This adds support for DVB-T mode only, analog mode is not supported.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for composite and s-video inputs on
Avermedia DVB-S Pro and DVB-S Hybrid+FM cards
(both labled A700) to the saa7134 driver.
XC2028 support for Hybrid+FM is still missing.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018).
This patch adds proper support for radio, video, s-video, composite and ATSC.
However, support for radio and video depends on having s5h1409 i2c gate open,
otherwise, xc30x8 chip won't be visible.
For a better support, some rework is needed on cx88 driver, to allow adding
xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address.
Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure
out the proper parameters for s5h1409 and the GPIO pins used by each
configuration.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TV reception ok. S-video and Composite not tested. Audio not tested.
IR not implemented yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have what looks like a Geovision GV-600 (or 650) card. It has a large
chip in the middle labeled
CONEXANT
FUSION 878A
25878-13
E345881.1
0312 TAIWAN
It has an audio connector coming out from a chip labeled
ATMEL
0242
AT89C2051-24PI
It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)
...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dfffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
01:0a.1 0480: 109e:0878 (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dffff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.
Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Signed-off-by: Ernesto Hernández-Novich <emhn@usb.ve>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix GPIO for FusionHDTV 7 Gold tv / s-video / composite input selection.
Fix card textual name to match other FusionHDTV device names.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the following saa7134 xc3028 based boards:
132 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
133 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
134 -> Avermedia M115 [1461:a836]
135 -> Compro VideoMate T750 [185b:c900]
This is based on a original patch thanks to Markus Rechberger that added xc3028
gpio init code for the above boards.
This patch moves saa7134_tuner_callback to saa7134-cards, originally used only
by tda8290 DVB-S boards. The callback was made more generic to support other
tuners.
Currently, it supports both tda8290 and xc2028/xc3028 tuners. Added also the
basis for xc5000 tuner callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for tuning DVB-T channels on DViCO's FusionHDTV DVB-T Pro board.
The IR remote and analog tuner are not supported at this time.
Some changes made by Mauro Chehab to allow merging it with some other xc3028
patches.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ports a patch from Markus Rechberger to work with tuner-xc2028.
It adds entries for several cx88 boards with xc2038/3028 tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
load ir-kbd-i2c for IR remote control support on DViCO FusionHDTV 5 PCI nano
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC is known to work.
SVideo / Composite should work (I have no cable to test).
Analog tuner support does not work.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Show peer group ID of nearest dominating group that has intersection
with the mount's namespace.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mszeredi@suse.cz] rewrite and split big patch into managable chunks
/proc/mounts in its current form lacks important information:
- propagation state
- root of mount for bind mounts
- the st_dev value used within the filesystem
- identifier for each mount and it's parent
It also suffers from the following problems:
- not easily extendable
- ambiguity of mountpoints within a chrooted environment
- doesn't distinguish between filesystem dependent and independent options
- doesn't distinguish between per mount and per super block options
This patch introduces /proc/<pid>/mountinfo which attempts to address
all these deficiencies.
Code shared between /proc/<pid>/mounts and /proc/<pid>/mountinfo is
extracted into separate functions.
Thanks to Al Viro for the help in getting the design right.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
DOC: A couple corrections and clarifications in USB doc.
Generate a slightly more informative error msg for bad HZ
fix typo "is" -> "if" in Makefile
ext*: spelling fix prefered -> preferred
DOCUMENTATION: Use newer DEFINE_SPINLOCK macro in docs.
KEYS: Fix the comment to match the file name in rxrpc-type.h.
RAID: remove trailing space from printk line
DMA engine: typo fixes
Remove unused MAX_NODES_SHIFT
MAINTAINERS: Clarify access to OCFS2 development mailing list.
V4L: Storage class should be before const qualifier (sn9c102)
V4L: Storage class should be before const qualifier
sonypi: Storage class should be before const qualifier
intel_menlow: Storage class should be before const qualifier
DVB: Storage class should be before const qualifier
arm: Storage class should be before const qualifier
ALSA: Storage class should be before const qualifier
acpi: Storage class should be before const qualifier
firmware_sample_driver.c: fix coding style
MAINTAINERS: Add ati_remote2 driver
...
Fixed up trivial conflicts in firmware_sample_driver.c
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
block: fix blk_register_queue() return value
block: fix memory hotplug and bouncing in block layer
block: replace remaining __FUNCTION__ occurrences
Kconfig: clean up block/Kconfig help descriptions
cciss: fix warning oops on rmmod of driver
cciss: Fix race between disk-adding code and interrupt handler
block: move the padding adjustment to blk_rq_map_sg
block: add bio_copy_user_iov support to blk_rq_map_user_iov
block: convert bio_copy_user to bio_copy_user_iov
loop: manage partitions in disk image
cdrom: use kmalloced buffers instead of buffers on stack
cdrom: make unregister_cdrom() return void
cdrom: use list_head for cdrom_device_info list
cdrom: protect cdrom_device_info list by mutex
cdrom: cleanup hardcoded error-code
cdrom: remove ifdef CONFIG_SYSCTL
A couple of corrections and clarifications in USB
documentation.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
Remove BitKeeper from dontdiff. Point to the klibc git repository
instead of old BitKeeper ones.
Signed-off-by: Cyril Brulebois <cyril.brulebois@kerlabs.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Now unregister_cdrom() always returns 0.
