Wei Chong Tan reported a fast-PIT-calibration corner-case:
| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.
I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.
The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.
So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.
In other words:
- I'd like to move the PIT MSB check to after the last
iteration, rather than in every iteration
- I think we should comment on the fact that it's also a
serializing instruction and so 'fences in' the TSC read.
Here's a suggested replacement.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix out of scope variable access in sched_slice()
sched: Hide runqueues from direct refer at source code level
sched: Remove unneeded __ref tag
sched, x86: Fix cpufreq + sched_clock() TSC scaling
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] cpumask: new cpumask operators for arch/x86/kernel/cpu/cpufreq/powernow-k8.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c
[CPUFREQ] cpumask: avoid cpumask games in arch/x86/kernel/cpu/cpufreq/speedstep-centrino.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c
[CPUFREQ] powernow-k8: get drv data for correct CPU
[CPUFREQ] powernow-k8: read P-state from HW
[CPUFREQ] reduce scope of ACPI_PSS_BIOS_BUG_MSG[]
[CPUFREQ] Clean up convoluted code in arch/x86/kernel/tsc.c:time_cpufreq_notifier()
[CPUFREQ] minor correction to cpu-freq documentation
[CPUFREQ] powernow-k8.c: mess cleanup
[CPUFREQ] Only set sampling_rate_max deprecated, sampling_rate_min is useful
[CPUFREQ] powernow-k8: Set transition latency to 1 if ACPI tables export 0
[CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case
For freqency dependent TSCs we only scale the cycles, we do not account
for the discrepancy in absolute value.
Our current formula is: time = cycles * mult
(where mult is a function of the cpu-speed on variable tsc machines)
Suppose our current cycle count is 10, and we have a multiplier of 5,
then our time value would end up being 50.
Now cpufreq comes along and changes the multiplier to say 3 or 7,
which would result in our time being resp. 30 or 70.
That means that we can observe random jumps in the time value due to
frequency changes in both fwd and bwd direction.
So what this patch does is change the formula to:
time = cycles * frequency + offset
And we calculate offset so that time_before == time_after, thereby
ridding us of these jumps in time.
[ Impact: fix/reduce sched_clock() jumps across frequency changing events ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chucked-on-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
PIT_TICK_RATE is currently defined in four architectures, but in three
different places. While linux/timex.h is not the perfect place for it, it
is still a reasonable replacement for those drivers that traditionally use
asm/timex.h to get CLOCK_TICK_RATE and expect it to be the PIT frequency.
Note that for Alpha, the actual value changed from 1193182UL to 1193180UL.
This is unlikely to make a difference, and probably can only improve
accuracy. There was a discussion on the correct value of CLOCK_TICK_RATE
a few years ago, after which every existing instance was getting changed
to 1193182. According to the specification, it should be
1193181.818181...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Hellwig noticed the following potential uninitialised use:
> arch/x86/kernel/tsc.c: In function 'time_cpufreq_notifier':
> arch/x86/kernel/tsc.c:634: warning: 'dummy' may be used uninitialized in this function
>
> where we do have CONFIG_SMP set, freq->flags & CPUFREQ_CONST_LOOPS is
> true and ref_freq is false.
It seems plausable, though the circumstances for hitting it are really low.
Nearly all SMP capable cpufreq drivers set CPUFREQ_CONST_LOOPS.
powernow-k8 is really the only exception. The older CPUs were typically
only ever UP. (powernow-k7 never supported SMP for eg)
It's worth fixing regardless, as it cleans up the code.
Fix possible uninitialized use of dummy, by just removing it,
and making the setting of lpj more obvious.
