It will be replaced with automatic deemphasis rate configuration but since
we have an enumeration table in this driver this is done in a separate
commit to make the renumbering of the enumeration items clear.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds sound support for the SmartQ board.
The hardware consists of a S3C6410 coupled with a WM8987 over I²S. The WM8750
driver is used for driving the WM8987, as they are register compatible.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8987 codec is register compatible with the WM8750, so just add it to the
SPI and I²C device table.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For UDA1341 codec power control is managed in STATUS1 register, and
for all other codecs in DATA011 register.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In UDA1340, UDA1344 and UDA1345 codecs there is one more functional
register in part of DATA0 tranfser. For UDA1341 this register
coincides with EA register.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On initialization ADC/DAC are enabled only for UDA1341, that's why
bias_level shall be set to off explicitly, otherwise dapm is
misinformed about bias_level on startup.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change wipes out a hardcoded macro, which enables codec bias
level control. Now is_powered_on_standby value shall be used instead.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds GPIO jack detection to Nokia N900/RX-51. At the moment only
SND_JACK_VIDEOOUT type is reported. More types could be reported after
getting more audio features supported and necessary drivers integrated for
implementing automated accessory detection.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Nokia RX-51/N900 has multifunction 4-pole audio-video jack that can be used
as headphone, headset or audio-video connector. This patch implements the
control 'Jack Function' which is used to select the desired function.
At the moment only TV-out without audio is supported.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
in tlv320aic23_set_bias_level, for the case SND_SOC_BIAS_ON, the
comment says "vref/mid, osc on, dac unmute" but the code doesn't
clear the corresponding bits, thus when resuming, several bits are
not cleared preventing the codec from working.
in tlv320aic23_suspend, clearing the active register is not needed
as it will be done by tlv320aic23_set_bias_level, when setting
bias to SND_SOC_BIAS_OFF
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: broonie@opensource.wolfsonmicro.com
Cc: anuj.aggarwal@ti.com
Cc: lrg@slimlogic.co.uk
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds ASoC support for the qi_lb60 board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the JZ4740 internal codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds ASoC support for JZ4740 SoCs I2S module.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After mass production started it was found that several boards exhibit
noise problems during sound playback. After some investigation it was
determined that CLKX polarity is set incorrectly, and even if most boards
can tolerate the wrong setting, there are some that don't.
Fix polarity setup in the board file. As the clock settings for input and
output now match, merge in and out functions and structures to simplify
code.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When SX_TLV widgets are read, if the gain is set to a value below 0dB,
the mixer control is erroniously read as being at maximum volume.
The value read out of the CODEC register is never sign-extended, and
when the minimum value is subtracted (read; added, since the minimum is
negative) the result is a number greater than the maximum allowed value
for the control, and hence it saturates.
Solution: Mask the result so that it "wraps around", emulating
sign-extension.
Signed-off-by: Stuart Longland <redhatter@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* tdm slot has to be configured to get sound working on i.MX25
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The config option SND_FSI_AK4642 selects SND_SOC_AK4642 which in turn
enables the compilation of ak4642.c - however this codec uses I2C to
communicate with the HW.
Same applies to DA7210.
Consequently when I2C is not set, the compilation fails [1]
This patch fixes this issues, by adding a depencdency on the related HW-
controller.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The most useful configuration for the WM2000 is to enable the ANC so turn
that on by default, and since we're not reflecting chip default state also
enable the speaker output by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
On DA830/OMAP-L137 and DA850/OMAP-L138 SoCs, the McASP peripheral
has FIFO support. This FIFO provides additional data buffering. It
also provides tolerance to variation in host/DMA controller response
times. More details of the FIFO operation can be found at
http://focus.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=sprufm1&fileType=pdf
Existing sequence of steps for audio playback/capture are:
a. DMA configuration
b. McASP configuration (configures and enables FIFO)
c. Start DMA
d. Start McASP (enables FIFO)
During McASP configuration, while FIFO was being configured, FIFO
was being enabled in davinci_hw_common_param() function of
sound/soc/davinci/davinci-mcasp.c file. This generated a transmit
DMA event, which gets serviced when DMA is started.
https://patchwork.kernel.org/patch/84611/ patch clears the DMA
events before starting DMA, which is the right thing to do. But
this resulted in a state where DMA was waiting for an event from
McASP (after step c above), but the event which was already there,
has got cleared (because of step b above).
The fix is not to enable the FIFO during McASP configuration as
FIFO was being enabled as part of McASP start.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The header contains an extern that isn't used by anything. Remove.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is to change 'auido.h' to 'audio.h' for
fixing nuc900 alsa driver build error.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for i2s audio on Bluewater Systems Snapper CL15 module
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch to remove the 'break;', when the 'switch' jumps to
the 'default' branch, the 'return -EINVAL' will be return with
a error number, so the 'break;' code never be run, it is unuseful
and should be removed here.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove break after return, it is not needed.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Upper threshold is used in mode7 of DAC33.
Instead of hard wired UTHR, add control to change the upper threshold
value.
Changing upper threshold is not allowed when the playback is already
running, since wrongly timed change in the UTHR can cause problems
with the codec.
With this control the length of the burst in mode7 can be changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add the necessary files to support the TLV320AIC23B wired in I2S
on our i.MX platforms.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* introduce 3 new flags to allow a more detailed configuration
of the SSI link :
IMX_SSI_NET : enable Network Mode
IMX_SSI_SYN : enable Synchronous Mode
IMX_SSI_USE_I2S_SLAVE : enable I2S Slave Mode
* new platform can use these settings without breaking actual
platforms.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The variable 'state' of structure 's3c_ac97_info' seems no use here,
so this patch is to remove the unnecessary variable.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The variable 'periods' of structure 'atmel_runtime_data'
seems no use in whole atmel alsa driver,so I make a patch
to remove the unnecessary variable.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the resource_size function instead of manually calculating the
resource size.This patch can reduce the chance of introducing off-by-one
errors.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OMAP McBSP FIFO is word structured:
McBSP2 has 1024 + 256 = 1280 word long buffer,
McBSP1,3,4,5 has 128 word long buffer
This means, that the size of the FIFO
depends on the McBSP word size configuration.
For example on McBSP3:
16bit samples: size is 128 * 2 = 256 bytes
32bit samples: size is 128 * 4 = 512 bytes
It is simpler to place constraint for buffer and period based on channels.
McBSP3 as example again (16 or 32 bit samples):
1 channel (mono): size is 128 frames (128 words)
2 channels (stereo): size is 128 / 2 = 64 frames (2 * 64 words)
4 channels: size is 128 / 4 = 32 frames (4 * 32 words)
Use the second method to place hw_rule on buffer size, and in threshold
mode to period size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Save the word length configuration of McBSP, and use that information
to calculate, and configure the threshold in McBSP.
Previously the calculation was only correct when the stream had 16bit
audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The size calculation is end - start + 1. But,sometimes, the '1' can
be forgotten carelessly, witch will have potential risk, so use resource_size
for {request/release}_mem_region and ioremap here should be good habit.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Daniel Glöckner <dg@emlix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
