai_out
referring to the same DAI structure, this ends up creating one set of
routes for the DAI for the snd_soc_dapm_dai_in widget, and a duplicated
set of routes for the snd_soc_dapm_dai_out widget.
Fix this by checking that the stream name for the widget matches the
DAI widget name.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some devices have the problem that if a internal audio signal source is disabled
the output of the source becomes undefined or goes to a undesired state (E.g.
DAC output goes to ground instead of VMID). In this case it is necessary, in
order to avoid unwanted clicks and pops, to disable any mixer input the signal
feeds into or to active a mute control along the path to the output. Often it is
still desirable to expose the same mixer input control to userspace, so cerain
paths can sill be disabled manually. This means we can not use conventional DAPM
to manage the mixer input control. This patch implements a method for letting
DAPM overwrite the state of a userspace visible control. I.e. DAPM will disable
the control if the path on which the control sits becomes inactive. Userspace
will then only see a cached copy of the controls state. Once DAPM powers the
path up again it will sync the userspace setting with the hardware and give
control back to userspace.
To implement this a new widget type is introduced. One widget of this type will
be created for each DAPM kcontrol which has the auto-disable feature enabled.
For each path that is controlled by the kcontrol the widget will be connected to
the source of that path. The new widget type behaves like a supply widget,
which means it will power up if one of its sinks are powered up and will only
power down if all of its sinks are powered down. In order to only have the mixer
input enabled when the source signal is valid the new widget type will be
disabled before all other widget types and only be enabled after all other
widget types.
E.g. consider the following simplified example. A DAC is connected to a mixer
and the mixer has a control to enable or disable the signal from the DAC.
+-------+
+-----+ | |
| DAC |-----[Ctrl]-| Mixer |
+-----+ : | |
| : +-------+
| :
+-------------+
| Ctrl widget |
+-------------+
If the control has the auto-disable feature enabled we'll create a widget for
the control. This widget is connected to the DAC as it is the source for the
mixer input. If the DAC powers up the control widget powers up and if the DAC
powers down the control widget is powered down. As long as the control widget
is powered down the hardware input control is kept disabled and if it is enabled
userspace can freely change the control's state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
list_first_entry() will always return a valid pointer, even if the list is
empty. So the check whether path is NULL will always be false. So we end up
calling dapm_create_or_share_mixmux_kcontrol() with a path struct that points
right in the middle of the widget struct and by trying to modify the path the
widgets memory will become corrupted. Fix this by using list_emtpy() to check if
the widget doesn't have any paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
When calling krealloc for the kcontrol data the items in the path list that
point back to the head of the list will now point to freed memory, which causes
the list to become corrupted. To fix this, instead of resizing the whole data
struct, only resize the widget list.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_cnew() can return NULL, so we should check the result before trying to
use it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a typo here so we end up using the old freed pointer instead of
the newly allocated one. (If the "n" is zero then the code works,
obviously).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wait with updating the widgets power field until the changes are actually
written to the hardware in dapm_seq_run_coalesced(). This will allow us to query
the current hardware state between calling dapm_power_one_widget() and actually
writing the new power state to hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_add_path() is similar to snd_soc_dapm_add_route() except that it
expects the pointer to the source and sink widgets instead of their names. This
allows us to simplify the case where we already have a pointer to widgets. (E.g.
as we have in snd_soc_dapm_link_dai_widgets()). snd_soc_dapm_add_route() will be
updated to just look up the widget and then use snd_soc_dapm_add_path() to
handle everything else.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the DAPM code is limited to only setting or clearing a single bit in a
register to power a widget up or down. This patch extends the DAPM code to be
more flexible in that regard and allow widgets to use arbitrary values to be
used to put a widget in either on or off state.
Since the snd_soc_dapm_widget struct already contains a on_val and off_val field
no additional fields need to be added and in fact the invert field can even be
removed. Also the generated code is slightly smaller.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we store for each path which control (if any at all) is associated
with that control. But we are only ever interested in the reverse relationship,
i.e. we want to know all the paths a certain control is associated with. This is
currently implemented by always iterating over all paths. This patch updates the
code to keep a list for each control which contains all the paths that are
associated with that control. This improves the run time of e.g.
soc_dapm_mixer_update_power() and soc_dapm_mux_update_power() from O(n) (with n
being the number of paths for the card) to O(1).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 'value' field is really per control and not per widget. Currently it is only
used for virtual MUXes, which only have one control per widget. So in that case
there is not so much of a difference between whether it is stored per widget or
per control. Moving the 'value' field from the widget to the control will allow
us to use it also for cases where we have more than one control per widget. E.g.
for mixers with multiple input controls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for adding additional per control data wrap all access to the
widget list in helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use the same 3 lines to get the CODEC for a kcontrol in a quite a few places.
This patch puts them into a common helper function. Having this encapsulated in
a helper function will also make it more easier to eventually change the data
layout of the kcontrol's private data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
DAPM operations are always performed on the card as a whole. Yet (primarily for
historic reasons) dapm_power_widgets() takes a DAPM context as its parameter.
The DAPM context is mainly used to look up a pointer to the card. The same is
true for a couple of functions that are being called from dapm_power_widgets().