Signed-off-by: Dave Jones <davej@redhat.com>
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, nmi: Use predefined numbers instead of hardcoded one
x86: asm/processor.h: remove double declaration
x86, mtrr: replace MTRRdefType_MSR with msr-index's MSR_MTRRdefType
x86, mtrr: replace MTRRfix4K_C0000_MSR with msr-index's MSR_MTRRfix4K_C0000
x86, mtrr: remove mtrr MSRs double declaration
x86, mtrr: replace MTRRfix16K_80000_MSR with msr-index's MSR_MTRRfix16K_80000
x86, mtrr: replace MTRRfix64K_00000_MSR with msr-index's MSR_MTRRfix64K_00000
x86, mtrr: replace MTRRcap_MSR with msr-index's MSR_MTRRcap
x86: mce: remove duplicated #include
x86: msr-index.h remove duplicate MSR C001_0015 declaration
x86: clean up arch/x86/kernel/tsc_sync.c a bit
x86: use symbolic name for VM86_SIGNAL when used as vm86 default return
x86: added 'ifndef _ASM_X86_IOMAP_H' to iomap.h
x86: avoid multiple declaration of kstack_depth_to_print
x86: vdso/vma.c declare vdso_enabled and arch_setup_additional_pages before they get used
x86: clean up declarations and variables
x86: apic/x2apic_cluster.c x86_cpu_to_logical_apicid should be static
x86 early quirks: eliminate unused function
The *fence instructions were moved to vsyscall_64.c by commit
cb9e35dce9. But this breaks the
vDSO, because vread methods are also called from there.
Besides, the synchronization might be unnecessary for other
time sources than TSC.
[ Impact: fix potential time warp in VDSO ]
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
LKML-Reference: <9d0ea9ea0f866bdc1f4d76831221ae117f11ea67.1243241859.git.ptesarik@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup, no code changed
- syscalls.h update declarations due to unifications
- irq.c declare smp_generic_interrupt() before it gets used
- process.c declare sys_fork() and sys_vfork() before they get used
- tsc.c rename tsc_khz shadowed variable
- apic/probe_32.c declare apic_default before it gets used
- apic/nmi.c prev_nmi_count should be unsigned
- apic/io_apic.c declare smp_irq_move_cleanup_interrupt() before it gets used
- mm/init.c declare direct_gbpages and free_initrd_mem before they get used
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
sched: Add comments to find_busiest_group() function
sched: Refactor the power savings balance code
sched: Optimize the !power_savings_balance during fbg()
sched: Create a helper function to calculate imbalance
sched: Create helper to calculate small_imbalance in fbg()
sched: Create a helper function to calculate sched_domain stats for fbg()
sched: Define structure to store the sched_domain statistics for fbg()
sched: Create a helper function to calculate sched_group stats for fbg()
sched: Define structure to store the sched_group statistics for fbg()
sched: Fix indentations in find_busiest_group() using gotos
sched: Simple helper functions for find_busiest_group()
sched: remove unused fields from struct rq
sched: jiffies not printed per CPU
sched: small optimisation of can_migrate_task()
sched: fix typos in documentation
sched: add avg_overlap decay
x86, sched_clock(): mark variables read-mostly
sched: optimize ttwu vs group scheduling
sched: TIF_NEED_RESCHED -> need_reshed() cleanup
sched: don't rebalance if attached on NULL domain
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (35 commits)
[CPUFREQ] Prevent p4-clockmod from auto-binding to the ondemand governor.
[CPUFREQ] Make cpufreq-nforce2 less obnoxious
[CPUFREQ] p4-clockmod reports wrong frequency.
[CPUFREQ] powernow-k8: Use a common exit path.
[CPUFREQ] Change link order of x86 cpufreq modules
[CPUFREQ] conservative: remove 10x from def_sampling_rate
[CPUFREQ] conservative: fixup governor to function more like ondemand logic
[CPUFREQ] conservative: fix dbs_cpufreq_notifier so freq is not locked
[CPUFREQ] conservative: amend author's email address
[CPUFREQ] Use swap() in longhaul.c
[CPUFREQ] checkpatch cleanups for acpi-cpufreq
[CPUFREQ] powernow-k8: Only print error message once, not per core.
[CPUFREQ] ondemand/conservative: sanitize sampling_rate restrictions
[CPUFREQ] ondemand/conservative: deprecate sampling_rate{min,max}
[CPUFREQ] powernow-k8: Always compile powernow-k8 driver with ACPI support
[CPUFREQ] Introduce /sys/devices/system/cpu/cpu*/cpufreq/cpuinfo_transition_latency
[CPUFREQ] checkpatch cleanups for powernow-k8
[CPUFREQ] checkpatch cleanups for ondemand governor.
