This adds the necessary Kconfig entry for a Snowball board.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
This sets up a few GPIO pins and some pinmuxing on platform boot
for the Snowball board. Based on work from Mathieu J. Poirier
<mathieu.poirier@linaro.org>.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
With SDI support for the Snowball we can boot from the
SD card.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
The UART setting in uncompress.h changes on the Snowball board.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Based on work from Mathieu J. Poirier <mathieu.poirier@linaro.org>
For more information on snowball please visit
http://www.igloocommunity.org
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
The PRCMU TCDM memory needs to be iomapped for the PRCMU to work
properly.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This board now has complete regulation constraints and can turn
off unused regulators. For the moment we need to wire VAUX1
(V-DISPLAY rail) always on since it somehow affects the external
MMC.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We cannot clock the MMCI blocks more than 50 MHz. A bug prevented
us from seeing the effect of actually driving them to 100 MHz,
which indeed resulted failure, on the external SD card.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a regression on the HREFv60 ux500 hardware: the wrong
level shifter was addressed in the MMCI vdd handler, trying to
reconfigure an unclaimed GPIO pin.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The DB8500v2 and DB5500 has a fifth version of the "PL023" and
PL180 blocks. However the ASIC engineers have forgot to bump the
revision in the PrimeCell peripheral ID registers. Since the
platform is aware of the actual silicon revision we need to
hard-code the periphid from the platform, bumping the subrevision
field to 1.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is redundant. The correct ID number is right there in the
hardware anyway. We will introduce a mechanism later to hard-code
this for deviant cells.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This specifies the new per-platform timeout per I2C bus and
switches the I2C buses to fast mode, and increase the FIFO
depth to 8 for reads and writes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The DB8500 has ePOD:s (electronic power domains) which are possible
to switch on/off to deactivate silicon blocks on the DB8500 SoC
by cutting their power without retention. We model these as simple
regulators with one bit on/off settings.
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As part of the ARM arch subsystem migration, move the DB8500
cpufreq driver to drivers/cpufreq as discussed with Dave Jones. The
Makefile is not updated in order to avoid cross-subsystem conflicts
for this file in merges.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the DB5500 PRCMU driver. Right now this one is pretty
restricted in functionality, exposing a simple interface to send
I2C messages.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the DB8500 PRCMU driver to the latest version
available internally. Nominally we would update the dependent
CPUfreq driver at the same time but since that is being moved
around in this patch set we postpone that by simply deactivating
it for the time being.
This is a snapshot of the current PRCMU firmware API as it looks
right now. The PRCMU firmware is still subject to change. This
also updates the CPUfreq driver to a newer version that will
utilize the new API.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Sebastien Rault <sebastien.rault@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have decided that this function arbiter fits better in the MFD
subsystem. Since we need to concatenate the split header files we move
it basically like this:
mv mach-ux500/prcmu-db8500.c drivers/mfd/db8500-prcmu.c
mv mach-ux500/include/mach/prcmu-defs.h include/linux/mfd/db8500-prcmu.h
mv mach-ux500/include/mach/prcmu-regs.h drivers/mfd/db8500-prcmu-regs.h
mach-ux500/include/mach/prcmu.h >> include/linux/mfd/db8500-prcmu.h
rm arch/arm/mach-ux500/include/mach/prcmu.h
Then we update different #include statements and Makefile orders etc
to make the PRCMU driver compile, link and boot in the new place
without really changing any code.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the PRCMU base address be selected at runtime for U8500
and U5500 instead of being compiled-in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the core detect the DB8500 V2.0 and V2.1 ASICs, and
add a convenience macro for "V2 or later".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This splits out a per-SoC IRQ range handling, so that the
DB8500 and DB5500 SoC:s can reuse aproximately the same IRQ
range with the largest span setting the roof. The same change
is done for the boards, mutatis mutandis, with a new file for
the U5500 board.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
Commit e2a083dc0da9aa6437e14811198379b18cdfa7f8
"ARM: consolidate SMP cross call implementation" broke the ux500
compilation since the smp.h header declared a function called
from headsmp.S. This fixes it up by declaring it locally instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Adding two sets of I2C devices to the same bus doesn't quite work,
atleast not anymore. Stash one array and determine how much of it
shall be added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the TPS61052 regulator to the ux500 MOP/HREF boards.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds an ab8500 regulator initialization vector for the
HREF/MOP500 series of boards. This also sets the display
regulator to be on at boot so we don't loose our splash
screen when the board comes up.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the board support patch for ab8500 gpio driver
on mach-ux500.Patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Modify for header file placement]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
