This patch moves iwl_clear_stations_table into iwl-sta.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the ad-hoc mode by
1) Removing redundant clear_stations_table which prevented generation of
beacons.
2) Setting assoc_id to 1. It was never set so preventing tx flow
in iwl3945_tx_skb.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the mac address in add_interface and clear it in
remove_interface so that users can change the mac address
to something other than the one in the eeprom. Also avoid
setting it at attach time so that we won't ack packets
until fully set up.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_CCK flag is set for all 2 Ghz channels, so IS_CHAN_CCK() would
turn out to be true for all channles in that band.
Use IS_CHAN_B() now, which checks the channel mode and not the channel
flags.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, use a helper function to setup RC status data
when processing completed TX descriptors.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Break down huge functions, use helper functions or
macros instead.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace TRUE/FALSE macros with VALID/INVALID macros.
Follow a consistent variable convention.
Remove unnecessary comments.
Add all RC phy macros into a single enum.
Merge functions into reasonably sized entities.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintaining two sets of rate tables is redundant, remove one
and use struct ath_rate_table exclusively.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the hack using vif, and use rate_driver_data within
skb->cb to hold driver specific rate information.
Setup the rate series in the skb's tx control area and remove
all references to ath9k specific rate series ( using struct ath_rc_series ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the hw rate tables to ath_softc, and access them directly.
tx_triglevel_max is global, move it to ath_rate_node.
Now that ath_rate_softc is gone, rate control attach becomes simpler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control init is now confined to itself, using the
HT capabilites of the STA from rate_init().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a lot of old, crufty code and make
RX status reporting a bit sane and clean.
Do not do anything to the RX skb before unmapping.
So in ath_rx_tasklet(), move the skb_put() after PCI unmap.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Half/Quarter rate tables are needed only for legacy chipsets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup legacy rates in ath_rate_init() itself.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid casting of ath_tx_ratctrl and access the elements directly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the commit entitled "mac80211/drivers: rewrite the rate control
API", the meaning of the packet transmit count was changed from the
number of retries to the total number. In driver rtl8187, this change
was missed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we switch off the LEDS during initialization
we kill rt73usb from proper functioning. The immediate
result after the first LED command are MCU failures
and a complete breakdown of TX/RX.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since WE7 /proc/net/wireless checks whether level and noise are in dBm
and shows them accordingly. Indicate that we return signal and noice
levels in dBm.
Before:
Inter-| sta-| Quality | Discarded packets | Missed | WE
face | tus | link level noise | nwid crypt frag retry misc | beacon | 22
eth1: 0000 65. 219. 165. 0 0 148 41 0 0
After:
Inter-| sta-| Quality | Discarded packets | Missed | WE
face | tus | link level noise | nwid crypt frag retry misc | beacon | 22
eth1: 0000 65. -37. -91. 0 0 0 0 0 0
While at it, replace raw numbers with appropriate macro.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hp-plus uses 8390p.c, so it should use eip_poll(), not ei_poll().
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0x9cbd): undefined reference to `ei_poll'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can just use common ei_netdev_ops definition.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By having common code in 8390.o don't need net_dev_ops in
the driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert both eisa and mca versions of this driver, though I doubt
anyone still has the hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another driver converted to new infrastructure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another driver converted to net_device_ops; Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the defactoring of ei_XXX functions in 8390 and 8390p.
Remove the tx_timeout hack since no driver including the 3c503
overrides tx_timeout at this time, looks like a legacy thing.
Also, since several drivers all have same hooks, provide common
netdev_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix warning:
drivers/net/3c523.c:582: warning: ‘cleanup_card’ defined but not used
No code changed:
md5:
ebe4a1b27d3f21b0b12a78c58463b0d7 3c523.o.before.asm
ebe4a1b27d3f21b0b12a78c58463b0d7 3c523.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix warning:
drivers/net/depca.c: In function ‘depca_eisa_probe’:
drivers/net/depca.c:1564: warning: ‘mem_start’ may be used uninitialized in this function
this seems to be a real bug - depca_eisa_probe() does not check
for failure. Add it, symmetric to depca_isa_probe().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this warning:
drivers/net/atlx/atl2.c: In function ‘atl2_request_irq’:
drivers/net/atlx/atl2.c:644: warning: unused variable ‘err’
'err' is unused in the !CONFIG_PCI_MSI case.
Instead of further increasing the #ifdeffery in this function,
restructure the code a bit and get rid of the #ifdef. This
relies on the fact that pci_enable_msi() will always fail in
the !CONFIG_PCI_MSI case.