[CPUFREQ] checkpatch cleanups for powernow-k7
[CPUFREQ] checkpatch cleanups for speedstep related drivers.
...
In order for ntpd to correctly synchronize the clocks, the frequency of
the system clock must not be off by more than 500 ppm (or, put another
way, 1:2000), or ntpd will end up giving up on trying to synchronize
properly, and ends up reseting the clock in jumps instead.
The fast TSC PIT calibration sometimes failed this test - it was
assuming that the PIT reads always took about one microsecond each (2us
for the two reads to get a 16-bit timer), and that calibrating TSC to
the PIT over 15ms should thus be sufficient to get much closer than
500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm
error value).
However, that assumption does not always hold: apparently some hardware
is either very much slower at reading the PIT registers, or there was
other noise causing at least one machine to get 700+ ppm errors.
So instead of using a fixed 15ms timing loop, this changes the fast PIT
calibration to read the TSC delta over the individual PIT timer reads,
and use the result to calculate the error bars on the PIT read timing
properly. We then successfully calibrate the TSC only if the maximum
error bars fall below 500ppm.
In the process, we also relax the timing to allow up to 25ms for the
calibration, although it can happen much faster depending on hardware.
Reported-and-tested-by: Jesper Krogh <jesper@krogh.cc>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: micro-optimization
There's a number of variables in the sched_clock() path that are
in .data/.bss - but not marked __read_mostly. This creates the
danger of accidental false cacheline sharing with some other,
write-often variable.
So mark them __read_mostly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
http://bugzilla.kernel.org/show_bug.cgi?id=10968
[ Updated for current tree, and fixed compile failure
when p4-clockmod was built modular -- davej]
From: Matthias-Christian Ott <ott@mirix.org>
Signed-off-by: Dominik Brodowski <linux@brodo.de>
Signed-off-by: Dave Jones <davej@redhat.com>
The x86/Voyager subarch used to have this distinction between
'x86 SMP support' and 'Voyager SMP support':
config X86_SMP
bool
depends on SMP && ((X86_32 && !X86_VOYAGER) || X86_64)
This is a pointless distinction - Voyager can (and already does) use
smp_ops to implement various SMP quirks it has - and it can be extended
more to cover all the specialities of Voyager.
So remove this complication in the Kconfig space.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
sched_clock() uses cycles_2_ns() needlessly - which is an irq-disabling
variant of __cycles_2_ns().
Most of the time sched_clock() is called with irqs disabled already.
The few places that call it with irqs enabled need to be updated.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix udelay when "notsc" boot parameter is passed
With notsc passed on commandline, tsc may not be used for
udelays, make sure that we do not use tsc_khz to calculate
the lpj value in such cases.
Reported-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Changes timekeeping on Vmware (or with tsc=reliable).
This is achieved by resetting the CLOCKSOURCE_MUST_VERIFY flag.
We add a tsc=reliable commandline option to enable this.
This enables legacy hardware without HPET, LAPIC, or ACPI timers
to enter high-resolution timer mode.
Along with that have extended this to be used in virtualization environement
too. Now we also set this flag if the X86_FEATURE_TSC_RELIABLE bit is set.
This is important since there is a wrap-around problem with the acpi_pm timer.
The acpi_pm counter is just 24bits and this can overflow in ~4 seconds. With
the NO_HZ kernels in virtualized environment, there can be situations when
the guest is descheduled for longer duration, as a result we may miss the wrap
of the acpi counter. When TSC is used as a clocksource and acpi_pm timer is
being used as the watchdog clocksource this error in acpi_pm results in TSC
being marked as unstable, and essentially results in time dropping in chunks
of 4 seconds whenever this wrap is missed. Since the virtualized TSC is
reliable on VMware, we should always use the TSCs clocksource on VMware, so
we skip the verfication at runtime, by checking for the feature bit.
Since we reset the flag for mgeode systems too, i have combined
the mgeode case with the feature bit check.
