Xeon55xx fails to probe with this error message:
EDAC DEBUG: in drivers/edac/i7core_edac.c, line at 1660: MC: drivers/edac/i7core_edac.c: i7core_init()
EDAC i7core: Device not found: dev 00:00.0 PCI ID 8086:2c41
i7core_edac: probe of 0000:00:14.0 failed with error -22
This is due to the fact that, on Xeon35xx (and i7core), device 00.0 has
PCI ID 8086:2c40.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
m->bank is not related to the memory bank but, instead, to the MCA Error
register bank. Fix it accordingly. While here, improves the comments for
Nehalem bank.
A later fix is needed, in order to get bank/rank information from MCA
error log.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enriches mcelog error by using the encoded information at MCE status and
misc registers (IA32_MCx_STATUS, IA32_MCx_MISC).
Some fixes are still needed here, in order to properly fill the EDAC
fields.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some Nehalem architectures have more than one MC socket. Socket 0 is
located at bus 255.
Currently, it is using up to 2 sockets, but increasing it to a larger
number is just a matter of increasing MAX_SOCKETS definition.
This seems to be required for properly support of Xeon 55xx.
Still needs testing with Xeon 55xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code changes the detection procedure of i7core_edac. Instead of
directly probing for MC registers, it probes for another register found
on Nehalem. If found, it tries to pick the first MC PCI BUS. This should
work fine with Xeon 35xx, but, on Xeon 55xx, this is at bus 254 and 255
that are not properly detected by the non-legacy PCI methods.
The new detection code scans specifically at buses 254 and 255 for the
Xeon 55xx devices.
This code has not tested yet. After working, a change at the code will
be needed, since the i7core is not yet ready for working with 2 sets of
MC.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The public Intel Xeon 5500 volume 2 datasheet describes, on page 53,
session 2.6.7 a register that can lock/unlock Memory Controller the
configuration register, called MC_CFG_CONTROL.
Adds support for it in the hope that software error injection would
work. With my tests with Xeon 35xx, there's still something missing.
With a program that does sequencial bit writes at dev 0.0, sometimes, it
produces error injection, after unblocking the MC_CFG_CONTROL (and,
sometimes, it just locks my testing machine).
I'll try later to discover by trial and error what's the register that
solves this issue on Xeon 35xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a glue code to allow i7core to work with mcelog. With the glue,
i7core registers itself on edac_mce. At mce, when an error is detected,
it calls all registered drivers (in this case, i7core), for EDAC error
handling.
TODO: It currently just prints the MCE error log using about the same
format as mce panic messages. The error message should be enhanced
with mcelog userspace info and converted into the proper EDAC format,
to feed the EDAC error counts.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
edac_mce module is an interface module that gets mcelog data and
forwards to any registered edac module that expects to receive data via
mce.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function appears only on Xeon 5500 datasheet. Yet, testing with a
Xeon 3503 showed that this is also implemented on other Nehalem
processors.
At the first read, MC_TEST_ERR_RCV1 and MC_TEST_ERR_RCV0 can contain any
value. Modify CE error logic to update the error count only after the
second read.
An alternative approach would be to do a write at rcv0 and rcv1
registers, but it seemed better to keep they untouched, since BIOS might
eventually assume that they are exclusive for their usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some locking troubles with edac_core: if you don't declare an
edac_check, module may suffer from soft lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implements set_inject_error() with the low-level code needed to inject
memory errors at Nehalem, and adds some sysfs nodes to allow error injection
The next patch will add an API for error injection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is meant to support i7 core/i7core extreme desktop
processors and Xeon 35xx/55xx series with integrated memory controller.
It is likely that it can be expanded in the future to work with other
processor series based at the same Memory Controller design.
For now, it has just a few MCH status reads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
ARM: 6030/1: KS8695: enable console
ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
ARM: fix build error in arch/arm/kernel/process.c
In current implementation of PL061, setting type of irq to HIGH_LEVEL is not
working. This patch fixes this bug.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pktcdvd driver uses proper locking and does not need the BKL in the
ioctl and llseek functions of the character device, so kill both.
Moving the compat_ioctl handling from common code into the driver itself
fixes build problems when CONFIG_BLOCK is disabled.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
sfc: Change falcon_probe_board() to fail for unsupported boards
sfc: Always close net device at the end of a disabling reset
sfc: Wait at most 10ms for the MC to finish reading out MAC statistics
sctp: Fix oops when sending queued ASCONF chunks
sctp: fix to calc the INIT/INIT-ACK chunk length correctly is set
sctp: per_cpu variables should be in bh_disabled section
sctp: fix potential reference of a freed pointer
sctp: avoid irq lock inversion while call sk->sk_data_ready()
Revert "tcp: bind() fix when many ports are bound"
net/usb: add sierra_net.c driver
cdc_ether: fix autosuspend for mbm devices
bluetooth: handle l2cap_create_connless_pdu() errors
gianfar: Wait for both RX and TX to stop
ipheth: potential null dereferences on error path
smc91c92_cs: spin_unlock_irqrestore before calling smc_interrupt()
drivers/usb/net/kaweth.c: add device "Allied Telesyn AT-USB10 USB Ethernet Adapter"
bnx2: Update version to 2.0.9.
bnx2: Prevent "scheduling while atomic" warning with cnic, bonding and vlan.
bnx2: Fix lost MSI-X problem on 5709 NICs.
cxgb3: Wait longer for control packets on initialization
...