There should be no change in driver behavior.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix warning:
drivers/net/mlx4/mcg.c: In function ‘mlx4_multicast_attach’:
drivers/net/mlx4/mcg.c:217: warning: integer overflow in expression
there was no real danger of overflow here though.
md5:
db8eb55620f886c03854a2abb2ce6c3f mcg.o.before.asm
db8eb55620f886c03854a2abb2ce6c3f mcg.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/cassini.c: In function ‘cas_rx_ringN’:
drivers/net/cassini.c:2350: warning: ‘skb’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between cas_rx_process_pkt() and 'skb'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/mlx4/en_rx.c: In function ‘mlx4_en_activate_rx_rings’:
drivers/net/mlx4/en_rx.c:412: warning: ‘err’ may be used uninitialized in this function
Triggers because 'err' is uninitialized in the following input
conditions: priv->rx_ring_num is zero and mlx4_en_fill_rx_buffers()
fails.
But even if ->rx_ring_num is nonzero, 'err' will be zero if
mlx4_en_fill_rx_buffers() fails and mlx4_en_activate_rx_rings() returns
success - incorrectly.
So it's best to keep the error code uptodate on mlx4_en_fill_rx_buffers()
calls as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/wan/z85230.c: In function ‘z8530_interrupt’:
drivers/net/wan/z85230.c:713: warning: ‘intr’ may be used uninitialized in this function
is clearly bogus - annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/sis900.c: In function ‘sis900_timer’:
drivers/net/sis900.c:1280: warning: ‘speed’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between sis900_read_mode(), 'speed' and 'duplex'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/qla3xxx.c: In function ‘ql3xxx_probe’:
drivers/net/qla3xxx.c:3912: warning: ‘pci_using_dac’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between 'pci_using_dac' and 'err'.
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/niu.c: In function ‘esr_reset’:
drivers/net/niu.c:741: warning: ‘reset’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between:
- esr_read_reset() and 'reset'
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
these warnings:
drivers/net/niu.c: In function ‘serdes_init_niu_1g_serdes’:
drivers/net/niu.c:451: warning: ‘sig’ may be used uninitialized in this function
drivers/net/niu.c: In function ‘serdes_init_niu_10g_serdes’:
drivers/net/niu.c:550: warning: ‘sig’ may be used uninitialized in this function
triggers because GCC does not recognize that the max_retry loop
always initializes 'sig', due to max_retry != 0.
Annotate them.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
this warning:
drivers/net/s2io.c: In function ‘rx_intr_handler’:
drivers/net/s2io.c:7369: warning: ‘lro’ may be used uninitialized in this function
triggers because GCC does not recognize the (correct) error flow
between:
- s2io_club_tcp_session()and 'lro'
Annotate it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A patch to put names on the niu interrupt vectors according the syntax below.
This is needed to assign correct affinity.
> So on a multiqueue card with 2 RX queues and 2 TX queues we'd
> have names like:
>
> eth0-rx-0
> eth0-rx-1
> eth0-tx-0
> eth0-tx-1
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the poor wireless connection which happens even
if we are very well in the range.
Signed-off-by: Don.breslin@atheros.com
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As was pointed out in "p54: honour bss_info_changed's short slot time settings",
bss_info_changed provides more useful settings that can be used by the driver.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes pointed out that the driver has cache the firmware for
suspend/resume cycles.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains only contains a one-liner fixes and enhancements
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables Mesh Point operation for any p54 device.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the DMAable mameory consistent with pci_set_consistent_dma_mask().
The DMA-mapping.txt Documentation recommends this but for PCI-X
considerations and on strange architecture like SGI SN2, not sure
why it would fix an issue but lets see if it does, just in case.
Before this, this driver was tested with x86_64 with about
7 GB of RAM, not sure if this is really needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use DMA_32BIT_MASK to clarify we only want 32-bit DMA
memory. What was there before is also 32-bit but this makes it
clearer
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the used in/out endpoints
we should detect them by walking through all
available endpoints.
rt2800usb will gain the most out of this, because
the legacy drivers indicate that there are multiple
endpoints available.
However this code might benefit at least rt73usb as
well for the MIMO queues, and if we are really lucky
rt2500usb will benefit because for the TX and PRIO
queues.