Signed-off-by: Jeff Hansen <jhansen@cardaccess-inc.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Changes timebase calibration on Vmware.
v3->v2 : Abstract the hypervisor detection and feature (tsc_freq) request
behind a hypervisor.c file
v2->v1 : Add a x86_hyper_vendor field to the cpuinfo_x86 structure.
This avoids multiple calls to the hypervisor detection function.
This patch adds function to detect if we are running under VMware.
The current way to check if we are on VMware is following,
# check if "hypervisor present bit" is set, if so read the 0x40000000
cpuid leaf and check for "VMwareVMware" signature.
# if the above fails, check the DMI vendors name for "VMware" string
if we find one we query the VMware hypervisor port to check if we are
under VMware.
The DMI + "VMware hypervisor port check" is needed for older VMware products,
which don't implement the hypervisor signature cpuid leaf.
Also note that since we are checking for the DMI signature the hypervisor
port should never be accessed on native hardware.
This patch also adds a hypervisor_get_tsc_freq function, instead of
calibrating the frequency which can be error prone in virtualized
environment, we ask the hypervisor for it. We get the frequency from
the hypervisor by accessing the hypervisor port if we are running on VMware.
Other hypervisors too can add code to the generic routine to get frequency on
their platform.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: fix x86/Voyager boot
CONFIG_SMP is used for features which work on *all* x86 boxes.
CONFIG_X86_SMP is used for standard PC like x86 boxes (for things like
multi core and apics)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce a fast TSC-calibration method on sane hardware.
It only uses 17920 PIT timer ticks to calibrate the TSC, plus 256 ticks on
each side to make sure the TSC values were very close to the tick, so the
whole calibration takes 15ms. Yet, despite only takign 15ms,
we can actually give pretty stringent guarantees of accuracy:
- the code requires that we hit each 256-counter block at least 50 times,
so the TSC error is basically at *MOST* just a few PIT cycles off in
any direction. In practice, it's going to be about one microseconds
off (which is how long it takes to read the counter)
- so over 17920 PIT cycles, we can pretty much guarantee that the
calibration error is less than one half of a percent.
My testing bears this out: on my machine, the quick-calibration reports
2934.085kHz, while the slow one reports 2933.415.
Yes, the slower calibration is still more precise. For me, the slow
calibration is stable to within about one hundreth of a percent, so it's
(at a guess) roughly an order-and-a-half of magnitude more precise. The
longer you wait, the more precise you can be.
However, the nice thing about the fast TSC PIT synchronization is that
it's pretty much _guaranteed_ to give that 0.5% precision, and fail
gracefully (and very quickly) if it doesn't get it. And it really is
fairly simple (even if there's a lot of _details_ there, and I didn't get
all of those right ont he first try or even the second ;)
The patch says "110 insertions", but 63 of those new lines are actually
comments.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
arch/x86/kernel/tsc.c | 111 ++++++++++++++++++++++++++++++++++++++++++++++++-
1 files changed, 110 insertions(+), 1 deletions(-)
The last changes made the calibration loop 250ms long which is far
too much. Try to do that more clever.
Experiments have shown that using a 10ms delay for the PIT based calibration
gives us a good enough value. If we have a reference (HPET/PMTIMER) and the
result of the PIT and the reference is close enough, then we can break out of
the calibration loop on a match right away and use the reference value.
Otherwise we just loop 3 times and decide then, which value to take.
One caveat is that for virtualized environments the PIT calibration often does
not work at all and I found out that 10us is a bit too short as well for the
reference to give a sane result. The solution here is to make the last loop
longer when the first two PIT calibrations failed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When calibration against PIT fails, the warning that we print is misleading.
In a virtualized environment the VM may get descheduled while calibration
or, the check in PIT calibration may fail due to other virtualization
overheads.
The warning message explicitly assumes that calibration failed due to SMI's
which may not be the case. Change that to something proper.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSC calibration function is still very complicated, but this makes
it at least a little bit less so by moving the PIT part out into a
helper function of its own.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Larry Finger reported at http://lkml.org/lkml/2008/9/1/90:
An ancient laptop of mine started throwing errors from b43legacy when
I started using 2.6.27 on it. This has been bisected to commit bfc0f59
"x86: merge tsc calibration".