This patch changes the signature of dapm_power_widgets() and a couple of related
functions to take a snd_soc_card instead of a snd_soc_dapm_context.
Some of the functions also use the DAPM's device to print error and debug
messages. This can be a bit confusing though since this means the messages for
all widgets, also those from other contexts, will be printed with that device.
The patch updates those cases to use the device of the widget's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The update field of a DAPM context is only assigned while the card's dapm_mutex
is locked, the field is also cleared again while the mutex is stil locked. So
there will only ever be one DAPM context at a time with a non-NULL update field.
So it is safe to move the update field from the DAPM context struct to the card
struct. Doing so will allow further cleanups in this area.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to avoid race conditions the assignment of dapm->update should happen
while card->dapm_mutex is being held. To allow CODEC drivers to run a register
update when using snd_soc_dapm_mux_update_power() or
snd_soc_dapm_mixer_update_power() add a update parameter to these two functions.
The update parameter will be assigned to dapm->update while card->dapm_mutex is
locked.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when updating a control that is shared between multiple widgets the
whole power-up/power-down sequence is being run once for each widget. The
control register is updated during the first run, which means the CODEC internal
routing is also updated for all widgets during this first run. The input and
output paths for each widgets are only updated though during the respective run
for that widget. This leads to a slight inconsistency between the CODEC's
internal state and ASoC's state, which causes non optimal behavior in regard to
click and pop avoidance.
E.g. consider the following setup where two MUXs share the same control.
+------+
A1 ------| |
| MUX1 |----- C1
B1 ------| |
+------+
|
control ---+
|
+------+
A2 ------| |
| MUX2 |----- C2
B2 ------| |
+------+
If the control is updated to switch the MUXs from input A to input B with the
current code the power-up/power-down sequence will look like this:
Run soc_dapm_mux_update_power for MUX1
Power-down A1
Update MUXing
Power-up B1
Run soc_dapm_mux_update_power for MUX2
Power-down A2
(Update MUXing)
Power-up B2
Note that the second 'Update Muxing' is a no-op, since the register was already
updated.
While the preferred order for avoiding pops and clicks should be:
Run soc_dapm_mux_update_power for control
Power-down A1
Power-down A2
Update MUXing
Power-up B1
Power-up B2
This patch changes the behavior to the later by running the updates for all
widgets that the control is attached to at the same time.
The new code is also a bit simpler since callers of
soc_dapm_{mux,muxer}_update_power don't have to loop over each widget anymore
and neither do we need to keep track for which of the kcontrol's widgets the
current update is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_dpcm_runtime_update() operates on a ASoC card as a whole. Currently it takes
a snd_soc_dapm_widget as its only parameter though. The widget is then used to
look up the card and is otherwise unused. This patch changes the function to
take a pointer to the card directly. This makes it possible to to call
soc_dpcm_runtime_update() for updates which are not related to one specific
widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As noticed by Lars-Peter Clausen since the move to using widgets to hook
into the DAIs we no longer directly manage the power of AIF or DAC/ADC
widgets from the stream integration so they can just use the generic power
checks instead of the custom stream integration ones they currently do.
Signed-off-by: Mark Brown <broonie@linaro.org>
The ALSA core expect the put callback of a control to return 1 if the value of
the control changed and 0 if it did not. Both snd_soc_dapm_put_volsw() and
snd_soc_dapm_put_enum_virt() currently always returns 0. For both functions we
already have a 'change' variable which either contains 1 or 0 depending on
whether the value has changed or not, so just return that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
These two functions were added two years ago in commit 4805608 ("ASoC: dapm -
Add methods to retrieve snd_card and soc_card from dapm context.") but have
remained unused so far. Considering that the dapm context actually has a direct
pointer to the card the functions also seem to be unnecessary. E.g. the
expressions 'dapm_get_soc_card(dapm)' and 'dapm->card' yield the same result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power up/down sequence order for DAPM switch widgets is not explicitly
initialized, causing them to be run always as the first widget type for both
power up and down. Move it to the same position in the sequence as other mixer
widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for freeing a DAPM path in three different locations.
Introduce a new helper function to take care of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The condition 'i == item' is only true when, well, 'i' equals 'item'.
So just use 'item' directly as the index into the array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The private data containing the widget list that is a assigned to a DAPM
kcontrol is never freed. Setup the private_free for DAPM kcontrols to take care
of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though they are virtual widgets DAI widgets still get counted for the
DAPM context power management so we can't just use the active state to
check if they should be powered as they may not be part of a complete path.
Instead split them into input and output widgets and do the same power
checks as we perform on AIFs.
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power_list field is used when adding a widget to a power sequence list. Use
the same field when iterating the list using list_for_each_entry, otherwise
we'll see undefined behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
kasprintf calculates the size of the result string, allocates a buffer large
enough to hold the string and then performs the format string operation. There
are a couple of places in ASoC where these three steps are done by hand and
where kasprintf can be used instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices may benefit from being able to start some parts of the widget
power up/down sequence earlier on in the sequence than the point at which
the final power state is committed. Support these by providing events which
are called before any power state changes are done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WQzu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