Even if rt2500usb and rt73usb do not get better performance
after this patch, the endpoint detection still belongs to
rt2x00usb, and it shouldn't hurt to always try to detect
the available endpoints.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After considerable testing, the initial fears that the driver might damage
some flavors of RTL8187B hardware seem to be groundless. Accordingly, the
logged warning is removed. In addition, Kconfig is changed to remove the
dependence on EXPERIMENTAL.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Realtek 8187B has a receive command queue to feedback beacon interrupt
and transmitted packet status. Use it to feedback mac80211 about status
of transmitted packets. Unfortunately in the course of testing I found
that the sequence number reported by hardware includes entire sequence
control in a 12 bit only field, so a workaround is done to check only
lowest bits.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add conf_tx callback and use it to configure tx queues of 8187L/8187B.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hin-Tak Leung reported that after the change "rtl8187: add short slot
handling for 8187B" his RTL8187B started to give low throughput on
network transfers. Turns out that the SIFS setting used isn't ok, it
doesn't look to be the real aSIFSTime, using the "magical" 0x22 value
like on other 818x variants as the vendor does too fixes the issue.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Race condition causes RX buffers to be accessed even before it is
initialized. The RX and TX buffers are initialized immediately after
the hardware is registered with mac80211. The mac80211 start callback
is ready to be fired once the device is registered for a case when the
wpa_supplicant is also running at the same time.
The same race condition is also possible for RKFILL registration
as RFKILL init happens after the device registration with mac80211
and it is possible that rfkill_register would be called even before
it is initialized.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k frees irq even before IRQs are disabled and existing IRQs
are flushed when rfkill_register() fails.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ath9k builds RFKILL feature only when the RFKILL subsystem
is built part of the kernel. Build RFKILL feature regardless of whether
RFKILL subsystem is built as a MODULE or part of the kernel.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
init values update for various atheros chipsets.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables the custom firmware regulatory solution option
on iwlwifi drivers. These devices are uncapable of mapping their
EEPROM regulatory domain to a specific ISO / IEC alpha2.
Although the new 11n devices (>= iwl 5000) have only
3 regultaory SKUs -- MOW, ABG (no N) and BG -- the older
devices (3945 and 4965) have a more complex SKU arrangement
and therefore its not practical to move this to the driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix value of upper FH register bound plus
it reorders and groups registers in more readable way
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up some flow handler related document. It also
removes some blank lines.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch rewrites the mac80211 configure_filter handler to better mapping
mac80211 filter flags to iwlwifi hardware filter flags. We now can support
5 mac80211 filter flags: FIF_OTHER_BSS, FIF_ALLMULTI, FIF_PROMISC_IN_BSS,
FIF_BCN_PRBRESP_PROMISC and FIF_CONTROL. This patch also avoids reconnecting
if the filter flags are changed when the STA is associated. Because rx_assoc
is used when full rxon is not necessary.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use IWL_CCK_RATES_MASK and IWL_OFDM_RATES_MASK instead of
their values directly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch
1. Removes use once use only fc variables, they are useless after refactoring
ieee80211 frame control handlers
2. Other trivial cleanups
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code around and group most of the station
management code into iwl-sta.c
No functional changes (yet)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch aligns iwl3945_pci_probe with iwlwifi's iwl_pci_probe.
Added few comments and code simplified to make readable.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback function write_tx_data() can only fail
when our ENTRY_OWNER_DEVICE_DATA flag on a queue entry
failed to determine the entry was not available and
it is in fact still owned by the hardware.
This means that if that function fails the queue
must be stopped in mac80211.
When rt2x00queue_get_queue() returns NULL in the TX
path, it means mac80211 has passed us an invalid queue,
although this should be impossible, it shouldn't hurt
if we send mac80211 a signal to stop the queue either.
Both issues can simply be resolved by removing their
manual failure handler and making them use the failure path
provided in rt2x00mac_tx().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb and rt73usb have different register word sizes,
for that reason the register access wrappers were never
moved into rt2x00usb.
With rt2800usb on its way, we should favor the 32bit
register access and move those wrappers into rt2x00usb.
That saves duplicate code, since only rt2500usb will
need the special 16bit wrappers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.
This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call the ath5k pci driver struct "ath5k" too to be less
confusing in sysfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ath5k driver has too many interrupts per second at idle
http://bugzilla.kernel.org/show_bug.cgi?id=11749
Signed-off-by: Martin Xu <martin.xu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
http://bugzilla.kernel.org/show_bug.cgi?id=12076
Remove any write access to groups and others, only keep write permission
to its owner, usually only root user.
Reported-by: Jérôme Poulin <jeromepoulin@gmail.com>
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should only tell the hardware its capable of DMA'ing
to us only what we asked dev_alloc_skb(). Prior to this
it is possible a large RX'd frame could have corrupted
DMA data but for us but we were saved only because we
were previously also pci_map_single()'ing the same large
value. The issue prior to this though was we were unmapping
a smaller amount which the prior DMA patch fixed.
Signed-off-by: Bennyam Malavazi <Bennyam.Malavazi@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should fix the SW-IOMMU bounce buffer starvation
seen ok kernel.org bugzilla 11811:
http://bugzilla.kernel.org/show_bug.cgi?id=11811
Users on MacBook Pro 3.1/MacBook v2 would see something like:
DMA: Out of SW-IOMMU space for 4224 bytes at device 0000:0b:00.0
Unfortunately its only easy to trigger on MacBook Pro 3.1/MacBook v2
so far so its difficult to debug (even with swiotlb=force).