The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by commit
eb9f6744cb "sfc: Implement ethtool
reset operation".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code would wait indefinitely if MAC stats DMA failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
coda: move backing-dev.h kernel include inside __KERNEL__
mtd: ensure that bdi entries are properly initialized and registered
Move mtd_bdi_*mappable to mtdcore.c
btrfs: convert to using bdi_setup_and_register()
Catch filesystems lacking s_bdi
drbd: Terminate a connection early if sending the protocol fails
drbd: fix memory leak
Fix JFFS2 sync silent failure
smbfs: add bdi backing to mount session
ncpfs: add bdi backing to mount session
exofs: add bdi backing to mount session
ecryptfs: add bdi backing to mount session
coda: add bdi backing to mount session
cifs: add bdi backing to mount session
afs: add bdi backing to mount session.
9p: add bdi backing to mount session
bdi: add helper function for doing init and register of a bdi for a file system
block: ensure jiffies wrap is handled correctly in blk_rq_timed_out_timer
Fix regulator enabling issue that is caused by typo error in is_enabled().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This ensures that the translations for unmapped IO mappings or
unmapped memory are properly removed from the MMU hash table
before such an unplug. Without this, the hypervisor refuses the
unplug operations due to those resources still being mapped by
the partition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Re-submitted based on comments from netdev community.
Summary of the changes:
1. Improved error handling.
2. Added the missing timeout arguments to usb_control_msg().
The following is a new Linux driver which exposes certain models of Sierra
Wireless modems to the operating system as Network Interface Cards (NICs).
This driver requires a version of the sierra.c driver which supports
blacklisting to work properly. The blacklist in sierra.c rejects the interfaces
claimed by sierra_net.c. Likewise, the sierra_net.c driver only accepts
(i.e. whitelists) the interface(s) used for USB-to-WWAN traffic.
The version of sierra.c which supports blacklisting is
available from the sierra wireless knowledge base page for older kernels. It is
also available in Linux kernel starting from version 2.6.31.
This driver works with all Sierra Wireless devices configured with PID=68A3
like USB305, USB306 provided the corresponding firmware version is I2.0
(for USB305) or M3.0 (for USB306) and later.
This driver will not work with earlier firmware versions than the ones shown
above. In this case the driver will issue an error message indicating
incompatibility and will not serve the device's USB-to-WWAN interface.
Sierra_net.c sits atop a pre-existing Linux driver called usbnet.c.
A series of hook functions are provided in sierra_net.c which are called by
usbnet.c in response to a particular condition such as receipt or transmission
of a data packet. As such, usbnet.c does most of the work of making
a modem appear to the system as a network device and for properly exchanging
traffic between the USB subsystem and the Network card interface.
Sierra_net.c is concerned with managing the data exchanged between the
USB-to-WWAN interface and the upper layers of the operating system.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Rory Filer <rfiler@sierrawireless.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autosuspend works until you bring the wwan interface up, then the
device does not enter autosuspend anymore.
The following patch fixes the problem by setting the .manage_power
field in the mbm_info struct to the same as in the cdc_info struct
(cdc_manager_power).
Signed-off-by: Torgny Johansson <torgny.johansson@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped. We need to wait for both, or the
controller could get into an invalid state.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bill Gatliff reported the following bug when using the irq_chip facility
of the pca953x driver on a PPC platform:
BUG: scheduling while atomic: insmod/1530/0x00000002
He traced it back to an i2c transaction in pca953x_irq_set_type(), which
can be called with interrupt disabled (from __setup_irq()). As the i2c
controller can sleep while sending a message, this qualifies as a bad
idea.
This patch moves the i2c transaction to pca953x_irq_bus_sync_unlock(),
where it is actually safe to send an i2c message.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Reported-by: Bill Gatliff <bgat@billgatliff.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The calls to usb_free_buffer() dereference rx_urb and tx_urb in the
parameter list but those could be NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91c92_cs:
* spin_unlock_irqrestore before calling smc_interrupt() in media_check()
to avoid lockup.
* use spin_lock_irqsave for ethtool function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver calls ndo_vlan_rx_register() while holding bond->lock.
The bnx2 driver calls bnx2_netif_stop() to stop the rx handling while
changing the vlgrp. The call also stops the cnic driver which sleeps
while the bond->lock is held and cause the warning.
This code path only needs to stop the NAPI rx handling while we are
changing the vlgrp. Since no reset is going to occur, there is no need
to stop cnic in this case. By adding a parameter to bnx2_netif_stop()
to skip stopping cnic, we can avoid the warning.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