Make it return void and update all callers that check the return value.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Vital Product Data (VPD) may be exposed by PCI devices in several
ways. It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.
This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
(in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
operations defined
It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for batching up the flushing of the IOTLB for the DMAR
implementation found in the Intel VT-d hardware. It works by building a list
of to be flushed IOTLB entries and a bitmap list of which DMAR engine they are
from.
After either a high water mark (250 accessible via debugfs) or 10ms the list
of iova's will be reclaimed and the DMAR engines associated are IOTLB-flushed.
This approach recovers 15 to 20% of the performance lost when using the IOMMU
for my netperf udp stream benchmark with small packets. It can be disabled
with a kernel boot parameter "intel_iommu=strict".
Its use does weaken the IOMMU protections a bit.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently keep 2 lists of PCI devices in the system, one in the
driver core, and one all on its own. This second list is sorted at boot
time, in "BIOS" order, to try to remain compatible with older kernels
(2.2 and earlier days). There was also a "nosort" option to turn this
sorting off, to remain compatible with even older kernel versions, but
that just ends up being what we have been doing from 2.5 days...
Unfortunately, the second list of devices is not really ever used to
determine the probing order of PCI devices or drivers[1]. That is done
using the driver core list instead. This change happened back in the
early 2.5 days.
Relying on BIOS ording for the binding of drivers to specific device
names is problematic for many reasons, and userspace tools like udev
exist to properly name devices in a persistant manner if that is needed,
no reliance on the BIOS is needed.
Matt Domsch and others at Dell noticed this back in 2006, and added a
boot option to sort the PCI device lists (both of them) in a
breadth-first manner to help remain compatible with the 2.4 order, if
needed for any reason. This option is not going away, as some systems
rely on them.
This patch removes the sorting of the internal PCI device list in "BIOS"
mode, as it's not needed at all anymore, and hasn't for many years.
I've also removed the PCI flags for this from some other arches that for
some reason defined them, but never used them.
This should not change the ordering of any drivers or device probing.
[1] The old-style pci_get_device and pci_find_device() still used this
sorting order, but there are very few drivers that use these functions,
as they are deprecated for use in this manner. If for some reason, a
driver rely on the order and uses these functions, the breadth-first
boot option will resolve any problem.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Create Documentation/PCI/ and move PCI-related files to it.
Fix a few instances of trailing whitespace.
Update references to the new file locations.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Requiring userspace to close and re-open sysfs attributes has been the
policy since before 2.6.12. It allows userspace to get a consistent
snapshot of kernel state and consume it with incremental reads and seeks.
Now, if the file position is zero the kernel assumes userspace wants to see
the new value. The application for this change is to allow a userspace
RAID metadata handler to check the state of an array without causing any
memory allocations. Thus not causing writeback to a raid array that might
be blocked waiting for userspace to take action.
Cc: Neil Brown <neilb@suse.de>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.
What is iSCSI Boot Firmware Table? It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target. Currently the iSCSI
information is hard-coded in the initrd. The /sysfs entries are read-only
one-name-and-value fields.
The usual set of data exposed is:
# for a in `find /sys/firmware/ibft/ -type f -print`; do echo -n "$a: "; cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0
For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf
[akpm@linux-foundation.org: fix build]
Signed-off-by: Konrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Source file was removed. Need to remove docbook reference also.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavel Machek <pavel@suse.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the PM core to protect its data structures, specifically the
dpm_active list, from being corrupted if a child of the currently
suspending device is registered concurrently with its ->suspend()
callback. In that case, since the new device (the child) is added
to dpm_active after its parent, the PM core will attempt to
suspend it after the parent, which is wrong.
Introduce a new member of struct dev_pm_info, called 'sleeping',
and use it to check if the parent of the device being added to
dpm_active has been suspended, in which case the device registration
fails. Also, use 'sleeping' for checking if the ordering of devices
on dpm_active is correct.
Introduce variable 'all_sleeping' that will be set to 'true' once all
devices have been suspended and make new device registrations fail
until 'all_sleeping' is reset to 'false', in order to avoid having
unsuspended devices around while the system is going into a sleep state.
Remove pm_sleep_rwsem which is not necessary any more.
Special thanks to Alan Stern for discussions and suggestions that
lead to the creation of this patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the firmware_class sample drivers to samples/ so that they are
buildable and can be maintained.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Viktor was nice enough to enhance the document based on my replies to
his questions on the subject.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces new feature of cpuset - sched domain customization.
This version provides a per-cpuset file 'sched_relax_domain_level' that
enable us to change the searching range of scheduler, which used to limit
how many cpus the scheduler searches at some schedule events, such as
wakening task and running out of runqueue.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we merge the iommu initialization parameters in pci-dma.c
Nice thing, that both architectures at least recognize the same
parameters.
usedac i386 parameter is marked for deprecation
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds three tests that test whether the PR_GET_TSC and
PR_SET_TSC commands have the desirable effect.
The tests check whether the control register is updated correctly
at context switches and try to discover bugs while enabling/disabling
the timestamp counter.
Signed-off-by: Erik Bosman <ejbosman@cs.vu.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- noexec32 is on by default for years already
- add noexec32 to kernel-parameters and fix noexec typo in there
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
