This patch adds DMA operation clock which is disabled as default.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add cose related to regulator. To control powre consumeption
have registered the voltage consumer of WM8994 to the regulator framework.
Additionally, I explain the constraints of the regulator of WM8994 codec.
All these consumer supply of WM8994 codec connected the regulator(VCC_1.8V)
on a circuit diagram. "VCC_1.8V" regulator is always enabled, because it is
used to many devices on Goni/Aquila board. This is required especially
when there are many devices physically attached to "VCC_1.8V" and some of
they did not "register" as consumers to "VCC_1.8V". "VCC_1.8V" might be
turned off by those who are registered while "unregistered" are still active
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add initialization code of audio and I2S platform drivers
to Goni and Aquila board.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch the I2C board information for the WM8994 used in the Goni/Aquila
as audio codec and adds the I2C platform drivers.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds warning about changing EPLL rate to notice that other
driver that controls H/W, which is using EPLL, will has unknown effects
by this EPLL rate change.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds audio clocks(SCLK_AUDIO{0,1,2} and SCLK_AUDIO) to be
initial as a sysclk on boot-time.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add SCLK_SPDIF clock to support source clock of S/PDIF
on S5PV210.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add S/PDIF platform device to support S/PDIF PCM audio
on S5PV210.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds ARCH_HAS_CPUFREQ in arch/arm/Kconfig for S5PV210,
and updates mach-s5pv210/Makefile for supporting build CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CPUFREQ driver for supporting DFS(Dynamic Frequency Scaling).
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds some CMU(Clock Management Unit) registers for
supporting CPUFREQ and some drivers.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds MOUT_DMC0 and SCLK_DMC0 for checking the dmc0 clock
in CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current fout_apll has fixed rate value. So CPUFREQ driver gets
incorrect value when finding current CPU frequency. Because some
operation level need to change APLL.
Added get_rate function for fout_apll can give correct frequency
value when calling get_rate function.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The name of the I2C2 and I2C3 interrupt should be IIC2 and IIC3
instead of CAN0 and CAN1.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: coding-style fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for QT602240 touchscreen on I2C2 bus.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for si470x radio device on Samsung
Goni board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for S6E63M0 LCD controller on Samsung
Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
[kgene.kim@samsung.com: fix build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds suspend-to-ram support for S5PV210.
Note. This patch is confirmed on SMDKV210 and SMDKC110 board.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error by S3C2410 PM Suspend debug option
due to undefined address.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S5P SoCs have the same interrupt type defines for both
external interrupts and gpio interrupts. This patch removes all
duplicates from S5PC100 and S5PV210 specific includes as well as
gpio interrupt code and put a common defines to plat/irqs.h
NOTE: Do not use this for S5P6440 and S5P6450.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: add note for S5P64X0]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common callback for gpio_to_irq() for external and
gpio interrupts for Samsung SoCs.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: moved samsung_gpiolib_to_irq() for s3c24xx build]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV210/S5PC110 can use common S5P GPIO interrupt code.
This patch adds required defines and code to make use of it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add the necessary definitions and mapping information to enable the
s3c-hsotg gadget to build.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for MMC power regulators on Samsung
Goni board. GPIO pin GONI_EXT_FLASH_EN has been transferred from machine
startup code to fixed voltage regulator.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for s3c-hsotg driver to enable usb
gadget support on Samsung Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 67a38950f0917aecfe1a3e46720d8bbb0020 there is no need
to set pixel clock for the s3c-fb driver's window information.
The correct pixel clock value can be automatically calculated from
the other screen parameters. This patch removes the redundant pixel clock
parameter.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the default upper_margin and vsync_len to get rid of repeated last
line on the display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The selection PLAT_S5P is selected with plat-s5p/Kconfig.
So remove it form each CPU_S5PXXXX config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case of S5PV210/S5PC110, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV210 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds to support Torbreck board of aESOP community using
Samsung S5PV210 SoC.
Signed-off-by: Kyuho Choi <chlrbgh0@gmail.com>
Signed-off-by: Hyunchul Ko <ghcstop@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMC(DRAM Memory Controller) map_desc table.
Because some driver such as CPUFREQ need to access DMC register.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the GONI board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves some initial maps from plat-s5p to machine,
so that can merge mach-s5p6440 and mach-s5p6450.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves OneNAND device definitions from mach-s5pv210 to plat-s5p
so that can support it commonly.
Note: S5PC110 and S5PC210 have same OneNAND driver.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds header <linux/sched.h> into the below files for build with
CONFIG_PREEMPT_NONE.
arch/arm/mach-s5p6440/cpu.c
arch/arm/mach-s5p6442/cpu.c
arch/arm/mach-s5pc100/cpu.c
arch/arm/mach-s5pv210/cpu.c
Following is error message of in case of s5pv210_defconfig with CONFIG_PREEMPT_NONE.
arch/arm/mach-s5pv210/cpu.c:91: error: implicit declaration of function 'need_resched'
Signed-off-by: SeungChull Suh <sc.suh@samsung.com>
[kgene.kim@samsung.com: removed mach-s5p64x0/cpu.c]
[kgene.kim@samsung.com: added fix mach-s5p6440/cpu.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes following unused codes for removing build warnings.
arch/arm/plat-samsung/adc.c:438: warning: unused variable 'flags'
arch/arm/mach-s5pv210/clock.c:176: warning: 's5pv210_clk_ip4_ctrl' defined but not used
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These clocks enables FIMC driver to operate on machines, which
bootloader power gated FIMC devices to save power on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
CLK_GATE_IP3[8] is RESERVED. The port "I2C_HDMI_DDC" of CLK_GATE_IP3[10] is
used as another I2C port. Therefore, defined the unused I2C-1 as another I2C
there was left undefined but used.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Silences following build warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:644: warning: format '%08lx' expects type 'long
unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