We were pci_unmap_single()'ing less bytes than what we called
for with pci_map_single() and as such we were starving
the swiotlb from its 64MB amount of bounce buffers. We remain
consistent and now always use sc->rxbufsize for RX. While at
it we update the beacon DMA maps as well to only use the data
portion of the skb, previous to this we were pci_map_single()'ing
more data for beaconing than what we tell the hardware it can use,
therefore pushing more iotlb abuse.
Still not sure why this is so easily triggerable on
MacBook Pro 3.1, it may be the hardware configuration
tends to use more memory > 3GB mark for DMA.
Signed-off-by: Maciej Zenczykowski <zenczykowski@gmail.com>
Signed-off-by: Bennyam Malavazi <Bennyam.Malavazi@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the RX DMA fix for iwlwifi ("iwlagn: fix RX skb alignment") Luis
pointed out:
> aligned_dma_addr can obviously be > real_dma_addr at this point, what
> guarantees we can use it on our own whim?
I asked around, and he's right, there may be platforms that do not allow
passing such such an address to the DMA API functions. This patch
changes it by using the proper dma_sync_single_range_for_cpu API
invented for this purpose.
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change forces the bits to 0 by using an &= operation with an inverted
mask of all options instead of using an |= with a value of 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a reference to a Buffer Size extention bit that is unneded by
82575/82576 hardware. Since it is not needed it should be removed from the
code.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option. In addition, added useful help text for the
Kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY is mostly compatible with the existing VSC8244 PHY. The init sequence
is different and the interrupt mask lacks some bits present in the VSC8244.
Rather than making a copy of the existing VSC234x config_intr function and
change one constant, I modify it to select the interrupt mask based on
which driver is calling it. This lets it be used by both drivers.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made usb_drivers reset_resume function point to hso_resume this
fixes problems a usb reset is done when the network interface
is left idle for a few minutes. Possibly reset_resume should
initialise hardware more but this works in the common case.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes TIOCM ioctls for Data Carrier Detect & related functions
work like /drivers/serial/serial-core.c potentially needed
for pppd & similar user programs.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new structure hso_mutex_table had to be declared statically
& used as as hso_device mutex_lock(&serial->parent->mutex) etc
is freed in hso_serial_open & hso_serial_close by kref_put while
the mutex is still in use.
This is a substantial change but should make the driver much stabler.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added check for IFF_UP in hso_resume, this should eliminate -EINVAL (-22)
errors caused from urb's being submitted twice, once by hso_resume
& once in hso_net_open, if suspend/resume USB power saving mode is enabled
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved serial_open_count in hso_serial_open to
prevent crashes owing to the serial structure being made NULL
when hso_serial_close is called even though hso_serial_open
returned -ENODEV, Alan Cox pointed out this happens,
also put in sanity check in hso_serial_close
to check for a valid serial structure which should prevent
the most reproducable crash in the driver when the hso device
is disconnected while in use.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. convert netdev->priv to netdev_priv().
2. make sbni_pci_probe() be static.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing previously allocated buffers in case of error.
Signed-off-by: Jirka Pirko <jirka@pirko.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointed out by Joe Perches. Error message after tx_ring allocation check was
wrong.
Signed-off-by: Jirka Pirko <jirka@jirka.pirko.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed typo when allocating rx_ring, tx_ring was checked for null instead.
Signed-off-by: Jirka Pirko <jirka@pirko.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using call by reference use the PTR_ERR macros to handle
return value with error case. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4e4fd4e485 ("ne2k: convert to
net_device_ops") exported some ei_* symbols from the 8390 library,
but the axnet_cs driver defines local static versions of the same
functions.
Rename them to avoid the namespace conflict.
Reported by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the igb driver is experiencing a panic due to a null function
pointer being used during the cleanup of the ethtool looback test on
fiber/serdes parts. This patch prevents that and adds a check prior to
calling any phy function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarrify reading PBA has no side-effect (clearing).
Add missing GPL license text.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver/firmware compatibility check.
Update firmware notify cmd to honor notify area size.
Add new version of init cmd.
Add link_down_cnt to notify area to track link down count.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ethtool support for get/set_flags so LRO can be turned on/off
by fwding drivers such as the bridge driver. LRO is not compatible
with fwding drivers.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supporting both original SCA and SCA-II in one file was nice at some
point but now it's increasingly painful.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Convert driver to new net_device_ops. Compile tested only.
This required some additional work to export common code ei_XXX.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