The unification of the TSC code adopted mostly the 64bit code, which
prefers PMTIMER/HPET over the PIT calibration.
Larrys system has an AMD K6 CPU. Such systems are known to have
PMTIMER incarnations which run at double speed. This results in a
miscalibration of the TSC by factor 0.5. So the resulting calibrated
CPU/TSC speed is half of the real CPU speed, which means that the TSC
based delay loop will run half the time it should run. That might
explain why the b43legacy driver went berserk.
On the other hand we know about systems, where the PIT based
calibration results in random crap due to heavy SMI/SMM
disturbance. On those systems the PMTIMER/HPET based calibration logic
with SMI detection shows better results.
According to Alok also virtualized systems suffer from the PIT
calibration method.
The solution is to use a more wreckage aware aproach than the current
either/or decision.
1) reimplement the retry loop which was dropped from the 32bit code
during the merge. It repeats the calibration and selects the lowest
frequency value as this is probably the closest estimate to the real
frequency
2) Monitor the delta of the TSC values in the delay loop which waits
for the PIT counter to reach zero. If the maximum value is
significantly different from the minimum, then we have a pretty safe
indicator that the loop was disturbed by an SMI.
3) keep the pmtimer/hpet reference as a backup solution for systems
where the SMI disturbance is a permanent point of failure for PIT
based calibration
4) do the loop iteration for both methods, record the lowest value and
decide after all iterations finished.
5) Set a clear preference to PIT based calibration when the result
makes sense.
The implementation does the reference calibration based on
HPET/PMTIMER around the delay, which is necessary for the PIT anyway,
but keeps separate TSC values to ensure the "independency" of the
resulting calibration values.
Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6
(affected machine with a double speed pmtimer which I grabbed out of
the dump), Pentium class machines and AMD/Intel 64 bit boxen.
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that my sched_clock() was slow on a number of machine, so I
started looking at cpufreq.
The below seems to fix the problem for me.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: crash on non-TSC-equipped CPUs
Don't enable the TSC notifier if we *either*:
1. don't have a CPU, or
2. have a CPU with constant TSC.
In either of those cases, the notifier is either damaging (1) or useless(2).
From: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
WARNING: vmlinux.o(.text+0x7950): Section mismatch in reference from the function native_calibrate_tsc() to the function .init.text:tsc_read_refs()
The function native_calibrate_tsc() references
the function __init tsc_read_refs().
This is often because native_calibrate_tsc lacks a __init
annotation or the annotation of tsc_read_refs is wrong.
tsc_read_refs is called from native_calibrate_tsc which is not __init
and native_calibrate_tsc cannot be marked __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dave Hansen reported a build error on 32bit which went unnoticed
as newer gcc versions seem to optimize unused static functions
away before compiling them.
Make vread_tsc() depend on CONFIG_X86_64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Integration generated a duplicate call to use_tsc_delay.
Particularly, the one that is done before we check for general
tsc usability seems wrong.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is for consistency with i386. We call use_tsc_delay()
at tsc initialization for x86_64, so we'll be always using it.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the paravirtualized calculate_cpu_khz to calibrate_tsc.
In all cases, we actually calibrate_tsc and use that as the cpu_khz value.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unify the clocksource code.
Unify the tsc_init code.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge the tsc calibration code for the 32bit and 64bit kernel.
The paravirtualized calculate_cpu_khz for 64bit now points to the correct
tsc_calibrate code as in 32bit.
Original native_calculate_cpu_khz for 64 bit is now called as calibrate_cpu.
Also moved the recalibrate_cpu_khz function in the common file.
Note that this function is called only from powernow K7 cpu freq driver.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the basic global variable definitions and sched_clock handling in the
common "tsc.c" file.
- Unify notsc kernel command line handling for 32 bit and 64bit.
- Functional changes for 64bit.
- "tsc_disabled" is updated if "notsc" is passed at boottime.
- Fallback to jiffies for sched_clock, incase notsc is passed on
commandline.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Hecht <dhecht@vmware.com>
Cc: Dan Hecht <dhecht@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
